[ARM] 4757/1: [AT91] UART initialization

Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.

The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.

As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-at91/at91rm9200_devices.c

@@ -884,17 +884,21 @@ static struct platform_device at91rm9200_uart0_device = {
 	.num_resources	= ARRAY_SIZE(uart0_resources),
 };
 
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PA17, 1);		/* TXD0 */
 	at91_set_A_periph(AT91_PIN_PA18, 0);		/* RXD0 */
+
+	if (pins & ATMEL_UART_CTS)
 		at91_set_A_periph(AT91_PIN_PA20, 0);	/* CTS0 */
 
+	if (pins & ATMEL_UART_RTS) {
 		/*
 		 * AT91RM9200 Errata #39 - RTS0 is not internally connected to PA21.
 		 *  We need to drive the pin manually.  Default is off (RTS is active low).
 		 */
 		at91_set_gpio_output(AT91_PIN_PA21, 1);
+	}
 }
 
 static struct resource uart1_resources[] = {
@@ -929,15 +933,22 @@ static struct platform_device at91rm9200_uart1_device = {
 	.num_resources	= ARRAY_SIZE(uart1_resources),
 };
 
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
 {
-	at91_set_A_periph(AT91_PIN_PB18, 0);		/* RI1 */
-	at91_set_A_periph(AT91_PIN_PB19, 0);		/* DTR1 */
 	at91_set_A_periph(AT91_PIN_PB20, 1);		/* TXD1 */
 	at91_set_A_periph(AT91_PIN_PB21, 0);		/* RXD1 */
+
+	if (pins & ATMEL_UART_RI)
+		at91_set_A_periph(AT91_PIN_PB18, 0);	/* RI1 */
+	if (pins & ATMEL_UART_DTR)
+		at91_set_A_periph(AT91_PIN_PB19, 0);	/* DTR1 */
+	if (pins & ATMEL_UART_DCD)
 		at91_set_A_periph(AT91_PIN_PB23, 0);	/* DCD1 */
+	if (pins & ATMEL_UART_CTS)
 		at91_set_A_periph(AT91_PIN_PB24, 0);	/* CTS1 */
+	if (pins & ATMEL_UART_DSR)
 		at91_set_A_periph(AT91_PIN_PB25, 0);	/* DSR1 */
+	if (pins & ATMEL_UART_RTS)
 		at91_set_A_periph(AT91_PIN_PB26, 0);	/* RTS1 */
 }
 
@@ -973,10 +984,15 @@ static struct platform_device at91rm9200_uart2_device = {
 	.num_resources	= ARRAY_SIZE(uart2_resources),
 };
 
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PA22, 0);		/* RXD2 */
 	at91_set_A_periph(AT91_PIN_PA23, 1);		/* TXD2 */
+
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PA30, 0);	/* CTS2 */
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PA31, 0);	/* RTS2 */
 }
 
 static struct resource uart3_resources[] = {
@@ -1011,16 +1027,21 @@ static struct platform_device at91rm9200_uart3_device = {
 	.num_resources	= ARRAY_SIZE(uart3_resources),
 };
 
-static inline void configure_usart3_pins(void)
+static inline void configure_usart3_pins(unsigned pins)
 {
 	at91_set_B_periph(AT91_PIN_PA5, 1);		/* TXD3 */
 	at91_set_B_periph(AT91_PIN_PA6, 0);		/* RXD3 */
+
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PB1, 0);	/* CTS3 */
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PB0, 0);	/* RTS3 */
 }
 
 static struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
 struct platform_device *atmel_default_console_device;	/* the serial console device */
 
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
 {
 	int i;
 
