Skip to content

L
linux
Commit d0fc2eaa authored by Kumar Gala's avatar Kumar Gala
Browse files
Options

powerpc/fsl: Refactor device bindings 

Moved Freescale SoC related bindings out of booting-without-of.txt and into
their own files.
Signed-off-by: default avatarKumar Gala <galak@kernel.crashing.org>
parent b93eeba4
Hide whitespace changes
Inline Side-by-side
Showing with 1077 additions and 1206 deletions
Documentation/powerpc/booting-without-of.txt
View file @ d0fc2eaa
...@@ -41,27 +41,12 @@ Table of Contents ...@@ -41,27 +41,12 @@ Table of Contents
VI - System-on-a-chip devices and nodes VI - System-on-a-chip devices and nodes
1) Defining child nodes of an SOC 1) Defining child nodes of an SOC
2) Representing devices without a current OF specification 2) Representing devices without a current OF specification
a) MDIO IO device a) PHY nodes
b) Gianfar-compatible ethernet nodes b) Interrupt controllers
c) PHY nodes c) CFI or JEDEC memory-mapped NOR flash
d) Interrupt controllers d) 4xx/Axon EMAC ethernet nodes
e) I2C e) Xilinx IP cores
f) Freescale SOC USB controllers f) USB EHCI controllers
g) Freescale SOC SEC Security Engines
h) Board Control and Status (BCSR)
i) Freescale QUICC Engine module (QE)
j) CFI or JEDEC memory-mapped NOR flash
k) Global Utilities Block
l) Freescale Communications Processor Module
m) Chipselect/Local Bus
n) 4xx/Axon EMAC ethernet nodes
o) Xilinx IP cores
p) Freescale Synchronous Serial Interface
q) USB EHCI controllers
r) Freescale Display Interface Unit
s) Freescale on board FPGA
t) Freescael MSI interrupt controller
u) Freescale General-purpose Timers Module
VII - Marvell Discovery mv64[345]6x System Controller chips VII - Marvell Discovery mv64[345]6x System Controller chips
1) The /system-controller node 1) The /system-controller node
...@@ -1250,80 +1235,7 @@ descriptions for the SOC devices for which new nodes have been ...@@ -1250,80 +1235,7 @@ descriptions for the SOC devices for which new nodes have been
defined; this list will expand as more and more SOC-containing defined; this list will expand as more and more SOC-containing
platforms are moved over to use the flattened-device-tree model. platforms are moved over to use the flattened-device-tree model.
a) MDIO IO device a) PHY nodes
The MDIO is a bus to which the PHY devices are connected. For each
device that exists on this bus, a child node should be created. See
the definition of the PHY node below for an example of how to define
a PHY.
Required properties:
- reg : Offset and length of the register set for the device
- compatible : Should define the compatible device type for the
mdio. Currently, this is most likely to be "fsl,gianfar-mdio"
Example:
mdio@24520 {
reg = <24520 20>;
compatible = "fsl,gianfar-mdio";
ethernet-phy@0 {
......
};
};
b) Gianfar-compatible ethernet nodes
Required properties:
- device_type : Should be "network"
- model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
- compatible : Should be "gianfar"
- reg : Offset and length of the register set for the device
- mac-address : List of bytes representing the ethernet address of
this controller
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- phy-handle : The phandle for the PHY connected to this ethernet
controller.
- fixed-link : <a b c d e> where a is emulated phy id - choose any,
but unique to the all specified fixed-links, b is duplex - 0 half,
1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
Recommended properties:
- phy-connection-type : a string naming the controller/PHY interface type,
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
"tbi", or "rtbi". This property is only really needed if the connection
is of type "rgmii-id", as all other connection types are detected by
hardware.
Example:
ethernet@24000 {
#size-cells = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <24000 1000>;
mac-address = [ 00 E0 0C 00 73 00 ];
interrupts = <d 3 e 3 12 3>;
interrupt-parent = <40000>;
phy-handle = <2452000>
};
c) PHY nodes
Required properties: Required properties:
...@@ -1351,7 +1263,7 @@ platforms are moved over to use the flattened-device-tree model. ...@@ -1351,7 +1263,7 @@ platforms are moved over to use the flattened-device-tree model.
}; };
d) Interrupt controllers b) Interrupt controllers
Some SOC devices contain interrupt controllers that are different Some SOC devices contain interrupt controllers that are different
from the standard Open PIC specification. The SOC device nodes for from the standard Open PIC specification. The SOC device nodes for
...@@ -1371,508 +1283,7 @@ platforms are moved over to use the flattened-device-tree model. ...@@ -1371,508 +1283,7 @@ platforms are moved over to use the flattened-device-tree model.
device_type = "open-pic"; device_type = "open-pic";
}; };
c) CFI or JEDEC memory-mapped NOR flash
e) I2C
Required properties :
- device_type : Should be "i2c"
- reg : Offset and length of the register set for the device
Recommended properties :
- compatible : Should be "fsl-i2c" for parts compatible with
Freescale I2C specifications.
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- dfsrr : boolean; if defined, indicates that this I2C device has
a digital filter sampling rate register
- fsl5200-clocking : boolean; if defined, indicated that this device
uses the FSL 5200 clocking mechanism.
Example :
i2c@3000 {
interrupt-parent = <40000>;
interrupts = <1b 3>;
reg = <3000 18>;
device_type = "i2c";
compatible = "fsl-i2c";
dfsrr;
};
f) Freescale SOC USB controllers
The device node for a USB controller that is part of a Freescale
SOC is as described in the document "Open Firmware Recommended
Practice : Universal Serial Bus" with the following modifications
and additions :
Required properties :
- compatible : Should be "fsl-usb2-mph" for multi port host USB
controllers, or "fsl-usb2-dr" for dual role USB controllers
- phy_type : For multi port host USB controllers, should be one of
"ulpi", or "serial". For dual role USB controllers, should be
one of "ulpi", "utmi", "utmi_wide", or "serial".
- reg : Offset and length of the register set for the device
- port0 : boolean; if defined, indicates port0 is connected for
fsl-usb2-mph compatible controllers. Either this property or
"port1" (or both) must be defined for "fsl-usb2-mph" compatible
controllers.
- port1 : boolean; if defined, indicates port1 is connected for
fsl-usb2-mph compatible controllers. Either this property or
"port0" (or both) must be defined for "fsl-usb2-mph" compatible
controllers.
- dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
controllers. Can be "host", "peripheral", or "otg". Default to
"host" if not defined for backward compatibility.
Recommended properties :
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
Example multi port host USB controller device node :
usb@22000 {
compatible = "fsl-usb2-mph";
reg = <22000 1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <700>;
interrupts = <27 1>;
phy_type = "ulpi";
port0;
port1;
};
Example dual role USB controller device node :
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <23000 1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <700>;
interrupts = <26 1>;
dr_mode = "otg";
phy = "ulpi";
};
g) Freescale SOC SEC Security Engines
Required properties:
- device_type : Should be "crypto"
- model : Model of the device. Should be "SEC1" or "SEC2"
- compatible : Should be "talitos"
- reg : Offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- num-channels : An integer representing the number of channels
available.
- channel-fifo-len : An integer representing the number of
descriptor pointers each channel fetch fifo can hold.
- exec-units-mask : The bitmask representing what execution units
(EUs) are available. It's a single 32-bit cell. EU information
should be encoded following the SEC's Descriptor Header Dword
EU_SEL0 field documentation, i.e. as follows:
bit 0 = reserved - should be 0
bit 1 = set if SEC has the ARC4 EU (AFEU)
bit 2 = set if SEC has the DES/3DES EU (DEU)
bit 3 = set if SEC has the message digest EU (MDEU)
bit 4 = set if SEC has the random number generator EU (RNG)
bit 5 = set if SEC has the public key EU (PKEU)
bit 6 = set if SEC has the AES EU (AESU)
bit 7 = set if SEC has the Kasumi EU (KEU)
bits 8 through 31 are reserved for future SEC EUs.
- descriptor-types-mask : The bitmask representing what descriptors
are available. It's a single 32-bit cell. Descriptor type
information should be encoded following the SEC's Descriptor
Header Dword DESC_TYPE field documentation, i.e. as follows:
bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type
bit 1 = set if SEC supports the ipsec_esp descriptor type
bit 2 = set if SEC supports the common_nonsnoop desc. type
bit 3 = set if SEC supports the 802.11i AES ccmp desc. type
bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type
bit 5 = set if SEC supports the srtp descriptor type
bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type
bit 7 = set if SEC supports the pkeu_assemble descriptor type
bit 8 = set if SEC supports the aesu_key_expand_output desc.type
bit 9 = set if SEC supports the pkeu_ptmul descriptor type
bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type
bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type
..and so on and so forth.
