Commit cd400825 authored by Finn Thain's avatar Finn Thain Committed by Martin K. Petersen

ncr5380: Standardize interrupt handling

Because interrupt handling is crucial to the core driver(s), all wrapper
drivers need to agree on this code. This patch removes discrepancies.

NCR5380_intr() in NCR5380.c has the following pointless loop that differs
from the code in atari_NCR5380.c.

	done = 1;
	do {
		/* ... */
	} while (!done);

The 'done' flag gets cleared when a reconnected command is to be processed
from the work queue. But in NCR5380.c, the flag is also used to cause the
interrupt conditions to be re-examined. Perhaps this was because
NCR5380_reselect() was expected to cause another interrupt, or perhaps
the remaining present interrupt conditions need to be handled after the
NCR5380_reselect() call?

Actually, both possibilities are bogus, as is the loop itself. It seems
have been overlooked in the hit-and-miss removal of scsi host instance
list iteration many years ago; see history/history.git commit 491447e1
("[PATCH] next NCR5380 updates") and commit 69e1a948 ("[PATCH] fix up
NCR5380 private data"). See also my earlier patch, "Always retry
arbitration and selection".

The datasheet says, "IRQ can be reset simply by reading the Reset
Parity/Interrupt Register". So don't treat the chip IRQ like a
level-triggered interrupt. Of the conditions that set the IRQ flag,
some are level-triggered and some are edge-triggered, which means IRQ
itself must be edge-triggered.

Some interrupt conditions are latched and some are not. Before clearing
the chip IRQ flag, clear all state that may cause it to be raised. That
means clearing the DMA Mode and Busy Monitor bits in the Mode Register
and clearing the host ID in the Select Enable register.