@@ -1028,22 +1049,22 @@ void __init at91_init_serial(struct at91_uart_config *config)
 	for (i = 0; i < config->nr_tty; i++) {
 		switch (config->tty_map[i]) {
 			case 0:
-				configure_usart0_pins();
+				configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
 				at91_uarts[i] = &at91rm9200_uart0_device;
 				at91_clock_associate("usart0_clk", &at91rm9200_uart0_device.dev, "usart");
 				break;
 			case 1:
-				configure_usart1_pins();
+				configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
 				at91_uarts[i] = &at91rm9200_uart1_device;
 				at91_clock_associate("usart1_clk", &at91rm9200_uart1_device.dev, "usart");
 				break;
 			case 2:
-				configure_usart2_pins();
+				configure_usart2_pins(0);
 				at91_uarts[i] = &at91rm9200_uart2_device;
 				at91_clock_associate("usart2_clk", &at91rm9200_uart2_device.dev, "usart");
 				break;
 			case 3:
-				configure_usart3_pins();
+				configure_usart3_pins(0);
 				at91_uarts[i] = &at91rm9200_uart3_device;
 				at91_clock_associate("usart3_clk", &at91rm9200_uart3_device.dev, "usart");
 				break;
@@ -1065,6 +1086,53 @@ void __init at91_init_serial(struct at91_uart_config *config)
 		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+	struct platform_device *pdev;
+
+	switch (id) {
+		case 0:		/* DBGU */
+			pdev = &at91rm9200_dbgu_device;
+			configure_dbgu_pins();
+			at91_clock_associate("mck", &pdev->dev, "usart");
+			break;
+		case AT91RM9200_ID_US0:
+			pdev = &at91rm9200_uart0_device;
+			configure_usart0_pins(pins);
+			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+			break;
+		case AT91RM9200_ID_US1:
+			pdev = &at91rm9200_uart1_device;
+			configure_usart1_pins(pins);
+			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+			break;
+		case AT91RM9200_ID_US2:
+			pdev = &at91rm9200_uart2_device;
+			configure_usart2_pins(pins);
+			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+			break;
+		case AT91RM9200_ID_US3:
+			pdev = &at91rm9200_uart3_device;
+			configure_usart3_pins(pins);
+			at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+			break;
+		default:
+			return;
+	}
+	pdev->id = portnr;		/* update to mapped ID */
+
+	if (portnr < ATMEL_MAX_UART)
+		at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+	if (portnr < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[portnr];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1075,7 +1143,9 @@ void __init at91_add_device_serial(void)
 	}
 }
 #else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

arch/arm/mach-at91/at91sam9260_devices.c

@@ -760,15 +760,22 @@ static struct platform_device at91sam9260_uart0_device = {
 	.num_resources	= ARRAY_SIZE(uart0_resources),
 };
 
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PB4, 1);		/* TXD0 */
 	at91_set_A_periph(AT91_PIN_PB5, 0);		/* RXD0 */
+
+	if (pins & ATMEL_UART_RTS)
 		at91_set_A_periph(AT91_PIN_PB26, 0);	/* RTS0 */
+	if (pins & ATMEL_UART_CTS)
 		at91_set_A_periph(AT91_PIN_PB27, 0);	/* CTS0 */
+	if (pins & ATMEL_UART_DTR)
 		at91_set_A_periph(AT91_PIN_PB24, 0);	/* DTR0 */
+	if (pins & ATMEL_UART_DSR)
 		at91_set_A_periph(AT91_PIN_PB22, 0);	/* DSR0 */
+	if (pins & ATMEL_UART_DCD)
 		at91_set_A_periph(AT91_PIN_PB23, 0);	/* DCD0 */
+	if (pins & ATMEL_UART_RI)
 		at91_set_A_periph(AT91_PIN_PB25, 0);	/* RI0 */
 }
 
@@ -804,11 +811,14 @@ static struct platform_device at91sam9260_uart1_device = {
 	.num_resources	= ARRAY_SIZE(uart1_resources),
 };
 
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PB6, 1);		/* TXD1 */
 	at91_set_A_periph(AT91_PIN_PB7, 0);		/* RXD1 */
+
+	if (pins & ATMEL_UART_RTS)
 		at91_set_A_periph(AT91_PIN_PB28, 0);	/* RTS1 */
+	if (pins & ATMEL_UART_CTS)
 		at91_set_A_periph(AT91_PIN_PB29, 0);	/* CTS1 */
 }
 
