Merge branch 'Lantiq-Intel-vrx200-support'

Hauke Mehrtens says:

====================
Add support for Lantiq / Intel vrx200 network

This adds basic support for the GSWIP (Gigabit Switch) found in the
VRX200 SoC.
There are different versions of this IP core used in different SoCs, but
this driver was currently only tested on the VRX200 SoC line, for other
SoCs this driver probably need some adoptions to work.

I also plan to add Layer 2 offloading to the DSA driver and later also
layer 3 offloading which is supported by the PPE HW block.

All these patches should go through the net-next tree.

This depends on the patch "MIPS: lantiq: dma: add dev pointer" which
should go into 4.19.

Changes since:
v2:
 * Send patch "MIPS: lantiq: dma: add dev pointer" separately
 * all: removed return in register write functions
 * switch: uses phylink
 * switch: uses hardware MDIO auto polling
 * switch: use usleep_range() in MDIO busy check
 * switch: configure MDIO bus to 2.5 MHz
 * switch: disable xMII link when it is not used
 * Ethernet: use NAPI for TX cleanups
 * Ethernet: enable clock in open callback
 * Ethernet: improve skb allocation
 * Ethernet: use net_dev->stats

v1:
 * Add "MIPS: lantiq: dma: add dev pointer"
 * checkpatch fixes a all patches
 * Added binding documentation
 * use readx_poll_timeout function and ETIMEOUT error code
 * integrate GPHY firmware loading into DSA driver
 * renamed to NET_DSA_LANTIQ_GSWIP
 * removed some needed casts
 * added of_device_id.data information about the detected switch
 * fixed John's email address
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/dsa/lantiq-gswip.txt

+Lantiq GSWIP Ethernet switches
+==================================
+
+Required properties for GSWIP core:
+
+- compatible	: "lantiq,xrx200-gswip" for the embedded GSWIP in the
+		  xRX200 SoC
+- reg		: memory range of the GSWIP core registers
+		: memory range of the GSWIP MDIO registers
+		: memory range of the GSWIP MII registers
+
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of
+additional required and optional properties.
+
+
+Required properties for MDIO bus:
+- compatible	: "lantiq,xrx200-mdio" for the MDIO bus inside the GSWIP
+		  core of the xRX200 SoC and the PHYs connected to it.
+
+See Documentation/devicetree/bindings/net/mdio.txt for a list of additional
+required and optional properties.
+
+
+Required properties for GPHY firmware loading:
+- compatible	: "lantiq,gphy-fw" and "lantiq,xrx200-gphy-fw",
+		  "lantiq,xrx200a1x-gphy-fw", "lantiq,xrx200a2x-gphy-fw",
+		  "lantiq,xrx300-gphy-fw", or "lantiq,xrx330-gphy-fw"
+		  for the loading of the firmware into the embedded
+		  GPHY core of the SoC.
+- lantiq,rcu	: reference to the rcu syscon
+
+The GPHY firmware loader has a list of GPHY entries, one for each
+embedded GPHY
+
+- reg		: Offset of the GPHY firmware register in the RCU
+		  register range
+- resets	: list of resets of the embedded GPHY
+- reset-names	: list of names of the resets
+
+Example:
+
+Ethernet switch on the VRX200 SoC:
+
+gswip: gswip@E108000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "lantiq,xrx200-gswip";
+	reg = <	0xE108000 0x3000 /* switch */
+		0xE10B100 0x70 /* mdio */
+		0xE10B1D8 0x30 /* mii */
+		>;
+	dsa,member = <0 0>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan3";
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan4";
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+			phy-mode = "internal";
+			phy-handle = <&phy11>;
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan1";
+			phy-mode = "internal";
+			phy-handle = <&phy13>;
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "wan";
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+		};
+
+		port@6 {
+			reg = <0x6>;
+			label = "cpu";
+			ethernet = <&eth0>;
+		};
+	};
+
+	mdio@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "lantiq,xrx200-mdio";
+		reg = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0x0>;
+		};
+		phy1: ethernet-phy@1 {
+			reg = <0x1>;
+		};
+		phy5: ethernet-phy@5 {
+			reg = <0x5>;
+		};
+		phy11: ethernet-phy@11 {
+			reg = <0x11>;
+		};
+		phy13: ethernet-phy@13 {
+			reg = <0x13>;
+		};
+	};
+
+	gphy-fw {
+		compatible = "lantiq,xrx200-gphy-fw", "lantiq,gphy-fw";
+		lantiq,rcu = <&rcu0>;
+
+		gphy@20 {
+			reg = <0x20>;
+
+			resets = <&reset0 31 30>;
+			reset-names = "gphy";
+		};
+
+		gphy@68 {
+			reg = <0x68>;
+
+			resets = <&reset0 29 28>;
+			reset-names = "gphy";
+		};
+	};
+};

Documentation/devicetree/bindings/net/lantiq,xrx200-net.txt

+Lantiq xRX200 GSWIP PMAC Ethernet driver
+==================================
+
+Required properties:
+
+- compatible	: "lantiq,xrx200-net" for the PMAC of the embedded
+		: GSWIP in the xXR200
+- reg		: memory range of the PMAC core inside of the GSWIP core
+- interrupts	: TX and RX DMA interrupts. Use interrupt-names "tx" for
+		: the TX interrupt and "rx" for the RX interrupt.
+
+Example:
+
+eth0: eth@E10B308 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "lantiq,xrx200-net";
+	reg = <0xE10B308 0x30>;
+	interrupts = <73>, <72>;
+	interrupt-names = "tx", "rx";
+};

MAINTAINERS

@@ -8167,6 +8167,15 @@ S:	Maintained
 F:	net/l3mdev
 F:	include/net/l3mdev.h
 
+LANTIQ / INTEL Ethernet drivers
+M:	Hauke Mehrtens <hauke@hauke-m.de>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	net/dsa/tag_gswip.c
+F:	drivers/net/ethernet/lantiq_xrx200.c
+F:	drivers/net/dsa/lantiq_pce.h
+F:	drivers/net/dsa/intel_gswip.c
+
 LANTIQ MIPS ARCHITECTURE
 M:	John Crispin <john@phrozen.org>
 L:	linux-mips@linux-mips.org

arch/mips/lantiq/xway/dma.c

@@ -106,7 +106,6 @@ ltq_dma_open(struct ltq_dma_channel *ch)
 	spin_lock_irqsave(&ltq_dma_lock, flag);
 	ltq_dma_w32(ch->nr, LTQ_DMA_CS);
 	ltq_dma_w32_mask(0, DMA_CHAN_ON, LTQ_DMA_CCTRL);
-	ltq_dma_w32_mask(0, 1 << ch->nr, LTQ_DMA_IRNEN);
 	spin_unlock_irqrestore(&ltq_dma_lock, flag);
 }
 EXPORT_SYMBOL_GPL(ltq_dma_open);

arch/mips/lantiq/xway/sysctrl.c

@@ -505,7 +505,7 @@ void __init ltq_soc_init(void)
 		clkdev_add_pmu("1a800000.pcie", "msi", 1, 1, PMU1_PCIE2_MSI);
 		clkdev_add_pmu("1a800000.pcie", "pdi", 1, 1, PMU1_PCIE2_PDI);
 		clkdev_add_pmu("1a800000.pcie", "ctl", 1, 1, PMU1_PCIE2_CTL);
-		clkdev_add_pmu("1e108000.eth", NULL, 0, 0, PMU_SWITCH | PMU_PPE_DP);
+		clkdev_add_pmu("1e10b308.eth", NULL, 0, 0, PMU_SWITCH | PMU_PPE_DP);
 		clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
 		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
 	} else if (of_machine_is_compatible("lantiq,ar10")) {
@@ -513,11 +513,11 @@ void __init ltq_soc_init(void)
 				  ltq_ar10_fpi_hz(), ltq_ar10_pp32_hz());
 		clkdev_add_pmu("1e101000.usb", "otg", 1, 0, PMU_USB0);
 		clkdev_add_pmu("1e106000.usb", "otg", 1, 0, PMU_USB1);
-		clkdev_add_pmu("1e108000.eth", NULL, 0, 0, PMU_SWITCH |
+		clkdev_add_pmu("1e10b308.eth", NULL, 0, 0, PMU_SWITCH |
 			       PMU_PPE_DP | PMU_PPE_TC);
 		clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
-		clkdev_add_pmu("1f203020.gphy", NULL, 1, 0, PMU_GPHY);
-		clkdev_add_pmu("1f203068.gphy", NULL, 1, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.gswip", "gphy0", 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.gswip", "gphy1", 0, 0, PMU_GPHY);
 		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
 		clkdev_add_pmu("1e116000.mei", "afe", 1, 2, PMU_ANALOG_DSL_AFE);
 		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
@@ -536,12 +536,12 @@ void __init ltq_soc_init(void)
 		clkdev_add_pmu(NULL, "ahb", 1, 0, PMU_AHBM | PMU_AHBS);
 
 		clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
-		clkdev_add_pmu("1e108000.eth", NULL, 0, 0,
+		clkdev_add_pmu("1e10b308.eth", NULL, 0, 0,
 				PMU_SWITCH | PMU_PPE_DPLUS | PMU_PPE_DPLUM |
 				PMU_PPE_EMA | PMU_PPE_TC | PMU_PPE_SLL01 |
 				PMU_PPE_QSB | PMU_PPE_TOP);
-		clkdev_add_pmu("1f203020.gphy", NULL, 0, 0, PMU_GPHY);
-		clkdev_add_pmu("1f203068.gphy", NULL, 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.gswip", "gphy0", 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.gswip", "gphy1", 0, 0, PMU_GPHY);
 		clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
 		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
 		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);

drivers/net/dsa/Kconfig

@@ -23,6 +23,14 @@ config NET_DSA_LOOP
 	  This enables support for a fake mock-up switch chip which
 	  exercises the DSA APIs.
 
+config NET_DSA_LANTIQ_GSWIP
+	tristate "Lantiq / Intel GSWIP"
+	depends on NET_DSA
+	select NET_DSA_TAG_GSWIP
+	---help---
+	  This enables support for the Lantiq / Intel GSWIP 2.1 found in
+	  the xrx200 / VR9 SoC.
+
 config NET_DSA_MT7530
 	tristate "Mediatek MT7530 Ethernet switch support"
 	depends on NET_DSA

drivers/net/dsa/Makefile

@@ -5,6 +5,7 @@ obj-$(CONFIG_NET_DSA_LOOP)	+= dsa_loop.o
 ifdef CONFIG_NET_DSA_LOOP
 obj-$(CONFIG_FIXED_PHY)		+= dsa_loop_bdinfo.o
 endif
+obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
 obj-$(CONFIG_NET_DSA_MT7530)	+= mt7530.o
 obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
 obj-$(CONFIG_NET_DSA_QCA8K)	+= qca8k.o