Example:
/* MPC8548E */
crypto@30000 {
device_type = "crypto";
model = "SEC2";
compatible = "talitos";
reg = <30000 10000>;
interrupts = <1d 3>;
interrupt-parent = <40000>;
num-channels = <4>;
channel-fifo-len = <18>;
exec-units-mask = <000000fe>;
descriptor-types-mask = <012b0ebf>;
};
h) Board Control and Status (BCSR)
Required properties:
- device_type : Should be "board-control"
- reg : Offset and length of the register set for the device
Example:
bcsr@f8000000 {
device_type = "board-control";
reg = <f8000000 8000>;
};
i) Freescale QUICC Engine module (QE)
This represents qe module that is installed on PowerQUICC II Pro.
NOTE: This is an interim binding; it should be updated to fit
in with the CPM binding later in this document.
Basically, it is a bus of devices, that could act more or less
as a complete entity (UCC, USB etc ). All of them should be siblings on
the "root" qe node, using the common properties from there.
The description below applies to the qe of MPC8360 and
more nodes and properties would be extended in the future.
i) Root QE device
Required properties:
- compatible : should be "fsl,qe";
- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
- reg : offset and length of the device registers.
- bus-frequency : the clock frequency for QUICC Engine.
Recommended properties
- brg-frequency : the internal clock source frequency for baud-rate
generators in Hz.
Example:
qe@e0100000 {
#address-cells = <1>;
#size-cells = <1>;
#interrupt-cells = <2>;
compatible = "fsl,qe";
ranges = <0 e0100000 00100000>;
reg = <e0100000 480>;
brg-frequency = <0>;
bus-frequency = <179A7B00>;
}
ii) SPI (Serial Peripheral Interface)
Required properties:
- cell-index : SPI controller index.
- compatible : should be "fsl,spi".
- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
- reg : Offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
Example:
spi@4c0 {
cell-index = <0>;
compatible = "fsl,spi";
reg = <4c0 40>;
interrupts = <82 0>;
interrupt-parent = <700>;
mode = "cpu";
};
iii) USB (Universal Serial Bus Controller)
Required properties:
- compatible : could be "qe_udc" or "fhci-hcd".
- mode : the could be "host" or "slave".
- reg : Offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
Example(slave):
usb@6c0 {
compatible = "qe_udc";
reg = <6c0 40>;
interrupts = <8b 0>;
interrupt-parent = <700>;
mode = "slave";
};
iv) UCC (Unified Communications Controllers)
Required properties:
- device_type : should be "network", "hldc", "uart", "transparent"
"bisync", "atm", or "serial".
- compatible : could be "ucc_geth" or "fsl_atm" and so on.
- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
- reg : Offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- pio-handle : The phandle for the Parallel I/O port configuration.
- port-number : for UART drivers, the port number to use, between 0 and 3.
This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
The port number is added to the minor number of the device. Unlike the
CPM UART driver, the port-number is required for the QE UART driver.
- soft-uart : for UART drivers, if specified this means the QE UART device
driver should use "Soft-UART" mode, which is needed on some SOCs that have
broken UART hardware. Soft-UART is provided via a microcode upload.
- rx-clock-name: the UCC receive clock source
"none": clock source is disabled
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
"clk1" through "clk24": clock source is CLK1-CLK24, respectively
- tx-clock-name: the UCC transmit clock source
"none": clock source is disabled
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
"clk1" through "clk24": clock source is CLK1-CLK24, respectively
The following two properties are deprecated. rx-clock has been replaced
with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
Drivers that currently use the deprecated properties should continue to
do so, in order to support older device trees, but they should be updated
to check for the new properties first.
- rx-clock : represents the UCC receive clock source.
0x00 : clock source is disabled;
0x1~0x10 : clock source is BRG1~BRG16 respectively;
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
- tx-clock: represents the UCC transmit clock source;
0x00 : clock source is disabled;
0x1~0x10 : clock source is BRG1~BRG16 respectively;
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
Required properties for network device_type:
- mac-address : list of bytes representing the ethernet address.
- phy-handle : The phandle for the PHY connected to this controller.
Recommended properties:
- phy-connection-type : a string naming the controller/PHY interface type,
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
"tbi", or "rtbi".
Example:
ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
cell-index = <1>;
reg = <2000 200>;
interrupts = <a0 0>;
interrupt-parent = <700>;
mac-address = [ 00 04 9f 00 23 23 ];
rx-clock = "none";
tx-clock = "clk9";
phy-handle = <212000>;
phy-connection-type = "gmii";
pio-handle = <140001>;
};
v) Parallel I/O Ports
This node configures Parallel I/O ports for CPUs with QE support.
The node should reside in the "soc" node of the tree. For each
device that using parallel I/O ports, a child node should be created.
See the definition of the Pin configuration nodes below for more
information.
Required properties:
- device_type : should be "par_io".
- reg : offset to the register set and its length.
- num-ports : number of Parallel I/O ports
Example:
par_io@1400 {
reg = <1400 100>;
#address-cells = <1>;
#size-cells = <0>;
device_type = "par_io";
num-ports = <7>;
ucc_pin@01 {
......
};
Note that "par_io" nodes are obsolete, and should not be used for
the new device trees. Instead, each Par I/O bank should be represented
via its own gpio-controller node:
Required properties:
- #gpio-cells : should be "2".
- compatible : should be "fsl,<chip>-qe-pario-bank",
"fsl,mpc8323-qe-pario-bank".
- reg : offset to the register set and its length.
- gpio-controller : node to identify gpio controllers.
Example:
qe_pio_a: gpio-controller@1400 {
#gpio-cells = <2>;
compatible = "fsl,mpc8360-qe-pario-bank",
"fsl,mpc8323-qe-pario-bank";
reg = <0x1400 0x18>;
gpio-controller;
};
qe_pio_e: gpio-controller@1460 {
#gpio-cells = <2>;
compatible = "fsl,mpc8360-qe-pario-bank",
"fsl,mpc8323-qe-pario-bank";
reg = <0x1460 0x18>;
gpio-controller;
};
vi) Pin configuration nodes
Required properties:
- linux,phandle : phandle of this node; likely referenced by a QE
device.
- pio-map : array of pin configurations. Each pin is defined by 6
integers. The six numbers are respectively: port, pin, dir,
open_drain, assignment, has_irq.
- port : port number of the pin; 0-6 represent port A-G in UM.
- pin : pin number in the port.
- dir : direction of the pin, should encode as follows:
0 = The pin is disabled
1 = The pin is an output
2 = The pin is an input
3 = The pin is I/O
- open_drain : indicates the pin is normal or wired-OR:
0 = The pin is actively driven as an output
1 = The pin is an open-drain driver. As an output, the pin is
driven active-low, otherwise it is three-stated.
- assignment : function number of the pin according to the Pin Assignment
tables in User Manual. Each pin can have up to 4 possible functions in
QE and two options for CPM.
- has_irq : indicates if the pin is used as source of external
interrupts.
Example:
ucc_pin@01 {
linux,phandle = <140001>;
pio-map = <
/* port pin dir open_drain assignment has_irq */
0 3 1 0 1 0 /* TxD0 */
0 4 1 0 1 0 /* TxD1 */
0 5 1 0 1 0 /* TxD2 */
0 6 1 0 1 0 /* TxD3 */
1 6 1 0 3 0 /* TxD4 */
1 7 1 0 1 0 /* TxD5 */
1 9 1 0 2 0 /* TxD6 */
1 a 1 0 2 0 /* TxD7 */
0 9 2 0 1 0 /* RxD0 */
0 a 2 0 1 0 /* RxD1 */
0 b 2 0 1 0 /* RxD2 */
0 c 2 0 1 0 /* RxD3 */
0 d 2 0 1 0 /* RxD4 */
1 1 2 0 2 0 /* RxD5 */
1 0 2 0 2 0 /* RxD6 */
1 4 2 0 2 0 /* RxD7 */
0 7 1 0 1 0 /* TX_EN */
0 8 1 0 1 0 /* TX_ER */
0 f 2 0 1 0 /* RX_DV */
0 10 2 0 1 0 /* RX_ER */
0 0 2 0 1 0 /* RX_CLK */
2 9 1 0 3 0 /* GTX_CLK - CLK10 */
2 8 2 0 1 0>; /* GTX125 - CLK9 */
};
vii) Multi-User RAM (MURAM)
Required properties:
- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
- mode : the could be "host" or "slave".