@@ -844,10 +854,15 @@ static struct platform_device at91sam9260_uart2_device = {
 	.num_resources	= ARRAY_SIZE(uart2_resources),
 };
 
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PB8, 1);		/* TXD2 */
 	at91_set_A_periph(AT91_PIN_PB9, 0);		/* RXD2 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_A_periph(AT91_PIN_PA4, 0);	/* RTS2 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_A_periph(AT91_PIN_PA5, 0);	/* CTS2 */
 }
 
 static struct resource uart3_resources[] = {
@@ -882,10 +897,15 @@ static struct platform_device at91sam9260_uart3_device = {
 	.num_resources	= ARRAY_SIZE(uart3_resources),
 };
 
-static inline void configure_usart3_pins(void)
+static inline void configure_usart3_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PB10, 1);		/* TXD3 */
 	at91_set_A_periph(AT91_PIN_PB11, 0);		/* RXD3 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PC8, 0);	/* RTS3 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PC10, 0);	/* CTS3 */
 }
 
 static struct resource uart4_resources[] = {
@@ -967,7 +987,7 @@ static inline void configure_usart5_pins(void)
 static struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
 struct platform_device *atmel_default_console_device;	/* the serial console device */
 
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
 {
 	int i;
 
@@ -975,22 +995,22 @@ void __init at91_init_serial(struct at91_uart_config *config)
 	for (i = 0; i < config->nr_tty; i++) {
 		switch (config->tty_map[i]) {
 			case 0:
-				configure_usart0_pins();
+				configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DSR | ATMEL_UART_DTR | ATMEL_UART_DCD | ATMEL_UART_RI);
 				at91_uarts[i] = &at91sam9260_uart0_device;
 				at91_clock_associate("usart0_clk", &at91sam9260_uart0_device.dev, "usart");
 				break;
 			case 1:
-				configure_usart1_pins();
+				configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
 				at91_uarts[i] = &at91sam9260_uart1_device;
 				at91_clock_associate("usart1_clk", &at91sam9260_uart1_device.dev, "usart");
 				break;
 			case 2:
-				configure_usart2_pins();
+				configure_usart2_pins(0);
 				at91_uarts[i] = &at91sam9260_uart2_device;
 				at91_clock_associate("usart2_clk", &at91sam9260_uart2_device.dev, "usart");
 				break;
 			case 3:
-				configure_usart3_pins();
+				configure_usart3_pins(0);
 				at91_uarts[i] = &at91sam9260_uart3_device;
 				at91_clock_associate("usart3_clk", &at91sam9260_uart3_device.dev, "usart");
 				break;
@@ -1022,6 +1042,63 @@ void __init at91_init_serial(struct at91_uart_config *config)
 		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+	struct platform_device *pdev;
+
+	switch (id) {
+		case 0:		/* DBGU */
+			pdev = &at91sam9260_dbgu_device;
+			configure_dbgu_pins();
+			at91_clock_associate("mck", &pdev->dev, "usart");
+			break;
+		case AT91SAM9260_ID_US0:
+			pdev = &at91sam9260_uart0_device;
+			configure_usart0_pins(pins);
+			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9260_ID_US1:
+			pdev = &at91sam9260_uart1_device;
+			configure_usart1_pins(pins);
+			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9260_ID_US2:
+			pdev = &at91sam9260_uart2_device;
+			configure_usart2_pins(pins);
+			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9260_ID_US3:
+			pdev = &at91sam9260_uart3_device;
+			configure_usart3_pins(pins);
+			at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9260_ID_US4:
+			pdev = &at91sam9260_uart4_device;
+			configure_usart4_pins();
+			at91_clock_associate("usart4_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9260_ID_US5:
+			pdev = &at91sam9260_uart5_device;
+			configure_usart5_pins();
+			at91_clock_associate("usart5_clk", &pdev->dev, "usart");
+			break;
+		default:
+			return;
+	}
+	pdev->id = portnr;		/* update to mapped ID */
+
+	if (portnr < ATMEL_MAX_UART)
+		at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+	if (portnr < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[portnr];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1032,7 +1109,9 @@ void __init at91_add_device_serial(void)
 	}
 }
 #else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

arch/arm/mach-at91/at91sam9261_devices.c

@@ -867,11 +867,14 @@ static struct platform_device at91sam9261_uart0_device = {
 	.num_resources	= ARRAY_SIZE(uart0_resources),
 };
 