drivers/net/dsa/lantiq_gswip.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Lantiq / Intel GSWIP switch driver for VRX200 SoCs
+ *
+ * Copyright (C) 2010 Lantiq Deutschland
+ * Copyright (C) 2012 John Crispin <john@phrozen.org>
+ * Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <linux/clk.h>
+#include <linux/etherdevice.h>
+#include <linux/firmware.h>
+#include <linux/if_bridge.h>
+#include <linux/if_vlan.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/phylink.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <net/dsa.h>
+#include <dt-bindings/mips/lantiq_rcu_gphy.h>
+
+#include "lantiq_pce.h"
+
+/* GSWIP MDIO Registers */
+#define GSWIP_MDIO_GLOB			0x00
+#define  GSWIP_MDIO_GLOB_ENABLE		BIT(15)
+#define GSWIP_MDIO_CTRL			0x08
+#define  GSWIP_MDIO_CTRL_BUSY		BIT(12)
+#define  GSWIP_MDIO_CTRL_RD		BIT(11)
+#define  GSWIP_MDIO_CTRL_WR		BIT(10)
+#define  GSWIP_MDIO_CTRL_PHYAD_MASK	0x1f
+#define  GSWIP_MDIO_CTRL_PHYAD_SHIFT	5
+#define  GSWIP_MDIO_CTRL_REGAD_MASK	0x1f
+#define GSWIP_MDIO_READ			0x09
+#define GSWIP_MDIO_WRITE		0x0A
+#define GSWIP_MDIO_MDC_CFG0		0x0B
+#define GSWIP_MDIO_MDC_CFG1		0x0C
+#define GSWIP_MDIO_PHYp(p)		(0x15 - (p))
+#define  GSWIP_MDIO_PHY_LINK_MASK	0x6000
+#define  GSWIP_MDIO_PHY_LINK_AUTO	0x0000
+#define  GSWIP_MDIO_PHY_LINK_DOWN	0x4000
+#define  GSWIP_MDIO_PHY_LINK_UP		0x2000
+#define  GSWIP_MDIO_PHY_SPEED_MASK	0x1800
+#define  GSWIP_MDIO_PHY_SPEED_AUTO	0x1800
+#define  GSWIP_MDIO_PHY_SPEED_M10	0x0000
+#define  GSWIP_MDIO_PHY_SPEED_M100	0x0800
+#define  GSWIP_MDIO_PHY_SPEED_G1	0x1000
+#define  GSWIP_MDIO_PHY_FDUP_MASK	0x0600
+#define  GSWIP_MDIO_PHY_FDUP_AUTO	0x0000
+#define  GSWIP_MDIO_PHY_FDUP_EN		0x0200
+#define  GSWIP_MDIO_PHY_FDUP_DIS	0x0600
+#define  GSWIP_MDIO_PHY_FCONTX_MASK	0x0180
+#define  GSWIP_MDIO_PHY_FCONTX_AUTO	0x0000
+#define  GSWIP_MDIO_PHY_FCONTX_EN	0x0100
+#define  GSWIP_MDIO_PHY_FCONTX_DIS	0x0180
+#define  GSWIP_MDIO_PHY_FCONRX_MASK	0x0060
+#define  GSWIP_MDIO_PHY_FCONRX_AUTO	0x0000
+#define  GSWIP_MDIO_PHY_FCONRX_EN	0x0020
+#define  GSWIP_MDIO_PHY_FCONRX_DIS	0x0060
+#define  GSWIP_MDIO_PHY_ADDR_MASK	0x001f
+#define  GSWIP_MDIO_PHY_MASK		(GSWIP_MDIO_PHY_ADDR_MASK | \
+					 GSWIP_MDIO_PHY_FCONRX_MASK | \
+					 GSWIP_MDIO_PHY_FCONTX_MASK | \
+					 GSWIP_MDIO_PHY_LINK_MASK | \
+					 GSWIP_MDIO_PHY_SPEED_MASK | \
+					 GSWIP_MDIO_PHY_FDUP_MASK)
+
+/* GSWIP MII Registers */
+#define GSWIP_MII_CFG0			0x00
+#define GSWIP_MII_CFG1			0x02
+#define GSWIP_MII_CFG5			0x04
+#define  GSWIP_MII_CFG_EN		BIT(14)
+#define  GSWIP_MII_CFG_LDCLKDIS		BIT(12)
+#define  GSWIP_MII_CFG_MODE_MIIP	0x0
+#define  GSWIP_MII_CFG_MODE_MIIM	0x1
+#define  GSWIP_MII_CFG_MODE_RMIIP	0x2
+#define  GSWIP_MII_CFG_MODE_RMIIM	0x3
+#define  GSWIP_MII_CFG_MODE_RGMII	0x4
+#define  GSWIP_MII_CFG_MODE_MASK	0xf
+#define  GSWIP_MII_CFG_RATE_M2P5	0x00
+#define  GSWIP_MII_CFG_RATE_M25	0x10
+#define  GSWIP_MII_CFG_RATE_M125	0x20
+#define  GSWIP_MII_CFG_RATE_M50	0x30
+#define  GSWIP_MII_CFG_RATE_AUTO	0x40
+#define  GSWIP_MII_CFG_RATE_MASK	0x70
+#define GSWIP_MII_PCDU0			0x01
+#define GSWIP_MII_PCDU1			0x03
+#define GSWIP_MII_PCDU5			0x05
+#define  GSWIP_MII_PCDU_TXDLY_MASK	GENMASK(2, 0)
+#define  GSWIP_MII_PCDU_RXDLY_MASK	GENMASK(9, 7)
+
+/* GSWIP Core Registers */
+#define GSWIP_SWRES			0x000
+#define  GSWIP_SWRES_R1			BIT(1)	/* GSWIP Software reset */
+#define  GSWIP_SWRES_R0			BIT(0)	/* GSWIP Hardware reset */
+#define GSWIP_VERSION			0x013
+#define  GSWIP_VERSION_REV_SHIFT	0
+#define  GSWIP_VERSION_REV_MASK		GENMASK(7, 0)
+#define  GSWIP_VERSION_MOD_SHIFT	8
+#define  GSWIP_VERSION_MOD_MASK		GENMASK(15, 8)
+#define   GSWIP_VERSION_2_0		0x100
+#define   GSWIP_VERSION_2_1		0x021
+#define   GSWIP_VERSION_2_2		0x122
+#define   GSWIP_VERSION_2_2_ETC		0x022
+
+#define GSWIP_BM_RAM_VAL(x)		(0x043 - (x))
+#define GSWIP_BM_RAM_ADDR		0x044
+#define GSWIP_BM_RAM_CTRL		0x045
+#define  GSWIP_BM_RAM_CTRL_BAS		BIT(15)
+#define  GSWIP_BM_RAM_CTRL_OPMOD	BIT(5)
+#define  GSWIP_BM_RAM_CTRL_ADDR_MASK	GENMASK(4, 0)
+#define GSWIP_BM_QUEUE_GCTRL		0x04A
+#define  GSWIP_BM_QUEUE_GCTRL_GL_MOD	BIT(10)
+/* buffer management Port Configuration Register */
+#define GSWIP_BM_PCFGp(p)		(0x080 + ((p) * 2))
+#define  GSWIP_BM_PCFG_CNTEN		BIT(0)	/* RMON Counter Enable */
+#define  GSWIP_BM_PCFG_IGCNT		BIT(1)	/* Ingres Special Tag RMON count */
+/* buffer management Port Control Register */
+#define GSWIP_BM_RMON_CTRLp(p)		(0x81 + ((p) * 2))
+#define  GSWIP_BM_CTRL_RMON_RAM1_RES	BIT(0)	/* Software Reset for RMON RAM 1 */
+#define  GSWIP_BM_CTRL_RMON_RAM2_RES	BIT(1)	/* Software Reset for RMON RAM 2 */
+
+/* PCE */
+#define GSWIP_PCE_TBL_KEY(x)		(0x447 - (x))
+#define GSWIP_PCE_TBL_MASK		0x448
+#define GSWIP_PCE_TBL_VAL(x)		(0x44D - (x))
+#define GSWIP_PCE_TBL_ADDR		0x44E
+#define GSWIP_PCE_TBL_CTRL		0x44F
+#define  GSWIP_PCE_TBL_CTRL_BAS		BIT(15)
+#define  GSWIP_PCE_TBL_CTRL_TYPE	BIT(13)
+#define  GSWIP_PCE_TBL_CTRL_VLD		BIT(12)
+#define  GSWIP_PCE_TBL_CTRL_KEYFORM	BIT(11)
+#define  GSWIP_PCE_TBL_CTRL_GMAP_MASK	GENMASK(10, 7)
+#define  GSWIP_PCE_TBL_CTRL_OPMOD_MASK	GENMASK(6, 5)
+#define  GSWIP_PCE_TBL_CTRL_OPMOD_ADRD	0x00
+#define  GSWIP_PCE_TBL_CTRL_OPMOD_ADWR	0x20
+#define  GSWIP_PCE_TBL_CTRL_OPMOD_KSRD	0x40
+#define  GSWIP_PCE_TBL_CTRL_OPMOD_KSWR	0x60
+#define  GSWIP_PCE_TBL_CTRL_ADDR_MASK	GENMASK(4, 0)
+#define GSWIP_PCE_PMAP1			0x453	/* Monitoring port map */
+#define GSWIP_PCE_PMAP2			0x454	/* Default Multicast port map */
+#define GSWIP_PCE_PMAP3			0x455	/* Default Unknown Unicast port map */
+#define GSWIP_PCE_GCTRL_0		0x456
+#define  GSWIP_PCE_GCTRL_0_MC_VALID	BIT(3)
+#define  GSWIP_PCE_GCTRL_0_VLAN		BIT(14) /* VLAN aware Switching */
+#define GSWIP_PCE_GCTRL_1		0x457
+#define  GSWIP_PCE_GCTRL_1_MAC_GLOCK	BIT(2)	/* MAC Address table lock */
+#define  GSWIP_PCE_GCTRL_1_MAC_GLOCK_MOD	BIT(3) /* Mac address table lock forwarding mode */
+#define GSWIP_PCE_PCTRL_0p(p)		(0x480 + ((p) * 0xA))
+#define  GSWIP_PCE_PCTRL_0_INGRESS	BIT(11)
+#define  GSWIP_PCE_PCTRL_0_PSTATE_LISTEN	0x0
+#define  GSWIP_PCE_PCTRL_0_PSTATE_RX		0x1
+#define  GSWIP_PCE_PCTRL_0_PSTATE_TX		0x2
+#define  GSWIP_PCE_PCTRL_0_PSTATE_LEARNING	0x3
+#define  GSWIP_PCE_PCTRL_0_PSTATE_FORWARDING	0x7
+#define  GSWIP_PCE_PCTRL_0_PSTATE_MASK	GENMASK(2, 0)
+
+#define GSWIP_MAC_FLEN			0x8C5
+#define GSWIP_MAC_CTRL_2p(p)		(0x905 + ((p) * 0xC))
+#define GSWIP_MAC_CTRL_2_MLEN		BIT(3) /* Maximum Untagged Frame Lnegth */
+
+/* Ethernet Switch Fetch DMA Port Control Register */
+#define GSWIP_FDMA_PCTRLp(p)		(0xA80 + ((p) * 0x6))
+#define  GSWIP_FDMA_PCTRL_EN		BIT(0)	/* FDMA Port Enable */
+#define  GSWIP_FDMA_PCTRL_STEN		BIT(1)	/* Special Tag Insertion Enable */
+#define  GSWIP_FDMA_PCTRL_VLANMOD_MASK	GENMASK(4, 3)	/* VLAN Modification Control */
+#define  GSWIP_FDMA_PCTRL_VLANMOD_SHIFT	3	/* VLAN Modification Control */
+#define  GSWIP_FDMA_PCTRL_VLANMOD_DIS	(0x0 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
+#define  GSWIP_FDMA_PCTRL_VLANMOD_PRIO	(0x1 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
+#define  GSWIP_FDMA_PCTRL_VLANMOD_ID	(0x2 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
+#define  GSWIP_FDMA_PCTRL_VLANMOD_BOTH	(0x3 << GSWIP_FDMA_PCTRL_VLANMOD_SHIFT)
+
+/* Ethernet Switch Store DMA Port Control Register */
+#define GSWIP_SDMA_PCTRLp(p)		(0xBC0 + ((p) * 0x6))
+#define  GSWIP_SDMA_PCTRL_EN		BIT(0)	/* SDMA Port Enable */
+#define  GSWIP_SDMA_PCTRL_FCEN		BIT(1)	/* Flow Control Enable */
+#define  GSWIP_SDMA_PCTRL_PAUFWD	BIT(1)	/* Pause Frame Forwarding */
+
+#define XRX200_GPHY_FW_ALIGN	(16 * 1024)
+
+struct gswip_hw_info {
+	int max_ports;
+	int cpu_port;
+};
+
+struct xway_gphy_match_data {
+	char *fe_firmware_name;
+	char *ge_firmware_name;
+};
+
+struct gswip_gphy_fw {
+	struct clk *clk_gate;
+	struct reset_control *reset;
+	u32 fw_addr_offset;
+	char *fw_name;
+};
+
+struct gswip_priv {
+	__iomem void *gswip;
+	__iomem void *mdio;
+	__iomem void *mii;
+	const struct gswip_hw_info *hw_info;
+	const struct xway_gphy_match_data *gphy_fw_name_cfg;
+	struct dsa_switch *ds;
+	struct device *dev;
+	struct regmap *rcu_regmap;
+	int num_gphy_fw;
+	struct gswip_gphy_fw *gphy_fw;
+};
+
+struct gswip_rmon_cnt_desc {
+	unsigned int size;
+	unsigned int offset;
+	const char *name;
+};
+
+#define MIB_DESC(_size, _offset, _name) {.size = _size, .offset = _offset, .name = _name}
+
+static const struct gswip_rmon_cnt_desc gswip_rmon_cnt[] = {
+	/** Receive Packet Count (only packets that are accepted and not discarded). */
+	MIB_DESC(1, 0x1F, "RxGoodPkts"),
+	MIB_DESC(1, 0x23, "RxUnicastPkts"),
+	MIB_DESC(1, 0x22, "RxMulticastPkts"),
+	MIB_DESC(1, 0x21, "RxFCSErrorPkts"),
+	MIB_DESC(1, 0x1D, "RxUnderSizeGoodPkts"),
+	MIB_DESC(1, 0x1E, "RxUnderSizeErrorPkts"),
