ARM: omap2: remove unused omap2_pm_init

The omap2420_init_late() and omap2430_init_late() functions
are never called. Removing them also shows that the entire
arch/arm/mach-omap2/pm24xx.c file is unused and can be
removed.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/mach-omap2/Makefile

@@ -80,7 +80,6 @@ obj-$(CONFIG_ARCH_OMAP4)		+= $(omap-4-5-pm-common)
 obj-$(CONFIG_SOC_OMAP5)			+= $(omap-4-5-pm-common)
 
 ifeq ($(CONFIG_PM),y)
-obj-$(CONFIG_ARCH_OMAP2)		+= pm24xx.o
 obj-$(CONFIG_ARCH_OMAP2)		+= sleep24xx.o
 obj-$(CONFIG_ARCH_OMAP3)		+= pm34xx.o sleep34xx.o
 omap-4-5-pm-common			+= pm44xx.o

arch/arm/mach-omap2/common.h

@@ -44,15 +44,6 @@
 extern int (*omap_pm_soc_init)(void);
 int omap_pm_nop_init(void);
 
-#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP2)
-int omap2_pm_init(void);
-#else
-static inline int omap2_pm_init(void)
-{
-	return 0;
-}
-#endif
-
 #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
 int omap3_pm_init(void);
 #else

arch/arm/mach-omap2/io.c

@@ -435,11 +435,6 @@ void __init omap2420_init_early(void)
 	omap_clk_soc_init = omap2420_dt_clk_init;
 	rate_table = omap2420_rate_table;
 }
-
-void __init omap2420_init_late(void)
-{
-	omap_pm_soc_init = omap2_pm_init;
-}
 #endif
 
 #ifdef CONFIG_SOC_OMAP2430
@@ -459,11 +454,6 @@ void __init omap2430_init_early(void)
 	omap_clk_soc_init = omap2430_dt_clk_init;
 	rate_table = omap2430_rate_table;
 }
-
-void __init omap2430_init_late(void)
-{
-	omap_pm_soc_init = omap2_pm_init;
-}
 #endif
 
 /*

arch/arm/mach-omap2/pm24xx.c

-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * OMAP2 Power Management Routines
- *
- * Copyright (C) 2005 Texas Instruments, Inc.
- * Copyright (C) 2006-2008 Nokia Corporation
- *
- * Written by:
- * Richard Woodruff <r-woodruff2@ti.com>
- * Tony Lindgren
- * Juha Yrjola
- * Amit Kucheria <amit.kucheria@nokia.com>
- * Igor Stoppa <igor.stoppa@nokia.com>
- *
- * Based on pm.c for omap1
- */
-
-#include <linux/cpu_pm.h>
-#include <linux/suspend.h>
-#include <linux/sched.h>
-#include <linux/proc_fs.h>
-#include <linux/interrupt.h>
-#include <linux/sysfs.h>
-#include <linux/module.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/clk-provider.h>
-#include <linux/irq.h>
-#include <linux/time.h>
-
-#include <asm/fncpy.h>
-
-#include <asm/mach/time.h>
-#include <asm/mach/irq.h>
-#include <asm/mach-types.h>
-#include <asm/system_misc.h>
-
-#include <linux/omap-dma.h>
-
-#include "soc.h"
-#include "common.h"
-#include "clock.h"
-#include "prm2xxx.h"
-#include "prm-regbits-24xx.h"
-#include "cm2xxx.h"
-#include "cm-regbits-24xx.h"
-#include "sdrc.h"
-#include "sram.h"
-#include "pm.h"
-#include "control.h"
-#include "powerdomain.h"
-#include "clockdomain.h"
-
-static void (*omap2_sram_suspend)(u32 dllctrl, void __iomem *sdrc_dlla_ctrl,
-				  void __iomem *sdrc_power);
-
-static struct powerdomain *mpu_pwrdm, *core_pwrdm;
-static struct clockdomain *dsp_clkdm, *mpu_clkdm, *wkup_clkdm, *gfx_clkdm;
-
-static struct clk *osc_ck, *emul_ck;
-
-static int omap2_enter_full_retention(void)
-{
-	u32 l;
-
-	/* There is 1 reference hold for all children of the oscillator
-	 * clock, the following will remove it. If no one else uses the
-	 * oscillator itself it will be disabled if/when we enter retention
-	 * mode.
-	 */
-	clk_disable(osc_ck);
-
-	/* Clear old wake-up events */
-	/* REVISIT: These write to reserved bits? */
-	omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
-	omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);
-	omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, ~0);
-
-	pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
-	pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
-
-	/* Workaround to kill USB */
-	l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
-	omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
-
-	/* One last check for pending IRQs to avoid extra latency due
-	 * to sleeping unnecessarily. */
-	if (omap_irq_pending())
-		goto no_sleep;
-
-	/* Jump to SRAM suspend code */
-	omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
-			   OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
-			   OMAP_SDRC_REGADDR(SDRC_POWER));
-
-no_sleep:
-	clk_enable(osc_ck);
-
-	/* clear CORE wake-up events */
-	omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
-	omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);
-
-	/* wakeup domain events - bit 1: GPT1, bit5 GPIO */
-	omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, 0x4 | 0x1);
-
-	/* MPU domain wake events */
-	omap_prm_clear_mod_irqs(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET, 0x1);
-
-	omap_prm_clear_mod_irqs(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET, 0x20);
-
-	pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
-	pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_ON);
-
-	return 0;
-}
-
-static int sti_console_enabled;
-
-static int omap2_allow_mpu_retention(void)
-{
-	if (!omap2xxx_cm_mpu_retention_allowed())
-		return 0;
-	if (sti_console_enabled)
-		return 0;
-
-	return 1;
-}
-
-static void omap2_enter_mpu_retention(void)
-{
-	const int zero = 0;
-
-	/* The peripherals seem not to be able to wake up the MPU when
-	 * it is in retention mode. */
-	if (omap2_allow_mpu_retention()) {
-		/* REVISIT: These write to reserved bits? */
-		omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
-		omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);
-		omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, ~0);
-
-		/* Try to enter MPU retention */
-		pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
-
-	} else {
-		/* Block MPU retention */
-		pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
-	}
-
-	/* WFI */
-	asm("mcr p15, 0, %0, c7, c0, 4" : : "r" (zero) : "memory", "cc");
-
-	pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