- ranges : Should be defined as specified in 1) to describe the
translation of MURAM addresses.
- data-only : sub-node which defines the address area under MURAM
bus that can be allocated as data/parameter
Example:
muram@10000 {
compatible = "fsl,qe-muram", "fsl,cpm-muram";
ranges = <0 00010000 0000c000>;
data-only@0{
compatible = "fsl,qe-muram-data",
"fsl,cpm-muram-data";
reg = <0 c000>;
};
};
viii) Uploaded QE firmware
If a new firwmare has been uploaded to the QE (usually by the
boot loader), then a 'firmware' child node should be added to the QE
node. This node provides information on the uploaded firmware that
device drivers may need.
Required properties:
- id: The string name of the firmware. This is taken from the 'id'
member of the qe_firmware structure of the uploaded firmware.
Device drivers can search this string to determine if the
firmware they want is already present.
- extended-modes: The Extended Modes bitfield, taken from the
firmware binary. It is a 64-bit number represented
as an array of two 32-bit numbers.
- virtual-traps: The virtual traps, taken from the firmware binary.
It is an array of 8 32-bit numbers.
Example:
firmware {
id = "Soft-UART";
extended-modes = <0 0>;
virtual-traps = <0 0 0 0 0 0 0 0>;
}
j) CFI or JEDEC memory-mapped NOR flash
Flash chips (Memory Technology Devices) are often used for solid state Flash chips (Memory Technology Devices) are often used for solid state
file systems on embedded devices. file systems on embedded devices.
...@@ -1936,310 +1347,7 @@ platforms are moved over to use the flattened-device-tree model. ...@@ -1936,310 +1347,7 @@ platforms are moved over to use the flattened-device-tree model.
}; };
}; };
k) Global Utilities Block d) 4xx/Axon EMAC ethernet nodes
The global utilities block controls power management, I/O device
enabling, power-on-reset configuration monitoring, general-purpose
I/O signal configuration, alternate function selection for multiplexed
signals, and clock control.
Required properties:
- compatible : Should define the compatible device type for
global-utilities.
- reg : Offset and length of the register set for the device.
Recommended properties:
- fsl,has-rstcr : Indicates that the global utilities register set
contains a functioning "reset control register" (i.e. the board
is wired to reset upon setting the HRESET_REQ bit in this register).
Example:
global-utilities@e0000 { /* global utilities block */
compatible = "fsl,mpc8548-guts";
reg = <e0000 1000>;
fsl,has-rstcr;
};
l) Freescale Communications Processor Module
NOTE: This is an interim binding, and will likely change slightly,
as more devices are supported. The QE bindings especially are
incomplete.
i) Root CPM node
Properties:
- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
- reg : A 48-byte region beginning with CPCR.
Example:
cpm@119c0 {
#address-cells = <1>;
#size-cells = <1>;
#interrupt-cells = <2>;
compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
reg = <119c0 30>;
}
ii) Properties common to mulitple CPM/QE devices
- fsl,cpm-command : This value is ORed with the opcode and command flag
to specify the device on which a CPM command operates.
- fsl,cpm-brg : Indicates which baud rate generator the device
is associated with. If absent, an unused BRG
should be dynamically allocated. If zero, the
device uses an external clock rather than a BRG.
- reg : Unless otherwise specified, the first resource represents the
scc/fcc/ucc registers, and the second represents the device's
parameter RAM region (if it has one).
iii) Serial
Currently defined compatibles:
- fsl,cpm1-smc-uart
- fsl,cpm2-smc-uart
- fsl,cpm1-scc-uart
- fsl,cpm2-scc-uart
- fsl,qe-uart
Example:
serial@11a00 {
device_type = "serial";
compatible = "fsl,mpc8272-scc-uart",
"fsl,cpm2-scc-uart";
reg = <11a00 20 8000 100>;
interrupts = <28 8>;
interrupt-parent = <&PIC>;
fsl,cpm-brg = <1>;
fsl,cpm-command = <00800000>;
};
iii) Network
Currently defined compatibles:
- fsl,cpm1-scc-enet
- fsl,cpm2-scc-enet
- fsl,cpm1-fec-enet
- fsl,cpm2-fcc-enet (third resource is GFEMR)
- fsl,qe-enet
Example:
ethernet@11300 {
device_type = "network";
compatible = "fsl,mpc8272-fcc-enet",
"fsl,cpm2-fcc-enet";
reg = <11300 20 8400 100 11390 1>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <20 8>;
interrupt-parent = <&PIC>;
phy-handle = <&PHY0>;
fsl,cpm-command = <12000300>;
};
iv) MDIO
Currently defined compatibles:
fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
fsl,cpm2-mdio-bitbang (reg is port C registers)
Properties for fsl,cpm2-mdio-bitbang:
fsl,mdio-pin : pin of port C controlling mdio data
fsl,mdc-pin : pin of port C controlling mdio clock
Example:
mdio@10d40 {
device_type = "mdio";
compatible = "fsl,mpc8272ads-mdio-bitbang",
"fsl,mpc8272-mdio-bitbang",
"fsl,cpm2-mdio-bitbang";
reg = <10d40 14>;
#address-cells = <1>;
#size-cells = <0>;
fsl,mdio-pin = <12>;
fsl,mdc-pin = <13>;
};
v) Baud Rate Generators
Currently defined compatibles:
fsl,cpm-brg
fsl,cpm1-brg
fsl,cpm2-brg
Properties:
- reg : There may be an arbitrary number of reg resources; BRG
numbers are assigned to these in order.
- clock-frequency : Specifies the base frequency driving
the BRG.
Example:
brg@119f0 {
compatible = "fsl,mpc8272-brg",
"fsl,cpm2-brg",
"fsl,cpm-brg";
reg = <119f0 10 115f0 10>;
clock-frequency = <d#25000000>;
};
vi) Interrupt Controllers
Currently defined compatibles:
- fsl,cpm1-pic
- only one interrupt cell
- fsl,pq1-pic
- fsl,cpm2-pic
- second interrupt cell is level/sense:
- 2 is falling edge
- 8 is active low
Example:
interrupt-controller@10c00 {
#interrupt-cells = <2>;
interrupt-controller;
reg = <10c00 80>;
compatible = "mpc8272-pic", "fsl,cpm2-pic";
};
vii) USB (Universal Serial Bus Controller)
Properties:
- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
Example:
usb@11bc0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,cpm2-usb";
reg = <11b60 18 8b00 100>;
interrupts = <b 8>;
interrupt-parent = <&PIC>;
fsl,cpm-command = <2e600000>;
};
viii) Multi-User RAM (MURAM)
The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
Ranges must be set up subject to the following restrictions:
- Children's reg nodes must be offsets from the start of all muram, even
if the user-data area does not begin at zero.
- If multiple range entries are used, the difference between the parent
address and the child address must be the same in all, so that a single
mapping can cover them all while maintaining the ability to determine
CPM-side offsets with pointer subtraction. It is recommended that
multiple range entries not be used.
- A child address of zero must be translatable, even if no reg resources
contain it.
A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
indicate the portion of muram that is usable by the OS for arbitrary
purposes. The data node may have an arbitrary number of reg resources,
all of which contribute to the allocatable muram pool.
Example, based on mpc8272:
muram@0 {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 10000>;
data@0 {
compatible = "fsl,cpm-muram-data";
reg = <0 2000 9800 800>;
};
};
x) I2C
The I2C controller is expressed as a bus under the CPM node.
Properties:
- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c"
- reg : On CPM2 devices, the second resource doesn't specify the I2C
Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM
(typically 0x8afc 0x2).
- #address-cells : Should be one. The cell is the i2c device address with
the r/w bit set to zero.
- #size-cells : Should be zero.
- clock-frequency : Can be used to set the i2c clock frequency. If
unspecified, a default frequency of 60kHz is being used.
The following two properties are deprecated. They are only used by legacy
i2c drivers to find the bus to probe:
- linux,i2c-index : Can be used to hard code an i2c bus number. By default,
the bus number is dynamically assigned by the i2c core.
