Merge branch 'cxgb4-improve-and-tune-TC-MQPRIO-offload'

Rahul Lakkireddy says:

====================
cxgb4: improve and tune TC-MQPRIO offload

Patch 1 improves the Tx path's credit request and recovery mechanism
when running under heavy load.

Patch 2 adds ability to tune the burst buffer sizes of all traffic
classes to improve performance for <= 1500 MTU, under heavy load.

Patch 3 adds support to track EOTIDs and dump software queue
contexts used by TC-MQPRIO offload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/chelsio/cxgb4/cxgb4.h

@@ -1125,19 +1125,20 @@ struct adapter {
  * programmed with various parameters.
  */
 struct ch_sched_params {
-	s8   type;                     /* packet or flow */
+	u8   type;                     /* packet or flow */
 	union {
 		struct {
-			s8   level;    /* scheduler hierarchy level */
-			s8   mode;     /* per-class or per-flow */
-			s8   rateunit; /* bit or packet rate */
-			s8   ratemode; /* %port relative or kbps absolute */
-			s8   channel;  /* scheduler channel [0..N] */
-			s8   class;    /* scheduler class [0..N] */
-			s32  minrate;  /* minimum rate */
-			s32  maxrate;  /* maximum rate */
-			s16  weight;   /* percent weight */
-			s16  pktsize;  /* average packet size */
+			u8   level;    /* scheduler hierarchy level */
+			u8   mode;     /* per-class or per-flow */
+			u8   rateunit; /* bit or packet rate */
+			u8   ratemode; /* %port relative or kbps absolute */
+			u8   channel;  /* scheduler channel [0..N] */
+			u8   class;    /* scheduler class [0..N] */
+			u32  minrate;  /* minimum rate */
+			u32  maxrate;  /* maximum rate */
+			u16  weight;   /* percent weight */
+			u16  pktsize;  /* average packet size */
+			u16  burstsize;  /* burst buffer size */
 		} params;
 	} u;
 };
@@ -1952,9 +1953,10 @@ int t4_sge_ctxt_rd(struct adapter *adap, unsigned int mbox, unsigned int cid,
 		   enum ctxt_type ctype, u32 *data);
 int t4_sge_ctxt_rd_bd(struct adapter *adap, unsigned int cid,
 		      enum ctxt_type ctype, u32 *data);
-int t4_sched_params(struct adapter *adapter, int type, int level, int mode,
-		    int rateunit, int ratemode, int channel, int class,
-		    int minrate, int maxrate, int weight, int pktsize);
+int t4_sched_params(struct adapter *adapter, u8 type, u8 level, u8 mode,
+		    u8 rateunit, u8 ratemode, u8 channel, u8 class,
+		    u32 minrate, u32 maxrate, u16 weight, u16 pktsize,
+		    u16 burstsize);
 void t4_sge_decode_idma_state(struct adapter *adapter, int state);
 void t4_idma_monitor_init(struct adapter *adapter,
 			  struct sge_idma_monitor_state *idma);

drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c

@@ -49,6 +49,7 @@
 #include "cudbg_lib_common.h"
 #include "cudbg_entity.h"
 #include "cudbg_lib.h"
+#include "cxgb4_tc_mqprio.h"
 
 /* generic seq_file support for showing a table of size rows x width. */
 static void *seq_tab_get_idx(struct seq_tab *tb, loff_t pos)
@@ -2657,32 +2658,19 @@ static int sge_qinfo_uld_ciq_entries(const struct adapter *adap, int uld)
 
 static int sge_qinfo_show(struct seq_file *seq, void *v)
 {
-	int eth_entries, ctrl_entries, eo_entries = 0;
+	int eth_entries, ctrl_entries, eohw_entries = 0, eosw_entries = 0;
 	int uld_rxq_entries[CXGB4_ULD_MAX] = { 0 };
 	int uld_ciq_entries[CXGB4_ULD_MAX] = { 0 };
 	int uld_txq_entries[CXGB4_TX_MAX] = { 0 };
 	const struct sge_uld_txq_info *utxq_info;
 	const struct sge_uld_rxq_info *urxq_info;
+	struct cxgb4_tc_port_mqprio *port_mqprio;
 	struct adapter *adap = seq->private;
-	int i, n, r = (uintptr_t)v - 1;
+	int i, j, n, r = (uintptr_t)v - 1;
 	struct sge *s = &adap->sge;
 
 	eth_entries = DIV_ROUND_UP(adap->sge.ethqsets, 4);
 	ctrl_entries = DIV_ROUND_UP(MAX_CTRL_QUEUES, 4);
-	if (adap->sge.eohw_txq)
-		eo_entries = DIV_ROUND_UP(adap->sge.eoqsets, 4);
-
-	mutex_lock(&uld_mutex);
-	if (s->uld_txq_info)
-		for (i = 0; i < ARRAY_SIZE(uld_txq_entries); i++)
-			uld_txq_entries[i] = sge_qinfo_uld_txq_entries(adap, i);
-
-	if (s->uld_rxq_info) {
-		for (i = 0; i < ARRAY_SIZE(uld_rxq_entries); i++) {
-			uld_rxq_entries[i] = sge_qinfo_uld_rxq_entries(adap, i);
-			uld_ciq_entries[i] = sge_qinfo_uld_ciq_entries(adap, i);
-		}
-	}
 
 	if (r)
 		seq_putc(seq, '\n');
@@ -2759,11 +2747,21 @@ do { \
 		RL("FLLow:", fl.low);
 		RL("FLStarving:", fl.starving);
 
-		goto unlock;
+		goto out;
 	}
 
 	r -= eth_entries;
-	if (r < eo_entries) {
+	if (!adap->tc_mqprio)
+		goto skip_mqprio;
+
+	mutex_lock(&adap->tc_mqprio->mqprio_mutex);
+	if (!refcount_read(&adap->tc_mqprio->refcnt)) {
+		mutex_unlock(&adap->tc_mqprio->mqprio_mutex);
+		goto skip_mqprio;
+	}
+
+	eohw_entries = DIV_ROUND_UP(adap->sge.eoqsets, 4);
+	if (r < eohw_entries) {
 		int base_qset = r * 4;
 		const struct sge_ofld_rxq *rx = &s->eohw_rxq[base_qset];
 		const struct sge_eohw_txq *tx = &s->eohw_txq[base_qset];
@@ -2808,10 +2806,71 @@ do { \
 		RL("FLLow:", fl.low);
 		RL("FLStarving:", fl.starving);
 
-		goto unlock;
+		mutex_unlock(&adap->tc_mqprio->mqprio_mutex);
+		goto out;
+	}
+
+	r -= eohw_entries;
+	for (j = 0; j < adap->params.nports; j++) {
+		int entries;
+		u8 tc;
+
+		port_mqprio = &adap->tc_mqprio->port_mqprio[j];
+		entries = 0;
+		for (tc = 0; tc < port_mqprio->mqprio.qopt.num_tc; tc++)
+			entries += port_mqprio->mqprio.qopt.count[tc];
+
+		if (!entries)
+			continue;
+
+		eosw_entries = DIV_ROUND_UP(entries, 4);
+		if (r < eosw_entries) {
+			const struct sge_eosw_txq *tx;
+
+			n = min(4, entries - 4 * r);
+			tx = &port_mqprio->eosw_txq[4 * r];
+
+			S("QType:", "EOSW-TXQ");
+			S("Interface:",
+			  adap->port[j] ? adap->port[j]->name : "N/A");
+			T("EOTID:", hwtid);
+			T("HWQID:", hwqid);
+			T("State:", state);
+			T("Size:", ndesc);
+			T("In-Use:", inuse);
+			T("Credits:", cred);
+			T("Compl:", ncompl);
+			T("Last-Compl:", last_compl);
+			T("PIDX:", pidx);
+			T("Last-PIDX:", last_pidx);
+			T("CIDX:", cidx);
+			T("Last-CIDX:", last_cidx);
+			T("FLOWC-IDX:", flowc_idx);
+
+			mutex_unlock(&adap->tc_mqprio->mqprio_mutex);
+			goto out;
+		}
+
+		r -= eosw_entries;
+	}
+	mutex_unlock(&adap->tc_mqprio->mqprio_mutex);
+
+skip_mqprio:
+	if (!is_uld(adap))
+		goto skip_uld;
+
+	mutex_lock(&uld_mutex);
+	if (s->uld_txq_info)
+		for (i = 0; i < ARRAY_SIZE(uld_txq_entries); i++)
+			uld_txq_entries[i] = sge_qinfo_uld_txq_entries(adap, i);
+
+	if (s->uld_rxq_info) {
+		for (i = 0; i < ARRAY_SIZE(uld_rxq_entries); i++) {
+			uld_rxq_entries[i] = sge_qinfo_uld_rxq_entries(adap, i);
+			uld_ciq_entries[i] = sge_qinfo_uld_ciq_entries(adap, i);
+		}
 	}
 
-	r -= eo_entries;
 	if (r < uld_txq_entries[CXGB4_TX_OFLD]) {
 		const struct sge_uld_txq *tx;
 
@@ -2994,6 +3053,9 @@ do { \
 	}
 
 	r -= uld_txq_entries[CXGB4_TX_CRYPTO];
+	mutex_unlock(&uld_mutex);
+
+skip_uld:
 	if (r < ctrl_entries) {
 		const struct sge_ctrl_txq *tx = &s->ctrlq[r * 4];
 
@@ -3008,7 +3070,7 @@ do { \
 		TL("TxQFull:", q.stops);
 		TL("TxQRestarts:", q.restarts);
 
-		goto unlock;
+		goto out;
 	}
 
 	r -= ctrl_entries;
@@ -3026,11 +3088,9 @@ do { \
 		seq_printf(seq, "%-12s %16u\n", "Intr pktcnt:",
 			   s->counter_val[evtq->pktcnt_idx]);
 
