Merge branch 'depends/rmk/memory_h' into next/cleanup2

There are lots of conflicts between the omap and exynos cleanups
and the memory.h remove series.

Conflicts:
	arch/arm/mach-exynos4/mach-smdkc210.c
	arch/arm/mach-exynos4/mach-smdkv310.c
	arch/arm/mach-imx/mach-cpuimx27.c
	arch/arm/mach-omap1/board-ams-delta.c
	arch/arm/mach-omap1/board-generic.c
	arch/arm/mach-omap1/board-h2.c
	arch/arm/mach-omap1/board-h3.c
	arch/arm/mach-omap1/board-nokia770.c
	arch/arm/mach-omap1/board-osk.c
	arch/arm/mach-omap1/board-palmte.c
	arch/arm/mach-omap1/board-palmtt.c
	arch/arm/mach-omap1/board-palmz71.c
	arch/arm/mach-omap1/board-sx1.c
	arch/arm/mach-omap1/board-voiceblue.c
	arch/arm/mach-omap1/io.c
	arch/arm/mach-omap2/board-generic.c
	arch/arm/mach-omap2/io.c
	arch/arm/plat-omap/io.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/Kconfig

@@ -195,7 +195,8 @@ config VECTORS_BASE
 	  The base address of exception vectors.
 
 config ARM_PATCH_PHYS_VIRT
-	bool "Patch physical to virtual translations at runtime"
+	bool "Patch physical to virtual translations at runtime" if EMBEDDED
+	default y
 	depends on !XIP_KERNEL && MMU
 	depends on !ARCH_REALVIEW || !SPARSEMEM
 	help
@@ -204,16 +205,25 @@ config ARM_PATCH_PHYS_VIRT
 	  kernel in system memory.
 
 	  This can only be used with non-XIP MMU kernels where the base
-	  of physical memory is at a 16MB boundary, or theoretically 64K
-	  for the MSM machine class.
+	  of physical memory is at a 16MB boundary.
 
-config ARM_PATCH_PHYS_VIRT_16BIT
-	def_bool y
-	depends on ARM_PATCH_PHYS_VIRT && ARCH_MSM
+	  Only disable this option if you know that you do not require
+	  this feature (eg, building a kernel for a single machine) and
+	  you need to shrink the kernel to the minimal size.
+
+config NEED_MACH_MEMORY_H
+	bool
+	help
+	  Select this when mach/memory.h is required to provide special
+	  definitions for this platform.  The need for mach/memory.h should
+	  be avoided when possible.
+
+config PHYS_OFFSET
+	hex "Physical address of main memory"
+	depends on !ARM_PATCH_PHYS_VIRT && !NEED_MACH_MEMORY_H
 	help
-	  This option extends the physical to virtual translation patching
-	  to allow physical memory down to a theoretical minimum of 64K
-	  boundaries.
+	  Please provide the physical address corresponding to the
+	  location of main memory in your system.
 
 source "init/Kconfig"
 
@@ -246,6 +256,7 @@ config ARCH_INTEGRATOR
 	select GENERIC_CLOCKEVENTS
 	select PLAT_VERSATILE
 	select PLAT_VERSATILE_FPGA_IRQ
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for ARM's Integrator platform.
 
@@ -261,6 +272,7 @@ config ARCH_REALVIEW
 	select PLAT_VERSATILE_CLCD
 	select ARM_TIMER_SP804
 	select GPIO_PL061 if GPIOLIB
+	select NEED_MACH_MEMORY_H
 	help
 	  This enables support for ARM Ltd RealView boards.
 
@@ -301,7 +313,6 @@ config ARCH_AT91
 	select ARCH_REQUIRE_GPIOLIB
 	select HAVE_CLK
 	select CLKDEV_LOOKUP
-	select ARM_PATCH_PHYS_VIRT if MMU
 	help
 	  This enables support for systems based on the Atmel AT91RM9200,
 	  AT91SAM9 and AT91CAP9 processors.
@@ -322,6 +333,7 @@ config ARCH_CLPS711X
 	bool "Cirrus Logic CLPS711x/EP721x-based"
 	select CPU_ARM720T
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Cirrus Logic 711x/721x based boards.
 
@@ -362,6 +374,7 @@ config ARCH_EBSA110
 	select ISA
 	select NO_IOPORT
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  This is an evaluation board for the StrongARM processor available
 	  from Digital. It has limited hardware on-board, including an
@@ -377,6 +390,7 @@ config ARCH_EP93XX
 	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MEMORY_H
 	help
 	  This enables support for the Cirrus EP93xx series of CPUs.
 
@@ -385,6 +399,7 @@ config ARCH_FOOTBRIDGE
 	select CPU_SA110
 	select FOOTBRIDGE
 	select GENERIC_CLOCKEVENTS
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for systems based on the DC21285 companion chip
 	  ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
@@ -434,6 +449,7 @@ config ARCH_IOP13XX
 	select PCI
 	select ARCH_SUPPORTS_MSI
 	select VMSPLIT_1G
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Intel's IOP13XX (XScale) family of processors.
 
@@ -464,6 +480,7 @@ config ARCH_IXP23XX
 	select CPU_XSC3
  	select PCI
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Intel's IXP23xx (XScale) family of processors.
 
@@ -473,6 +490,7 @@ config ARCH_IXP2000
 	select CPU_XSCALE
 	select PCI
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Intel's IXP2400/2800 (XScale) family of processors.
 
@@ -566,6 +584,7 @@ config ARCH_KS8695
 	select CPU_ARM922T
 	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
 	  System-on-Chip devices.
@@ -657,6 +676,7 @@ config ARCH_SHMOBILE
 	select SPARSE_IRQ
 	select MULTI_IRQ_HANDLER
 	select PM_GENERIC_DOMAINS if PM
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for Renesas's SH-Mobile and R-Mobile ARM platforms.
 
@@ -671,6 +691,7 @@ config ARCH_RPC
 	select NO_IOPORT
 	select ARCH_SPARSEMEM_ENABLE
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  On the Acorn Risc-PC, Linux can support the internal IDE disk and
 	  CD-ROM interface, serial and parallel port, and the floppy drive.
@@ -689,6 +710,7 @@ config ARCH_SA1100
 	select HAVE_SCHED_CLOCK
 	select TICK_ONESHOT
 	select ARCH_REQUIRE_GPIOLIB
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for StrongARM 11x0 based boards.
 
@@ -778,6 +800,7 @@ config ARCH_S5PV210
 	select HAVE_S3C2410_I2C if I2C
 	select HAVE_S3C_RTC if RTC_CLASS
 	select HAVE_S3C2410_WATCHDOG if WATCHDOG
+	select NEED_MACH_MEMORY_H
 	help
 	  Samsung S5PV210/S5PC110 series based systems
 
@@ -794,6 +817,7 @@ config ARCH_EXYNOS4
 	select HAVE_S3C_RTC if RTC_CLASS
 	select HAVE_S3C2410_I2C if I2C
 	select HAVE_S3C2410_WATCHDOG if WATCHDOG
+	select NEED_MACH_MEMORY_H
 	help
 	  Samsung EXYNOS4 series based systems
 
@@ -805,6 +829,7 @@ config ARCH_SHARK
 	select ZONE_DMA
 	select PCI
 	select ARCH_USES_GETTIMEOFFSET
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for the StrongARM based Digital DNARD machine, also known
 	  as "Shark" (<http://www.shark-linux.de/shark.html>).
@@ -832,6 +857,7 @@ config ARCH_U300
 	select CLKDEV_LOOKUP
 	select HAVE_MACH_CLKDEV
 	select GENERIC_GPIO
+	select NEED_MACH_MEMORY_H
 	help
 	  Support for ST-Ericsson U300 series mobile platforms.
 