- linux,i2c-class : Can be used to override the i2c class. The class is used
by legacy i2c device drivers to find a bus in a specific context like
system management, video or sound. By default, I2C_CLASS_HWMON (1) is
being used. The definition of the classes can be found in
include/i2c/i2c.h
Example, based on mpc823:
i2c@860 {
compatible = "fsl,mpc823-i2c",
"fsl,cpm1-i2c";
reg = <0x860 0x20 0x3c80 0x30>;
interrupts = <16>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-command = <0x10>;
#address-cells = <1>;
#size-cells = <0>;
rtc@68 {
compatible = "dallas,ds1307";
reg = <0x68>;
};
};
m) Chipselect/Local Bus
Properties:
- name : Should be localbus
- #address-cells : Should be either two or three. The first cell is the
chipselect number, and the remaining cells are the
offset into the chipselect.
- #size-cells : Either one or two, depending on how large each chipselect
can be.
- ranges : Each range corresponds to a single chipselect, and cover
the entire access window as configured.
Example:
localbus@f0010100 {
compatible = "fsl,mpc8272-localbus",
"fsl,pq2-localbus";
#address-cells = <2>;
#size-cells = <1>;
reg = <f0010100 40>;
ranges = <0 0 fe000000 02000000
1 0 f4500000 00008000>;
flash@0,0 {
compatible = "jedec-flash";
reg = <0 0 2000000>;
bank-width = <4>;
device-width = <1>;
};
board-control@1,0 {
reg = <1 0 20>;
compatible = "fsl,mpc8272ads-bcsr";
};
};
n) 4xx/Axon EMAC ethernet nodes
The EMAC ethernet controller in IBM and AMCC 4xx chips, and also The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
the Axon bridge. To operate this needs to interact with a ths the Axon bridge. To operate this needs to interact with a ths
...@@ -2387,7 +1495,7 @@ platforms are moved over to use the flattened-device-tree model. ...@@ -2387,7 +1495,7 @@ platforms are moved over to use the flattened-device-tree model.
available. available.
For Axon: 0x0000012a For Axon: 0x0000012a
o) Xilinx IP cores e) Xilinx IP cores
The Xilinx EDK toolchain ships with a set of IP cores (devices) for use The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range
...@@ -2681,206 +1789,7 @@ platforms are moved over to use the flattened-device-tree model. ...@@ -2681,206 +1789,7 @@ platforms are moved over to use the flattened-device-tree model.
- reg-offset : A value of 3 is required - reg-offset : A value of 3 is required
- reg-shift : A value of 2 is required - reg-shift : A value of 2 is required
f) USB EHCI controllers
p) Freescale Synchronous Serial Interface
The SSI is a serial device that communicates with audio codecs. It can
be programmed in AC97, I2S, left-justified, or right-justified modes.
Required properties:
- compatible : compatible list, containing "fsl,ssi"
- cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on
- reg : offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and
level information for the interrupt. This should be
encoded based on the information in section 2)
depending on the type of interrupt controller you
have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- fsl,mode : the operating mode for the SSI interface
"i2s-slave" - I2S mode, SSI is clock slave
"i2s-master" - I2S mode, SSI is clock master
"lj-slave" - left-justified mode, SSI is clock slave
"lj-master" - l.j. mode, SSI is clock master
"rj-slave" - right-justified mode, SSI is clock slave
"rj-master" - r.j., SSI is clock master
"ac97-slave" - AC97 mode, SSI is clock slave
"ac97-master" - AC97 mode, SSI is clock master
Optional properties:
- codec-handle : phandle to a 'codec' node that defines an audio
codec connected to this SSI. This node is typically
a child of an I2C or other control node.
Child 'codec' node required properties:
- compatible : compatible list, contains the name of the codec
Child 'codec' node optional properties:
- clock-frequency : The frequency of the input clock, which typically
comes from an on-board dedicated oscillator.
* Freescale 83xx DMA Controller
Freescale PowerPC 83xx have on chip general purpose DMA controllers.
Required properties:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-dma", where CHIP is the processor
(mpc8349, mpc8360, etc.) and the second is
"fsl,elo-dma"
- reg : <registers mapping for DMA general status reg>
- ranges : Should be defined as specified in 1) to describe the
DMA controller channels.
- cell-index : controller index. 0 for controller @ 0x8100
- interrupts : <interrupt mapping for DMA IRQ>
- interrupt-parent : optional, if needed for interrupt mapping
- DMA channel nodes:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-dma-channel", where CHIP is the processor
(mpc8349, mpc8350, etc.) and the second is
"fsl,elo-dma-channel"
- reg : <registers mapping for channel>
- cell-index : dma channel index starts at 0.
Optional properties:
- interrupts : <interrupt mapping for DMA channel IRQ>
(on 83xx this is expected to be identical to
the interrupts property of the parent node)
- interrupt-parent : optional, if needed for interrupt mapping
Example:
dma@82a8 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
reg = <82a8 4>;
ranges = <0 8100 1a4>;
interrupt-parent = <&ipic>;
interrupts = <47 8>;
cell-index = <0>;
dma-channel@0 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
cell-index = <0>;
reg = <0 80>;
};
dma-channel@80 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
cell-index = <1>;
reg = <80 80>;
};
dma-channel@100 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
cell-index = <2>;
reg = <100 80>;
};
dma-channel@180 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
cell-index = <3>;
reg = <180 80>;
};
};
* Freescale 85xx/86xx DMA Controller
Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers.
Required properties:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-dma", where CHIP is the processor
(mpc8540, mpc8540, etc.) and the second is
"fsl,eloplus-dma"
- reg : <registers mapping for DMA general status reg>
- cell-index : controller index. 0 for controller @ 0x21000,
1 for controller @ 0xc000
- ranges : Should be defined as specified in 1) to describe the
DMA controller channels.
- DMA channel nodes:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-dma-channel", where CHIP is the processor
(mpc8540, mpc8560, etc.) and the second is
"fsl,eloplus-dma-channel"
- cell-index : dma channel index starts at 0.
- reg : <registers mapping for channel>
- interrupts : <interrupt mapping for DMA channel IRQ>
- interrupt-parent : optional, if needed for interrupt mapping
Example:
dma@21300 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
reg = <21300 4>;
ranges = <0 21100 200>;
cell-index = <0>;
dma-channel@0 {
compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
reg = <0 80>;
cell-index = <0>;
interrupt-parent = <&mpic>;
interrupts = <14 2>;
};
dma-channel@80 {
compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
reg = <80 80>;
cell-index = <1>;
interrupt-parent = <&mpic>;
interrupts = <15 2>;
};
dma-channel@100 {
compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
reg = <100 80>;
cell-index = <2>;
interrupt-parent = <&mpic>;
interrupts = <16 2>;
};
dma-channel@180 {
compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
reg = <180 80>;
cell-index = <3>;
interrupt-parent = <&mpic>;
interrupts = <17 2>;
};
};
* Freescale 8xxx/3.0 Gb/s SATA nodes
SATA nodes are defined to describe on-chip Serial ATA controllers.
Each SATA port should have its own node.
Required properties:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-sata", where CHIP is the processor
(mpc8315, mpc8379, etc.) and the second is
"fsl,pq-sata"
- interrupts : <interrupt mapping for SATA IRQ>
- cell-index : controller index.
1 for controller @ 0x18000
2 for controller @ 0x19000
3 for controller @ 0x1a000
4 for controller @ 0x1b000
Optional properties:
- interrupt-parent : optional, if needed for interrupt mapping
- reg : <registers mapping>
Example:
sata@18000 {
compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
reg = <0x18000 0x1000>;
cell-index = <1>;
interrupts = <2c 8>;
interrupt-parent = < &ipic >;
};
q) USB EHCI controllers
Required properties: Required properties:
- compatible : should be "usb-ehci". - compatible : should be "usb-ehci".
...@@ -2906,109 +1815,6 @@ platforms are moved over to use the flattened-device-tree model. ...@@ -2906,109 +1815,6 @@ platforms are moved over to use the flattened-device-tree model.
big-endian; big-endian;
}; };
r) Freescale Display Interface Unit
The Freescale DIU is a LCD controller, with proper hardware, it can also
drive DVI monitors.
Required properties:
- compatible : should be "fsl-diu".
- reg : should contain at least address and length of the DIU register
set.
- Interrupts : one DIU interrupt should be describe here.