Also clean up some printk's and some comments. Keep atari_NCR5380.c and
NCR5380.c in agreement.
Signed-off-by: default avatarFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: default avatarHannes Reinecke <hare@suse.com>
Tested-by: default avatarOndrej Zary <linux@rainbow-software.org>
Tested-by: default avatarMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: default avatarMartin K. Petersen <martin.petersen@oracle.com>
parent d1af9c7f
......@@ -959,77 +959,106 @@ static void NCR5380_main(struct work_struct *work)
* from the disconnected queue, and restarting NCR5380_main()
* as required.
*
* Locks: takes the needed instance locks
*/
static irqreturn_t NCR5380_intr(int dummy, void *dev_id)
* The chip can assert IRQ in any of six different conditions. The IRQ flag
* is then cleared by reading the Reset Parity/Interrupt Register (RPIR).
* Three of these six conditions are latched in the Bus and Status Register:
* - End of DMA (cleared by ending DMA Mode)
* - Parity error (cleared by reading RPIR)
* - Loss of BSY (cleared by reading RPIR)
* Two conditions have flag bits that are not latched:
* - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode)
* - Bus reset (non-maskable)
* The remaining condition has no flag bit at all:
* - Selection/reselection
*
* Hence, establishing the cause(s) of any interrupt is partly guesswork.
* In "The DP8490 and DP5380 Comparison Guide", National Semiconductor
* claimed that "the design of the [DP8490] interrupt logic ensures
* interrupts will not be lost (they can be on the DP5380)."
* The L5380/53C80 datasheet from LOGIC Devices has more details.
*
* Checking for bus reset by reading RST is futile because of interrupt
* latency, but a bus reset will reset chip logic. Checking for parity error
* is unnecessary because that interrupt is never enabled. A Loss of BSY
* condition will clear DMA Mode. We can tell when this occurs because the
* the Busy Monitor interrupt is enabled together with DMA Mode.
*/
static irqreturn_t NCR5380_intr(int irq, void *dev_id)
{
struct Scsi_Host *instance = dev_id;
struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *) instance->hostdata;
int done;
struct NCR5380_hostdata *hostdata = shost_priv(instance);
int handled = 0;
unsigned char basr;
unsigned long flags;
dprintk(NDEBUG_INTR, "scsi : NCR5380 irq %d triggered\n",
instance->irq);
do {
done = 1;
spin_lock_irqsave(instance->host_lock, flags);
/* Look for pending interrupts */
basr = NCR5380_read(BUS_AND_STATUS_REG);
/* XXX dispatch to appropriate routine if found and done=0 */
if (basr & BASR_IRQ) {
NCR5380_dprint(NDEBUG_INTR, instance);
if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
done = 0;
dprintk(NDEBUG_INTR, "scsi%d : SEL interrupt\n", instance->host_no);
NCR5380_reselect(instance);
(void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else if (basr & BASR_PARITY_ERROR) {
dprintk(NDEBUG_INTR, "scsi%d : PARITY interrupt\n", instance->host_no);
(void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else if ((NCR5380_read(STATUS_REG) & SR_RST) == SR_RST) {
dprintk(NDEBUG_INTR, "scsi%d : RESET interrupt\n", instance->host_no);
(void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else {
unsigned char mr = NCR5380_read(MODE_REG);
unsigned char sr = NCR5380_read(STATUS_REG);
dprintk(NDEBUG_INTR, "scsi%d: IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n",
instance->host_no, irq, basr, sr, mr);
#if defined(REAL_DMA)
/*
* We should only get PHASE MISMATCH and EOP interrupts
* if we have DMA enabled, so do a sanity check based on
* the current setting of the MODE register.
if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) {
/* Probably End of DMA, Phase Mismatch or Loss of BSY.
* We ack IRQ after clearing Mode Register. Workarounds
* for End of DMA errata need to happen in DMA Mode.
*/
if ((NCR5380_read(MODE_REG) & MR_DMA) && ((basr & BASR_END_DMA_TRANSFER) || !(basr & BASR_PHASE_MATCH))) {
dprintk(NDEBUG_INTR, "scsi%d: interrupt in DMA mode\n", intance->host_no);
int transferred;
if (!hostdata->connected)
panic("scsi%d : received end of DMA interrupt with no connected cmd\n", instance->hostno);
panic("scsi%d : DMA interrupt with no connected cmd\n",
instance->hostno);
transferred = (hostdata->dmalen - NCR5380_dma_residual(instance));
transferred = hostdata->dmalen - NCR5380_dma_residual(instance);
hostdata->connected->SCp.this_residual -= transferred;
hostdata->connected->SCp.ptr += transferred;
hostdata->dmalen = 0;
(void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
/* FIXME: we need to poll briefly then defer a workqueue task ! */
NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG, BASR_ACK, 0, 2*HZ);
NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG, BASR_ACK, 0, 2 * HZ);
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else
#endif /* REAL_DMA */
if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) &&
(sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) {
/* Probably reselected */
NCR5380_write(SELECT_ENABLE_REG, 0);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
dprintk(NDEBUG_INTR, "scsi%d: interrupt with SEL and IO\n",
instance->host_no);
if (!hostdata->connected) {
NCR5380_reselect(instance);
queue_work(hostdata->work_q, &hostdata->main_task);
}
#else
dprintk(NDEBUG_INTR, "scsi : unknown interrupt, BASR 0x%X, MR 0x%X, SR 0x%x\n", basr, NCR5380_read(MODE_REG), NCR5380_read(STATUS_REG));
(void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
#endif
if (!hostdata->connected)
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
} else {
/* Probably Bus Reset */
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
dprintk(NDEBUG_INTR, "scsi%d: unknown interrupt\n", instance->host_no);
}
handled = 1;
} else {
shost_printk(KERN_NOTICE, instance, "interrupt without IRQ bit\n");
}
} /* if BASR_IRQ */
spin_unlock_irqrestore(instance->host_lock, flags);
if(!done)
queue_work(hostdata->work_q, &hostdata->main_task);
} while (!done);
return IRQ_HANDLED;
return IRQ_RETVAL(handled);
}
#endif
......@@ -1218,8 +1247,9 @@ static int NCR5380_select(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
NCR5380_reselect(instance);
printk("scsi%d : reselection after won arbitration?\n", instance->host_no);
if (!hostdata->connected)
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
printk("scsi%d : reselection after won arbitration?\n", instance->host_no);
return -1;
}
......@@ -1563,9 +1593,10 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance, unsigned char *phase
NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
#ifdef REAL_DMA
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_ENABLE_EOP_INTR | MR_MONITOR_BSY);
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
MR_ENABLE_EOP_INTR);
#elif defined(REAL_DMA_POLL)
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE);
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY);
#else
/*
* Note : on my sample board, watch-dog timeouts occurred when interrupts
......@@ -1573,13 +1604,11 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance, unsigned char *phase
* before the setting of DMA mode to after transfer of the last byte.
*/
/* KLL May need eop and parity in 53c400 */
if (hostdata->flags & FLAG_NCR53C400)
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE |
MR_ENABLE_PAR_CHECK | MR_ENABLE_PAR_INTR |
MR_ENABLE_EOP_INTR | MR_MONITOR_BSY);
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
MR_ENABLE_EOP_INTR);
else
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE);
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY);
#endif /* def REAL_DMA */
dprintk(NDEBUG_DMA, "scsi%d : mode reg = 0x%X\n", instance->host_no, NCR5380_read(MODE_REG));
......@@ -1768,16 +1797,7 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance, unsigned char *phase
}
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
if ((!(p & SR_IO)) && (hostdata->flags & FLAG_NCR53C400)) {
dprintk(NDEBUG_C400_PWRITE, "53C400w: Checking for IRQ\n");
if (NCR5380_read(BUS_AND_STATUS_REG) & BASR_IRQ) {
dprintk(NDEBUG_C400_PWRITE, "53C400w: got it, reading reset interrupt reg\n");
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else {
printk("53C400w: IRQ NOT THERE!\n");
}
}
*data = d + c;
*count = 0;
*phase = NCR5380_read(STATUS_REG) & PHASE_MASK;
......@@ -2269,7 +2289,6 @@ static void NCR5380_dma_complete(NCR5380_instance * instance) {
NCR5380_poll_politely(instance, BUS_AND_STATUS_REG, BASR_ACK, 0, 5*HZ);
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
/*
......
......@@ -1144,12 +1144,6 @@ static void NCR5380_dma_complete(struct Scsi_Host *instance)
int saved_data = 0, overrun = 0;
unsigned char p;
if (!hostdata->connected) {
printk(KERN_WARNING "scsi%d: received end of DMA interrupt with "
"no connected cmd\n", HOSTNO);
return;
}
if (hostdata->read_overruns) {
p = hostdata->connected->SCp.phase;
if (p & SR_IO) {
......@@ -1164,10 +1158,6 @@ static void NCR5380_dma_complete(struct Scsi_Host *instance)
}
}
dprintk(NDEBUG_DMA, "scsi%d: real DMA transfer complete, basr 0x%X, sr 0x%X\n",
HOSTNO, NCR5380_read(BUS_AND_STATUS_REG),
NCR5380_read(STATUS_REG));
#if defined(CONFIG_SUN3)
if ((sun3scsi_dma_finish(rq_data_dir(hostdata->connected->request)))) {