arch/arm/Makefile

@@ -128,6 +128,9 @@ textofs-$(CONFIG_PM_H1940)      := 0x00108000
 ifeq ($(CONFIG_ARCH_SA1100),y)
 textofs-$(CONFIG_SA1111) := 0x00208000
 endif
+textofs-$(CONFIG_ARCH_MSM7X30) := 0x00208000
+textofs-$(CONFIG_ARCH_MSM8X60) := 0x00208000
+textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
 
 # Machine directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.

arch/arm/include/asm/dma-mapping.h

@@ -205,6 +205,13 @@ extern void *dma_alloc_writecombine(struct device *, size_t, dma_addr_t *,
 int dma_mmap_writecombine(struct device *, struct vm_area_struct *,
 		void *, dma_addr_t, size_t);
 
+/*
+ * This can be called during boot to increase the size of the consistent
+ * DMA region above it's default value of 2MB. It must be called before the
+ * memory allocator is initialised, i.e. before any core_initcall.
+ */
+extern void __init init_consistent_dma_size(unsigned long size);
+
 
 #ifdef CONFIG_DMABOUNCE
 /*

arch/arm/include/asm/mach/arch.h

@@ -17,7 +17,7 @@ struct sys_timer;
 struct machine_desc {
 	unsigned int		nr;		/* architecture number	*/
 	const char		*name;		/* architecture name	*/
-	unsigned long		boot_params;	/* tagged list		*/
+	unsigned long		atag_offset;	/* tagged list (relative) */
 	const char		**dt_compat;	/* array of device tree
 						 * 'compatible' strings	*/
 

arch/arm/include/asm/memory.h

@@ -16,9 +16,12 @@
 #include <linux/compiler.h>
 #include <linux/const.h>
 #include <linux/types.h>
-#include <mach/memory.h>
 #include <asm/sizes.h>
 
+#ifdef CONFIG_NEED_MACH_MEMORY_H
+#include <mach/memory.h>
+#endif
+
 /*
  * Allow for constants defined here to be used from assembly code
  * by prepending the UL suffix only with actual C code compilation.
@@ -77,16 +80,7 @@
  */
 #define IOREMAP_MAX_ORDER	24
 
-/*
- * Size of DMA-consistent memory region.  Must be multiple of 2M,
- * between 2MB and 14MB inclusive.
- */
-#ifndef CONSISTENT_DMA_SIZE
-#define CONSISTENT_DMA_SIZE 	SZ_2M
-#endif
-
 #define CONSISTENT_END		(0xffe00000UL)
-#define CONSISTENT_BASE		(CONSISTENT_END - CONSISTENT_DMA_SIZE)
 
 #else /* CONFIG_MMU */
 
@@ -160,7 +154,6 @@
  * so that all we need to do is modify the 8-bit constant field.
  */
 #define __PV_BITS_31_24	0x81000000
-#define __PV_BITS_23_16	0x00810000
 
 extern unsigned long __pv_phys_offset;
 #define PHYS_OFFSET __pv_phys_offset
@@ -178,9 +171,6 @@ static inline unsigned long __virt_to_phys(unsigned long x)
 {
 	unsigned long t;
 	__pv_stub(x, t, "add", __PV_BITS_31_24);
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	__pv_stub(t, t, "add", __PV_BITS_23_16);
-#endif
 	return t;
 }
 
@@ -188,9 +178,6 @@ static inline unsigned long __phys_to_virt(unsigned long x)
 {
 	unsigned long t;
 	__pv_stub(x, t, "sub", __PV_BITS_31_24);
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	__pv_stub(t, t, "sub", __PV_BITS_23_16);
-#endif
 	return t;
 }
 #else
@@ -200,7 +187,11 @@ static inline unsigned long __phys_to_virt(unsigned long x)
 #endif
 
 #ifndef PHYS_OFFSET
+#ifdef PLAT_PHYS_OFFSET
 #define PHYS_OFFSET	PLAT_PHYS_OFFSET
+#else
+#define PHYS_OFFSET	UL(CONFIG_PHYS_OFFSET)
+#endif
 #endif
 
 /*

arch/arm/include/asm/module.h

@@ -31,11 +31,7 @@ struct mod_arch_specific {
 
 /* Add __virt_to_phys patching state as well */
 #ifdef CONFIG_ARM_PATCH_PHYS_VIRT
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-#define MODULE_ARCH_VERMAGIC_P2V "p2v16 "
-#else
 #define MODULE_ARCH_VERMAGIC_P2V "p2v8 "
-#endif
 #else
 #define MODULE_ARCH_VERMAGIC_P2V ""
 #endif

arch/arm/kernel/debug.S

@@ -22,7 +22,7 @@
 #if defined(CONFIG_DEBUG_ICEDCC)
 		@@ debug using ARM EmbeddedICE DCC channel
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		.endm
 
 #if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_V6K) || defined(CONFIG_CPU_V7)
@@ -106,7 +106,7 @@
 
 #ifdef CONFIG_MMU
 		.macro	addruart_current, rx, tmp1, tmp2
-		addruart	\tmp1, \tmp2
+		addruart	\tmp1, \tmp2, \rx
 		mrc		p15, 0, \rx, c1, c0
 		tst		\rx, #1
 		moveq		\rx, \tmp1

arch/arm/kernel/head.S

@@ -95,7 +95,7 @@ ENTRY(stext)
 	sub	r4, r3, r4			@ (PHYS_OFFSET - PAGE_OFFSET)
 	add	r8, r8, r4			@ PHYS_OFFSET
 #else
-	ldr	r8, =PLAT_PHYS_OFFSET
+	ldr	r8, =PHYS_OFFSET		@ always constant in this case
 #endif
 
 	/*
@@ -234,7 +234,7 @@ __create_page_tables:
 	 * This allows debug messages to be output
 	 * via a serial console before paging_init.
 	 */
-	addruart r7, r3
+	addruart r7, r3, r0
 