Example (MPC8610HPCD)
display@2c000 {
compatible = "fsl,diu";
reg = <0x2c000 100>;
interrupts = <72 2>;
interrupt-parent = <&mpic>;
};
s) Freescale on board FPGA
This is the memory-mapped registers for on board FPGA.
Required properities:
- compatible : should be "fsl,fpga-pixis".
- reg : should contain the address and the lenght of the FPPGA register
set.
Example (MPC8610HPCD)
board-control@e8000000 {
compatible = "fsl,fpga-pixis";
reg = <0xe8000000 32>;
};
t) Freescale MSI interrupt controller
Reguired properities:
- compatible : compatible list, contains 2 entries,
first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572,
etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on
the parent type.
- reg : should contain the address and the length of the shared message
interrupt register set.
- msi-available-ranges: use <start count> style section to define which
msi interrupt can be used in the 256 msi interrupts. This property is
optional, without this, all the 256 MSI interrupts can be used.
- interrupts : each one of the interrupts here is one entry per 32 MSIs,
and routed to the host interrupt controller. the interrupts should
be set as edge sensitive.
- interrupt-parent: the phandle for the interrupt controller
that services interrupts for this device. for 83xx cpu, the interrupts
are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed
to MPIC.
Example
msi@41600 {
compatible = "fsl,mpc8610-msi", "fsl,mpic-msi";
reg = <0x41600 0x80>;
msi-available-ranges = <0 0x100>;
interrupts = <
0xe0 0
0xe1 0
0xe2 0
0xe3 0
0xe4 0
0xe5 0
0xe6 0
0xe7 0>;
interrupt-parent = <&mpic>;
};
u) Freescale General-purpose Timers Module
Required properties:
- compatible : should be
"fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
"fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
"fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
- reg : should contain gtm registers location and length (0x40).
- interrupts : should contain four interrupts.
- interrupt-parent : interrupt source phandle.
- clock-frequency : specifies the frequency driving the timer.
Example:
timer@500 {
compatible = "fsl,mpc8360-gtm", "fsl,gtm";
reg = <0x500 0x40>;
interrupts = <90 8 78 8 84 8 72 8>;
interrupt-parent = <&ipic>;
/* filled by u-boot */
clock-frequency = <0>;
};
timer@440 {
compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
reg = <0x440 0x40>;
interrupts = <12 13 14 15>;
interrupt-parent = <&qeic>;
/* filled by u-boot */
clock-frequency = <0>;
};
VII - Marvell Discovery mv64[345]6x System Controller chips VII - Marvell Discovery mv64[345]6x System Controller chips
=========================================================== ===========================================================
......
Documentation/powerpc/dts-bindings/fsl/board.txt 0 → 100644
View file @ d0fc2eaa
* Board Control and Status (BCSR)
Required properties:
- device_type : Should be "board-control"
- reg : Offset and length of the register set for the device
Example:
bcsr@f8000000 {
device_type = "board-control";
reg = <f8000000 8000>;
};
* Freescale on board FPGA
This is the memory-mapped registers for on board FPGA.
Required properities:
- compatible : should be "fsl,fpga-pixis".
- reg : should contain the address and the lenght of the FPPGA register
set.
Example (MPC8610HPCD):
board-control@e8000000 {
compatible = "fsl,fpga-pixis";
reg = <0xe8000000 32>;
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt 0 → 100644
View file @ d0fc2eaa
* Freescale Communications Processor Module
NOTE: This is an interim binding, and will likely change slightly,
as more devices are supported. The QE bindings especially are
incomplete.
* Root CPM node
Properties:
- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
- reg : A 48-byte region beginning with CPCR.
Example:
cpm@119c0 {
#address-cells = <1>;
#size-cells = <1>;
#interrupt-cells = <2>;
compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
reg = <119c0 30>;
}
* Properties common to mulitple CPM/QE devices
- fsl,cpm-command : This value is ORed with the opcode and command flag
to specify the device on which a CPM command operates.
- fsl,cpm-brg : Indicates which baud rate generator the device
is associated with. If absent, an unused BRG
should be dynamically allocated. If zero, the
device uses an external clock rather than a BRG.
- reg : Unless otherwise specified, the first resource represents the
scc/fcc/ucc registers, and the second represents the device's
parameter RAM region (if it has one).
* Multi-User RAM (MURAM)
The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
Ranges must be set up subject to the following restrictions:
- Children's reg nodes must be offsets from the start of all muram, even
if the user-data area does not begin at zero.
- If multiple range entries are used, the difference between the parent
address and the child address must be the same in all, so that a single
mapping can cover them all while maintaining the ability to determine
CPM-side offsets with pointer subtraction. It is recommended that
multiple range entries not be used.
- A child address of zero must be translatable, even if no reg resources
contain it.
A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
indicate the portion of muram that is usable by the OS for arbitrary
purposes. The data node may have an arbitrary number of reg resources,
all of which contribute to the allocatable muram pool.
Example, based on mpc8272:
muram@0 {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 10000>;
data@0 {
compatible = "fsl,cpm-muram-data";
reg = <0 2000 9800 800>;
};
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt 0 → 100644
View file @ d0fc2eaa
* Baud Rate Generators
Currently defined compatibles:
fsl,cpm-brg
fsl,cpm1-brg
fsl,cpm2-brg
Properties:
- reg : There may be an arbitrary number of reg resources; BRG
numbers are assigned to these in order.
- clock-frequency : Specifies the base frequency driving
the BRG.
Example:
brg@119f0 {
compatible = "fsl,mpc8272-brg",
"fsl,cpm2-brg",
"fsl,cpm-brg";
reg = <119f0 10 115f0 10>;
clock-frequency = <d#25000000>;
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt 0 → 100644
View file @ d0fc2eaa
* I2C
The I2C controller is expressed as a bus under the CPM node.
Properties:
- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c"
- reg : On CPM2 devices, the second resource doesn't specify the I2C
Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM
(typically 0x8afc 0x2).
- #address-cells : Should be one. The cell is the i2c device address with
the r/w bit set to zero.
- #size-cells : Should be zero.
- clock-frequency : Can be used to set the i2c clock frequency. If
unspecified, a default frequency of 60kHz is being used.
The following two properties are deprecated. They are only used by legacy
i2c drivers to find the bus to probe:
- linux,i2c-index : Can be used to hard code an i2c bus number. By default,
the bus number is dynamically assigned by the i2c core.
- linux,i2c-class : Can be used to override the i2c class. The class is used
by legacy i2c device drivers to find a bus in a specific context like
system management, video or sound. By default, I2C_CLASS_HWMON (1) is
being used. The definition of the classes can be found in
include/i2c/i2c.h
Example, based on mpc823:
i2c@860 {
compatible = "fsl,mpc823-i2c",
"fsl,cpm1-i2c";
reg = <0x860 0x20 0x3c80 0x30>;
interrupts = <16>;
interrupt-parent = <&CPM_PIC>;
fsl,cpm-command = <0x10>;
#address-cells = <1>;
#size-cells = <0>;
rtc@68 {
compatible = "dallas,ds1307";
reg = <0x68>;
};
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt 0 → 100644
View file @ d0fc2eaa
* Interrupt Controllers
Currently defined compatibles:
- fsl,cpm1-pic
- only one interrupt cell
- fsl,pq1-pic
- fsl,cpm2-pic
- second interrupt cell is level/sense:
- 2 is falling edge
- 8 is active low
Example:
interrupt-controller@10c00 {
#interrupt-cells = <2>;
interrupt-controller;
reg = <10c00 80>;
compatible = "mpc8272-pic", "fsl,cpm2-pic";
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt 0 → 100644
View file @ d0fc2eaa
* USB (Universal Serial Bus Controller)
Properties:
- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
Example:
usb@11bc0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,cpm2-usb";
reg = <11b60 18 8b00 100>;
interrupts = <b 8>;
interrupt-parent = <&PIC>;
fsl,cpm-command = <2e600000>;
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt 0 → 100644
View file @ d0fc2eaa
* Network
Currently defined compatibles:
- fsl,cpm1-scc-enet
- fsl,cpm2-scc-enet
- fsl,cpm1-fec-enet
- fsl,cpm2-fcc-enet (third resource is GFEMR)
- fsl,qe-enet
Example:
ethernet@11300 {
device_type = "network";
compatible = "fsl,mpc8272-fcc-enet",
"fsl,cpm2-fcc-enet";
reg = <11300 20 8400 100 11390 1>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <20 8>;
interrupt-parent = <&PIC>;
phy-handle = <&PHY0>;
fsl,cpm-command = <12000300>;
};
* MDIO
Currently defined compatibles:
fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
fsl,cpm2-mdio-bitbang (reg is port C registers)
Properties for fsl,cpm2-mdio-bitbang:
fsl,mdio-pin : pin of port C controlling mdio data
fsl,mdc-pin : pin of port C controlling mdio clock
Example:
mdio@10d40 {
device_type = "mdio";
compatible = "fsl,mpc8272ads-mdio-bitbang",
"fsl,mpc8272-mdio-bitbang",
"fsl,cpm2-mdio-bitbang";
reg = <10d40 14>;
#address-cells = <1>;
#size-cells = <0>;
fsl,mdio-pin = <12>;
fsl,mdc-pin = <13>;
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt 0 → 100644
View file @ d0fc2eaa
* Freescale QUICC Engine module (QE)
This represents qe module that is installed on PowerQUICC II Pro.
