Merge branch 'seg6-add-next-c-sid-support-for-srv6-end-behavior'

Andrea Mayer says:

====================
seg6: add NEXT-C-SID support for SRv6 End behavior

The Segment Routing (SR) architecture is based on loose source routing.
A list of instructions, called segments, can be added to the packet headers to
influence the forwarding and processing of the packets in an SR enabled
network.
In SRv6 (Segment Routing over IPv6 data plane) [1], the segment identifiers
(SIDs) are IPv6 addresses (128 bits) and the segment list (SID List) is carried
in the Segment Routing Header (SRH). A segment may correspond to a "behavior"
that is executed by a node when the packet is received.
The Linux kernel currently supports a large subset of the behaviors described
in [2] (e.g., End, End.X, End.T and so on).

Some SRv6 scenarios (i.e.: traffic-engineering, fast-rerouting, VPN, mobile
network backhaul, etc.) may require a large number of segments (i.e. up to 15).
Therefore, reducing the size of the SID List is useful to minimize the impact
on MTU (Maximum Transfer Unit) and to enable SRv6 on legacy hardware devices
with limited processing power that can suffer from long IPv6 headers.

Draft-ietf-spring-srv6-srh-compression [3] extends the SRv6 architecture by
providing different mechanisms for the efficient representation (i.e.
compression) of the SID List.

The NEXT-C-SID mechanism described in [3] offers the possibility of encoding
several SRv6 segments within a single 128 bit SID address. Such a SID address
is called a Compressed SID Container. In this way, the length of the SID List
can be drastically reduced. In some cases, the SRH can be omitted, as the IPv6
Destination Address can carry the whole Segment List, using its compressed
representation.

The NEXT-C-SID mechanism relies on the "flavors" framework defined in [2].
The flavors represent additional operations that can modify or extend a subset
of the existing behaviors.

In this patchset we extend the SRv6 Subsystem in order to support the
NEXT-C-SID mechanism.

In details the patchset is made of:
 - patch 1/3: add netlink_ext_ack support in parsing SRv6 behavior attributes;
 - patch 2/3: add NEXT-C-SID support for SRv6 End behavior;
 - patch 3/3: add selftest for NEXT-C-SID in SRv6 End behavior.

The corresponding iproute2 patch for supporting the NEXT-C-SID in SRv6 End
behavior is provided in a separated patchset.

Comments, improvements and suggestions are always appreciated.

[1] - https://datatracker.ietf.org/doc/html/rfc8754
[2] - https://datatracker.ietf.org/doc/html/rfc8986
[3] - https://datatracker.ietf.org/doc/html/draft-ietf-spring-srv6-srh-compression

====================

Link: https://lore.kernel.org/r/20220912171619.16943-1-andrea.mayer@uniroma2.itSigned-off-by: Paolo Abeni <pabeni@redhat.com>

include/uapi/linux/seg6_local.h

@@ -28,6 +28,7 @@ enum {
 	SEG6_LOCAL_BPF,
 	SEG6_LOCAL_VRFTABLE,
 	SEG6_LOCAL_COUNTERS,
+	SEG6_LOCAL_FLAVORS,
 	__SEG6_LOCAL_MAX,
 };
 #define SEG6_LOCAL_MAX (__SEG6_LOCAL_MAX - 1)
@@ -110,4 +111,27 @@ enum {
 
 #define SEG6_LOCAL_CNT_MAX (__SEG6_LOCAL_CNT_MAX - 1)
 
+/* SRv6 End* Flavor attributes */
+enum {
+	SEG6_LOCAL_FLV_UNSPEC,
+	SEG6_LOCAL_FLV_OPERATION,
+	SEG6_LOCAL_FLV_LCBLOCK_BITS,
+	SEG6_LOCAL_FLV_LCNODE_FN_BITS,
+	__SEG6_LOCAL_FLV_MAX,
+};
+
+#define SEG6_LOCAL_FLV_MAX (__SEG6_LOCAL_FLV_MAX - 1)
+
+/* Designed flavor operations for SRv6 End* Behavior */
+enum {
+	SEG6_LOCAL_FLV_OP_UNSPEC,
+	SEG6_LOCAL_FLV_OP_PSP,
+	SEG6_LOCAL_FLV_OP_USP,
+	SEG6_LOCAL_FLV_OP_USD,
+	SEG6_LOCAL_FLV_OP_NEXT_CSID,
+	__SEG6_LOCAL_FLV_OP_MAX
+};
+
+#define SEG6_LOCAL_FLV_OP_MAX (__SEG6_LOCAL_FLV_OP_MAX - 1)
+
 #endif

tools/testing/selftests/net/Makefile

@@ -37,6 +37,7 @@ TEST_PROGS += srv6_end_dt4_l3vpn_test.sh
 TEST_PROGS += srv6_end_dt6_l3vpn_test.sh
 TEST_PROGS += srv6_hencap_red_l3vpn_test.sh
 TEST_PROGS += srv6_hl2encap_red_l2vpn_test.sh
+TEST_PROGS += srv6_end_next_csid_l3vpn_test.sh
 TEST_PROGS += vrf_strict_mode_test.sh
 TEST_PROGS += arp_ndisc_evict_nocarrier.sh
 TEST_PROGS += ndisc_unsolicited_na_test.sh