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PC8, 1);		/* TXD0 */
 	at91_set_A_periph(AT91_PIN_PC9, 0);		/* RXD0 */
+
+	if (pins & ATMEL_UART_RTS)
 		at91_set_A_periph(AT91_PIN_PC10, 0);	/* RTS0 */
+	if (pins & ATMEL_UART_CTS)
 		at91_set_A_periph(AT91_PIN_PC11, 0);	/* CTS0 */
 }
 
@@ -907,10 +910,15 @@ static struct platform_device at91sam9261_uart1_device = {
 	.num_resources	= ARRAY_SIZE(uart1_resources),
 };
 
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PC12, 1);		/* TXD1 */
 	at91_set_A_periph(AT91_PIN_PC13, 0);		/* RXD1 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PA12, 0);	/* RTS1 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PA13, 0);	/* CTS1 */
 }
 
 static struct resource uart2_resources[] = {
@@ -945,16 +953,21 @@ static struct platform_device at91sam9261_uart2_device = {
 	.num_resources	= ARRAY_SIZE(uart2_resources),
 };
 
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PC15, 0);		/* RXD2 */
 	at91_set_A_periph(AT91_PIN_PC14, 1);		/* TXD2 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PA15, 0);	/* RTS2*/
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PA16, 0);	/* CTS2 */
 }
 
 static struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
 struct platform_device *atmel_default_console_device;	/* the serial console device */
 
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
 {
 	int i;
 
@@ -962,17 +975,17 @@ void __init at91_init_serial(struct at91_uart_config *config)
 	for (i = 0; i < config->nr_tty; i++) {
 		switch (config->tty_map[i]) {
 			case 0:
-				configure_usart0_pins();
+				configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
 				at91_uarts[i] = &at91sam9261_uart0_device;
 				at91_clock_associate("usart0_clk", &at91sam9261_uart0_device.dev, "usart");
 				break;
 			case 1:
-				configure_usart1_pins();
+				configure_usart1_pins(0);
 				at91_uarts[i] = &at91sam9261_uart1_device;
 				at91_clock_associate("usart1_clk", &at91sam9261_uart1_device.dev, "usart");
 				break;
 			case 2:
-				configure_usart2_pins();
+				configure_usart2_pins(0);
 				at91_uarts[i] = &at91sam9261_uart2_device;
 				at91_clock_associate("usart2_clk", &at91sam9261_uart2_device.dev, "usart");
 				break;
@@ -994,6 +1007,48 @@ void __init at91_init_serial(struct at91_uart_config *config)
 		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+	struct platform_device *pdev;
+
+	switch (id) {
+		case 0:		/* DBGU */
+			pdev = &at91sam9261_dbgu_device;
+			configure_dbgu_pins();
+			at91_clock_associate("mck", &pdev->dev, "usart");
+			break;
+		case AT91SAM9261_ID_US0:
+			pdev = &at91sam9261_uart0_device;
+			configure_usart0_pins(pins);
+			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9261_ID_US1:
+			pdev = &at91sam9261_uart1_device;
+			configure_usart1_pins(pins);
+			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9261_ID_US2:
+			pdev = &at91sam9261_uart2_device;
+			configure_usart2_pins(pins);
+			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+			break;
+		default:
+			return;
+	}
+	pdev->id = portnr;		/* update to mapped ID */
+
+	if (portnr < ATMEL_MAX_UART)
+		at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+	if (portnr < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[portnr];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1004,7 +1059,9 @@ void __init at91_add_device_serial(void)
 	}
 }
 #else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

arch/arm/mach-at91/at91sam9263_devices.c

@@ -1071,11 +1071,14 @@ static struct platform_device at91sam9263_uart0_device = {
 	.num_resources	= ARRAY_SIZE(uart0_resources),
 };
 