+	MIB_DESC(1, 0x1B, "RxOversizeGoodPkts"),
+	MIB_DESC(1, 0x1C, "RxOversizeErrorPkts"),
+	MIB_DESC(1, 0x20, "RxGoodPausePkts"),
+	MIB_DESC(1, 0x1A, "RxAlignErrorPkts"),
+	MIB_DESC(1, 0x12, "Rx64BytePkts"),
+	MIB_DESC(1, 0x13, "Rx127BytePkts"),
+	MIB_DESC(1, 0x14, "Rx255BytePkts"),
+	MIB_DESC(1, 0x15, "Rx511BytePkts"),
+	MIB_DESC(1, 0x16, "Rx1023BytePkts"),
+	/** Receive Size 1024-1522 (or more, if configured) Packet Count. */
+	MIB_DESC(1, 0x17, "RxMaxBytePkts"),
+	MIB_DESC(1, 0x18, "RxDroppedPkts"),
+	MIB_DESC(1, 0x19, "RxFilteredPkts"),
+	MIB_DESC(2, 0x24, "RxGoodBytes"),
+	MIB_DESC(2, 0x26, "RxBadBytes"),
+	MIB_DESC(1, 0x11, "TxAcmDroppedPkts"),
+	MIB_DESC(1, 0x0C, "TxGoodPkts"),
+	MIB_DESC(1, 0x06, "TxUnicastPkts"),
+	MIB_DESC(1, 0x07, "TxMulticastPkts"),
+	MIB_DESC(1, 0x00, "Tx64BytePkts"),
+	MIB_DESC(1, 0x01, "Tx127BytePkts"),
+	MIB_DESC(1, 0x02, "Tx255BytePkts"),
+	MIB_DESC(1, 0x03, "Tx511BytePkts"),
+	MIB_DESC(1, 0x04, "Tx1023BytePkts"),
+	/** Transmit Size 1024-1522 (or more, if configured) Packet Count. */
+	MIB_DESC(1, 0x05, "TxMaxBytePkts"),
+	MIB_DESC(1, 0x08, "TxSingleCollCount"),
+	MIB_DESC(1, 0x09, "TxMultCollCount"),
+	MIB_DESC(1, 0x0A, "TxLateCollCount"),
+	MIB_DESC(1, 0x0B, "TxExcessCollCount"),
+	MIB_DESC(1, 0x0D, "TxPauseCount"),
+	MIB_DESC(1, 0x10, "TxDroppedPkts"),
+	MIB_DESC(2, 0x0E, "TxGoodBytes"),
+};
+
+static u32 gswip_switch_r(struct gswip_priv *priv, u32 offset)
+{
+	return __raw_readl(priv->gswip + (offset * 4));
+}
+
+static void gswip_switch_w(struct gswip_priv *priv, u32 val, u32 offset)
+{
+	__raw_writel(val, priv->gswip + (offset * 4));
+}
+
+static void gswip_switch_mask(struct gswip_priv *priv, u32 clear, u32 set,
+			      u32 offset)
+{
+	u32 val = gswip_switch_r(priv, offset);
+
+	val &= ~(clear);
+	val |= set;
+	gswip_switch_w(priv, val, offset);
+}
+
+static u32 gswip_switch_r_timeout(struct gswip_priv *priv, u32 offset,
+				  u32 cleared)
+{
+	u32 val;
+
+	return readx_poll_timeout(__raw_readl, priv->gswip + (offset * 4), val,
+				  (val & cleared) == 0, 20, 50000);
+}
+
+static u32 gswip_mdio_r(struct gswip_priv *priv, u32 offset)
+{
+	return __raw_readl(priv->mdio + (offset * 4));
+}
+
+static void gswip_mdio_w(struct gswip_priv *priv, u32 val, u32 offset)
+{
+	__raw_writel(val, priv->mdio + (offset * 4));
+}
+
+static void gswip_mdio_mask(struct gswip_priv *priv, u32 clear, u32 set,
+			    u32 offset)
+{
+	u32 val = gswip_mdio_r(priv, offset);
+
+	val &= ~(clear);
+	val |= set;
+	gswip_mdio_w(priv, val, offset);
+}
+
+static u32 gswip_mii_r(struct gswip_priv *priv, u32 offset)
+{
+	return __raw_readl(priv->mii + (offset * 4));
+}
+
+static void gswip_mii_w(struct gswip_priv *priv, u32 val, u32 offset)
+{
+	__raw_writel(val, priv->mii + (offset * 4));
+}
+
+static void gswip_mii_mask(struct gswip_priv *priv, u32 clear, u32 set,
+			   u32 offset)
+{
+	u32 val = gswip_mii_r(priv, offset);
+
+	val &= ~(clear);
+	val |= set;
+	gswip_mii_w(priv, val, offset);
+}
+
+static void gswip_mii_mask_cfg(struct gswip_priv *priv, u32 clear, u32 set,
+			       int port)
+{
+	switch (port) {
+	case 0:
+		gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG0);
+		break;
+	case 1:
+		gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG1);
+		break;
+	case 5:
+		gswip_mii_mask(priv, clear, set, GSWIP_MII_CFG5);
+		break;
+	}
+}
+
+static void gswip_mii_mask_pcdu(struct gswip_priv *priv, u32 clear, u32 set,
+				int port)
+{
+	switch (port) {
+	case 0:
+		gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU0);
+		break;
+	case 1:
+		gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU1);
+		break;
+	case 5:
+		gswip_mii_mask(priv, clear, set, GSWIP_MII_PCDU5);
+		break;
+	}
+}
+
+static int gswip_mdio_poll(struct gswip_priv *priv)
+{
+	int cnt = 100;
+
+	while (likely(cnt--)) {
+		u32 ctrl = gswip_mdio_r(priv, GSWIP_MDIO_CTRL);
+
+		if ((ctrl & GSWIP_MDIO_CTRL_BUSY) == 0)
+			return 0;
+		usleep_range(20, 40);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int gswip_mdio_wr(struct mii_bus *bus, int addr, int reg, u16 val)
+{
+	struct gswip_priv *priv = bus->priv;
+	int err;
+
+	err = gswip_mdio_poll(priv);
+	if (err) {
+		dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
+		return err;
+	}
+
+	gswip_mdio_w(priv, val, GSWIP_MDIO_WRITE);
+	gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_WR |
+		((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) |
+		(reg & GSWIP_MDIO_CTRL_REGAD_MASK),
+		GSWIP_MDIO_CTRL);
+
+	return 0;
+}
+
+static int gswip_mdio_rd(struct mii_bus *bus, int addr, int reg)
+{
+	struct gswip_priv *priv = bus->priv;
+	int err;
+
+	err = gswip_mdio_poll(priv);
+	if (err) {
+		dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
+		return err;
+	}
+
+	gswip_mdio_w(priv, GSWIP_MDIO_CTRL_BUSY | GSWIP_MDIO_CTRL_RD |
+		((addr & GSWIP_MDIO_CTRL_PHYAD_MASK) << GSWIP_MDIO_CTRL_PHYAD_SHIFT) |
+		(reg & GSWIP_MDIO_CTRL_REGAD_MASK),
+		GSWIP_MDIO_CTRL);
+
+	err = gswip_mdio_poll(priv);
+	if (err) {
+		dev_err(&bus->dev, "waiting for MDIO bus busy timed out\n");
+		return err;
+	}
+
+	return gswip_mdio_r(priv, GSWIP_MDIO_READ);
+}
+
+static int gswip_mdio(struct gswip_priv *priv, struct device_node *mdio_np)
+{
+	struct dsa_switch *ds = priv->ds;
+
+	ds->slave_mii_bus = devm_mdiobus_alloc(priv->dev);
+	if (!ds->slave_mii_bus)
+		return -ENOMEM;
+
+	ds->slave_mii_bus->priv = priv;
+	ds->slave_mii_bus->read = gswip_mdio_rd;
+	ds->slave_mii_bus->write = gswip_mdio_wr;
+	ds->slave_mii_bus->name = "lantiq,xrx200-mdio";
+	snprintf(ds->slave_mii_bus->id, MII_BUS_ID_SIZE, "%s-mii",
+		 dev_name(priv->dev));
+	ds->slave_mii_bus->parent = priv->dev;
+	ds->slave_mii_bus->phy_mask = ~ds->phys_mii_mask;
+
+	return of_mdiobus_register(ds->slave_mii_bus, mdio_np);
+}
+
+static int gswip_port_enable(struct dsa_switch *ds, int port,
+			     struct phy_device *phydev)
+{
+	struct gswip_priv *priv = ds->priv;
+
+	/* RMON Counter Enable for port */
+	gswip_switch_w(priv, GSWIP_BM_PCFG_CNTEN, GSWIP_BM_PCFGp(port));
+
+	/* enable port fetch/store dma & VLAN Modification */
+	gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_EN |
+				   GSWIP_FDMA_PCTRL_VLANMOD_BOTH,
+			 GSWIP_FDMA_PCTRLp(port));
+	gswip_switch_mask(priv, 0, GSWIP_SDMA_PCTRL_EN,
+			  GSWIP_SDMA_PCTRLp(port));
+	gswip_switch_mask(priv, 0, GSWIP_PCE_PCTRL_0_INGRESS,
+			  GSWIP_PCE_PCTRL_0p(port));
+
+	if (!dsa_is_cpu_port(ds, port)) {
+		u32 macconf = GSWIP_MDIO_PHY_LINK_AUTO |
+			      GSWIP_MDIO_PHY_SPEED_AUTO |
+			      GSWIP_MDIO_PHY_FDUP_AUTO |
+			      GSWIP_MDIO_PHY_FCONTX_AUTO |
+			      GSWIP_MDIO_PHY_FCONRX_AUTO |
+			      (phydev->mdio.addr & GSWIP_MDIO_PHY_ADDR_MASK);
+
+		gswip_mdio_w(priv, macconf, GSWIP_MDIO_PHYp(port));
+		/* Activate MDIO auto polling */
+		gswip_mdio_mask(priv, 0, BIT(port), GSWIP_MDIO_MDC_CFG0);
+	}
+
+	return 0;
+}
+
+static void gswip_port_disable(struct dsa_switch *ds, int port,
+			       struct phy_device *phy)
+{
+	struct gswip_priv *priv = ds->priv;
+
+	if (!dsa_is_cpu_port(ds, port)) {
+		gswip_mdio_mask(priv, GSWIP_MDIO_PHY_LINK_DOWN,
+				GSWIP_MDIO_PHY_LINK_MASK,
+				GSWIP_MDIO_PHYp(port));
+		/* Deactivate MDIO auto polling */
+		gswip_mdio_mask(priv, BIT(port), 0, GSWIP_MDIO_MDC_CFG0);
+	}
+
+	gswip_switch_mask(priv, GSWIP_FDMA_PCTRL_EN, 0,
+			  GSWIP_FDMA_PCTRLp(port));
+	gswip_switch_mask(priv, GSWIP_SDMA_PCTRL_EN, 0,
+			  GSWIP_SDMA_PCTRLp(port));
+}
+
+static int gswip_pce_load_microcode(struct gswip_priv *priv)
+{
+	int i;
+	int err;
+
+	gswip_switch_mask(priv, GSWIP_PCE_TBL_CTRL_ADDR_MASK |
+				GSWIP_PCE_TBL_CTRL_OPMOD_MASK,
+			  GSWIP_PCE_TBL_CTRL_OPMOD_ADWR, GSWIP_PCE_TBL_CTRL);
+	gswip_switch_w(priv, 0, GSWIP_PCE_TBL_MASK);
+
+	for (i = 0; i < ARRAY_SIZE(gswip_pce_microcode); i++) {
+		gswip_switch_w(priv, i, GSWIP_PCE_TBL_ADDR);
+		gswip_switch_w(priv, gswip_pce_microcode[i].val_0,
+			       GSWIP_PCE_TBL_VAL(0));
+		gswip_switch_w(priv, gswip_pce_microcode[i].val_1,
+			       GSWIP_PCE_TBL_VAL(1));
+		gswip_switch_w(priv, gswip_pce_microcode[i].val_2,
+			       GSWIP_PCE_TBL_VAL(2));
+		gswip_switch_w(priv, gswip_pce_microcode[i].val_3,
+			       GSWIP_PCE_TBL_VAL(3));
+
+		/* start the table access: */
+		gswip_switch_mask(priv, 0, GSWIP_PCE_TBL_CTRL_BAS,
+				  GSWIP_PCE_TBL_CTRL);
+		err = gswip_switch_r_timeout(priv, GSWIP_PCE_TBL_CTRL,
+					     GSWIP_PCE_TBL_CTRL_BAS);
+		if (err)
+			return err;
+	}
+
+	/* tell the switch that the microcode is loaded */
+	gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_MC_VALID,
+			  GSWIP_PCE_GCTRL_0);
+
+	return 0;
+}
+
+static int gswip_setup(struct dsa_switch *ds)
+{
+	struct gswip_priv *priv = ds->priv;
+	unsigned int cpu_port = priv->hw_info->cpu_port;
+	int i;