NOTE: This is an interim binding; it should be updated to fit
in with the CPM binding later in this document.
Basically, it is a bus of devices, that could act more or less
as a complete entity (UCC, USB etc ). All of them should be siblings on
the "root" qe node, using the common properties from there.
The description below applies to the qe of MPC8360 and
more nodes and properties would be extended in the future.
i) Root QE device
Required properties:
- compatible : should be "fsl,qe";
- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
- reg : offset and length of the device registers.
- bus-frequency : the clock frequency for QUICC Engine.
Recommended properties
- brg-frequency : the internal clock source frequency for baud-rate
generators in Hz.
Example:
qe@e0100000 {
#address-cells = <1>;
#size-cells = <1>;
#interrupt-cells = <2>;
compatible = "fsl,qe";
ranges = <0 e0100000 00100000>;
reg = <e0100000 480>;
brg-frequency = <0>;
bus-frequency = <179A7B00>;
}
* Multi-User RAM (MURAM)
Required properties:
- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
- mode : the could be "host" or "slave".
- ranges : Should be defined as specified in 1) to describe the
translation of MURAM addresses.
- data-only : sub-node which defines the address area under MURAM
bus that can be allocated as data/parameter
Example:
muram@10000 {
compatible = "fsl,qe-muram", "fsl,cpm-muram";
ranges = <0 00010000 0000c000>;
data-only@0{
compatible = "fsl,qe-muram-data",
"fsl,cpm-muram-data";
reg = <0 c000>;
};
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt 0 → 100644
View file @ d0fc2eaa
* Uploaded QE firmware
If a new firwmare has been uploaded to the QE (usually by the
boot loader), then a 'firmware' child node should be added to the QE
node. This node provides information on the uploaded firmware that
device drivers may need.
Required properties:
- id: The string name of the firmware. This is taken from the 'id'
member of the qe_firmware structure of the uploaded firmware.
Device drivers can search this string to determine if the
firmware they want is already present.
- extended-modes: The Extended Modes bitfield, taken from the
firmware binary. It is a 64-bit number represented
as an array of two 32-bit numbers.
- virtual-traps: The virtual traps, taken from the firmware binary.
It is an array of 8 32-bit numbers.
Example:
firmware {
id = "Soft-UART";
extended-modes = <0 0>;
virtual-traps = <0 0 0 0 0 0 0 0>;
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt 0 → 100644
View file @ d0fc2eaa
* Parallel I/O Ports
This node configures Parallel I/O ports for CPUs with QE support.
The node should reside in the "soc" node of the tree. For each
device that using parallel I/O ports, a child node should be created.
See the definition of the Pin configuration nodes below for more
information.
Required properties:
- device_type : should be "par_io".
- reg : offset to the register set and its length.
- num-ports : number of Parallel I/O ports
Example:
par_io@1400 {
reg = <1400 100>;
#address-cells = <1>;
#size-cells = <0>;
device_type = "par_io";
num-ports = <7>;
ucc_pin@01 {
......
};
Note that "par_io" nodes are obsolete, and should not be used for
the new device trees. Instead, each Par I/O bank should be represented
via its own gpio-controller node:
Required properties:
- #gpio-cells : should be "2".
- compatible : should be "fsl,<chip>-qe-pario-bank",
"fsl,mpc8323-qe-pario-bank".
- reg : offset to the register set and its length.
- gpio-controller : node to identify gpio controllers.
Example:
qe_pio_a: gpio-controller@1400 {
#gpio-cells = <2>;
compatible = "fsl,mpc8360-qe-pario-bank",
"fsl,mpc8323-qe-pario-bank";
reg = <0x1400 0x18>;
gpio-controller;
};
qe_pio_e: gpio-controller@1460 {
#gpio-cells = <2>;
compatible = "fsl,mpc8360-qe-pario-bank",
"fsl,mpc8323-qe-pario-bank";
reg = <0x1460 0x18>;
gpio-controller;
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt 0 → 100644
View file @ d0fc2eaa
* Pin configuration nodes
Required properties:
- linux,phandle : phandle of this node; likely referenced by a QE
device.
- pio-map : array of pin configurations. Each pin is defined by 6
integers. The six numbers are respectively: port, pin, dir,
open_drain, assignment, has_irq.
- port : port number of the pin; 0-6 represent port A-G in UM.
- pin : pin number in the port.
- dir : direction of the pin, should encode as follows:
0 = The pin is disabled
1 = The pin is an output
2 = The pin is an input
3 = The pin is I/O
- open_drain : indicates the pin is normal or wired-OR:
0 = The pin is actively driven as an output
1 = The pin is an open-drain driver. As an output, the pin is
driven active-low, otherwise it is three-stated.
- assignment : function number of the pin according to the Pin Assignment
tables in User Manual. Each pin can have up to 4 possible functions in
QE and two options for CPM.
- has_irq : indicates if the pin is used as source of external
interrupts.
Example:
ucc_pin@01 {
linux,phandle = <140001>;
pio-map = <
/* port pin dir open_drain assignment has_irq */
0 3 1 0 1 0 /* TxD0 */
0 4 1 0 1 0 /* TxD1 */
0 5 1 0 1 0 /* TxD2 */
0 6 1 0 1 0 /* TxD3 */
1 6 1 0 3 0 /* TxD4 */
1 7 1 0 1 0 /* TxD5 */
1 9 1 0 2 0 /* TxD6 */
1 a 1 0 2 0 /* TxD7 */
0 9 2 0 1 0 /* RxD0 */
0 a 2 0 1 0 /* RxD1 */
0 b 2 0 1 0 /* RxD2 */
0 c 2 0 1 0 /* RxD3 */
0 d 2 0 1 0 /* RxD4 */
1 1 2 0 2 0 /* RxD5 */
1 0 2 0 2 0 /* RxD6 */
1 4 2 0 2 0 /* RxD7 */
0 7 1 0 1 0 /* TX_EN */
0 8 1 0 1 0 /* TX_ER */
0 f 2 0 1 0 /* RX_DV */
0 10 2 0 1 0 /* RX_ER */
0 0 2 0 1 0 /* RX_CLK */
2 9 1 0 3 0 /* GTX_CLK - CLK10 */
2 8 2 0 1 0>; /* GTX125 - CLK9 */
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt 0 → 100644
View file @ d0fc2eaa
* UCC (Unified Communications Controllers)
Required properties:
- device_type : should be "network", "hldc", "uart", "transparent"
"bisync", "atm", or "serial".
- compatible : could be "ucc_geth" or "fsl_atm" and so on.
- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
- reg : Offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- pio-handle : The phandle for the Parallel I/O port configuration.
- port-number : for UART drivers, the port number to use, between 0 and 3.
This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
The port number is added to the minor number of the device. Unlike the
CPM UART driver, the port-number is required for the QE UART driver.
- soft-uart : for UART drivers, if specified this means the QE UART device
driver should use "Soft-UART" mode, which is needed on some SOCs that have
broken UART hardware. Soft-UART is provided via a microcode upload.
- rx-clock-name: the UCC receive clock source
"none": clock source is disabled
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
"clk1" through "clk24": clock source is CLK1-CLK24, respectively
- tx-clock-name: the UCC transmit clock source
"none": clock source is disabled
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
"clk1" through "clk24": clock source is CLK1-CLK24, respectively
The following two properties are deprecated. rx-clock has been replaced
with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
Drivers that currently use the deprecated properties should continue to
do so, in order to support older device trees, but they should be updated
to check for the new properties first.