pr_err("scsi%d: overrun in UDC counter -- not prepared to deal with this!\n",
......@@ -1186,9 +1176,9 @@ static void NCR5380_dma_complete(struct Scsi_Host *instance)
}
#endif
(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
transferred = hostdata->dma_len - NCR5380_dma_residual(instance);
hostdata->dma_len = 0;
......@@ -1227,83 +1217,97 @@ static void NCR5380_dma_complete(struct Scsi_Host *instance)
* Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses
* from the disconnected queue, and restarting NCR5380_main()
* as required.
*
* The chip can assert IRQ in any of six different conditions. The IRQ flag
* is then cleared by reading the Reset Parity/Interrupt Register (RPIR).
* Three of these six conditions are latched in the Bus and Status Register:
* - End of DMA (cleared by ending DMA Mode)
* - Parity error (cleared by reading RPIR)
* - Loss of BSY (cleared by reading RPIR)
* Two conditions have flag bits that are not latched:
* - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode)
* - Bus reset (non-maskable)
* The remaining condition has no flag bit at all:
* - Selection/reselection
*
* Hence, establishing the cause(s) of any interrupt is partly guesswork.
* In "The DP8490 and DP5380 Comparison Guide", National Semiconductor
* claimed that "the design of the [DP8490] interrupt logic ensures
* interrupts will not be lost (they can be on the DP5380)."
* The L5380/53C80 datasheet from LOGIC Devices has more details.
*
* Checking for bus reset by reading RST is futile because of interrupt
* latency, but a bus reset will reset chip logic. Checking for parity error
* is unnecessary because that interrupt is never enabled. A Loss of BSY
* condition will clear DMA Mode. We can tell when this occurs because the
* the Busy Monitor interrupt is enabled together with DMA Mode.
*/
static irqreturn_t NCR5380_intr(int irq, void *dev_id)
{
struct Scsi_Host *instance = dev_id;
struct NCR5380_hostdata *hostdata = shost_priv(instance);
int done = 1, handled = 0;
int handled = 0;
unsigned char basr;
dprintk(NDEBUG_INTR, "scsi%d: NCR5380 irq triggered\n", HOSTNO);
/* Look for pending interrupts */
basr = NCR5380_read(BUS_AND_STATUS_REG);
dprintk(NDEBUG_INTR, "scsi%d: BASR=%02x\n", HOSTNO, basr);
/* dispatch to appropriate routine if found and done=0 */
if (basr & BASR_IRQ) {
NCR5380_dprint(NDEBUG_INTR, instance);
if ((NCR5380_read(STATUS_REG) & (SR_SEL|SR_IO)) == (SR_SEL|SR_IO)) {
done = 0;
dprintk(NDEBUG_INTR, "scsi%d: SEL interrupt\n", HOSTNO);
NCR5380_reselect(instance);
(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else if (basr & BASR_PARITY_ERROR) {
dprintk(NDEBUG_INTR, "scsi%d: PARITY interrupt\n", HOSTNO);
(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else if ((NCR5380_read(STATUS_REG) & SR_RST) == SR_RST) {
dprintk(NDEBUG_INTR, "scsi%d: RESET interrupt\n", HOSTNO);
(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else {
/*
* The rest of the interrupt conditions can occur only during a
* DMA transfer
*/
unsigned char mr = NCR5380_read(MODE_REG);
unsigned char sr = NCR5380_read(STATUS_REG);
dprintk(NDEBUG_INTR, "scsi%d: IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n",
HOSTNO, irq, basr, sr, mr);
#if defined(REAL_DMA)
/*
* We should only get PHASE MISMATCH and EOP interrupts if we have
* DMA enabled, so do a sanity check based on the current setting
* of the MODE register.
if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) {
/* Probably End of DMA, Phase Mismatch or Loss of BSY.
* We ack IRQ after clearing Mode Register. Workarounds
* for End of DMA errata need to happen in DMA Mode.
*/
if ((NCR5380_read(MODE_REG) & MR_DMA_MODE) &&
((basr & BASR_END_DMA_TRANSFER) ||
!(basr & BASR_PHASE_MATCH))) {
dprintk(NDEBUG_INTR, "scsi%d: interrupt in DMA mode\n", HOSTNO);
dprintk(NDEBUG_INTR, "scsi%d: PHASE MISM or EOP interrupt\n", HOSTNO);
NCR5380_dma_complete( instance );
done = 0;
if (hostdata->connected) {
NCR5380_dma_complete(instance);
queue_work(hostdata->work_q, &hostdata->main_task);
} else {
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
}
} else
#endif /* REAL_DMA */
{
/* MS: Ignore unknown phase mismatch interrupts (caused by EOP interrupt) */
if (basr & BASR_PHASE_MATCH)
dprintk(NDEBUG_INTR, "scsi%d: unknown interrupt, "
"BASR 0x%x, MR 0x%x, SR 0x%x\n",
HOSTNO, basr, NCR5380_read(MODE_REG),
NCR5380_read(STATUS_REG));
(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) &&
(sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) {
/* Probably reselected */
NCR5380_write(SELECT_ENABLE_REG, 0);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