+	int err;
+
+	gswip_switch_w(priv, GSWIP_SWRES_R0, GSWIP_SWRES);
+	usleep_range(5000, 10000);
+	gswip_switch_w(priv, 0, GSWIP_SWRES);
+
+	/* disable port fetch/store dma on all ports */
+	for (i = 0; i < priv->hw_info->max_ports; i++)
+		gswip_port_disable(ds, i, NULL);
+
+	/* enable Switch */
+	gswip_mdio_mask(priv, 0, GSWIP_MDIO_GLOB_ENABLE, GSWIP_MDIO_GLOB);
+
+	err = gswip_pce_load_microcode(priv);
+	if (err) {
+		dev_err(priv->dev, "writing PCE microcode failed, %i", err);
+		return err;
+	}
+
+	/* Default unknown Broadcast/Multicast/Unicast port maps */
+	gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP1);
+	gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP2);
+	gswip_switch_w(priv, BIT(cpu_port), GSWIP_PCE_PMAP3);
+
+	/* disable PHY auto polling */
+	gswip_mdio_w(priv, 0x0, GSWIP_MDIO_MDC_CFG0);
+	/* Configure the MDIO Clock 2.5 MHz */
+	gswip_mdio_mask(priv, 0xff, 0x09, GSWIP_MDIO_MDC_CFG1);
+
+	/* Disable the xMII link */
+	gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 0);
+	gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 1);
+	gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, 5);
+
+	/* enable special tag insertion on cpu port */
+	gswip_switch_mask(priv, 0, GSWIP_FDMA_PCTRL_STEN,
+			  GSWIP_FDMA_PCTRLp(cpu_port));
+
+	gswip_switch_mask(priv, 0, GSWIP_MAC_CTRL_2_MLEN,
+			  GSWIP_MAC_CTRL_2p(cpu_port));
+	gswip_switch_w(priv, VLAN_ETH_FRAME_LEN + 8, GSWIP_MAC_FLEN);
+	gswip_switch_mask(priv, 0, GSWIP_BM_QUEUE_GCTRL_GL_MOD,
+			  GSWIP_BM_QUEUE_GCTRL);
+
+	/* VLAN aware Switching */
+	gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_0_VLAN, GSWIP_PCE_GCTRL_0);
+
+	/* Mac Address Table Lock */
+	gswip_switch_mask(priv, 0, GSWIP_PCE_GCTRL_1_MAC_GLOCK |
+				   GSWIP_PCE_GCTRL_1_MAC_GLOCK_MOD,
+			  GSWIP_PCE_GCTRL_1);
+
+	gswip_port_enable(ds, cpu_port, NULL);
+	return 0;
+}
+
+static enum dsa_tag_protocol gswip_get_tag_protocol(struct dsa_switch *ds,
+						    int port)
+{
+	return DSA_TAG_PROTO_GSWIP;
+}
+
+static void gswip_phylink_validate(struct dsa_switch *ds, int port,
+				   unsigned long *supported,
+				   struct phylink_link_state *state)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+	switch (port) {
+	case 0:
+	case 1:
+		if (!phy_interface_mode_is_rgmii(state->interface) &&
+		    state->interface != PHY_INTERFACE_MODE_MII &&
+		    state->interface != PHY_INTERFACE_MODE_REVMII &&
+		    state->interface != PHY_INTERFACE_MODE_RMII) {
+			bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+			dev_err(ds->dev,
+			"Unsupported interface: %d\n", state->interface);
+			return;
+		}
+		break;
+	case 2:
+	case 3:
+	case 4:
+		if (state->interface != PHY_INTERFACE_MODE_INTERNAL) {
+			bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+			dev_err(ds->dev,
+			"Unsupported interface: %d\n", state->interface);
+			return;
+		}
+		break;
+	case 5:
+		if (!phy_interface_mode_is_rgmii(state->interface) &&
+		    state->interface != PHY_INTERFACE_MODE_INTERNAL) {
+			bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
+			dev_err(ds->dev,
+			"Unsupported interface: %d\n", state->interface);
+			return;
+		}
+		break;
+	}
+
+	/* Allow all the expected bits */
+	phylink_set(mask, Autoneg);
+	phylink_set_port_modes(mask);
+	phylink_set(mask, Pause);
+	phylink_set(mask, Asym_Pause);
+
+	/* With the exclusion of MII and Reverse MII, we support Gigabit,
+	 * including Half duplex
+	 */
+	if (state->interface != PHY_INTERFACE_MODE_MII &&
+	    state->interface != PHY_INTERFACE_MODE_REVMII) {
+		phylink_set(mask, 1000baseT_Full);
+		phylink_set(mask, 1000baseT_Half);
+	}
+
+	phylink_set(mask, 10baseT_Half);
+	phylink_set(mask, 10baseT_Full);
+	phylink_set(mask, 100baseT_Half);
+	phylink_set(mask, 100baseT_Full);
+
+	bitmap_and(supported, supported, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+	bitmap_and(state->advertising, state->advertising, mask,
+		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+}
+
+static void gswip_phylink_mac_config(struct dsa_switch *ds, int port,
+				     unsigned int mode,
+				     const struct phylink_link_state *state)
+{
+	struct gswip_priv *priv = ds->priv;
+	u32 miicfg = 0;
+
+	miicfg |= GSWIP_MII_CFG_LDCLKDIS;
+
+	switch (state->interface) {
+	case PHY_INTERFACE_MODE_MII:
+	case PHY_INTERFACE_MODE_INTERNAL:
+		miicfg |= GSWIP_MII_CFG_MODE_MIIM;
+		break;
+	case PHY_INTERFACE_MODE_REVMII:
+		miicfg |= GSWIP_MII_CFG_MODE_MIIP;
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		miicfg |= GSWIP_MII_CFG_MODE_RMIIM;
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		miicfg |= GSWIP_MII_CFG_MODE_RGMII;
+		break;
+	default:
+		dev_err(ds->dev,
+			"Unsupported interface: %d\n", state->interface);
+		return;
+	}
+	gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_MODE_MASK, miicfg, port);
+
+	switch (state->interface) {
+	case PHY_INTERFACE_MODE_RGMII_ID:
+		gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK |
+					  GSWIP_MII_PCDU_RXDLY_MASK, 0, port);
+		break;
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_RXDLY_MASK, 0, port);
+		break;
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		gswip_mii_mask_pcdu(priv, GSWIP_MII_PCDU_TXDLY_MASK, 0, port);
+		break;
+	default:
+		break;
+	}
+}
+
+static void gswip_phylink_mac_link_down(struct dsa_switch *ds, int port,
+					unsigned int mode,
+					phy_interface_t interface)
+{
+	struct gswip_priv *priv = ds->priv;
+
+	gswip_mii_mask_cfg(priv, GSWIP_MII_CFG_EN, 0, port);
+}
+
+static void gswip_phylink_mac_link_up(struct dsa_switch *ds, int port,
+				      unsigned int mode,
+				      phy_interface_t interface,
+				      struct phy_device *phydev)
+{
+	struct gswip_priv *priv = ds->priv;
+
+	/* Enable the xMII interface only for the external PHY */
+	if (interface != PHY_INTERFACE_MODE_INTERNAL)
+		gswip_mii_mask_cfg(priv, 0, GSWIP_MII_CFG_EN, port);
+}
+
+static void gswip_get_strings(struct dsa_switch *ds, int port, u32 stringset,
+			      uint8_t *data)
+{
+	int i;
+
+	if (stringset != ETH_SS_STATS)
+		return;
+
+	for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++)
+		strncpy(data + i * ETH_GSTRING_LEN, gswip_rmon_cnt[i].name,
+			ETH_GSTRING_LEN);
+}
+
+static u32 gswip_bcm_ram_entry_read(struct gswip_priv *priv, u32 table,
+				    u32 index)
+{
+	u32 result;
+	int err;
+
+	gswip_switch_w(priv, index, GSWIP_BM_RAM_ADDR);
+	gswip_switch_mask(priv, GSWIP_BM_RAM_CTRL_ADDR_MASK |
+				GSWIP_BM_RAM_CTRL_OPMOD,
+			      table | GSWIP_BM_RAM_CTRL_BAS,
+			      GSWIP_BM_RAM_CTRL);
+
+	err = gswip_switch_r_timeout(priv, GSWIP_BM_RAM_CTRL,
+				     GSWIP_BM_RAM_CTRL_BAS);
+	if (err) {
+		dev_err(priv->dev, "timeout while reading table: %u, index: %u",
+			table, index);
+		return 0;
+	}
+
+	result = gswip_switch_r(priv, GSWIP_BM_RAM_VAL(0));
+	result |= gswip_switch_r(priv, GSWIP_BM_RAM_VAL(1)) << 16;
+
+	return result;
+}
+
+static void gswip_get_ethtool_stats(struct dsa_switch *ds, int port,
+				    uint64_t *data)
+{
+	struct gswip_priv *priv = ds->priv;
+	const struct gswip_rmon_cnt_desc *rmon_cnt;
+	int i;
+	u64 high;
+
+	for (i = 0; i < ARRAY_SIZE(gswip_rmon_cnt); i++) {
+		rmon_cnt = &gswip_rmon_cnt[i];
+
+		data[i] = gswip_bcm_ram_entry_read(priv, port,
+						   rmon_cnt->offset);
+		if (rmon_cnt->size == 2) {
+			high = gswip_bcm_ram_entry_read(priv, port,
+							rmon_cnt->offset + 1);
+			data[i] |= high << 32;
+		}
+	}
+}
+
+static int gswip_get_sset_count(struct dsa_switch *ds, int port, int sset)
+{
+	if (sset != ETH_SS_STATS)
+		return 0;
+
+	return ARRAY_SIZE(gswip_rmon_cnt);
+}
+
+static const struct dsa_switch_ops gswip_switch_ops = {
+	.get_tag_protocol	= gswip_get_tag_protocol,
+	.setup			= gswip_setup,
+	.port_enable		= gswip_port_enable,
+	.port_disable		= gswip_port_disable,
+	.phylink_validate	= gswip_phylink_validate,
+	.phylink_mac_config	= gswip_phylink_mac_config,
+	.phylink_mac_link_down	= gswip_phylink_mac_link_down,
+	.phylink_mac_link_up	= gswip_phylink_mac_link_up,
+	.get_strings		= gswip_get_strings,
+	.get_ethtool_stats	= gswip_get_ethtool_stats,
+	.get_sset_count		= gswip_get_sset_count,
+};
+
+static const struct xway_gphy_match_data xrx200a1x_gphy_data = {
+	.fe_firmware_name = "lantiq/xrx200_phy22f_a14.bin",
+	.ge_firmware_name = "lantiq/xrx200_phy11g_a14.bin",
+};
+
+static const struct xway_gphy_match_data xrx200a2x_gphy_data = {
+	.fe_firmware_name = "lantiq/xrx200_phy22f_a22.bin",
+	.ge_firmware_name = "lantiq/xrx200_phy11g_a22.bin",
+};
+
+static const struct xway_gphy_match_data xrx300_gphy_data = {
+	.fe_firmware_name = "lantiq/xrx300_phy22f_a21.bin",
+	.ge_firmware_name = "lantiq/xrx300_phy11g_a21.bin",
+};
+
+static const struct of_device_id xway_gphy_match[] = {