-}
-
-static int omap2_can_sleep(void)
-{
-	if (omap2xxx_cm_fclks_active())
-		return 0;
-	if (__clk_is_enabled(osc_ck))
-		return 0;
-
-	return 1;
-}
-
-static void omap2_pm_idle(void)
-{
-	int error;
-
-	if (omap_irq_pending())
-		return;
-
-	error = cpu_cluster_pm_enter();
-	if (error || !omap2_can_sleep()) {
-		omap2_enter_mpu_retention();
-		goto out_cpu_cluster_pm;
-	}
-
-	omap2_enter_full_retention();
-
-out_cpu_cluster_pm:
-	cpu_cluster_pm_exit();
-}
-
-static void __init prcm_setup_regs(void)
-{
-	int i, num_mem_banks;
-	struct powerdomain *pwrdm;
-
-	/*
-	 * Enable autoidle
-	 * XXX This should be handled by hwmod code or PRCM init code
-	 */
-	omap2_prm_write_mod_reg(OMAP24XX_AUTOIDLE_MASK, OCP_MOD,
-			  OMAP2_PRCM_SYSCONFIG_OFFSET);
-
-	/*
-	 * Set CORE powerdomain memory banks to retain their contents
-	 * during RETENTION
-	 */
-	num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
-	for (i = 0; i < num_mem_banks; i++)
-		pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
-
-	pwrdm_set_logic_retst(core_pwrdm, PWRDM_POWER_RET);
-
-	pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
-
-	/* Force-power down DSP, GFX powerdomains */
-
-	pwrdm = clkdm_get_pwrdm(dsp_clkdm);
-	pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
-
-	pwrdm = clkdm_get_pwrdm(gfx_clkdm);
-	pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
-
-	/* Enable hardware-supervised idle for all clkdms */
-	clkdm_for_each(omap_pm_clkdms_setup, NULL);
-	clkdm_add_wkdep(mpu_clkdm, wkup_clkdm);
-
-	omap_common_suspend_init(omap2_enter_full_retention);
-
-	/* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
-	 * stabilisation */
-	omap2_prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
-				OMAP2_PRCM_CLKSSETUP_OFFSET);
-
-	/* Configure automatic voltage transition */
-	omap2_prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
-				OMAP2_PRCM_VOLTSETUP_OFFSET);
-	omap2_prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT_MASK |
-				(0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
-				OMAP24XX_MEMRETCTRL_MASK |
-				(0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
-				(0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
-				OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
-
-	/* Enable wake-up events */
-	omap2_prm_write_mod_reg(OMAP24XX_EN_GPIOS_MASK | OMAP24XX_EN_GPT1_MASK,
-				WKUP_MOD, PM_WKEN);
-
-	/* Enable SYS_CLKEN control when all domains idle */
-	omap2_prm_set_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK, OMAP24XX_GR_MOD,
-				   OMAP2_PRCM_CLKSRC_CTRL_OFFSET);
-}
-
-int __init omap2_pm_init(void)
-{
-	u32 l;
-
-	printk(KERN_INFO "Power Management for OMAP2 initializing\n");
-	l = omap2_prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_REVISION_OFFSET);
-	printk(KERN_INFO "PRCM revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);
-
-	/* Look up important powerdomains */
-
-	mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
-	if (!mpu_pwrdm)
-		pr_err("PM: mpu_pwrdm not found\n");
-
-	core_pwrdm = pwrdm_lookup("core_pwrdm");
-	if (!core_pwrdm)
-		pr_err("PM: core_pwrdm not found\n");
-
-	/* Look up important clockdomains */
-
-	mpu_clkdm = clkdm_lookup("mpu_clkdm");
-	if (!mpu_clkdm)
-		pr_err("PM: mpu_clkdm not found\n");
-
-	wkup_clkdm = clkdm_lookup("wkup_clkdm");
-	if (!wkup_clkdm)
-		pr_err("PM: wkup_clkdm not found\n");
-
-	dsp_clkdm = clkdm_lookup("dsp_clkdm");
-	if (!dsp_clkdm)
-		pr_err("PM: dsp_clkdm not found\n");
-
-	gfx_clkdm = clkdm_lookup("gfx_clkdm");
-	if (!gfx_clkdm)
-		pr_err("PM: gfx_clkdm not found\n");
-
-
-	osc_ck = clk_get(NULL, "osc_ck");
-	if (IS_ERR(osc_ck)) {
-		printk(KERN_ERR "could not get osc_ck\n");
-		return -ENODEV;
-	}
-
-	if (cpu_is_omap242x()) {
-		emul_ck = clk_get(NULL, "emul_ck");
-		if (IS_ERR(emul_ck)) {
-			printk(KERN_ERR "could not get emul_ck\n");
-			clk_put(osc_ck);
-			return -ENODEV;
-		}
-	}
-
-	prcm_setup_regs();
-
-	/*
-	 * We copy the assembler sleep/wakeup routines to SRAM.
-	 * These routines need to be in SRAM as that's the only
-	 * memory the MPU can see when it wakes up after the entire
-	 * chip enters idle.
-	 */
-	omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
-					    omap24xx_cpu_suspend_sz);
-
-	arm_pm_idle = omap2_pm_idle;
-
-	return 0;
-}