dprintk(NDEBUG_INTR, "scsi%d: interrupt with SEL and IO\n",
HOSTNO);
if (!hostdata->connected) {
NCR5380_reselect(instance);
queue_work(hostdata->work_q, &hostdata->main_task);
}
if (!hostdata->connected)
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
} else {
/* Probably Bus Reset */
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
dprintk(NDEBUG_INTR, "scsi%d: unknown interrupt\n", HOSTNO);
#ifdef SUN3_SCSI_VME
dregs->csr |= CSR_DMA_ENABLE;
#endif
}
} /* if !(SELECTION || PARITY) */
handled = 1;
} /* BASR & IRQ */ else {
printk(KERN_NOTICE "scsi%d: interrupt without IRQ bit set in BASR, "
"BASR 0x%X, MR 0x%X, SR 0x%x\n", HOSTNO, basr,
NCR5380_read(MODE_REG), NCR5380_read(STATUS_REG));
(void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
} else {
shost_printk(KERN_NOTICE, instance, "interrupt without IRQ bit\n");
#ifdef SUN3_SCSI_VME
dregs->csr |= CSR_DMA_ENABLE;
#endif
}
if (!done)
queue_work(hostdata->work_q, &hostdata->main_task);
return IRQ_RETVAL(handled);
}
......@@ -1509,9 +1513,10 @@ static int NCR5380_select(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
NCR5380_reselect(instance);
if (!hostdata->connected)
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
printk(KERN_ERR "scsi%d: reselection after won arbitration?\n",
HOSTNO);
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
return -1;
}
......@@ -1871,19 +1876,14 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance,
/* send start chain */
sun3scsi_dma_start(c, *data);
NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
MR_ENABLE_EOP_INTR);
if (p & SR_IO) {
NCR5380_write(TARGET_COMMAND_REG, 1);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
NCR5380_write(INITIATOR_COMMAND_REG, 0);
NCR5380_write(MODE_REG,
(NCR5380_read(MODE_REG) | MR_DMA_MODE | MR_ENABLE_EOP_INTR));
NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0);
} else {
NCR5380_write(TARGET_COMMAND_REG, 0);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_ASSERT_DATA);
NCR5380_write(MODE_REG,
(NCR5380_read(MODE_REG) | MR_DMA_MODE | MR_ENABLE_EOP_INTR));
NCR5380_write(START_DMA_SEND_REG, 0);
}
......@@ -1912,10 +1912,8 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance,
c, (p & SR_IO) ? "to" : "from", d);
NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
#ifdef REAL_DMA
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_ENABLE_EOP_INTR | MR_MONITOR_BSY);
#endif /* def REAL_DMA */
NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
MR_ENABLE_EOP_INTR);
if (!(hostdata->flags & FLAG_LATE_DMA_SETUP)) {
/* On the Medusa, it is a must to initialize the DMA before
......@@ -2389,10 +2387,10 @@ static void NCR5380_information_transfer(struct Scsi_Host *instance)
#endif
hostdata->connected = NULL;
cmd->result = DID_ERROR << 16;
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
maybe_release_dma_irq(instance);
local_irq_restore(flags);
cmd->scsi_done(cmd);
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
return;
}
msgout = NOP;
......
......@@ -334,8 +334,6 @@ static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst,
struct NCR5380_hostdata *hostdata = shost_priv(instance);
i = 0;
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR | MR_DMA_MODE);
if (instance->irq == NO_IRQ)
NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ);
else
......@@ -357,9 +355,7 @@ static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst,
rtrc(4);
while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
++i;
NCR5380_write(MODE_REG, 0); /* Clear the operating mode */
rtrc(0);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
if (i > hostdata->spin_max_r)
hostdata->spin_max_r = i;
return (0);
......@@ -383,9 +379,6 @@ static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src,
int i;
struct NCR5380_hostdata *hostdata = shost_priv(instance);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR | MR_DMA_MODE);
/* set direction (write) */
if (instance->irq == NO_IRQ)
NCR5380_write(DTC_CONTROL_REG, 0);
else
......@@ -410,7 +403,6 @@ static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src,
++i;
rtrc(7);
/* Check for parity error here. fixme. */
NCR5380_write(MODE_REG, 0); /* Clear the operating mode */
rtrc(0);
if (i > hostdata->spin_max_w)
hostdata->spin_max_w = i;
......
......@@ -594,8 +594,6 @@ static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst,
if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER))
printk(KERN_ERR "53C400r: no end dma signal\n");
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_read(RESET_PARITY_INTERRUPT_REG);
return 0;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment