Merge tag 'spi-fix-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi fixes from Mark Brown:
 "A small collection of driver specific fixes that have come in since
  the merge window, nothing too major here but all good to have"

* tag 'spi-fix-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: fsl-dspi: fix wrong pointer in suspend/resume
  spi: bcm2835: fix gpio cs level inversion
  spi: imx: fix runtime pm support for !CONFIG_PM

drivers/spi/spi-bcm2835.c

@@ -1259,18 +1259,6 @@ static int bcm2835_spi_setup(struct spi_device *spi)
 	if (!chip)
 		return 0;
 
-	/*
-	 * Retrieve the corresponding GPIO line used for CS.
-	 * The inversion semantics will be handled by the GPIO core
-	 * code, so we pass GPIOD_OUT_LOW for "unasserted" and
-	 * the correct flag for inversion semantics. The SPI_CS_HIGH
-	 * on spi->mode cannot be checked for polarity in this case
-	 * as the flag use_gpio_descriptors enforces SPI_CS_HIGH.
-	 */
-	if (of_property_read_bool(spi->dev.of_node, "spi-cs-high"))
-		lflags = GPIO_ACTIVE_HIGH;
-	else
-		lflags = GPIO_ACTIVE_LOW;
 	spi->cs_gpiod = gpiochip_request_own_desc(chip, 8 - spi->chip_select,
 						  DRV_NAME,
 						  lflags,

drivers/spi/spi-fsl-dspi.c

@@ -1080,12 +1080,11 @@ MODULE_DEVICE_TABLE(of, fsl_dspi_dt_ids);
 #ifdef CONFIG_PM_SLEEP
 static int dspi_suspend(struct device *dev)
 {
-	struct spi_controller *ctlr = dev_get_drvdata(dev);
-	struct fsl_dspi *dspi = spi_controller_get_devdata(ctlr);
+	struct fsl_dspi *dspi = dev_get_drvdata(dev);
 
 	if (dspi->irq)
 		disable_irq(dspi->irq);
-	spi_controller_suspend(ctlr);
+	spi_controller_suspend(dspi->ctlr);
 	clk_disable_unprepare(dspi->clk);
 
 	pinctrl_pm_select_sleep_state(dev);
@@ -1095,8 +1094,7 @@ static int dspi_suspend(struct device *dev)
 
 static int dspi_resume(struct device *dev)
 {
-	struct spi_controller *ctlr = dev_get_drvdata(dev);
-	struct fsl_dspi *dspi = spi_controller_get_devdata(ctlr);
+	struct fsl_dspi *dspi = dev_get_drvdata(dev);
 	int ret;
 
 	pinctrl_pm_select_default_state(dev);
@@ -1104,7 +1102,7 @@ static int dspi_resume(struct device *dev)
 	ret = clk_prepare_enable(dspi->clk);
 	if (ret)
 		return ret;
-	spi_controller_resume(ctlr);
+	spi_controller_resume(dspi->ctlr);
 	if (dspi->irq)
 		enable_irq(dspi->irq);
 

drivers/spi/spi-imx.c

@@ -1676,15 +1676,18 @@ static int spi_imx_probe(struct platform_device *pdev)
 		goto out_master_put;
 	}
 
-	pm_runtime_enable(spi_imx->dev);
+	ret = clk_prepare_enable(spi_imx->clk_per);
+	if (ret)
+		goto out_master_put;
+
+	ret = clk_prepare_enable(spi_imx->clk_ipg);
+	if (ret)
+		goto out_put_per;
+
 	pm_runtime_set_autosuspend_delay(spi_imx->dev, MXC_RPM_TIMEOUT);
 	pm_runtime_use_autosuspend(spi_imx->dev);
-
-	ret = pm_runtime_get_sync(spi_imx->dev);
-	if (ret < 0) {
-		dev_err(spi_imx->dev, "failed to enable clock\n");
-		goto out_runtime_pm_put;
-	}
+	pm_runtime_set_active(spi_imx->dev);
+	pm_runtime_enable(spi_imx->dev);
 
 	spi_imx->spi_clk = clk_get_rate(spi_imx->clk_per);
 	/*
@@ -1722,8 +1725,12 @@ static int spi_imx_probe(struct platform_device *pdev)
 		spi_imx_sdma_exit(spi_imx);
 out_runtime_pm_put:
 	pm_runtime_dont_use_autosuspend(spi_imx->dev);
-	pm_runtime_put_sync(spi_imx->dev);
+	pm_runtime_set_suspended(&pdev->dev);
 	pm_runtime_disable(spi_imx->dev);
+
+	clk_disable_unprepare(spi_imx->clk_ipg);
+out_put_per:
+	clk_disable_unprepare(spi_imx->clk_per);
 out_master_put:
 	spi_master_put(master);