 	mov	r3, r3, lsr #20
 	mov	r3, r3, lsl #2
@@ -488,13 +488,8 @@ __fixup_pv_table:
 	add	r5, r5, r3	@ adjust table end address
 	add	r7, r7, r3	@ adjust __pv_phys_offset address
 	str	r8, [r7]	@ save computed PHYS_OFFSET to __pv_phys_offset
-#ifndef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
 	mov	r6, r3, lsr #24	@ constant for add/sub instructions
 	teq	r3, r6, lsl #24 @ must be 16MiB aligned
-#else
-	mov	r6, r3, lsr #16	@ constant for add/sub instructions
-	teq	r3, r6, lsl #16	@ must be 64kiB aligned
-#endif
 THUMB(	it	ne		@ cross section branch )
 	bne	__error
 	str	r6, [r7, #4]	@ save to __pv_offset
@@ -510,20 +505,8 @@ ENDPROC(__fixup_pv_table)
 	.text
 __fixup_a_pv_table:
 #ifdef CONFIG_THUMB2_KERNEL
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	lsls	r0, r6, #24
-	lsr	r6, #8
-	beq	1f
-	clz	r7, r0
-	lsr	r0, #24
-	lsl	r0, r7
-	bic	r0, 0x0080
-	lsrs	r7, #1
-	orrcs   r0, #0x0080
-	orr	r0, r0, r7, lsl #12
-#endif
-1:	lsls	r6, #24
-	beq	4f
+	lsls	r6, #24
+	beq	2f
 	clz	r7, r6
 	lsr	r6, #24
 	lsl	r6, r7
@@ -532,43 +515,25 @@ __fixup_a_pv_table:
 	orrcs	r6, #0x0080
 	orr	r6, r6, r7, lsl #12
 	orr	r6, #0x4000
-	b	4f
-2:	@ at this point the C flag is always clear
-	add     r7, r3
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	ldrh	ip, [r7]
-	tst	ip, 0x0400	@ the i bit tells us LS or MS byte
-	beq	3f
-	cmp	r0, #0		@ set C flag, and ...
-	biceq	ip, 0x0400	@ immediate zero value has a special encoding
-	streqh	ip, [r7]	@ that requires the i bit cleared
-#endif
-3:	ldrh	ip, [r7, #2]
+	b	2f
+1:	add     r7, r3
+	ldrh	ip, [r7, #2]
 	and	ip, 0x8f00
-	orrcc	ip, r6	@ mask in offset bits 31-24
-	orrcs	ip, r0	@ mask in offset bits 23-16
+	orr	ip, r6	@ mask in offset bits 31-24
 	strh	ip, [r7, #2]
-4:	cmp	r4, r5
+2:	cmp	r4, r5
 	ldrcc	r7, [r4], #4	@ use branch for delay slot
-	bcc	2b
+	bcc	1b
 	bx	lr
 #else
-#ifdef CONFIG_ARM_PATCH_PHYS_VIRT_16BIT
-	and	r0, r6, #255	@ offset bits 23-16
-	mov	r6, r6, lsr #8	@ offset bits 31-24
-#else
-	mov	r0, #0		@ just in case...
-#endif
-	b	3f
-2:	ldr	ip, [r7, r3]
+	b	2f
+1:	ldr	ip, [r7, r3]
 	bic	ip, ip, #0x000000ff
-	tst	ip, #0x400	@ rotate shift tells us LS or MS byte
-	orrne	ip, ip, r6	@ mask in offset bits 31-24
-	orreq	ip, ip, r0	@ mask in offset bits 23-16
+	orr	ip, ip, r6	@ mask in offset bits 31-24
 	str	ip, [r7, r3]
-3:	cmp	r4, r5
+2:	cmp	r4, r5
 	ldrcc	r7, [r4], #4	@ use branch for delay slot
-	bcc	2b
+	bcc	1b
 	mov	pc, lr
 #endif
 ENDPROC(__fixup_a_pv_table)

arch/arm/kernel/setup.c

@@ -820,25 +820,8 @@ static struct machine_desc * __init setup_machine_tags(unsigned int nr)
 
 	if (__atags_pointer)
 		tags = phys_to_virt(__atags_pointer);
-	else if (mdesc->boot_params) {
-#ifdef CONFIG_MMU
-		/*
-		 * We still are executing with a minimal MMU mapping created
-		 * with the presumption that the machine default for this
-		 * is located in the first MB of RAM.  Anything else will
-		 * fault and silently hang the kernel at this point.
-		 */
-		if (mdesc->boot_params < PHYS_OFFSET ||
-		    mdesc->boot_params >= PHYS_OFFSET + SZ_1M) {
-			printk(KERN_WARNING
-			       "Default boot params at physical 0x%08lx out of reach\n",
-			       mdesc->boot_params);
-		} else
-#endif
-		{
-			tags = phys_to_virt(mdesc->boot_params);
-		}
-	}
+	else if (mdesc->atag_offset)
+		tags = (void *)(PAGE_OFFSET + mdesc->atag_offset);
 
 #if defined(CONFIG_DEPRECATED_PARAM_STRUCT)
 	/*

arch/arm/mach-at91/at91sam9g45.c

@@ -12,6 +12,7 @@
 
 #include <linux/module.h>
 #include <linux/pm.h>
+#include <linux/dma-mapping.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -319,6 +320,7 @@ static void at91sam9g45_poweroff(void)
 static void __init at91sam9g45_map_io(void)
 {
 	at91_init_sram(0, AT91SAM9G45_SRAM_BASE, AT91SAM9G45_SRAM_SIZE);
+	init_consistent_dma_size(SZ_4M);
 }
 
 static void __init at91sam9g45_initialize(void)

arch/arm/mach-at91/include/mach/at91sam9g45.h

@@ -128,8 +128,6 @@
 #define AT91SAM9G45_EHCI_BASE	0x00800000	/* USB Host controller (EHCI) */
 #define AT91SAM9G45_VDEC_BASE	0x00900000	/* Video Decoder Controller */
 
-#define CONSISTENT_DMA_SIZE	SZ_4M
-
 /*
  * DMA peripheral identifiers
  * for hardware handshaking interface

arch/arm/mach-at91/include/mach/debug-macro.S

@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <mach/at91_dbgu.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =(AT91_BASE_SYS + AT91_DBGU)	@ System peripherals (phys address)
 	ldr	\rv, =(AT91_VA_BASE_SYS	+ AT91_DBGU)	@ System peripherals (virt address)
 	.endm

arch/arm/mach-bcmring/include/mach/hardware.h

@@ -22,7 +22,6 @@
 #define __ASM_ARCH_HARDWARE_H
 
 #include <asm/sizes.h>
-#include <mach/memory.h>
 #include <cfg_global.h>
 #include <mach/csp/mm_io.h>
 
@@ -31,7 +30,7 @@
  *  *_SIZE  is the size of the region
  *  *_BASE  is the virtual address
  */
-#define RAM_START               PLAT_PHYS_OFFSET
+#define RAM_START               PHYS_OFFSET
 
 #define RAM_SIZE                (CFG_GLOBAL_RAM_SIZE-CFG_GLOBAL_RAM_SIZE_RESERVED)
 #define RAM_BASE                PAGE_OFFSET

arch/arm/mach-bcmring/include/mach/memory.h

-/*****************************************************************************
-* Copyright 2005 - 2008 Broadcom Corporation.  All rights reserved.
-*
-* Unless you and Broadcom execute a separate written software license
-* agreement governing use of this software, this software is licensed to you
-* under the terms of the GNU General Public License version 2, available at
-* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
-*
-* Notwithstanding the above, under no circumstances may you combine this
-* software in any way with any other Broadcom software provided under a
-* license other than the GPL, without Broadcom's express prior written
-* consent.
-*****************************************************************************/
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#include <cfg_global.h>
-
-/*
- * Physical vs virtual RAM address space conversion.  These are
- * private definitions which should NOT be used outside memory.h
- * files.  Use virt_to_phys/phys_to_virt/__pa/__va instead.
- */
-
-#define PLAT_PHYS_OFFSET CFG_GLOBAL_RAM_BASE
-
-/*
- * Maximum DMA memory allowed is 14M
- */
-#define CONSISTENT_DMA_SIZE (SZ_16M - SZ_2M)
-
-#endif

arch/arm/mach-bcmring/mm.c

@@ -13,6 +13,7 @@
 *****************************************************************************/
 
 #include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
 #include <asm/mach/map.h>
 
 #include <mach/hardware.h>
@@ -53,4 +54,6 @@ void __init bcmring_map_io(void)
 {
 
 	iotable_init(bcmring_io_desc, ARRAY_SIZE(bcmring_io_desc));
+	/* Maximum DMA memory allowed is 14M */
+	init_consistent_dma_size(14 << 20);
 }

arch/arm/mach-clps711x/autcpu12.c

@@ -64,7 +64,7 @@ void __init autcpu12_map_io(void)
 
 MACHINE_START(AUTCPU12, "autronix autcpu12")
 	/* Maintainer: Thomas Gleixner */
-	.boot_params	= 0xc0020000,
+	.atag_offset	= 0x20000,
 	.map_io		= autcpu12_map_io,
 	.init_irq	= clps711x_init_irq,
 	.timer		= &clps711x_timer,

arch/arm/mach-clps711x/cdb89712.c

@@ -55,7 +55,7 @@ static void __init cdb89712_map_io(void)
 
 MACHINE_START(CDB89712, "Cirrus-CDB89712")
 	/* Maintainer: Ray Lehtiniemi */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= cdb89712_map_io,
 	.init_irq	= clps711x_init_irq,
 	.timer		= &clps711x_timer,

arch/arm/mach-clps711x/ceiva.c

@@ -56,7 +56,7 @@ static void __init ceiva_map_io(void)
 
 MACHINE_START(CEIVA, "CEIVA/Polaroid Photo MAX Digital Picture Frame")
 	/* Maintainer: Rob Scott */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.map_io		= ceiva_map_io,
 	.init_irq	= clps711x_init_irq,
 	.timer		= &clps711x_timer,

arch/arm/mach-clps711x/clep7312.c

@@ -37,7 +37,7 @@ fixup_clep7312(struct machine_desc *desc, struct tag *tags,
 
 MACHINE_START(CLEP7212, "Cirrus Logic 7212/7312")
 	/* Maintainer: Nobody */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x0100,
 	.fixup		= fixup_clep7312,
 	.map_io		= clps711x_map_io,
 	.init_irq	= clps711x_init_irq,

arch/arm/mach-clps711x/edb7211-arch.c

@@ -57,7 +57,7 @@ fixup_edb7211(struct machine_desc *desc, struct tag *tags,
 
 MACHINE_START(EDB7211, "CL-EDB7211 (EP7211 eval board)")
 	/* Maintainer: Jon McClintock */
-	.boot_params	= 0xc0020100,	/* 0xc0000000 - 0xc001ffff can be video RAM */
+	.atag_offset	= 0x20100,	/* 0xc0000000 - 0xc001ffff can be video RAM */
 	.fixup		= fixup_edb7211,
 	.map_io		= edb7211_map_io,
 	.reserve	= edb7211_reserve,

arch/arm/mach-clps711x/fortunet.c

@@ -75,7 +75,6 @@ fortunet_fixup(struct machine_desc *desc, struct tag *tags,
 
 MACHINE_START(FORTUNET, "ARM-FortuNet")
 	/* Maintainer: FortuNet Inc. */
-	.boot_params	= 0x00000000,
 	.fixup		= fortunet_fixup,
 	.map_io		= clps711x_map_io,
 	.init_irq	= clps711x_init_irq,

arch/arm/mach-clps711x/include/mach/debug-macro.S

@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <asm/hardware/clps7111.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 #ifndef CONFIG_DEBUG_CLPS711X_UART2
 		mov	\rp, #0x0000	@ UART1
 #else

arch/arm/mach-clps711x/p720t.c

@@ -89,7 +89,7 @@ static void __init p720t_map_io(void)
 
 MACHINE_START(P720T, "ARM-Prospector720T")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.boot_params	= 0xc0000100,
+	.atag_offset	= 0x100,
 	.fixup		= fixup_p720t,
 	.map_io		= p720t_map_io,
 	.init_irq	= clps711x_init_irq,

arch/arm/mach-cns3xxx/cns3420vb.c

@@ -197,7 +197,7 @@ static void __init cns3420_map_io(void)
 }
 
 MACHINE_START(CNS3420VB, "Cavium Networks CNS3420 Validation Board")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= cns3420_map_io,
 	.init_irq	= cns3xxx_init_irq,
 	.timer		= &cns3xxx_timer,

arch/arm/mach-cns3xxx/include/mach/debug-macro.S

@@ -10,7 +10,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart,rp,rv
+		.macro	addruart,rp,rv,tmp
 		mov	\rp, #0x00009000
 		orr	\rv, \rp, #0xf0000000	@ virtual base
 		orr	\rp, \rp, #0x10000000

arch/arm/mach-cns3xxx/include/mach/memory.h

-/*
- * Copyright 2003 ARM Limited
- * Copyright 2008 Cavium Networks
- *
- * This file is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License, Version 2, as
- * published by the Free Software Foundation.
- */
-
-#ifndef __MACH_MEMORY_H
-#define __MACH_MEMORY_H
-
-/*
- * Physical DRAM offset.
- */
-#define PLAT_PHYS_OFFSET		UL(0x00000000)
-
-#define __phys_to_bus(x)	((x) + PHYS_OFFSET)
-#define __bus_to_phys(x)	((x) - PHYS_OFFSET)
-
-#define __virt_to_bus(v)	__phys_to_bus(__virt_to_phys(v))
-#define __bus_to_virt(b)	__phys_to_virt(__bus_to_phys(b))
-#define __pfn_to_bus(p)		__phys_to_bus(__pfn_to_phys(p))
-#define __bus_to_pfn(b)		__phys_to_pfn(__bus_to_phys(b))
-
-#endif

arch/arm/mach-davinci/board-da830-evm.c

@@ -676,7 +676,7 @@ static void __init da830_evm_map_io(void)
 }
 
 MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM")
-	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= da830_evm_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,

arch/arm/mach-davinci/board-da850-evm.c

@@ -1291,7 +1291,7 @@ static void __init da850_evm_map_io(void)
 }
 
 MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138/AM18x EVM")
-	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= da850_evm_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,

arch/arm/mach-davinci/board-dm355-evm.c

@@ -351,7 +351,7 @@ static __init void dm355_evm_init(void)
 }
 
 MACHINE_START(DAVINCI_DM355_EVM, "DaVinci DM355 EVM")
-	.boot_params  = (0x80000100),
+	.atag_offset  = 0x100,
 	.map_io	      = dm355_evm_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer	      = &davinci_timer,

arch/arm/mach-davinci/board-dm355-leopard.c

@@ -270,7 +270,7 @@ static __init void dm355_leopard_init(void)
 }
 
 MACHINE_START(DM355_LEOPARD, "DaVinci DM355 leopard")
-	.boot_params  = (0x80000100),
+	.atag_offset  = 0x100,
 	.map_io	      = dm355_leopard_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer	      = &davinci_timer,

arch/arm/mach-davinci/board-dm365-evm.c

@@ -612,7 +612,7 @@ static __init void dm365_evm_init(void)
 }
 
 MACHINE_START(DAVINCI_DM365_EVM, "DaVinci DM365 EVM")
-	.boot_params	= (0x80000100),
+	.atag_offset	= 0x100,
 	.map_io		= dm365_evm_map_io,
 	.init_irq	= davinci_irq_init,
 	.timer		= &davinci_timer,

arch/arm/mach-davinci/board-dm644x-evm.c

@@ -712,7 +712,7 @@ static __init void davinci_evm_init(void)
 
 MACHINE_START(DAVINCI_EVM, "DaVinci DM644x EVM")
 	/* Maintainer: MontaVista Software <source@mvista.com> */
-	.boot_params  = (DAVINCI_DDR_BASE + 0x100),
+	.atag_offset  = 0x100,
 	.map_io	      = davinci_evm_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer	      = &davinci_timer,

arch/arm/mach-davinci/board-dm646x-evm.c

@@ -792,7 +792,7 @@ static __init void evm_init(void)
 }
 
 MACHINE_START(DAVINCI_DM6467_EVM, "DaVinci DM646x EVM")
-	.boot_params  = (0x80000100),
+	.atag_offset  = 0x100,
 	.map_io       = davinci_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer        = &davinci_timer,
@@ -801,7 +801,7 @@ MACHINE_START(DAVINCI_DM6467_EVM, "DaVinci DM646x EVM")
 MACHINE_END
 
 MACHINE_START(DAVINCI_DM6467TEVM, "DaVinci DM6467T EVM")
-	.boot_params  = (0x80000100),
+	.atag_offset  = 0x100,
 	.map_io       = davinci_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer        = &davinci_timer,

arch/arm/mach-davinci/board-mityomapl138.c

@@ -566,7 +566,7 @@ static void __init mityomapl138_map_io(void)
 }
 
 MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808")
-	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= mityomapl138_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,

arch/arm/mach-davinci/board-neuros-osd2.c

@@ -272,7 +272,7 @@ static __init void davinci_ntosd2_init(void)
 
 MACHINE_START(NEUROS_OSD2, "Neuros OSD2")
 	/* Maintainer: Neuros Technologies <neuros@groups.google.com> */
-	.boot_params	= (DAVINCI_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		 = davinci_ntosd2_map_io,
 	.init_irq	= davinci_irq_init,
 	.timer		= &davinci_timer,

arch/arm/mach-davinci/board-omapl138-hawk.c

@@ -338,7 +338,7 @@ static void __init omapl138_hawk_map_io(void)
 }
 
 MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard")
-	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= omapl138_hawk_map_io,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,

arch/arm/mach-davinci/board-sffsdr.c

@@ -151,7 +151,7 @@ static __init void davinci_sffsdr_init(void)
 
 MACHINE_START(SFFSDR, "Lyrtech SFFSDR")
 	/* Maintainer: Hugo Villeneuve hugo.villeneuve@lyrtech.com */
-	.boot_params  = (DAVINCI_DDR_BASE + 0x100),
+	.atag_offset  = 0x100,
 	.map_io	      = davinci_sffsdr_map_io,
 	.init_irq     = davinci_irq_init,
 	.timer	      = &davinci_timer,

arch/arm/mach-davinci/board-tnetv107x-evm.c

@@ -277,7 +277,7 @@ console_initcall(tnetv107x_evm_console_init);
 #endif
 
 MACHINE_START(TNETV107X, "TNETV107X EVM")
-	.boot_params	= (TNETV107X_DDR_BASE + 0x100),
+	.atag_offset	= 0x100,
 	.map_io		= tnetv107x_init,
 	.init_irq	= cp_intc_init,
 	.timer		= &davinci_timer,

arch/arm/mach-davinci/common.c

@@ -12,6 +12,7 @@
 #include <linux/io.h>
 #include <linux/etherdevice.h>
 #include <linux/davinci_emac.h>
+#include <linux/dma-mapping.h>
 
 #include <asm/tlb.h>
 #include <asm/mach/map.h>
@@ -86,6 +87,8 @@ void __init davinci_common_init(struct davinci_soc_info *soc_info)
 		iotable_init(davinci_soc_info.io_desc,
 				davinci_soc_info.io_desc_num);
 
+	init_consistent_dma_size(14 << 20);
+
 	/*
 	 * Normally devicemaps_init() would flush caches and tlb after
 	 * mdesc->map_io(), but we must also do it here because of the CPU

arch/arm/mach-davinci/cpuidle.c

@@ -19,7 +19,7 @@
 #include <asm/proc-fns.h>
 
 #include <mach/cpuidle.h>
-#include <mach/memory.h>
+#include <mach/ddr2.h>
 
 #define DAVINCI_CPUIDLE_MAX_STATES	2
 

arch/arm/mach-davinci/include/mach/ddr2.h

+#define DDR2_SDRCR_OFFSET	0xc
+#define DDR2_SRPD_BIT		(1 << 23)
+#define DDR2_MCLKSTOPEN_BIT	(1 << 30)
+#define DDR2_LPMODEN_BIT	(1 << 31)

arch/arm/mach-davinci/include/mach/debug-macro.S

@@ -18,56 +18,50 @@
 
 #include <linux/serial_reg.h>
 
-#include <asm/memory.h>
-
 #include <mach/serial.h>
 
 #define UART_SHIFT	2
 
-#define davinci_uart_v2p(x)	((x) - PAGE_OFFSET + PLAT_PHYS_OFFSET)
-#define davinci_uart_p2v(x)	((x) - PLAT_PHYS_OFFSET + PAGE_OFFSET)
-
 		.pushsection .data
 davinci_uart_phys:	.word	0
 davinci_uart_virt:	.word	0
 		.popsection
 
-		.macro addruart, rp, rv
+		.macro addruart, rp, rv, tmp
 
 		/* Use davinci_uart_phys/virt if already configured */
-10:		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
-		ldreq	\rp, =davinci_uart_v2p(davinci_uart_phys)
-		ldrne	\rp, =davinci_uart_phys
-		add	\rv, \rp, #4		@ davinci_uart_virt
-		ldr	\rp, [\rp, #0]
-		ldr	\rv, [\rv, #0]
+10:		adr	\rp, 99f		@ get effective addr of 99f
+		ldr	\rv, [\rp]		@ get absolute addr of 99f
+		sub	\rv, \rv, \rp		@ offset between the two
+		ldr	\rp, [\rp, #4]		@ abs addr of omap_uart_phys
+		sub	\tmp, \rp, \rv		@ make it effective
+		ldr	\rp, [\tmp, #0]		@ davinci_uart_phys
+		ldr	\rv, [\tmp, #4]		@ davinci_uart_virt
 		cmp	\rp, #0			@ is port configured?
 		cmpne	\rv, #0
-		bne	99f			@ already configured
+		bne	100f			@ already configured
 
 		/* Check the debug UART address set in uncompress.h */
-		mrc	p15, 0, \rp, c1, c0
-		tst	\rp, #1			@ MMU enabled?
+		and	\rp, pc, #0xff000000
+		ldr	\rv, =DAVINCI_UART_INFO_OFS
+		add	\rp, \rp, \rv
 
 		/* Copy uart phys address from decompressor uart info */
-		ldreq	\rv, =davinci_uart_v2p(davinci_uart_phys)
-		ldrne	\rv, =davinci_uart_phys
-		ldreq	\rp, =DAVINCI_UART_INFO
-		ldrne	\rp, =davinci_uart_p2v(DAVINCI_UART_INFO)
-		ldr	\rp, [\rp, #0]
-		str	\rp, [\rv]
+		ldr	\rv, [\rp, #0]
+		str	\rv, [\tmp, #0]
 
 		/* Copy uart virt address from decompressor uart info */
-		ldreq	\rv, =davinci_uart_v2p(davinci_uart_virt)
-		ldrne	\rv, =davinci_uart_virt
-		ldreq	\rp, =DAVINCI_UART_INFO
-		ldrne	\rp, =davinci_uart_p2v(DAVINCI_UART_INFO)
-		ldr	\rp, [\rp, #4]
-		str	\rp, [\rv]
+		ldr	\rv, [\rp, #4]
+		str	\rv, [\tmp, #4]
 
 		b	10b
-99:
+
+		.align
+99:		.word	.
+		.word	davinci_uart_phys
+		.ltorg
+
+100:
 		.endm
 
 		.macro	senduart,rd,rx

arch/arm/mach-davinci/include/mach/memory.h

-/*
- * DaVinci memory space definitions
- *
- * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/**************************************************************************
- * Included Files
- **************************************************************************/
-#include <asm/page.h>
-#include <asm/sizes.h>
-
-/**************************************************************************
- * Definitions
- **************************************************************************/
-#define DAVINCI_DDR_BASE	0x80000000
-#define DA8XX_DDR_BASE		0xc0000000
-
-#if defined(CONFIG_ARCH_DAVINCI_DA8XX) && defined(CONFIG_ARCH_DAVINCI_DMx)
-#error Cannot enable DaVinci and DA8XX platforms concurrently
-#elif defined(CONFIG_ARCH_DAVINCI_DA8XX)
-#define PLAT_PHYS_OFFSET DA8XX_DDR_BASE
-#else
-#define PLAT_PHYS_OFFSET DAVINCI_DDR_BASE
-#endif
-
-#define DDR2_SDRCR_OFFSET	0xc
-#define DDR2_SRPD_BIT		BIT(23)
-#define DDR2_MCLKSTOPEN_BIT	BIT(30)
-#define DDR2_LPMODEN_BIT	BIT(31)
-
-/*
- * Increase size of DMA-consistent memory region
- */
-#define CONSISTENT_DMA_SIZE (14<<20)
-
-#endif /* __ASM_ARCH_MEMORY_H */

arch/arm/mach-davinci/include/mach/serial.h

@@ -21,8 +21,9 @@
  * macros in debug-macro.S.
  *
  * This area sits just below the page tables (see arch/arm/kernel/head.S).
+ * We define it as a relative offset from start of usable RAM.
  */
-#define DAVINCI_UART_INFO	(PLAT_PHYS_OFFSET + 0x3ff8)
+#define DAVINCI_UART_INFO_OFS	0x3ff8
 
 #define DAVINCI_UART0_BASE	(IO_PHYS + 0x20000)
 #define DAVINCI_UART1_BASE	(IO_PHYS + 0x20400)

arch/arm/mach-davinci/include/mach/uncompress.h

@@ -43,7 +43,12 @@ static inline void flush(void)
 
 static inline void set_uart_info(u32 phys, void * __iomem virt)
 {
-	u32 *uart_info = (u32 *)(DAVINCI_UART_INFO);
+	/*
+	 * Get address of some.bss variable and round it down
+	 * a la CONFIG_AUTO_ZRELADDR.
+	 */
+	u32 ram_start = (u32)&uart & 0xf8000000;
+	u32 *uart_info = (u32 *)(ram_start + DAVINCI_UART_INFO_OFS);
 
 	uart = (u32 *)phys;
 	uart_info[0] = phys;

arch/arm/mach-davinci/sleep.S

@@ -22,7 +22,7 @@
 #include <linux/linkage.h>
 #include <asm/assembler.h>
 #include <mach/psc.h>
-#include <mach/memory.h>
+#include <mach/ddr2.h>
 
 #include "clock.h"
 

arch/arm/mach-dove/cm-a510.c

@@ -87,7 +87,7 @@ static void __init cm_a510_init(void)
 }
 
 MACHINE_START(CM_A510, "Compulab CM-A510 Board")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= cm_a510_init,
 	.map_io		= dove_map_io,
 	.init_early	= dove_init_early,

arch/arm/mach-dove/dove-db-setup.c

@@ -94,7 +94,7 @@ static void __init dove_db_init(void)
 }
 
 MACHINE_START(DOVE_DB, "Marvell DB-MV88AP510-BP Development Board")
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.init_machine	= dove_db_init,
 	.map_io		= dove_map_io,
 	.init_early	= dove_init_early,

arch/arm/mach-dove/include/mach/debug-macro.S

@@ -8,7 +8,7 @@
 
 #include <mach/bridge-regs.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =DOVE_SB_REGS_PHYS_BASE
 	ldr	\rv, =DOVE_SB_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000

arch/arm/mach-dove/include/mach/memory.h

-/*
- * arch/arm/mach-dove/include/mach/memory.h
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET		UL(0x00000000)
-
-#endif

arch/arm/mach-ebsa110/core.c

@@ -280,7 +280,7 @@ arch_initcall(ebsa110_init);
 
 MACHINE_START(EBSA110, "EBSA110")
 	/* Maintainer: Russell King */
-	.boot_params	= 0x00000400,
+	.atag_offset	= 0x400,
 	.reserve_lp0	= 1,
 	.reserve_lp2	= 1,
 	.soft_reboot	= 1,

arch/arm/mach-ebsa110/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 **/
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0xf0000000
 		orr	\rp, \rp, #0x00000be0
 		mov	\rp, \rv

arch/arm/mach-ep93xx/adssphere.c

@@ -33,7 +33,7 @@ static void __init adssphere_init_machine(void)
 
 MACHINE_START(ADSSPHERE, "ADS Sphere board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,

arch/arm/mach-ep93xx/edb93xx.c

@@ -240,7 +240,7 @@ static void __init edb93xx_init_machine(void)
 #ifdef CONFIG_MACH_EDB9301
 MACHINE_START(EDB9301, "Cirrus Logic EDB9301 Evaluation Board")
 	/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -251,7 +251,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_EDB9302
 MACHINE_START(EDB9302, "Cirrus Logic EDB9302 Evaluation Board")
 	/* Maintainer: George Kashperko <george@chas.com.ua> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -262,7 +262,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_EDB9302A
 MACHINE_START(EDB9302A, "Cirrus Logic EDB9302A Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -273,7 +273,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_EDB9307
 MACHINE_START(EDB9307, "Cirrus Logic EDB9307 Evaluation Board")
 	/* Maintainer: Herbert Valerio Riedel <hvr@gnu.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -284,7 +284,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_EDB9307A
 MACHINE_START(EDB9307A, "Cirrus Logic EDB9307A Evaluation Board")
 	/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -295,7 +295,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_EDB9312
 MACHINE_START(EDB9312, "Cirrus Logic EDB9312 Evaluation Board")
 	/* Maintainer: Toufeeq Hussain <toufeeq_hussain@infosys.com> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -306,7 +306,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_EDB9315
 MACHINE_START(EDB9315, "Cirrus Logic EDB9315 Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -317,7 +317,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_EDB9315A
 MACHINE_START(EDB9315A, "Cirrus Logic EDB9315A Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,

arch/arm/mach-ep93xx/gesbc9312.c

@@ -33,7 +33,7 @@ static void __init gesbc9312_init_machine(void)
 
 MACHINE_START(GESBC9312, "Glomation GESBC-9312-sx")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,

arch/arm/mach-ep93xx/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  */
 #include <mach/ep93xx-regs.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =EP93XX_APB_PHYS_BASE	@ Physical base
 		ldr	\rv, =EP93XX_APB_VIRT_BASE	@ virtual base
 		orr	\rp, \rp, #0x000c0000

arch/arm/mach-ep93xx/micro9.c

@@ -77,7 +77,7 @@ static void __init micro9_init_machine(void)
 #ifdef CONFIG_MACH_MICRO9H
 MACHINE_START(MICRO9, "Contec Micro9-High")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -88,7 +88,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_MICRO9M
 MACHINE_START(MICRO9M, "Contec Micro9-Mid")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_ASYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -99,7 +99,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_MICRO9L
 MACHINE_START(MICRO9L, "Contec Micro9-Lite")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,
@@ -110,7 +110,7 @@ MACHINE_END
 #ifdef CONFIG_MACH_MICRO9S
 MACHINE_START(MICRO9S, "Contec Micro9-Slim")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_ASYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,

arch/arm/mach-ep93xx/simone.c

@@ -65,8 +65,8 @@ static void __init simone_init_machine(void)
 }
 
 MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board")
-/* Maintainer: Ryan Mallon */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	/* Maintainer: Ryan Mallon */
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,

arch/arm/mach-ep93xx/snappercl15.c

@@ -163,7 +163,7 @@ static void __init snappercl15_init_machine(void)
 