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PA26, 1);		/* TXD0 */
 	at91_set_A_periph(AT91_PIN_PA27, 0);		/* RXD0 */
+
+	if (pins & ATMEL_UART_RTS)
 		at91_set_A_periph(AT91_PIN_PA28, 0);	/* RTS0 */
+	if (pins & ATMEL_UART_CTS)
 		at91_set_A_periph(AT91_PIN_PA29, 0);	/* CTS0 */
 }
 
@@ -1111,11 +1114,14 @@ static struct platform_device at91sam9263_uart1_device = {
 	.num_resources	= ARRAY_SIZE(uart1_resources),
 };
 
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PD0, 1);		/* TXD1 */
 	at91_set_A_periph(AT91_PIN_PD1, 0);		/* RXD1 */
+
+	if (pins & ATMEL_UART_RTS)
 		at91_set_B_periph(AT91_PIN_PD7, 0);	/* RTS1 */
+	if (pins & ATMEL_UART_CTS)
 		at91_set_B_periph(AT91_PIN_PD8, 0);	/* CTS1 */
 }
 
@@ -1151,18 +1157,21 @@ static struct platform_device at91sam9263_uart2_device = {
 	.num_resources	= ARRAY_SIZE(uart2_resources),
 };
 
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PD2, 1);		/* TXD2 */
 	at91_set_A_periph(AT91_PIN_PD3, 0);		/* RXD2 */
+
+	if (pins & ATMEL_UART_RTS)
 		at91_set_B_periph(AT91_PIN_PD5, 0);	/* RTS2 */
+	if (pins & ATMEL_UART_CTS)
 		at91_set_B_periph(AT91_PIN_PD6, 0);	/* CTS2 */
 }
 
 static struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
 struct platform_device *atmel_default_console_device;	/* the serial console device */
 
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
 {
 	int i;
 
@@ -1170,17 +1179,17 @@ void __init at91_init_serial(struct at91_uart_config *config)
 	for (i = 0; i < config->nr_tty; i++) {
 		switch (config->tty_map[i]) {
 			case 0:
-				configure_usart0_pins();
+				configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
 				at91_uarts[i] = &at91sam9263_uart0_device;
 				at91_clock_associate("usart0_clk", &at91sam9263_uart0_device.dev, "usart");
 				break;
 			case 1:
-				configure_usart1_pins();
+				configure_usart1_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
 				at91_uarts[i] = &at91sam9263_uart1_device;
 				at91_clock_associate("usart1_clk", &at91sam9263_uart1_device.dev, "usart");
 				break;
 			case 2:
-				configure_usart2_pins();
+				configure_usart2_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
 				at91_uarts[i] = &at91sam9263_uart2_device;
 				at91_clock_associate("usart2_clk", &at91sam9263_uart2_device.dev, "usart");
 				break;
@@ -1202,6 +1211,48 @@ void __init at91_init_serial(struct at91_uart_config *config)
 		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+	struct platform_device *pdev;
+
+	switch (id) {
+		case 0:		/* DBGU */
+			pdev = &at91sam9263_dbgu_device;
+			configure_dbgu_pins();
+			at91_clock_associate("mck", &pdev->dev, "usart");
+			break;
+		case AT91SAM9263_ID_US0:
+			pdev = &at91sam9263_uart0_device;
+			configure_usart0_pins(pins);
+			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9263_ID_US1:
+			pdev = &at91sam9263_uart1_device;
+			configure_usart1_pins(pins);
+			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9263_ID_US2:
+			pdev = &at91sam9263_uart2_device;
+			configure_usart2_pins(pins);
+			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+			break;
+		default:
+			return;
+	}
+	pdev->id = portnr;		/* update to mapped ID */
+
+	if (portnr < ATMEL_MAX_UART)
+		at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+	if (portnr < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[portnr];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -1213,6 +1264,8 @@ void __init at91_add_device_serial(void)
 }
 #else
 void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -676,12 +676,23 @@ static struct platform_device at91sam9rl_uart0_device = {
 	.num_resources	= ARRAY_SIZE(uart0_resources),
 };
 
-static inline void configure_usart0_pins(void)
+static inline void configure_usart0_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PA6, 1);		/* TXD0 */
 	at91_set_A_periph(AT91_PIN_PA7, 0);		/* RXD0 */
+
+	if (pins & ATMEL_UART_RTS)
 		at91_set_A_periph(AT91_PIN_PA9, 0);	/* RTS0 */
+	if (pins & ATMEL_UART_CTS)
 		at91_set_A_periph(AT91_PIN_PA10, 0);	/* CTS0 */
+	if (pins & ATMEL_UART_DSR)
+		at91_set_A_periph(AT91_PIN_PD14, 0);	/* DSR0 */
+	if (pins & ATMEL_UART_DTR)
+		at91_set_A_periph(AT91_PIN_PD15, 0);	/* DTR0 */
+	if (pins & ATMEL_UART_DCD)
+		at91_set_A_periph(AT91_PIN_PD16, 0);	/* DCD0 */
+	if (pins & ATMEL_UART_RI)
+		at91_set_A_periph(AT91_PIN_PD17, 0);	/* RI0 */
 }
 
 static struct resource uart1_resources[] = {
@@ -716,10 +727,15 @@ static struct platform_device at91sam9rl_uart1_device = {
 	.num_resources	= ARRAY_SIZE(uart1_resources),
 };
 
-static inline void configure_usart1_pins(void)
+static inline void configure_usart1_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PA11, 1);		/* TXD1 */
 	at91_set_A_periph(AT91_PIN_PA12, 0);		/* RXD1 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PA18, 0);	/* RTS1 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PA19, 0);	/* CTS1 */
 }
 
 static struct resource uart2_resources[] = {
@@ -754,10 +770,15 @@ static struct platform_device at91sam9rl_uart2_device = {
 	.num_resources	= ARRAY_SIZE(uart2_resources),
 };
 
-static inline void configure_usart2_pins(void)
+static inline void configure_usart2_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PA13, 1);		/* TXD2 */
 	at91_set_A_periph(AT91_PIN_PA14, 0);		/* RXD2 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_A_periph(AT91_PIN_PA29, 0);	/* RTS2 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_A_periph(AT91_PIN_PA30, 0);	/* CTS2 */
 }
 
 static struct resource uart3_resources[] = {
@@ -792,16 +813,21 @@ static struct platform_device at91sam9rl_uart3_device = {
 	.num_resources	= ARRAY_SIZE(uart3_resources),
 };
 
-static inline void configure_usart3_pins(void)
+static inline void configure_usart3_pins(unsigned pins)
 {
 	at91_set_A_periph(AT91_PIN_PB0, 1);		/* TXD3 */
 	at91_set_A_periph(AT91_PIN_PB1, 0);		/* RXD3 */
+
+	if (pins & ATMEL_UART_RTS)
+		at91_set_B_periph(AT91_PIN_PD4, 0);	/* RTS3 */
+	if (pins & ATMEL_UART_CTS)
+		at91_set_B_periph(AT91_PIN_PD3, 0);	/* CTS3 */
 }
 
 static struct platform_device *at91_uarts[ATMEL_MAX_UART];	/* the UARTs to use */
 struct platform_device *atmel_default_console_device;	/* the serial console device */
 
-void __init at91_init_serial(struct at91_uart_config *config)
+void __init __deprecated at91_init_serial(struct at91_uart_config *config)
 {
 	int i;
 
