Merge tag 'sunxi-dt64-for-4.17' of...

Merge tag 'sunxi-dt64-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Pull "Allwinner arm64 DT changes for 4.17" from Maxime Ripard:

We've had for this release a pretty good progress on the arm64 front as
well:
  - The A64 now has SPDIF support
  - The H6 is now supported (even though at an early stage)
  - The TERES-I laptop from Olimex has seen some early support as well

* tag 'sunxi-dt64-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  arm64: dts: allwinner: a64: Add support for TERES-I laptop
  arm64: dts: allwinner: a64: add simplefb for A64 SoC
  arm64: dts: allwinner: a64: Add watchdog
  arm64: dts: allwinner: a64: Add i2c0 pins
  arm64: allwinner: h6: add support for Pine H64 board
  arm64: allwinner: h6: add the basical Allwinner H6 DTSI file
  arm64: dts: sunxi: Switch MMC nodes away from cd-inverted property
  arm64: dts: allwinner: a64: Add DAI nodes
  arm64: dts: allwinner: a64: Add SPDIF to the Pine64
  arm64: dts: allwinner: a64: Add SPDIF to the A64
  arm64: dts: allwinner: a64: Add the SPDIF block and pin

Documentation/devicetree/bindings/watchdog/sunxi-wdt.txt

@@ -2,8 +2,10 @@ Allwinner SoCs Watchdog timer
 
 Required properties:
 
-- compatible : should be either "allwinner,sun4i-a10-wdt" or
-               "allwinner,sun6i-a31-wdt"
+- compatible : should be one of
+	"allwinner,sun4i-a10-wdt"
+	"allwinner,sun6i-a31-wdt"
+	"allwinner,sun50i-a64-wdt","allwinner,sun6i-a31-wdt"
 - reg : Specifies base physical address and size of the registers.
 
 Example:

arch/arm64/boot/dts/allwinner/Makefile

@@ -5,8 +5,10 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-olinuxino.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo2.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-nanopi-neo-plus2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb

arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts

@@ -120,8 +120,7 @@ &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";

arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts

@@ -82,8 +82,7 @@ &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";

arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts

@@ -68,8 +68,7 @@ &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";

arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts

@@ -67,8 +67,7 @@ &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 

arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts

@@ -103,8 +103,7 @@ &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";
@@ -230,6 +229,11 @@ &reg_rtc_ldo {
 	regulator-name = "vcc-rtc";
 };
 
+/* On Euler connector */
+&spdif {
+	status = "disabled";
+};
+
 /* On Exp and Euler connectors */
 &uart0 {
 	pinctrl-names = "default";

arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts

+/*
+ * Copyright (C) Harald Geyer <harald@ccbib.org>
+ * based on sun50i-a64-olinuxino.dts by Jagan Teki <jteki@openedev.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0 OR MIT)
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Olimex A64 Teres-I";
+	compatible = "olimex,a64-teres-i", "allwinner,sun50i-a64";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+
+		framebuffer-lcd {
+			eDP25-supply = <&reg_dldo2>;
+			eDP12-supply = <&reg_dldo3>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		lid-switch {
+			label = "Lid Switch";
+			gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		capslock {
+			label = "teres-i:green:capslock";
+			gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */
+		};
+
+		numlock {
+			label = "teres-i:green:numlock";
+			gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */
+		};
+	};
+
+	reg_usb1_vbus: usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
+		status = "okay";
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+
+/* The ANX6345 eDP-bridge is on i2c0. There is no linux (mainline)
+ * driver for this chip at the moment, the bootloader initializes it.
+ * However it can be accessed with the i2c-dev driver from user space.
+ */
+&i2c0 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_aldo2>;
+	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723bs: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-source;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "vcc-pe";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-ddr3";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vcc-pd";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "eDP12";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-dvdd-csi";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};

arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi

@@ -52,6 +52,26 @@ / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+/*
+ * The pipeline mixer0-lcd0 depends on clock CLK_MIXER0 from DE2 CCU.
+ * However there is no support for this clock on A64 yet, so we depend
+ * on the upstream clocks here to keep them (and thus CLK_MIXER0) up.
+ */
+		simplefb_lcd: framebuffer-lcd {
+			compatible = "allwinner,simple-framebuffer",
+				     "simple-framebuffer";
+			allwinner,pipeline = "mixer0-lcd0";
+			clocks = <&ccu CLK_TCON0>,
+				 <&ccu CLK_DE>, <&ccu CLK_BUS_DE>;
+			status = "disabled";
+		};
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -112,6 +132,24 @@ psci {
 		method = "smc";
 	};
 