 MACHINE_START(SNAPPER_CL15, "Bluewater Systems Snapper CL15")
 	/* Maintainer: Ryan Mallon */
-	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer 		= &ep93xx_timer,

arch/arm/mach-ep93xx/ts72xx.c

@@ -257,7 +257,7 @@ static void __init ts72xx_init_machine(void)
 
 MACHINE_START(TS72XX, "Technologic Systems TS-72xx SBC")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
-	.boot_params	= EP93XX_SDCE3_PHYS_BASE_SYNC + 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= ts72xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.timer		= &ep93xx_timer,

arch/arm/mach-exynos4/include/mach/debug-macro.S

@@ -20,7 +20,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = S3C_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0

arch/arm/mach-exynos4/mach-armlex4210.c

@@ -207,7 +207,7 @@ static void __init armlex4210_machine_init(void)
 
 MACHINE_START(ARMLEX4210, "ARMLEX4210")
 	/* Maintainer: Alim Akhtar <alim.akhtar@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= exynos4_init_irq,
 	.map_io		= armlex4210_map_io,
 	.init_machine	= armlex4210_machine_init,

arch/arm/mach-exynos4/mach-nuri.c

@@ -1186,7 +1186,7 @@ static void __init nuri_machine_init(void)
 
 MACHINE_START(NURI, "NURI")
 	/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= exynos4_init_irq,
 	.map_io		= nuri_map_io,
 	.init_machine	= nuri_machine_init,

arch/arm/mach-exynos4/mach-universal_c210.c

@@ -1055,7 +1055,7 @@ static void __init universal_machine_init(void)
 
 MACHINE_START(UNIVERSAL_C210, "UNIVERSAL_C210")
 	/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
-	.boot_params	= S5P_PA_SDRAM + 0x100,
+	.atag_offset	= 0x100,
 	.init_irq	= exynos4_init_irq,
 	.map_io		= universal_map_io,
 	.init_machine	= universal_machine_init,

arch/arm/mach-footbridge/cats-hw.c

@@ -86,7 +86,7 @@ fixup_cats(struct machine_desc *desc, struct tag *tags,
 
 MACHINE_START(CATS, "Chalice-CATS")
 	/* Maintainer: Philip Blundell */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.soft_reboot	= 1,
 	.fixup		= fixup_cats,
 	.map_io		= footbridge_map_io,

arch/arm/mach-footbridge/ebsa285.c

@@ -15,7 +15,7 @@
 
 MACHINE_START(EBSA285, "EBSA285")
 	/* Maintainer: Russell King */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.video_start	= 0x000a0000,
 	.video_end	= 0x000bffff,
 	.map_io		= footbridge_map_io,

arch/arm/mach-footbridge/include/mach/debug-macro.S

@@ -15,7 +15,7 @@
 
 #ifndef CONFIG_DEBUG_DC21285_PORT
 	/* For NetWinder debugging */
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x000003f8
 		orr	\rv, \rp, #0xff000000	@ virtual
 		orr	\rp, \rp, #0x7c000000	@ physical
@@ -31,7 +31,7 @@
 		.equ	dc21285_high, ARMCSR_BASE & 0xff000000
 		.equ	dc21285_low,  ARMCSR_BASE & 0x00ffffff
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		.if	dc21285_low
 		mov	\rp, #dc21285_low
 		.else

arch/arm/mach-footbridge/netwinder-hw.c

@@ -648,7 +648,7 @@ fixup_netwinder(struct machine_desc *desc, struct tag *tags,
 
 MACHINE_START(NETWINDER, "Rebel-NetWinder")
 	/* Maintainer: Russell King/Rebel.com */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.video_start	= 0x000a0000,
 	.video_end	= 0x000bffff,
 	.reserve_lp0	= 1,

arch/arm/mach-footbridge/personal.c

@@ -15,7 +15,7 @@
 
 MACHINE_START(PERSONAL_SERVER, "Compaq-PersonalServer")
 	/* Maintainer: Jamey Hicks / George France */
-	.boot_params	= 0x00000100,
+	.atag_offset	= 0x100,
 	.map_io		= footbridge_map_io,
 	.init_irq	= footbridge_init_irq,
 	.timer		= &footbridge_timer,

arch/arm/mach-gemini/board-nas4220b.c

@@ -102,7 +102,7 @@ static void __init ib4220b_init(void)
 }
 
 MACHINE_START(NAS4220B, "Raidsonic NAS IB-4220-B")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gemini_map_io,
 	.init_irq	= gemini_init_irq,
 	.timer		= &ib4220b_timer,

arch/arm/mach-gemini/board-rut1xx.c

@@ -86,7 +86,7 @@ static void __init rut1xx_init(void)
 }
 
 MACHINE_START(RUT100, "Teltonika RUT100")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gemini_map_io,
 	.init_irq	= gemini_init_irq,
 	.timer		= &rut1xx_timer,

arch/arm/mach-gemini/board-wbd111.c

@@ -129,7 +129,7 @@ static void __init wbd111_init(void)
 }
 
 MACHINE_START(WBD111, "Wiliboard WBD-111")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gemini_map_io,
 	.init_irq	= gemini_init_irq,
 	.timer		= &wbd111_timer,

arch/arm/mach-gemini/board-wbd222.c

@@ -129,7 +129,7 @@ static void __init wbd222_init(void)
 }
 
 MACHINE_START(WBD222, "Wiliboard WBD-222")
-	.boot_params	= 0x100,
+	.atag_offset	= 0x100,
 	.map_io		= gemini_map_io,
 	.init_irq	= gemini_init_irq,
 	.timer		= &wbd222_timer,

arch/arm/mach-gemini/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  */
 #include <mach/hardware.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =GEMINI_UART_BASE			@ physical
 	ldr	\rv, =IO_ADDRESS(GEMINI_UART_BASE)	@ virtual
 	.endm

arch/arm/mach-gemini/include/mach/memory.h

-/*
- *  Copyright (C) 2001-2006 Storlink, Corp.
- *  Copyright (C) 2008-2009 Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#ifndef __MACH_MEMORY_H
-#define __MACH_MEMORY_H
-
-#ifdef CONFIG_GEMINI_MEM_SWAP
-# define PLAT_PHYS_OFFSET	UL(0x00000000)
-#else
-# define PLAT_PHYS_OFFSET	UL(0x10000000)
-#endif
-
-#endif /* __MACH_MEMORY_H */

arch/arm/mach-h720x/h7201-eval.c

@@ -29,7 +29,7 @@
 
 MACHINE_START(H7201, "Hynix GMS30C7201")
 	/* Maintainer: Robert Schwebel, Pengutronix */
-	.boot_params	= 0xc0001000,
+	.atag_offset	= 0x1000,
 	.map_io		= h720x_map_io,
 	.init_irq	= h720x_init_irq,
 	.timer		= &h7201_timer,

arch/arm/mach-h720x/h7202-eval.c

@@ -71,7 +71,7 @@ static void __init init_eval_h7202(void)
 
