arm64: dts: qcom: sc8280xp: Add reference device

Add basic support for the SC8280XP reference device, which allows it to
boot to a shell (using EFIFB) with functional storage (UFS), USB,
keyboard, touchpad, touchscreen, backlight and remoteprocs.

The PMICs are, per socinfo, reused from other platforms. But given that
the address of the PMICs doesn't match other cases and that it's
desirable to label things according to the schematics a new dtsi file is
created to represent the reference combination of PMICs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220629041438.1352536-5-bjorn.andersson@linaro.org

arch/arm64/boot/dts/qcom/Makefile

@@ -86,6 +86,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-villager-r0.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-crd-r3.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc8280xp-crd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sda660-inforce-ifc6560.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb

arch/arm64/boot/dts/qcom/sc8280xp-crd.dts

+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc8280xp.dtsi"
+#include "sc8280xp-pmics.dtsi"
+
+/ {
+	model = "Qualcomm SC8280XP CRD";
+	compatible = "qcom,sc8280xp-crd", "qcom,sc8280xp";
+
+	aliases {
+		serial0 = &qup2_uart17;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pmc8280c_lpg 3 1000000>;
+		enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
+		power-supply = <&vreg_edp_bl>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vreg_edp_bl: regulator-edp-bl {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_BL";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		gpio = <&pmc8280_1_gpios 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_reg_en>;
+
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8280_1_gpios 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&misc_3p3_reg_en>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&apps_rsc {
+	pmc8280-1-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-l3-l5-supply = <&vreg_s11b>;
+
+		vreg_s11b: smps11 {
+			regulator-name = "vreg_s11b";
+			regulator-min-microvolt = <1272000>;
+			regulator-max-microvolt = <1272000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3b: ldo3 {
+			regulator-name = "vreg_l3b";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vreg_l4b: ldo4 {
+			regulator-name = "vreg_l4b";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6b: ldo6 {
+			regulator-name = "vreg_l6b";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+	};
+
+	pmc8280c-rpmh-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-name = "vreg_l7c";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l13c: ldo13 {
+			regulator-name = "vreg_l13c";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+	};
+
+	pmc8280-2-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-l4-supply = <&vreg_s11b>;
+
+		vreg_l3d: ldo3 {
+			regulator-name = "vreg_l3d";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4d: ldo4 {
+			regulator-name = "vreg_l4d";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6d: ldo6 {
+			regulator-name = "vreg_l6d";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7d: ldo7 {
+			regulator-name = "vreg_l7d";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l9d: ldo9 {
+			regulator-name = "vreg_l9d";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+	};
+};
+
+&pmc8280c_lpg {
+	status = "okay";
+};
+
+&pmk8280_pon_pwrkey {
+	status = "okay";
+};
+
+&qup0 {
+	status = "okay";
+};
+
+&qup0_i2c4 {
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&qup0_i2c4_default>, <&ts0_default>;
+
+	status = "okay";
+
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+	};
+};
+
+&qup1 {
+	status = "okay";
+};
+
+&qup2 {
+	status = "okay";
+};
+
+&qup2_i2c5 {
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&qup2_i2c5_default>, <&kybd_default>, <&tpad_default>;
+
+	status = "okay";
+
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+	};
+
+	keyboard@68 {
+		compatible = "hid-over-i2c";
+		reg = <0x68>;
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+	};
+};
+
+&qup2_uart17 {
+	compatible = "qcom,geni-debug-uart";
+
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sc8280xp/qcadsp8280.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_nsp0 {
+	firmware-name = "qcom/sc8280xp/qccdsp8280.mbn";
+
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7c>;
+	vcc-max-microamp = <800000>;
+	vccq-supply = <&vreg_l3d>;
+	vccq-max-microamp = <900000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l6b>;
+	vdda-pll-supply = <&vreg_l3b>;
+
+	status = "okay";
+};
+
+&usb_0 {
+	status = "okay";
+};
+
+&usb_0_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "host";
+};
+
+&usb_0_hsphy {
+	vdda-pll-supply = <&vreg_l9d>;
+	vdda18-supply = <&vreg_l1c>;
+	vdda33-supply = <&vreg_l7d>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l9d>;
+	vdda-pll-supply = <&vreg_l4d>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vreg_l4b>;
+	vdda18-supply = <&vreg_l1c>;
+	vdda33-supply = <&vreg_l13c>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l4b>;
+	vdda-pll-supply = <&vreg_l3b>;
+
+	status = "okay";
+};
+
+&xo_board_clk {
+	clock-frequency = <38400000>;
+};
+
+/* PINCTRL - additions to nodes defined in sc8280xp.dtsi */
+
+&pmc8280_1_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio8";
+		function = "normal";
+	};
+
+	edp_bl_reg_en: edp-bl-reg-en-state {
+		pins = "gpio9";
+		function = "normal";
+	};
+
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio1";
+		function = "normal";
+	};
+};
+
+&pmc8280c_gpios {
+	edp_bl_pwm: edp-bl-pwm-state {
+		pins = "gpio8";
+		function = "func1";
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
+
+	kybd_default: kybd-default-state {
+		disable {
+			pins = "gpio102";
+			function = "gpio";
+			output-low;
+		};
+
+		int-n {
+			pins = "gpio104";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset {
+			pins = "gpio105";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	qup0_i2c4_default: qup0-i2c4-default-state {
+		pins = "gpio171", "gpio172";
+		function = "qup4";
+
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	qup2_i2c5_default: qup2-i2c5-default-state {
+		pins = "gpio81", "gpio82";
+		function = "qup21";
+
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	tpad_default: tpad-default-state {
+		int-n {
+			pins = "gpio182";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	ts0_default: ts0-default-state {
+		int-n {
+			pins = "gpio175";
+			function = "gpio";
+			bias-pull-up;
+		};
+
+		reset-n {
+			pins = "gpio99";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
+};

arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi

+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmk8280: pmic@0 {
+		compatible = "qcom,pmk8350", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmk8280_pon: pon@1300 {
+			compatible = "qcom,pm8998-pon";
+			reg = <0x1300>;
+
+			pmk8280_pon_pwrkey: pwrkey {
+				compatible = "qcom,pmk8350-pwrkey";
+				interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+				linux,code = <KEY_POWER>;
+				status = "disabled";
+			};
+		};
+	};
+
+	pmc8280_1: pmic@1 {
+		compatible = "qcom,pm8350", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8280_1_gpios: gpio@8800 {
+			compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8280_1_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmc8280c: pmic@2 {
+		compatible = "qcom,pm8350c", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8280c_gpios: gpio@8800 {
+			compatible = "qcom,pm8350c-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8280c_gpios 0 0 9>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pmc8280c_lpg: lpg@e800 {
+			compatible = "qcom,pm8350c-pwm";
+			reg = <0xe800>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+	};
+
+	pmc8280_2: pmic@3 {
+		compatible = "qcom,pm8350", "qcom,spmi-pmic";
+		reg = <0x3 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8280_2_gpios: gpio@8800 {
+			compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8280_2_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmr735a: pmic@4 {
+		compatible = "qcom,pmr735a", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmr735a_gpios: gpio@8800 {
+			compatible = "qcom,pmr735a-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmr735a_gpios 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};