+	{ .compatible = "lantiq,xrx200-gphy-fw", .data = NULL },
+	{ .compatible = "lantiq,xrx200a1x-gphy-fw", .data = &xrx200a1x_gphy_data },
+	{ .compatible = "lantiq,xrx200a2x-gphy-fw", .data = &xrx200a2x_gphy_data },
+	{ .compatible = "lantiq,xrx300-gphy-fw", .data = &xrx300_gphy_data },
+	{ .compatible = "lantiq,xrx330-gphy-fw", .data = &xrx300_gphy_data },
+	{},
+};
+
+static int gswip_gphy_fw_load(struct gswip_priv *priv, struct gswip_gphy_fw *gphy_fw)
+{
+	struct device *dev = priv->dev;
+	const struct firmware *fw;
+	void *fw_addr;
+	dma_addr_t dma_addr;
+	dma_addr_t dev_addr;
+	size_t size;
+	int ret;
+
+	ret = clk_prepare_enable(gphy_fw->clk_gate);
+	if (ret)
+		return ret;
+
+	reset_control_assert(gphy_fw->reset);
+
+	ret = request_firmware(&fw, gphy_fw->fw_name, dev);
+	if (ret) {
+		dev_err(dev, "failed to load firmware: %s, error: %i\n",
+			gphy_fw->fw_name, ret);
+		return ret;
+	}
+
+	/* GPHY cores need the firmware code in a persistent and contiguous
+	 * memory area with a 16 kB boundary aligned start address.
+	 */
+	size = fw->size + XRX200_GPHY_FW_ALIGN;
+
+	fw_addr = dmam_alloc_coherent(dev, size, &dma_addr, GFP_KERNEL);
+	if (fw_addr) {
+		fw_addr = PTR_ALIGN(fw_addr, XRX200_GPHY_FW_ALIGN);
+		dev_addr = ALIGN(dma_addr, XRX200_GPHY_FW_ALIGN);
+		memcpy(fw_addr, fw->data, fw->size);
+	} else {
+		dev_err(dev, "failed to alloc firmware memory\n");
+		release_firmware(fw);
+		return -ENOMEM;
+	}
+
+	release_firmware(fw);
+
+	ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, dev_addr);
+	if (ret)
+		return ret;
+
+	reset_control_deassert(gphy_fw->reset);
+
+	return ret;
+}
+
+static int gswip_gphy_fw_probe(struct gswip_priv *priv,
+			       struct gswip_gphy_fw *gphy_fw,
+			       struct device_node *gphy_fw_np, int i)
+{
+	struct device *dev = priv->dev;
+	u32 gphy_mode;
+	int ret;
+	char gphyname[10];
+
+	snprintf(gphyname, sizeof(gphyname), "gphy%d", i);
+
+	gphy_fw->clk_gate = devm_clk_get(dev, gphyname);
+	if (IS_ERR(gphy_fw->clk_gate)) {
+		dev_err(dev, "Failed to lookup gate clock\n");
+		return PTR_ERR(gphy_fw->clk_gate);
+	}
+
+	ret = of_property_read_u32(gphy_fw_np, "reg", &gphy_fw->fw_addr_offset);
+	if (ret)
+		return ret;
+
+	ret = of_property_read_u32(gphy_fw_np, "lantiq,gphy-mode", &gphy_mode);
+	/* Default to GE mode */
+	if (ret)
+		gphy_mode = GPHY_MODE_GE;
+
+	switch (gphy_mode) {
+	case GPHY_MODE_FE:
+		gphy_fw->fw_name = priv->gphy_fw_name_cfg->fe_firmware_name;
+		break;
+	case GPHY_MODE_GE:
+		gphy_fw->fw_name = priv->gphy_fw_name_cfg->ge_firmware_name;
+		break;
+	default:
+		dev_err(dev, "Unknown GPHY mode %d\n", gphy_mode);
+		return -EINVAL;
+	}
+
+	gphy_fw->reset = of_reset_control_array_get_exclusive(gphy_fw_np);
+	if (IS_ERR(priv->gphy_fw)) {
+		if (PTR_ERR(priv->gphy_fw) != -EPROBE_DEFER)
+			dev_err(dev, "Failed to lookup gphy reset\n");
+		return PTR_ERR(priv->gphy_fw);
+	}
+
+	return gswip_gphy_fw_load(priv, gphy_fw);
+}
+
+static void gswip_gphy_fw_remove(struct gswip_priv *priv,
+				 struct gswip_gphy_fw *gphy_fw)
+{
+	int ret;
+
+	/* check if the device was fully probed */
+	if (!gphy_fw->fw_name)
+		return;
+
+	ret = regmap_write(priv->rcu_regmap, gphy_fw->fw_addr_offset, 0);
+	if (ret)
+		dev_err(priv->dev, "can not reset GPHY FW pointer");
+
+	clk_disable_unprepare(gphy_fw->clk_gate);
+
+	reset_control_put(gphy_fw->reset);
+}
+
+static int gswip_gphy_fw_list(struct gswip_priv *priv,
+			      struct device_node *gphy_fw_list_np, u32 version)
+{
+	struct device *dev = priv->dev;
+	struct device_node *gphy_fw_np;
+	const struct of_device_id *match;
+	int err;
+	int i = 0;
+
+	/* The The VRX200 rev 1.1 uses the GSWIP 2.0 and needs the older
+	 * GPHY firmware. The VRX200 rev 1.2 uses the GSWIP 2.1 and also
+	 * needs a different GPHY firmware.
+	 */
+	if (of_device_is_compatible(gphy_fw_list_np, "lantiq,xrx200-gphy-fw")) {
+		switch (version) {
+		case GSWIP_VERSION_2_0:
+			priv->gphy_fw_name_cfg = &xrx200a1x_gphy_data;
+			break;
+		case GSWIP_VERSION_2_1:
+			priv->gphy_fw_name_cfg = &xrx200a2x_gphy_data;
+			break;
+		default:
+			dev_err(dev, "unknown GSWIP version: 0x%x", version);
+			return -ENOENT;
+		}
+	}
+
+	match = of_match_node(xway_gphy_match, gphy_fw_list_np);
+	if (match && match->data)
+		priv->gphy_fw_name_cfg = match->data;
+
+	if (!priv->gphy_fw_name_cfg) {
+		dev_err(dev, "GPHY compatible type not supported");
+		return -ENOENT;
+	}
+
+	priv->num_gphy_fw = of_get_available_child_count(gphy_fw_list_np);
+	if (!priv->num_gphy_fw)
+		return -ENOENT;
+
+	priv->rcu_regmap = syscon_regmap_lookup_by_phandle(gphy_fw_list_np,
+							   "lantiq,rcu");
+	if (IS_ERR(priv->rcu_regmap))
+		return PTR_ERR(priv->rcu_regmap);
+
+	priv->gphy_fw = devm_kmalloc_array(dev, priv->num_gphy_fw,
+					   sizeof(*priv->gphy_fw),
+					   GFP_KERNEL | __GFP_ZERO);
+	if (!priv->gphy_fw)
+		return -ENOMEM;
+
+	for_each_available_child_of_node(gphy_fw_list_np, gphy_fw_np) {
+		err = gswip_gphy_fw_probe(priv, &priv->gphy_fw[i],
+					  gphy_fw_np, i);
+		if (err)
+			goto remove_gphy;
+		i++;
+	}
+
+	return 0;
+
+remove_gphy:
+	for (i = 0; i < priv->num_gphy_fw; i++)
+		gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
+	return err;
+}
+
+static int gswip_probe(struct platform_device *pdev)
+{
+	struct gswip_priv *priv;
+	struct resource *gswip_res, *mdio_res, *mii_res;
+	struct device_node *mdio_np, *gphy_fw_np;
+	struct device *dev = &pdev->dev;
+	int err;
+	int i;
+	u32 version;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	gswip_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->gswip = devm_ioremap_resource(dev, gswip_res);
+	if (!priv->gswip)
+		return -ENOMEM;
+
+	mdio_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	priv->mdio = devm_ioremap_resource(dev, mdio_res);
+	if (!priv->mdio)
+		return -ENOMEM;
+
+	mii_res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+	priv->mii = devm_ioremap_resource(dev, mii_res);
+	if (!priv->mii)
+		return -ENOMEM;
+
+	priv->hw_info = of_device_get_match_data(dev);
+	if (!priv->hw_info)
+		return -EINVAL;
+
+	priv->ds = dsa_switch_alloc(dev, priv->hw_info->max_ports);
+	if (!priv->ds)
+		return -ENOMEM;
+
+	priv->ds->priv = priv;
+	priv->ds->ops = &gswip_switch_ops;
+	priv->dev = dev;
+	version = gswip_switch_r(priv, GSWIP_VERSION);
+
+	/* bring up the mdio bus */
+	gphy_fw_np = of_find_compatible_node(pdev->dev.of_node, NULL,
+					     "lantiq,gphy-fw");
+	if (gphy_fw_np) {
+		err = gswip_gphy_fw_list(priv, gphy_fw_np, version);
+		if (err) {
+			dev_err(dev, "gphy fw probe failed\n");
+			return err;
+		}
+	}
+
+	/* bring up the mdio bus */
+	mdio_np = of_find_compatible_node(pdev->dev.of_node, NULL,
+					  "lantiq,xrx200-mdio");
+	if (mdio_np) {
+		err = gswip_mdio(priv, mdio_np);
+		if (err) {
+			dev_err(dev, "mdio probe failed\n");
+			goto gphy_fw;
+		}
+	}
+
+	err = dsa_register_switch(priv->ds);
+	if (err) {
+		dev_err(dev, "dsa switch register failed: %i\n", err);
+		goto mdio_bus;
+	}
+	if (priv->ds->dst->cpu_dp->index != priv->hw_info->cpu_port) {
+		dev_err(dev, "wrong CPU port defined, HW only supports port: %i",
+			priv->hw_info->cpu_port);
+		err = -EINVAL;
+		goto mdio_bus;
+	}
+
+	platform_set_drvdata(pdev, priv);
+
+	dev_info(dev, "probed GSWIP version %lx mod %lx\n",
+		 (version & GSWIP_VERSION_REV_MASK) >> GSWIP_VERSION_REV_SHIFT,
+		 (version & GSWIP_VERSION_MOD_MASK) >> GSWIP_VERSION_MOD_SHIFT);
+	return 0;
+
+mdio_bus:
+	if (mdio_np)
+		mdiobus_unregister(priv->ds->slave_mii_bus);
+gphy_fw:
+	for (i = 0; i < priv->num_gphy_fw; i++)
+		gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
+	return err;
+}
+
+static int gswip_remove(struct platform_device *pdev)
+{
+	struct gswip_priv *priv = platform_get_drvdata(pdev);
+	int i;
+
+	if (!priv)
+		return 0;
+
+	/* disable the switch */
+	gswip_mdio_mask(priv, GSWIP_MDIO_GLOB_ENABLE, 0, GSWIP_MDIO_GLOB);
+
+	dsa_unregister_switch(priv->ds);
+
+	if (priv->ds->slave_mii_bus)
+		mdiobus_unregister(priv->ds->slave_mii_bus);
+
+	for (i = 0; i < priv->num_gphy_fw; i++)
+		gswip_gphy_fw_remove(priv, &priv->gphy_fw[i]);
+
+	return 0;
+}
+
+static const struct gswip_hw_info gswip_xrx200 = {
+	.max_ports = 7,
+	.cpu_port = 6,
+};
+
+static const struct of_device_id gswip_of_match[] = {
+	{ .compatible = "lantiq,xrx200-gswip", .data = &gswip_xrx200 },
+	{},
+};
+MODULE_DEVICE_TABLE(of, gswip_of_match);
+
+static struct platform_driver gswip_driver = {
+	.probe = gswip_probe,
+	.remove = gswip_remove,
+	.driver = {
+		.name = "gswip",
+		.of_match_table = gswip_of_match,
+	},
+};
+
+module_platform_driver(gswip_driver);
+
+MODULE_AUTHOR("Hauke Mehrtens <hauke@hauke-m.de>");
+MODULE_DESCRIPTION("Lantiq / Intel GSWIP driver");
+MODULE_LICENSE("GPL v2");

drivers/net/dsa/lantiq_pce.h

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * PCE microcode extracted from UGW 7.1.1 switch api
+ *
+ * Copyright (c) 2012, 2014, 2015 Lantiq Deutschland GmbH
+ * Copyright (C) 2012 John Crispin <john@phrozen.org>
+ * Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+enum {
+	OUT_MAC0 = 0,
+	OUT_MAC1,
+	OUT_MAC2,
+	OUT_MAC3,
+	OUT_MAC4,
+	OUT_MAC5,
+	OUT_ETHTYP,
+	OUT_VTAG0,
+	OUT_VTAG1,
+	OUT_ITAG0,
+	OUT_ITAG1,	/*10 */
+	OUT_ITAG2,
+	OUT_ITAG3,
+	OUT_IP0,
+	OUT_IP1,
+	OUT_IP2,
+	OUT_IP3,
+	OUT_SIP0,
+	OUT_SIP1,
+	OUT_SIP2,
+	OUT_SIP3,	/*20*/
+	OUT_SIP4,
+	OUT_SIP5,
+	OUT_SIP6,
+	OUT_SIP7,
+	OUT_DIP0,
+	OUT_DIP1,
+	OUT_DIP2,
+	OUT_DIP3,
+	OUT_DIP4,
+	OUT_DIP5,	/*30*/
+	OUT_DIP6,
+	OUT_DIP7,
+	OUT_SESID,
+	OUT_PROT,
+	OUT_APP0,
+	OUT_APP1,
+	OUT_IGMP0,
+	OUT_IGMP1,
+	OUT_IPOFF,	/*39*/
+	OUT_NONE = 63,
+};
+
+/* parser's microcode length type */
+#define INSTR		0
+#define IPV6		1
+#define LENACCU		2
+
+/* parser's microcode flag type */
+enum {
+	FLAG_ITAG = 0,
+	FLAG_VLAN,
+	FLAG_SNAP,
+	FLAG_PPPOE,
+	FLAG_IPV6,
+	FLAG_IPV6FL,
+	FLAG_IPV4,
+	FLAG_IGMP,
+	FLAG_TU,
+	FLAG_HOP,
+	FLAG_NN1,	/*10 */
+	FLAG_NN2,
+	FLAG_END,
+	FLAG_NO,	/*13*/
+};
+
+struct gswip_pce_microcode {
+	u16 val_3;
+	u16 val_2;
+	u16 val_1;
+	u16 val_0;
+};
+
+#define MC_ENTRY(val, msk, ns, out, len, type, flags, ipv4_len) \
+	{ val, msk, ((ns) << 10 | (out) << 4 | (len) >> 1),\
+		((len) & 1) << 15 | (type) << 13 | (flags) << 9 | (ipv4_len) << 8 }
+static const struct gswip_pce_microcode gswip_pce_microcode[] = {
+	/*      value    mask    ns  fields      L  type     flags       ipv4_len */
+	MC_ENTRY(0x88c3, 0xFFFF,  1, OUT_ITAG0,  4, INSTR,   FLAG_ITAG,  0),
+	MC_ENTRY(0x8100, 0xFFFF,  2, OUT_VTAG0,  2, INSTR,   FLAG_VLAN,  0),
+	MC_ENTRY(0x88A8, 0xFFFF,  1, OUT_VTAG0,  2, INSTR,   FLAG_VLAN,  0),
+	MC_ENTRY(0x8100, 0xFFFF,  1, OUT_VTAG0,  2, INSTR,   FLAG_VLAN,  0),
+	MC_ENTRY(0x8864, 0xFFFF, 17, OUT_ETHTYP, 1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0800, 0xFFFF, 21, OUT_ETHTYP, 1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x86DD, 0xFFFF, 22, OUT_ETHTYP, 1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x8863, 0xFFFF, 16, OUT_ETHTYP, 1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0xF800, 10, OUT_NONE,   0, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 40, OUT_ETHTYP, 1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0600, 0x0600, 40, OUT_ETHTYP, 1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 12, OUT_NONE,   1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0xAAAA, 0xFFFF, 14, OUT_NONE,   1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0300, 0xFF00, 41, OUT_NONE,   0, INSTR,   FLAG_SNAP,  0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_DIP7,   3, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 18, OUT_DIP7,   3, INSTR,   FLAG_PPPOE, 0),
+	MC_ENTRY(0x0021, 0xFFFF, 21, OUT_NONE,   1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0057, 0xFFFF, 22, OUT_NONE,   1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 40, OUT_NONE,   0, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x4000, 0xF000, 24, OUT_IP0,    4, INSTR,   FLAG_IPV4,  1),
+	MC_ENTRY(0x6000, 0xF000, 27, OUT_IP0,    3, INSTR,   FLAG_IPV6,  0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 25, OUT_IP3,    2, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 26, OUT_SIP0,   4, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 40, OUT_NONE,   0, LENACCU, FLAG_NO,    0),
+	MC_ENTRY(0x1100, 0xFF00, 39, OUT_PROT,   1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0600, 0xFF00, 39, OUT_PROT,   1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0xFF00, 33, OUT_IP3,   17, INSTR,   FLAG_HOP,   0),
+	MC_ENTRY(0x2B00, 0xFF00, 33, OUT_IP3,   17, INSTR,   FLAG_NN1,   0),
+	MC_ENTRY(0x3C00, 0xFF00, 33, OUT_IP3,   17, INSTR,   FLAG_NN2,   0),
+	MC_ENTRY(0x0000, 0x0000, 39, OUT_PROT,   1, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x00E0, 35, OUT_NONE,   0, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 40, OUT_NONE,   0, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0xFF00, 33, OUT_NONE,   0, IPV6,    FLAG_HOP,   0),
+	MC_ENTRY(0x2B00, 0xFF00, 33, OUT_NONE,   0, IPV6,    FLAG_NN1,   0),
+	MC_ENTRY(0x3C00, 0xFF00, 33, OUT_NONE,   0, IPV6,    FLAG_NN2,   0),
+	MC_ENTRY(0x0000, 0x0000, 40, OUT_PROT,   1, IPV6,    FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 40, OUT_SIP0,  16, INSTR,   FLAG_NO,    0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_APP0,   4, INSTR,   FLAG_IGMP,  0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+	MC_ENTRY(0x0000, 0x0000, 41, OUT_NONE,   0, INSTR,   FLAG_END,   0),
+};

drivers/net/ethernet/Kconfig

@@ -108,6 +108,13 @@ config LANTIQ_ETOP
 	---help---
 	  Support for the MII0 inside the Lantiq SoC
 
+config LANTIQ_XRX200
+	tristate "Lantiq / Intel xRX200 PMAC network driver"
+	depends on SOC_TYPE_XWAY
+	---help---
+	  Support for the PMAC of the Gigabit switch (GSWIP) inside the
+	  Lantiq / Intel VRX200 VDSL SoC
+
 source "drivers/net/ethernet/marvell/Kconfig"
 source "drivers/net/ethernet/mediatek/Kconfig"
 source "drivers/net/ethernet/mellanox/Kconfig"

drivers/net/ethernet/Makefile

@@ -49,6 +49,7 @@ obj-$(CONFIG_NET_VENDOR_XSCALE) += xscale/
 obj-$(CONFIG_JME) += jme.o
 obj-$(CONFIG_KORINA) += korina.o
 obj-$(CONFIG_LANTIQ_ETOP) += lantiq_etop.o
+obj-$(CONFIG_LANTIQ_XRX200) += lantiq_xrx200.o
 obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
 obj-$(CONFIG_NET_VENDOR_MEDIATEK) += mediatek/
 obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/

drivers/net/ethernet/lantiq_etop.c

@@ -432,6 +432,7 @@ ltq_etop_open(struct net_device *dev)
 		if (!IS_TX(i) && (!IS_RX(i)))
 			continue;
 		ltq_dma_open(&ch->dma);
+		ltq_dma_enable_irq(&ch->dma);
 		napi_enable(&ch->napi);
 	}
 	phy_start(dev->phydev);

drivers/net/ethernet/lantiq_xrx200.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Lantiq / Intel PMAC driver for XRX200 SoCs
+ *
+ * Copyright (C) 2010 Lantiq Deutschland
+ * Copyright (C) 2012 John Crispin <john@phrozen.org>
+ * Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+
+#include <xway_dma.h>
+
+/* DMA */
+#define XRX200_DMA_DATA_LEN	0x600
+#define XRX200_DMA_RX		0
+#define XRX200_DMA_TX		1
+
+/* cpu port mac */
+#define PMAC_RX_IPG		0x0024
+#define PMAC_RX_IPG_MASK	0xf
+
+#define PMAC_HD_CTL		0x0000
+/* Add Ethernet header to packets from DMA to PMAC */
+#define PMAC_HD_CTL_ADD		BIT(0)
+/* Add VLAN tag to Packets from DMA to PMAC */
+#define PMAC_HD_CTL_TAG		BIT(1)
+/* Add CRC to packets from DMA to PMAC */
+#define PMAC_HD_CTL_AC		BIT(2)
+/* Add status header to packets from PMAC to DMA */
+#define PMAC_HD_CTL_AS		BIT(3)
+/* Remove CRC from packets from PMAC to DMA */
+#define PMAC_HD_CTL_RC		BIT(4)
+/* Remove Layer-2 header from packets from PMAC to DMA */
+#define PMAC_HD_CTL_RL2		BIT(5)
+/* Status header is present from DMA to PMAC */
+#define PMAC_HD_CTL_RXSH	BIT(6)
+/* Add special tag from PMAC to switch */
+#define PMAC_HD_CTL_AST		BIT(7)
+/* Remove specail Tag from PMAC to DMA */
+#define PMAC_HD_CTL_RST		BIT(8)
+/* Check CRC from DMA to PMAC */
+#define PMAC_HD_CTL_CCRC	BIT(9)
+/* Enable reaction to Pause frames in the PMAC */
+#define PMAC_HD_CTL_FC		BIT(10)
+
+struct xrx200_chan {
+	int tx_free;
+
+	struct napi_struct napi;
+	struct ltq_dma_channel dma;
+	struct sk_buff *skb[LTQ_DESC_NUM];
+
+	struct xrx200_priv *priv;
+};
+
+struct xrx200_priv {
+	struct clk *clk;
+
+	struct xrx200_chan chan_tx;
+	struct xrx200_chan chan_rx;
+
+	struct net_device *net_dev;
+	struct device *dev;
+
+	__iomem void *pmac_reg;
+};
+
+static u32 xrx200_pmac_r32(struct xrx200_priv *priv, u32 offset)
+{
+	return __raw_readl(priv->pmac_reg + offset);
+}
+
+static void xrx200_pmac_w32(struct xrx200_priv *priv, u32 val, u32 offset)
+{
+	__raw_writel(val, priv->pmac_reg + offset);
+}
+
+static void xrx200_pmac_mask(struct xrx200_priv *priv, u32 clear, u32 set,
+			     u32 offset)
+{
+	u32 val = xrx200_pmac_r32(priv, offset);
+
+	val &= ~(clear);
+	val |= set;
+	xrx200_pmac_w32(priv, val, offset);
+}
+
+/* drop all the packets from the DMA ring */
+static void xrx200_flush_dma(struct xrx200_chan *ch)
+{
+	int i;
+
+	for (i = 0; i < LTQ_DESC_NUM; i++) {
+		struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
+
+		if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) != LTQ_DMA_C)
+			break;
+
+		desc->ctl = LTQ_DMA_OWN | LTQ_DMA_RX_OFFSET(NET_IP_ALIGN) |
+			    XRX200_DMA_DATA_LEN;
+		ch->dma.desc++;
+		ch->dma.desc %= LTQ_DESC_NUM;
+	}
+}
+
+static int xrx200_open(struct net_device *net_dev)
+{
+	struct xrx200_priv *priv = netdev_priv(net_dev);
+	int err;
+
+	/* enable clock gate */
+	err = clk_prepare_enable(priv->clk);
+	if (err)
+		return err;
+
+	napi_enable(&priv->chan_tx.napi);
+	ltq_dma_open(&priv->chan_tx.dma);
+	ltq_dma_enable_irq(&priv->chan_tx.dma);
+
+	napi_enable(&priv->chan_rx.napi);
+	ltq_dma_open(&priv->chan_rx.dma);
+	/* The boot loader does not always deactivate the receiving of frames
+	 * on the ports and then some packets queue up in the PPE buffers.
+	 * They already passed the PMAC so they do not have the tags
+	 * configured here. Read the these packets here and drop them.
+	 * The HW should have written them into memory after 10us
+	 */
+	usleep_range(20, 40);
+	xrx200_flush_dma(&priv->chan_rx);
+	ltq_dma_enable_irq(&priv->chan_rx.dma);
+
+	netif_wake_queue(net_dev);
+
+	return 0;
+}
+
+static int xrx200_close(struct net_device *net_dev)
+{
+	struct xrx200_priv *priv = netdev_priv(net_dev);
+
+	netif_stop_queue(net_dev);
+
+	napi_disable(&priv->chan_rx.napi);
+	ltq_dma_close(&priv->chan_rx.dma);
+
+	napi_disable(&priv->chan_tx.napi);
+	ltq_dma_close(&priv->chan_tx.dma);
+
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static int xrx200_alloc_skb(struct xrx200_chan *ch)
+{
+	int ret = 0;
+
+	ch->skb[ch->dma.desc] = netdev_alloc_skb_ip_align(ch->priv->net_dev,
+							  XRX200_DMA_DATA_LEN);
+	if (!ch->skb[ch->dma.desc]) {
+		ret = -ENOMEM;
+		goto skip;
+	}
+
+	ch->dma.desc_base[ch->dma.desc].addr = dma_map_single(ch->priv->dev,
+			ch->skb[ch->dma.desc]->data, XRX200_DMA_DATA_LEN,
+			DMA_FROM_DEVICE);
+	if (unlikely(dma_mapping_error(ch->priv->dev,
+				       ch->dma.desc_base[ch->dma.desc].addr))) {
+		dev_kfree_skb_any(ch->skb[ch->dma.desc]);
+		ret = -ENOMEM;
+		goto skip;
+	}
+
+skip:
+	ch->dma.desc_base[ch->dma.desc].ctl =
+		LTQ_DMA_OWN | LTQ_DMA_RX_OFFSET(NET_IP_ALIGN) |
+		XRX200_DMA_DATA_LEN;
+
+	return ret;
+}
+
+static int xrx200_hw_receive(struct xrx200_chan *ch)
+{
+	struct xrx200_priv *priv = ch->priv;
+	struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
+	struct sk_buff *skb = ch->skb[ch->dma.desc];
+	int len = (desc->ctl & LTQ_DMA_SIZE_MASK);
+	struct net_device *net_dev = priv->net_dev;
+	int ret;
+
+	ret = xrx200_alloc_skb(ch);
+
+	ch->dma.desc++;
+	ch->dma.desc %= LTQ_DESC_NUM;
+
+	if (ret) {
+		netdev_err(net_dev, "failed to allocate new rx buffer\n");
+		return ret;
+	}
+
+	skb_put(skb, len);
+	skb->protocol = eth_type_trans(skb, net_dev);
+	netif_receive_skb(skb);
+	net_dev->stats.rx_packets++;
+	net_dev->stats.rx_bytes += len - ETH_FCS_LEN;
+
+	return 0;
+}
+
+static int xrx200_poll_rx(struct napi_struct *napi, int budget)
+{
+	struct xrx200_chan *ch = container_of(napi,
+				struct xrx200_chan, napi);
+	int rx = 0;
+	int ret;
+
+	while (rx < budget) {
+		struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
+
+		if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) {
+			ret = xrx200_hw_receive(ch);
+			if (ret)
+				return ret;
+			rx++;
+		} else {
+			break;
+		}
+	}
+
+	if (rx < budget) {
+		napi_complete(&ch->napi);
+		ltq_dma_enable_irq(&ch->dma);
+	}
+
+	return rx;
+}
+
+static int xrx200_tx_housekeeping(struct napi_struct *napi, int budget)
+{
+	struct xrx200_chan *ch = container_of(napi,
+				struct xrx200_chan, napi);
+	struct net_device *net_dev = ch->priv->net_dev;
+	int pkts = 0;
+	int bytes = 0;
+
+	while (pkts < budget) {
+		struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->tx_free];
+
+		if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) {
+			struct sk_buff *skb = ch->skb[ch->tx_free];
+
+			pkts++;
+			bytes += skb->len;
+			ch->skb[ch->tx_free] = NULL;
+			consume_skb(skb);
+			memset(&ch->dma.desc_base[ch->tx_free], 0,
+			       sizeof(struct ltq_dma_desc));
+			ch->tx_free++;
+			ch->tx_free %= LTQ_DESC_NUM;
+		} else {
+			break;
+		}
+	}
+
+	net_dev->stats.tx_packets += pkts;
+	net_dev->stats.tx_bytes += bytes;
+	netdev_completed_queue(ch->priv->net_dev, pkts, bytes);
+
+	if (pkts < budget) {
+		napi_complete(&ch->napi);
+		ltq_dma_enable_irq(&ch->dma);
+	}
+
+	return pkts;
+}
+
+static int xrx200_start_xmit(struct sk_buff *skb, struct net_device *net_dev)
+{
+	struct xrx200_priv *priv = netdev_priv(net_dev);
+	struct xrx200_chan *ch = &priv->chan_tx;
+	struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc];
+	u32 byte_offset;
+	dma_addr_t mapping;
+	int len;
+
+	skb->dev = net_dev;
+	if (skb_put_padto(skb, ETH_ZLEN)) {
+		net_dev->stats.tx_dropped++;
+		return NETDEV_TX_OK;
+	}
+
+	len = skb->len;
+
+	if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) || ch->skb[ch->dma.desc]) {
+		netdev_err(net_dev, "tx ring full\n");
+		netif_stop_queue(net_dev);
+		return NETDEV_TX_BUSY;
+	}
+
+	ch->skb[ch->dma.desc] = skb;
+
+	mapping = dma_map_single(priv->dev, skb->data, len, DMA_TO_DEVICE);
+	if (unlikely(dma_mapping_error(priv->dev, mapping)))
+		goto err_drop;
+
+	/* dma needs to start on a 16 byte aligned address */
+	byte_offset = mapping % 16;
+
+	desc->addr = mapping - byte_offset;
+	/* Make sure the address is written before we give it to HW */
+	wmb();
+	desc->ctl = LTQ_DMA_OWN | LTQ_DMA_SOP | LTQ_DMA_EOP |
+		LTQ_DMA_TX_OFFSET(byte_offset) | (len & LTQ_DMA_SIZE_MASK);
+	ch->dma.desc++;
+	ch->dma.desc %= LTQ_DESC_NUM;
+	if (ch->dma.desc == ch->tx_free)
+		netif_stop_queue(net_dev);
+
+	netdev_sent_queue(net_dev, len);
+
+	return NETDEV_TX_OK;
+
+err_drop:
+	dev_kfree_skb(skb);
+	net_dev->stats.tx_dropped++;
+	net_dev->stats.tx_errors++;
+	return NETDEV_TX_OK;
+}
+
+static const struct net_device_ops xrx200_netdev_ops = {
+	.ndo_open		= xrx200_open,
+	.ndo_stop		= xrx200_close,
+	.ndo_start_xmit		= xrx200_start_xmit,
+	.ndo_set_mac_address	= eth_mac_addr,
+	.ndo_validate_addr	= eth_validate_addr,
+	.ndo_change_mtu		= eth_change_mtu,
+};
+
+static irqreturn_t xrx200_dma_irq(int irq, void *ptr)
+{
+	struct xrx200_chan *ch = ptr;
+
+	ltq_dma_disable_irq(&ch->dma);
+	ltq_dma_ack_irq(&ch->dma);
+
+	napi_schedule(&ch->napi);
+
+	return IRQ_HANDLED;
+}
+
+static int xrx200_dma_init(struct xrx200_priv *priv)
+{
+	struct xrx200_chan *ch_rx = &priv->chan_rx;
+	struct xrx200_chan *ch_tx = &priv->chan_tx;
+	int ret = 0;
+	int i;
+
+	ltq_dma_init_port(DMA_PORT_ETOP);
+
+	ch_rx->dma.nr = XRX200_DMA_RX;
+	ch_rx->dma.dev = priv->dev;
+	ch_rx->priv = priv;
+
+	ltq_dma_alloc_rx(&ch_rx->dma);
+	for (ch_rx->dma.desc = 0; ch_rx->dma.desc < LTQ_DESC_NUM;
+	     ch_rx->dma.desc++) {
+		ret = xrx200_alloc_skb(ch_rx);
+		if (ret)
+			goto rx_free;
+	}
+	ch_rx->dma.desc = 0;
+	ret = devm_request_irq(priv->dev, ch_rx->dma.irq, xrx200_dma_irq, 0,
+			       "xrx200_net_rx", &priv->chan_rx);
+	if (ret) {
+		dev_err(priv->dev, "failed to request RX irq %d\n",
+			ch_rx->dma.irq);
+		goto rx_ring_free;
+	}
+
+	ch_tx->dma.nr = XRX200_DMA_TX;
+	ch_tx->dma.dev = priv->dev;
+	ch_tx->priv = priv;
+
+	ltq_dma_alloc_tx(&ch_tx->dma);
+	ret = devm_request_irq(priv->dev, ch_tx->dma.irq, xrx200_dma_irq, 0,
+			       "xrx200_net_tx", &priv->chan_tx);
+	if (ret) {
+		dev_err(priv->dev, "failed to request TX irq %d\n",
+			ch_tx->dma.irq);
+		goto tx_free;
+	}
+
+	return ret;
+
+tx_free:
+	ltq_dma_free(&ch_tx->dma);
+
+rx_ring_free:
+	/* free the allocated RX ring */
+	for (i = 0; i < LTQ_DESC_NUM; i++) {
+		if (priv->chan_rx.skb[i])
+			dev_kfree_skb_any(priv->chan_rx.skb[i]);
+	}
+
+rx_free:
+	ltq_dma_free(&ch_rx->dma);
+	return ret;
+}
+
+static void xrx200_hw_cleanup(struct xrx200_priv *priv)
+{
+	int i;
+
+	ltq_dma_free(&priv->chan_tx.dma);
+	ltq_dma_free(&priv->chan_rx.dma);
+
+	/* free the allocated RX ring */
+	for (i = 0; i < LTQ_DESC_NUM; i++)
+		dev_kfree_skb_any(priv->chan_rx.skb[i]);
+}
+
+static int xrx200_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct resource *res;
+	struct xrx200_priv *priv;
+	struct net_device *net_dev;
+	const u8 *mac;
+	int err;
+
+	/* alloc the network device */
+	net_dev = devm_alloc_etherdev(dev, sizeof(struct xrx200_priv));
+	if (!net_dev)
+		return -ENOMEM;
+
+	priv = netdev_priv(net_dev);
+	priv->net_dev = net_dev;
+	priv->dev = dev;
+
+	net_dev->netdev_ops = &xrx200_netdev_ops;
+	SET_NETDEV_DEV(net_dev, dev);
+	net_dev->min_mtu = ETH_ZLEN;
+	net_dev->max_mtu = XRX200_DMA_DATA_LEN;
+
+	/* load the memory ranges */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "failed to get resources\n");
+		return -ENOENT;
+	}
+
+	priv->pmac_reg = devm_ioremap_resource(dev, res);
+	if (!priv->pmac_reg) {
+		dev_err(dev, "failed to request and remap io ranges\n");
+		return -ENOMEM;
+	}
+
+	priv->chan_rx.dma.irq = platform_get_irq_byname(pdev, "rx");
+	if (priv->chan_rx.dma.irq < 0) {
+		dev_err(dev, "failed to get RX IRQ, %i\n",
+			priv->chan_rx.dma.irq);
+		return -ENOENT;
+	}
+	priv->chan_tx.dma.irq = platform_get_irq_byname(pdev, "tx");
+	if (priv->chan_tx.dma.irq < 0) {
+		dev_err(dev, "failed to get TX IRQ, %i\n",
+			priv->chan_tx.dma.irq);
+		return -ENOENT;
+	}
+
+	/* get the clock */
+	priv->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	mac = of_get_mac_address(np);
+	if (mac && is_valid_ether_addr(mac))
+		ether_addr_copy(net_dev->dev_addr, mac);
+	else
+		eth_hw_addr_random(net_dev);
+
+	/* bring up the dma engine and IP core */
+	err = xrx200_dma_init(priv);
+	if (err)
+		return err;
+
+	/* set IPG to 12 */
+	xrx200_pmac_mask(priv, PMAC_RX_IPG_MASK, 0xb, PMAC_RX_IPG);
+
+	/* enable status header, enable CRC */
+	xrx200_pmac_mask(priv, 0,
+			 PMAC_HD_CTL_RST | PMAC_HD_CTL_AST | PMAC_HD_CTL_RXSH |
+			 PMAC_HD_CTL_AS | PMAC_HD_CTL_AC | PMAC_HD_CTL_RC,
+			 PMAC_HD_CTL);
+
+	/* setup NAPI */
+	netif_napi_add(net_dev, &priv->chan_rx.napi, xrx200_poll_rx, 32);
+	netif_napi_add(net_dev, &priv->chan_tx.napi, xrx200_tx_housekeeping, 32);
+
+	platform_set_drvdata(pdev, priv);
+
+	err = register_netdev(net_dev);
+	if (err)
+		goto err_uninit_dma;
+	return err;
+
+err_uninit_dma:
+	xrx200_hw_cleanup(priv);
+
+	return 0;
+}
+
+static int xrx200_remove(struct platform_device *pdev)
+{
+	struct xrx200_priv *priv = platform_get_drvdata(pdev);
+	struct net_device *net_dev = priv->net_dev;
+
+	/* free stack related instances */
+	netif_stop_queue(net_dev);
+	netif_napi_del(&priv->chan_tx.napi);
+	netif_napi_del(&priv->chan_rx.napi);
+
+	/* remove the actual device */
+	unregister_netdev(net_dev);
+
+	/* shut down hardware */
+	xrx200_hw_cleanup(priv);
+
+	return 0;
+}
+
+static const struct of_device_id xrx200_match[] = {
+	{ .compatible = "lantiq,xrx200-net" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xrx200_match);
+
+static struct platform_driver xrx200_driver = {
+	.probe = xrx200_probe,
+	.remove = xrx200_remove,
+	.driver = {
+		.name = "lantiq,xrx200-net",
+		.of_match_table = xrx200_match,
+	},
+};
+
+module_platform_driver(xrx200_driver);
+
+MODULE_AUTHOR("John Crispin <john@phrozen.org>");
+MODULE_DESCRIPTION("Lantiq SoC XRX200 ethernet");
+MODULE_LICENSE("GPL");