@@ -809,22 +835,22 @@ void __init at91_init_serial(struct at91_uart_config *config)
 	for (i = 0; i < config->nr_tty; i++) {
 		switch (config->tty_map[i]) {
 			case 0:
-				configure_usart0_pins();
+				configure_usart0_pins(ATMEL_UART_CTS | ATMEL_UART_RTS);
 				at91_uarts[i] = &at91sam9rl_uart0_device;
 				at91_clock_associate("usart0_clk", &at91sam9rl_uart0_device.dev, "usart");
 				break;
 			case 1:
-				configure_usart1_pins();
+				configure_usart1_pins(0);
 				at91_uarts[i] = &at91sam9rl_uart1_device;
 				at91_clock_associate("usart1_clk", &at91sam9rl_uart1_device.dev, "usart");
 				break;
 			case 2:
-				configure_usart2_pins();
+				configure_usart2_pins(0);
 				at91_uarts[i] = &at91sam9rl_uart2_device;
 				at91_clock_associate("usart2_clk", &at91sam9rl_uart2_device.dev, "usart");
 				break;
 			case 3:
-				configure_usart3_pins();
+				configure_usart3_pins(0);
 				at91_uarts[i] = &at91sam9rl_uart3_device;
 				at91_clock_associate("usart3_clk", &at91sam9rl_uart3_device.dev, "usart");
 				break;
@@ -846,6 +872,53 @@ void __init at91_init_serial(struct at91_uart_config *config)
 		printk(KERN_INFO "AT91: No default serial console defined.\n");
 }
 
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
+{
+	struct platform_device *pdev;
+
+	switch (id) {
+		case 0:		/* DBGU */
+			pdev = &at91sam9rl_dbgu_device;
+			configure_dbgu_pins();
+			at91_clock_associate("mck", &pdev->dev, "usart");
+			break;
+		case AT91SAM9RL_ID_US0:
+			pdev = &at91sam9rl_uart0_device;
+			configure_usart0_pins(pins);
+			at91_clock_associate("usart0_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9RL_ID_US1:
+			pdev = &at91sam9rl_uart1_device;
+			configure_usart1_pins(pins);
+			at91_clock_associate("usart1_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9RL_ID_US2:
+			pdev = &at91sam9rl_uart2_device;
+			configure_usart2_pins(pins);
+			at91_clock_associate("usart2_clk", &pdev->dev, "usart");
+			break;
+		case AT91SAM9RL_ID_US3:
+			pdev = &at91sam9rl_uart3_device;
+			configure_usart3_pins(pins);
+			at91_clock_associate("usart3_clk", &pdev->dev, "usart");
+			break;
+		default:
+			return;
+	}
+	pdev->id = portnr;		/* update to mapped ID */
+
+	if (portnr < ATMEL_MAX_UART)
+		at91_uarts[portnr] = pdev;
+}
+
+void __init at91_set_serial_console(unsigned portnr)
+{
+	if (portnr < ATMEL_MAX_UART)
+		atmel_default_console_device = at91_uarts[portnr];
+	if (!atmel_default_console_device)
+		printk(KERN_INFO "AT91: No default serial console defined.\n");
+}
+
 void __init at91_add_device_serial(void)
 {
 	int i;
@@ -856,7 +929,9 @@ void __init at91_add_device_serial(void)
 	}
 }
 #else
-void __init at91_init_serial(struct at91_uart_config *config) {}
+void __init __deprecated at91_init_serial(struct at91_uart_config *config) {}
+void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
+void __init at91_set_serial_console(unsigned portnr) {}
 void __init at91_add_device_serial(void) {}
 #endif
 

include/asm-arm/arch-at91/board.h

@@ -101,13 +101,23 @@ extern void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_de
 extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
 
  /* Serial */
+#define ATMEL_UART_CTS	0x01
+#define ATMEL_UART_RTS	0x02
+#define ATMEL_UART_DSR	0x04
+#define ATMEL_UART_DTR	0x08
+#define ATMEL_UART_DCD	0x10
+#define ATMEL_UART_RI	0x20
+
+extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
+extern void __init at91_set_serial_console(unsigned portnr);
+
 struct at91_uart_config {
 	unsigned short	console_tty;	/* tty number of serial console */
 	unsigned short	nr_tty;		/* number of serial tty's */
 	short		tty_map[];	/* map UART to tty number */
 };
 extern struct platform_device *atmel_default_console_device;
-extern void __init at91_init_serial(struct at91_uart_config *config);
+extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
 
 struct atmel_uart_data {
 	short		use_dma_tx;	/* use transmit DMA? */