- rx-clock : represents the UCC receive clock source.
0x00 : clock source is disabled;
0x1~0x10 : clock source is BRG1~BRG16 respectively;
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
- tx-clock: represents the UCC transmit clock source;
0x00 : clock source is disabled;
0x1~0x10 : clock source is BRG1~BRG16 respectively;
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
Required properties for network device_type:
- mac-address : list of bytes representing the ethernet address.
- phy-handle : The phandle for the PHY connected to this controller.
Recommended properties:
- phy-connection-type : a string naming the controller/PHY interface type,
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
"tbi", or "rtbi".
Example:
ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
cell-index = <1>;
reg = <2000 200>;
interrupts = <a0 0>;
interrupt-parent = <700>;
mac-address = [ 00 04 9f 00 23 23 ];
rx-clock = "none";
tx-clock = "clk9";
phy-handle = <212000>;
phy-connection-type = "gmii";
pio-handle = <140001>;
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt 0 → 100644
View file @ d0fc2eaa
* USB (Universal Serial Bus Controller)
Required properties:
- compatible : could be "qe_udc" or "fhci-hcd".
- mode : the could be "host" or "slave".
- reg : Offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
Example(slave):
usb@6c0 {
compatible = "qe_udc";
reg = <6c0 40>;
interrupts = <8b 0>;
interrupt-parent = <700>;
mode = "slave";
};
Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt 0 → 100644
View file @ d0fc2eaa
* Serial
Currently defined compatibles:
- fsl,cpm1-smc-uart
- fsl,cpm2-smc-uart
- fsl,cpm1-scc-uart
- fsl,cpm2-scc-uart
- fsl,qe-uart
Example:
serial@11a00 {
device_type = "serial";
compatible = "fsl,mpc8272-scc-uart",
"fsl,cpm2-scc-uart";
reg = <11a00 20 8000 100>;
interrupts = <28 8>;
interrupt-parent = <&PIC>;
fsl,cpm-brg = <1>;
fsl,cpm-command = <00800000>;
};
Documentation/powerpc/dts-bindings/fsl/diu.txt 0 → 100644
View file @ d0fc2eaa
* Freescale Display Interface Unit
The Freescale DIU is a LCD controller, with proper hardware, it can also
drive DVI monitors.
Required properties:
- compatible : should be "fsl-diu".
- reg : should contain at least address and length of the DIU register
set.
- Interrupts : one DIU interrupt should be describe here.
Example (MPC8610HPCD):
display@2c000 {
compatible = "fsl,diu";
reg = <0x2c000 100>;
interrupts = <72 2>;
interrupt-parent = <&mpic>;
};
Documentation/powerpc/dts-bindings/fsl/dma.txt 0 → 100644
View file @ d0fc2eaa
* Freescale 83xx DMA Controller
Freescale PowerPC 83xx have on chip general purpose DMA controllers.
Required properties:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-dma", where CHIP is the processor
(mpc8349, mpc8360, etc.) and the second is
"fsl,elo-dma"
- reg : <registers mapping for DMA general status reg>
- ranges : Should be defined as specified in 1) to describe the
DMA controller channels.
- cell-index : controller index. 0 for controller @ 0x8100
- interrupts : <interrupt mapping for DMA IRQ>
- interrupt-parent : optional, if needed for interrupt mapping
- DMA channel nodes:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-dma-channel", where CHIP is the processor
(mpc8349, mpc8350, etc.) and the second is
"fsl,elo-dma-channel"
- reg : <registers mapping for channel>
- cell-index : dma channel index starts at 0.
Optional properties:
- interrupts : <interrupt mapping for DMA channel IRQ>
(on 83xx this is expected to be identical to
the interrupts property of the parent node)
- interrupt-parent : optional, if needed for interrupt mapping
Example:
dma@82a8 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
reg = <82a8 4>;
ranges = <0 8100 1a4>;
interrupt-parent = <&ipic>;
interrupts = <47 8>;
cell-index = <0>;
dma-channel@0 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
cell-index = <0>;
reg = <0 80>;
};
dma-channel@80 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
cell-index = <1>;
reg = <80 80>;
};
dma-channel@100 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
cell-index = <2>;
reg = <100 80>;
};
dma-channel@180 {
compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
cell-index = <3>;
reg = <180 80>;
};
};
* Freescale 85xx/86xx DMA Controller
Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers.
Required properties:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-dma", where CHIP is the processor
(mpc8540, mpc8540, etc.) and the second is
"fsl,eloplus-dma"
- reg : <registers mapping for DMA general status reg>
- cell-index : controller index. 0 for controller @ 0x21000,
1 for controller @ 0xc000
- ranges : Should be defined as specified in 1) to describe the
DMA controller channels.
- DMA channel nodes:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-dma-channel", where CHIP is the processor
(mpc8540, mpc8560, etc.) and the second is
"fsl,eloplus-dma-channel"
- cell-index : dma channel index starts at 0.
- reg : <registers mapping for channel>
- interrupts : <interrupt mapping for DMA channel IRQ>
- interrupt-parent : optional, if needed for interrupt mapping
Example:
dma@21300 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
reg = <21300 4>;
ranges = <0 21100 200>;
cell-index = <0>;
dma-channel@0 {
compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
reg = <0 80>;
cell-index = <0>;
interrupt-parent = <&mpic>;
interrupts = <14 2>;
};
dma-channel@80 {
compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
reg = <80 80>;
cell-index = <1>;
interrupt-parent = <&mpic>;
interrupts = <15 2>;
};
dma-channel@100 {
compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
reg = <100 80>;
cell-index = <2>;
interrupt-parent = <&mpic>;
interrupts = <16 2>;
};
dma-channel@180 {
compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
reg = <180 80>;
cell-index = <3>;
interrupt-parent = <&mpic>;
interrupts = <17 2>;
};
};
Documentation/powerpc/dts-bindings/fsl/gtm.txt 0 → 100644
View file @ d0fc2eaa
* Freescale General-purpose Timers Module
Required properties:
- compatible : should be
"fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
"fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
"fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
- reg : should contain gtm registers location and length (0x40).
- interrupts : should contain four interrupts.
- interrupt-parent : interrupt source phandle.
- clock-frequency : specifies the frequency driving the timer.
Example:
timer@500 {
compatible = "fsl,mpc8360-gtm", "fsl,gtm";
reg = <0x500 0x40>;
interrupts = <90 8 78 8 84 8 72 8>;
interrupt-parent = <&ipic>;
/* filled by u-boot */
clock-frequency = <0>;
};
timer@440 {
compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
reg = <0x440 0x40>;
interrupts = <12 13 14 15>;
interrupt-parent = <&qeic>;
/* filled by u-boot */
clock-frequency = <0>;
};
Documentation/powerpc/dts-bindings/fsl/guts.txt 0 → 100644
View file @ d0fc2eaa
* Global Utilities Block
The global utilities block controls power management, I/O device
enabling, power-on-reset configuration monitoring, general-purpose
I/O signal configuration, alternate function selection for multiplexed
signals, and clock control.
Required properties:
- compatible : Should define the compatible device type for
global-utilities.
- reg : Offset and length of the register set for the device.
Recommended properties:
- fsl,has-rstcr : Indicates that the global utilities register set
contains a functioning "reset control register" (i.e. the board
is wired to reset upon setting the HRESET_REQ bit in this register).
Example:
global-utilities@e0000 { /* global utilities block */
compatible = "fsl,mpc8548-guts";
reg = <e0000 1000>;
fsl,has-rstcr;
};
Documentation/powerpc/dts-bindings/fsl/i2c.txt 0 → 100644
View file @ d0fc2eaa
* I2C
Required properties :
- device_type : Should be "i2c"
- reg : Offset and length of the register set for the device
Recommended properties :
- compatible : Should be "fsl-i2c" for parts compatible with
Freescale I2C specifications.
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- dfsrr : boolean; if defined, indicates that this I2C device has
a digital filter sampling rate register
- fsl5200-clocking : boolean; if defined, indicated that this device
uses the FSL 5200 clocking mechanism.
Example :
i2c@3000 {
interrupt-parent = <40000>;
interrupts = <1b 3>;
reg = <3000 18>;
device_type = "i2c";
compatible = "fsl-i2c";
dfsrr;
};
Documentation/powerpc/dts-bindings/fsl/lbc.txt 0 → 100644
View file @ d0fc2eaa
* Chipselect/Local Bus
Properties:
- name : Should be localbus
- #address-cells : Should be either two or three. The first cell is the
chipselect number, and the remaining cells are the
offset into the chipselect.