+	sound_spdif {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "On-board SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13
@@ -291,6 +329,11 @@ pio: pinctrl@1c20800 {
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
+			i2c0_pins: i2c0_pins {
+				pins = "PH0", "PH1";
+				function = "i2c0";
+			};
+
 			i2c1_pins: i2c1_pins {
 				pins = "PH2", "PH3";
 				function = "i2c1";
@@ -336,6 +379,11 @@ rgmii_pins: rgmii_pins {
 				drive-strength = <40>;
 			};
 
+			spdif_tx_pin: spdif {
+				pins = "PH8";
+				function = "spdif";
+			};
+
 			spi0_pins: spi0 {
 				pins = "PC0", "PC1", "PC2", "PC3";
 				function = "spi0";
@@ -382,6 +430,50 @@ uart4_rts_cts_pins: uart4-rts-cts-pins {
 			};
 		};
 
+		spdif: spdif@1c21000 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun50i-a64-spdif",
+				     "allwinner,sun8i-h3-spdif";
+			reg = <0x01c21000 0x400>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+			resets = <&ccu RST_BUS_SPDIF>;
+			clock-names = "apb", "spdif";
+			dmas = <&dma 2>;
+			dma-names = "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spdif_tx_pin>;
+			status = "disabled";
+		};
+
+		i2s0: i2s@1c22000 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun50i-a64-i2s",
+				     "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22000 0x400>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S0>;
+			dma-names = "rx", "tx";
+			dmas = <&dma 3>, <&dma 3>;
+			status = "disabled";
+		};
+
+		i2s1: i2s@1c22400 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun50i-a64-i2s",
+				     "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22400 0x400>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S1>;
+			dma-names = "rx", "tx";
+			dmas = <&dma 4>, <&dma 4>;
+			status = "disabled";
+		};
+
 		uart0: serial@1c28000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
@@ -593,5 +685,12 @@ r_rsb: rsb@1f03400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
+
+		wdt0: watchdog@1c20ca0 {
+			compatible = "allwinner,sun50i-a64-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 };

arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts

+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Pine H64";
+	compatible = "pine64,pine-h64", "allwinner,sun50i-h6";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};

arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <2>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <3>;
+			enable-method = "psci";
+		};
+	};
+
+	iosc: internal-osc-clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <16000000>;
+		clock-accuracy = <300000000>;
+		clock-output-names = "iosc";
+	};
+
+	osc24M: osc24M_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "osc24M";
+	};
+
+	osc32k: osc32k_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "osc32k";
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ccu: clock@3001000 {
+			compatible = "allwinner,sun50i-h6-ccu";
+			reg = <0x03001000 0x1000>;
+			clocks = <&osc24M>, <&osc32k>, <&iosc>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		gic: interrupt-controller@3021000 {
+			compatible = "arm,gic-400";
+			reg = <0x03021000 0x1000>,
+			      <0x03022000 0x2000>,
+			      <0x03024000 0x2000>,
+			      <0x03026000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		pio: pinctrl@300b000 {
+			compatible = "allwinner,sun50i-h6-pinctrl";
+			reg = <0x0300b000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu 26>, <&osc24M>, <&osc32k>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			uart0_ph_pins: uart0-ph {
+				pins = "PH0", "PH1";
+				function = "uart0";
+			};
+		};
+
+		uart0: serial@5000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu 70>;
+			resets = <&ccu 21>;
+			status = "disabled";
+		};
+
+		uart1: serial@5000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu 71>;
+			resets = <&ccu 22>;
+			status = "disabled";
+		};
+
+		uart2: serial@5000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu 72>;
+			resets = <&ccu 23>;
+			status = "disabled";
+		};
+
+		uart3: serial@5000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu 73>;
+			resets = <&ccu 24>;
+			status = "disabled";
+		};
+	};
+};