 MACHINE_START(H7202, "Hynix HMS30C7202")
 	/* Maintainer: Robert Schwebel, Pengutronix */
-	.boot_params	= 0x40000100,
+	.atag_offset	= 0x100,
 	.map_io		= h720x_map_io,
 	.init_irq	= h7202_init_irq,
 	.timer		= &h7202_timer,

arch/arm/mach-h720x/include/mach/debug-macro.S

@@ -16,7 +16,7 @@
 		.equ    io_virt, IO_VIRT
 		.equ    io_phys, IO_PHYS
 
-		.macro  addruart, rp, rv
+		.macro  addruart, rp, rv, tmp
 		mov     \rp, #0x00020000	@ UART1
 		add     \rv, \rp, #io_virt	@ virtual address
 		add     \rp, \rp, #io_phys	@ physical base address

arch/arm/mach-h720x/include/mach/memory.h

-/*
- * arch/arm/mach-h720x/include/mach/memory.h
- *
- * Copyright (c) 2000 Jungjun Kim
- *
- */
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET	UL(0x40000000)
-#endif

arch/arm/mach-imx/mach-armadillo5x0.c

@@ -558,7 +558,7 @@ static struct sys_timer armadillo5x0_timer = {
 
 MACHINE_START(ARMADILLO5X0, "Armadillo-500")
 	/* Maintainer: Alberto Panizzo  */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,

arch/arm/mach-imx/mach-cpuimx27.c

@@ -311,7 +311,7 @@ static struct sys_timer eukrea_cpuimx27_timer = {
 };
 
 MACHINE_START(EUKREA_CPUIMX27, "EUKREA CPUIMX27")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,

arch/arm/mach-imx/mach-cpuimx35.c

@@ -194,7 +194,7 @@ struct sys_timer eukrea_cpuimx35_timer = {
 
 MACHINE_START(EUKREA_CPUIMX35SD, "Eukrea CPUIMX35")
 	/* Maintainer: Eukrea Electromatique */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx35_map_io,
 	.init_early = imx35_init_early,
 	.init_irq = mx35_init_irq,

arch/arm/mach-imx/mach-eukrea_cpuimx25.c

@@ -163,7 +163,7 @@ static struct sys_timer eukrea_cpuimx25_timer = {
 
 MACHINE_START(EUKREA_CPUIMX25SD, "Eukrea CPUIMX25")
 	/* Maintainer: Eukrea Electromatique */
-	.boot_params = MX25_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx25_map_io,
 	.init_early = imx25_init_early,
 	.init_irq = mx25_init_irq,

arch/arm/mach-imx/mach-imx27_visstrim_m10.c

@@ -275,7 +275,7 @@ static struct sys_timer visstrim_m10_timer = {
 };
 
 MACHINE_START(IMX27_VISSTRIM_M10, "Vista Silicon Visstrim_M10")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,

arch/arm/mach-imx/mach-imx27ipcam.c

@@ -71,7 +71,7 @@ static struct sys_timer mx27ipcam_timer = {
 
 MACHINE_START(IMX27IPCAM, "Freescale IMX27IPCAM")
 	/* maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,

arch/arm/mach-imx/mach-imx27lite.c

@@ -77,7 +77,7 @@ static struct sys_timer mx27lite_timer = {
 };
 
 MACHINE_START(IMX27LITE, "LogicPD i.MX27LITE")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,

arch/arm/mach-imx/mach-kzm_arm11_01.c

@@ -271,7 +271,7 @@ static struct sys_timer kzm_timer = {
 };
 
 MACHINE_START(KZM_ARM11_01, "Kyoto Microcomputer Co., Ltd. KZM-ARM11-01")
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = kzm_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,

arch/arm/mach-imx/mach-mx1ads.c

@@ -145,7 +145,7 @@ struct sys_timer mx1ads_timer = {
 
 MACHINE_START(MX1ADS, "Freescale MX1ADS")
 	/* Maintainer: Sascha Hauer, Pengutronix */
-	.boot_params = MX1_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx1_map_io,
 	.init_early = imx1_init_early,
 	.init_irq = mx1_init_irq,
@@ -154,7 +154,7 @@ MACHINE_START(MX1ADS, "Freescale MX1ADS")
 MACHINE_END
 
 MACHINE_START(MXLADS, "Freescale MXLADS")
-	.boot_params = MX1_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx1_map_io,
 	.init_early = imx1_init_early,
 	.init_irq = mx1_init_irq,

arch/arm/mach-imx/mach-mx21ads.c

@@ -305,7 +305,7 @@ static struct sys_timer mx21ads_timer = {
 
 MACHINE_START(MX21ADS, "Freescale i.MX21ADS")
 	/* maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX21_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx21ads_map_io,
 	.init_early = imx21_init_early,
 	.init_irq = mx21_init_irq,

arch/arm/mach-imx/mach-mx25_3ds.c

@@ -253,7 +253,7 @@ static struct sys_timer mx25pdk_timer = {
 
 MACHINE_START(MX25_3DS, "Freescale MX25PDK (3DS)")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX25_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx25_map_io,
 	.init_early = imx25_init_early,
 	.init_irq = mx25_init_irq,

arch/arm/mach-imx/mach-mx27_3ds.c

@@ -421,7 +421,7 @@ static struct sys_timer mx27pdk_timer = {
 
 MACHINE_START(MX27_3DS, "Freescale MX27PDK")
 	/* maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,

arch/arm/mach-imx/mach-mx27ads.c

@@ -345,7 +345,7 @@ static void __init mx27ads_map_io(void)
 
 MACHINE_START(MX27ADS, "Freescale i.MX27ADS")
 	/* maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27ads_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,

arch/arm/mach-imx/mach-mx31_3ds.c

@@ -764,7 +764,7 @@ static void __init mx31_3ds_reserve(void)
 
 MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,

arch/arm/mach-imx/mach-mx31ads.c

@@ -535,7 +535,7 @@ static struct sys_timer mx31ads_timer = {
 
 MACHINE_START(MX31ADS, "Freescale MX31ADS")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31ads_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31ads_init_irq,

arch/arm/mach-imx/mach-mx31lilly.c

@@ -295,7 +295,7 @@ static struct sys_timer mx31lilly_timer = {
 };
 
 MACHINE_START(LILLY1131, "INCO startec LILLY-1131")
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,

arch/arm/mach-imx/mach-mx31lite.c

@@ -280,7 +280,7 @@ struct sys_timer mx31lite_timer = {
 
 MACHINE_START(MX31LITE, "LogicPD i.MX31 SOM")
 	/* Maintainer: Freescale Semiconductor, Inc. */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx31lite_map_io,
 	.init_early = imx31_init_early,
 	.init_irq = mx31_init_irq,

arch/arm/mach-imx/mach-mx31moboard.c

@@ -567,7 +567,7 @@ static void __init mx31moboard_reserve(void)
 
 MACHINE_START(MX31MOBOARD, "EPFL Mobots mx31moboard")
 	/* Maintainer: Valentin Longchamp, EPFL Mobots group */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.reserve = mx31moboard_reserve,
 	.map_io = mx31_map_io,
 	.init_early = imx31_init_early,

arch/arm/mach-imx/mach-mx35_3ds.c

@@ -217,7 +217,7 @@ struct sys_timer mx35pdk_timer = {
 
 MACHINE_START(MX35_3DS, "Freescale MX35PDK")
 	/* Maintainer: Freescale Semiconductor, Inc */
-	.boot_params = MX3x_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx35_map_io,
 	.init_early = imx35_init_early,
 	.init_irq = mx35_init_irq,

arch/arm/mach-imx/mach-mxt_td60.c

@@ -267,7 +267,7 @@ static struct sys_timer mxt_td60_timer = {
 
 MACHINE_START(MXT_TD60, "Maxtrack i-MXT TD60")
 	/* maintainer: Maxtrack Industrial */
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,

arch/arm/mach-imx/mach-pca100.c

@@ -435,7 +435,7 @@ static struct sys_timer pca100_timer = {
 };
 
 MACHINE_START(PCA100, "phyCARD-i.MX27")
-	.boot_params = MX27_PHYS_OFFSET + 0x100,
+	.atag_offset = 0x100,
 	.map_io = mx27_map_io,
 	.init_early = imx27_init_early,
 	.init_irq = mx27_init_irq,