- #size-cells : Either one or two, depending on how large each chipselect
can be.
- ranges : Each range corresponds to a single chipselect, and cover
the entire access window as configured.
Example:
localbus@f0010100 {
compatible = "fsl,mpc8272-localbus",
"fsl,pq2-localbus";
#address-cells = <2>;
#size-cells = <1>;
reg = <f0010100 40>;
ranges = <0 0 fe000000 02000000
1 0 f4500000 00008000>;
flash@0,0 {
compatible = "jedec-flash";
reg = <0 0 2000000>;
bank-width = <4>;
device-width = <1>;
};
board-control@1,0 {
reg = <1 0 20>;
compatible = "fsl,mpc8272ads-bcsr";
};
};
Documentation/powerpc/dts-bindings/fsl/msi-pic.txt 0 → 100644
View file @ d0fc2eaa
* Freescale MSI interrupt controller
Reguired properities:
- compatible : compatible list, contains 2 entries,
first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572,
etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on
the parent type.
- reg : should contain the address and the length of the shared message
interrupt register set.
- msi-available-ranges: use <start count> style section to define which
msi interrupt can be used in the 256 msi interrupts. This property is
optional, without this, all the 256 MSI interrupts can be used.
- interrupts : each one of the interrupts here is one entry per 32 MSIs,
and routed to the host interrupt controller. the interrupts should
be set as edge sensitive.
- interrupt-parent: the phandle for the interrupt controller
that services interrupts for this device. for 83xx cpu, the interrupts
are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed
to MPIC.
Example:
msi@41600 {
compatible = "fsl,mpc8610-msi", "fsl,mpic-msi";
reg = <0x41600 0x80>;
msi-available-ranges = <0 0x100>;
interrupts = <
0xe0 0
0xe1 0
0xe2 0
0xe3 0
0xe4 0
0xe5 0
0xe6 0
0xe7 0>;
interrupt-parent = <&mpic>;
};
Documentation/powerpc/dts-bindings/fsl/sata.txt 0 → 100644
View file @ d0fc2eaa
* Freescale 8xxx/3.0 Gb/s SATA nodes
SATA nodes are defined to describe on-chip Serial ATA controllers.
Each SATA port should have its own node.
Required properties:
- compatible : compatible list, contains 2 entries, first is
"fsl,CHIP-sata", where CHIP is the processor
(mpc8315, mpc8379, etc.) and the second is
"fsl,pq-sata"
- interrupts : <interrupt mapping for SATA IRQ>
- cell-index : controller index.
1 for controller @ 0x18000
2 for controller @ 0x19000
3 for controller @ 0x1a000
4 for controller @ 0x1b000
Optional properties:
- interrupt-parent : optional, if needed for interrupt mapping
- reg : <registers mapping>
Example:
sata@18000 {
compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
reg = <0x18000 0x1000>;
cell-index = <1>;
interrupts = <2c 8>;
interrupt-parent = < &ipic >;
};
Documentation/powerpc/dts-bindings/fsl/spi.txt 0 → 100644
View file @ d0fc2eaa
* SPI (Serial Peripheral Interface)
Required properties:
- cell-index : SPI controller index.
- compatible : should be "fsl,spi".
- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
- reg : Offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
Example:
spi@4c0 {
cell-index = <0>;
compatible = "fsl,spi";
reg = <4c0 40>;
interrupts = <82 0>;
interrupt-parent = <700>;
mode = "cpu";
};
Documentation/powerpc/dts-bindings/fsl/ssi.txt 0 → 100644
View file @ d0fc2eaa
Freescale Synchronous Serial Interface
The SSI is a serial device that communicates with audio codecs. It can
be programmed in AC97, I2S, left-justified, or right-justified modes.
Required properties:
- compatible : compatible list, containing "fsl,ssi"
- cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on
- reg : offset and length of the register set for the device
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and
level information for the interrupt. This should be
encoded based on the information in section 2)
depending on the type of interrupt controller you
have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- fsl,mode : the operating mode for the SSI interface
"i2s-slave" - I2S mode, SSI is clock slave
"i2s-master" - I2S mode, SSI is clock master
"lj-slave" - left-justified mode, SSI is clock slave
"lj-master" - l.j. mode, SSI is clock master
"rj-slave" - right-justified mode, SSI is clock slave
"rj-master" - r.j., SSI is clock master
"ac97-slave" - AC97 mode, SSI is clock slave
"ac97-master" - AC97 mode, SSI is clock master
Optional properties:
- codec-handle : phandle to a 'codec' node that defines an audio
codec connected to this SSI. This node is typically
a child of an I2C or other control node.
Child 'codec' node required properties:
- compatible : compatible list, contains the name of the codec
Child 'codec' node optional properties:
- clock-frequency : The frequency of the input clock, which typically
comes from an on-board dedicated oscillator.
Documentation/powerpc/dts-bindings/fsl/tsec.txt 0 → 100644
View file @ d0fc2eaa
* MDIO IO device
The MDIO is a bus to which the PHY devices are connected. For each
device that exists on this bus, a child node should be created. See
the definition of the PHY node below for an example of how to define
a PHY.
Required properties:
- reg : Offset and length of the register set for the device
- compatible : Should define the compatible device type for the
mdio. Currently, this is most likely to be "fsl,gianfar-mdio"
Example:
mdio@24520 {
reg = <24520 20>;
compatible = "fsl,gianfar-mdio";
ethernet-phy@0 {
......
};
};
* Gianfar-compatible ethernet nodes
Required properties:
- device_type : Should be "network"
- model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
- compatible : Should be "gianfar"
- reg : Offset and length of the register set for the device
- mac-address : List of bytes representing the ethernet address of
this controller
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
- phy-handle : The phandle for the PHY connected to this ethernet
controller.
- fixed-link : <a b c d e> where a is emulated phy id - choose any,
but unique to the all specified fixed-links, b is duplex - 0 half,
1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
Recommended properties:
- phy-connection-type : a string naming the controller/PHY interface type,
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
"tbi", or "rtbi". This property is only really needed if the connection
is of type "rgmii-id", as all other connection types are detected by
hardware.
Example:
ethernet@24000 {
#size-cells = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <24000 1000>;
mac-address = [ 00 E0 0C 00 73 00 ];
interrupts = <d 3 e 3 12 3>;
interrupt-parent = <40000>;
phy-handle = <2452000>
};
Documentation/powerpc/dts-bindings/fsl/usb.txt 0 → 100644
View file @ d0fc2eaa
Freescale SOC USB controllers
The device node for a USB controller that is part of a Freescale
SOC is as described in the document "Open Firmware Recommended
Practice : Universal Serial Bus" with the following modifications
and additions :
Required properties :
- compatible : Should be "fsl-usb2-mph" for multi port host USB
controllers, or "fsl-usb2-dr" for dual role USB controllers
- phy_type : For multi port host USB controllers, should be one of
"ulpi", or "serial". For dual role USB controllers, should be
one of "ulpi", "utmi", "utmi_wide", or "serial".
- reg : Offset and length of the register set for the device
- port0 : boolean; if defined, indicates port0 is connected for
fsl-usb2-mph compatible controllers. Either this property or
"port1" (or both) must be defined for "fsl-usb2-mph" compatible
controllers.
- port1 : boolean; if defined, indicates port1 is connected for
fsl-usb2-mph compatible controllers. Either this property or
"port0" (or both) must be defined for "fsl-usb2-mph" compatible
controllers.
- dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
controllers. Can be "host", "peripheral", or "otg". Default to
"host" if not defined for backward compatibility.
Recommended properties :
- interrupts : <a b> where a is the interrupt number and b is a
field that represents an encoding of the sense and level
information for the interrupt. This should be encoded based on
the information in section 2) depending on the type of interrupt
controller you have.
- interrupt-parent : the phandle for the interrupt controller that
services interrupts for this device.
Example multi port host USB controller device node :
usb@22000 {
compatible = "fsl-usb2-mph";
reg = <22000 1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <700>;
interrupts = <27 1>;
phy_type = "ulpi";
port0;
port1;
};
Example dual role USB controller device node :
usb@23000 {
compatible = "fsl-usb2-dr";
reg = <23000 1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <700>;
interrupts = <26 1>;
dr_mode = "otg";
phy = "ulpi";
};
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7