include/net/dsa.h

@@ -35,6 +35,7 @@ enum dsa_tag_protocol {
 	DSA_TAG_PROTO_BRCM_PREPEND,
 	DSA_TAG_PROTO_DSA,
 	DSA_TAG_PROTO_EDSA,
+	DSA_TAG_PROTO_GSWIP,
 	DSA_TAG_PROTO_KSZ,
 	DSA_TAG_PROTO_LAN9303,
 	DSA_TAG_PROTO_MTK,

net/dsa/Kconfig

@@ -38,6 +38,9 @@ config NET_DSA_TAG_DSA
 config NET_DSA_TAG_EDSA
 	bool
 
+config NET_DSA_TAG_GSWIP
+	bool
+
 config NET_DSA_TAG_KSZ
 	bool
 

net/dsa/Makefile

@@ -9,6 +9,7 @@ dsa_core-$(CONFIG_NET_DSA_TAG_BRCM) += tag_brcm.o
 dsa_core-$(CONFIG_NET_DSA_TAG_BRCM_PREPEND) += tag_brcm.o
 dsa_core-$(CONFIG_NET_DSA_TAG_DSA) += tag_dsa.o
 dsa_core-$(CONFIG_NET_DSA_TAG_EDSA) += tag_edsa.o
+dsa_core-$(CONFIG_NET_DSA_TAG_GSWIP) += tag_gswip.o
 dsa_core-$(CONFIG_NET_DSA_TAG_KSZ) += tag_ksz.o
 dsa_core-$(CONFIG_NET_DSA_TAG_LAN9303) += tag_lan9303.o
 dsa_core-$(CONFIG_NET_DSA_TAG_MTK) += tag_mtk.o

net/dsa/dsa.c

@@ -52,6 +52,9 @@ const struct dsa_device_ops *dsa_device_ops[DSA_TAG_LAST] = {
 #ifdef CONFIG_NET_DSA_TAG_EDSA
 	[DSA_TAG_PROTO_EDSA] = &edsa_netdev_ops,
 #endif
+#ifdef CONFIG_NET_DSA_TAG_GSWIP
+	[DSA_TAG_PROTO_GSWIP] = &gswip_netdev_ops,
+#endif
 #ifdef CONFIG_NET_DSA_TAG_KSZ
 	[DSA_TAG_PROTO_KSZ] = &ksz_netdev_ops,
 #endif

net/dsa/dsa_priv.h

@@ -206,6 +206,9 @@ extern const struct dsa_device_ops dsa_netdev_ops;
 /* tag_edsa.c */
 extern const struct dsa_device_ops edsa_netdev_ops;
 
+/* tag_gswip.c */
+extern const struct dsa_device_ops gswip_netdev_ops;
+
 /* tag_ksz.c */
 extern const struct dsa_device_ops ksz_netdev_ops;
 

net/dsa/tag_gswip.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Intel / Lantiq GSWIP V2.0 PMAC tag support
+ *
+ * Copyright (C) 2017 - 2018 Hauke Mehrtens <hauke@hauke-m.de>
+ */
+
+#include <linux/bitops.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <net/dsa.h>
+
+#include "dsa_priv.h"
+
+#define GSWIP_TX_HEADER_LEN		4
+
+/* special tag in TX path header */
+/* Byte 0 */
+#define GSWIP_TX_SLPID_SHIFT		0	/* source port ID */
+#define  GSWIP_TX_SLPID_CPU		2
+#define  GSWIP_TX_SLPID_APP1		3
+#define  GSWIP_TX_SLPID_APP2		4
+#define  GSWIP_TX_SLPID_APP3		5
+#define  GSWIP_TX_SLPID_APP4		6
+#define  GSWIP_TX_SLPID_APP5		7
+
+/* Byte 1 */
+#define GSWIP_TX_CRCGEN_DIS		BIT(7)
+#define GSWIP_TX_DPID_SHIFT		0	/* destination group ID */
+#define  GSWIP_TX_DPID_ELAN		0
+#define  GSWIP_TX_DPID_EWAN		1
+#define  GSWIP_TX_DPID_CPU		2
+#define  GSWIP_TX_DPID_APP1		3
+#define  GSWIP_TX_DPID_APP2		4
+#define  GSWIP_TX_DPID_APP3		5
+#define  GSWIP_TX_DPID_APP4		6
+#define  GSWIP_TX_DPID_APP5		7
+
+/* Byte 2 */
+#define GSWIP_TX_PORT_MAP_EN		BIT(7)
+#define GSWIP_TX_PORT_MAP_SEL		BIT(6)
+#define GSWIP_TX_LRN_DIS		BIT(5)
+#define GSWIP_TX_CLASS_EN		BIT(4)
+#define GSWIP_TX_CLASS_SHIFT		0
+#define GSWIP_TX_CLASS_MASK		GENMASK(3, 0)
+
+/* Byte 3 */
+#define GSWIP_TX_DPID_EN		BIT(0)
+#define GSWIP_TX_PORT_MAP_SHIFT		1
+#define GSWIP_TX_PORT_MAP_MASK		GENMASK(6, 1)
+
+#define GSWIP_RX_HEADER_LEN	8
+
+/* special tag in RX path header */
+/* Byte 7 */
+#define GSWIP_RX_SPPID_SHIFT		4
+#define GSWIP_RX_SPPID_MASK		GENMASK(6, 4)
+
+static struct sk_buff *gswip_tag_xmit(struct sk_buff *skb,
+				      struct net_device *dev)
+{
+	struct dsa_port *dp = dsa_slave_to_port(dev);
+	int err;
+	u8 *gswip_tag;
+
+	err = skb_cow_head(skb, GSWIP_TX_HEADER_LEN);
+	if (err)
+		return NULL;
+
+	skb_push(skb, GSWIP_TX_HEADER_LEN);
+
+	gswip_tag = skb->data;
+	gswip_tag[0] = GSWIP_TX_SLPID_CPU;
+	gswip_tag[1] = GSWIP_TX_DPID_ELAN;
+	gswip_tag[2] = GSWIP_TX_PORT_MAP_EN | GSWIP_TX_PORT_MAP_SEL;
+	gswip_tag[3] = BIT(dp->index + GSWIP_TX_PORT_MAP_SHIFT) & GSWIP_TX_PORT_MAP_MASK;
+	gswip_tag[3] |= GSWIP_TX_DPID_EN;
+
+	return skb;
+}
+
+static struct sk_buff *gswip_tag_rcv(struct sk_buff *skb,
+				     struct net_device *dev,
+				     struct packet_type *pt)
+{
+	int port;
+	u8 *gswip_tag;
+
+	if (unlikely(!pskb_may_pull(skb, GSWIP_RX_HEADER_LEN)))
+		return NULL;
+
+	gswip_tag = skb->data - ETH_HLEN;
+
+	/* Get source port information */
+	port = (gswip_tag[7] & GSWIP_RX_SPPID_MASK) >> GSWIP_RX_SPPID_SHIFT;
+	skb->dev = dsa_master_find_slave(dev, 0, port);
+	if (!skb->dev)
+		return NULL;
+
+	/* remove GSWIP tag */
+	skb_pull_rcsum(skb, GSWIP_RX_HEADER_LEN);
+
+	return skb;
+}
+
+const struct dsa_device_ops gswip_netdev_ops = {
+	.xmit = gswip_tag_xmit,
+	.rcv = gswip_tag_rcv,
+};