-		goto unlock;
+		goto out;
 	}
 
-unlock:
-	mutex_unlock(&uld_mutex);
 #undef R
 #undef RL
 #undef T
@@ -3039,13 +3099,38 @@ do { \
 #undef R3
 #undef T3
 #undef S3
+out:
+	return 0;
+
+unlock:
+	mutex_unlock(&uld_mutex);
 	return 0;
 }
 
 static int sge_queue_entries(const struct adapter *adap)
 {
-	int tot_uld_entries = 0;
-	int i;
+	int i, tot_uld_entries = 0, eohw_entries = 0, eosw_entries = 0;
+
+	if (adap->tc_mqprio) {
+		struct cxgb4_tc_port_mqprio *port_mqprio;
+		u8 tc;
+
+		mutex_lock(&adap->tc_mqprio->mqprio_mutex);
+		if (adap->sge.eohw_txq)
+			eohw_entries = DIV_ROUND_UP(adap->sge.eoqsets, 4);
+
+		for (i = 0; i < adap->params.nports; i++) {
+			u32 entries = 0;
+
+			port_mqprio = &adap->tc_mqprio->port_mqprio[i];
+			for (tc = 0; tc < port_mqprio->mqprio.qopt.num_tc; tc++)
+				entries += port_mqprio->mqprio.qopt.count[tc];
+
+			if (entries)
+				eosw_entries += DIV_ROUND_UP(entries, 4);
+		}
+		mutex_unlock(&adap->tc_mqprio->mqprio_mutex);
+	}
 
 	if (!is_uld(adap))
 		goto lld_only;
@@ -3062,8 +3147,7 @@ static int sge_queue_entries(const struct adapter *adap)
 
 lld_only:
 	return DIV_ROUND_UP(adap->sge.ethqsets, 4) +
-	       (adap->sge.eohw_txq ? DIV_ROUND_UP(adap->sge.eoqsets, 4) : 0) +
-	       tot_uld_entries +
+	       eohw_entries + eosw_entries + tot_uld_entries +
 	       DIV_ROUND_UP(MAX_CTRL_QUEUES, 4) + 1;
 }
 
@@ -3244,6 +3328,10 @@ static int tid_info_show(struct seq_file *seq, void *v)
 	if (t->nhpftids)
 		seq_printf(seq, "HPFTID range: %u..%u\n", t->hpftid_base,
 			   t->hpftid_base + t->nhpftids - 1);
+	if (t->neotids)
+		seq_printf(seq, "EOTID range: %u..%u, in use: %u\n",
+			   t->eotid_base, t->eotid_base + t->neotids - 1,
+			   atomic_read(&t->eotids_in_use));
 	if (t->ntids)
 		seq_printf(seq, "HW TID usage: %u IP users, %u IPv6 users\n",
 			   t4_read_reg(adap, LE_DB_ACT_CNT_IPV4_A),

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c

@@ -1579,6 +1579,7 @@ static int tid_init(struct tid_info *t)
 	atomic_set(&t->tids_in_use, 0);
 	atomic_set(&t->conns_in_use, 0);
 	atomic_set(&t->hash_tids_in_use, 0);
+	atomic_set(&t->eotids_in_use, 0);
 
 	/* Setup the free list for atid_tab and clear the stid bitmap. */
 	if (natids) {
@@ -3021,7 +3022,7 @@ static int cxgb4_mgmt_set_vf_rate(struct net_device *dev, int vf,
 			      SCHED_CLASS_RATEUNIT_BITS,
 			      SCHED_CLASS_RATEMODE_ABS,
 			      pi->tx_chan, class_id, 0,
-			      max_tx_rate * 1000, 0, pktsize);
+			      max_tx_rate * 1000, 0, pktsize, 0);
 	if (ret) {
 		dev_err(adap->pdev_dev, "Err %d for Traffic Class config\n",
 			ret);

drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_mqprio.c

@@ -342,6 +342,13 @@ static int cxgb4_mqprio_alloc_tc(struct net_device *dev,
 		p.u.params.minrate = div_u64(mqprio->min_rate[i] * 8, 1000);
 		p.u.params.maxrate = div_u64(mqprio->max_rate[i] * 8, 1000);
 
+		/* Request larger burst buffer for smaller MTU, so
+		 * that hardware can work on more data per burst
+		 * cycle.
+		 */
+		if (dev->mtu <= ETH_DATA_LEN)
+			p.u.params.burstsize = 8 * dev->mtu;
+
 		e = cxgb4_sched_class_alloc(dev, &p);
 		if (!e) {
 			ret = -ENOMEM;
@@ -567,6 +574,7 @@ static void cxgb4_mqprio_disable_offload(struct net_device *dev)
 int cxgb4_setup_tc_mqprio(struct net_device *dev,
 			  struct tc_mqprio_qopt_offload *mqprio)
 {
+	struct adapter *adap = netdev2adap(dev);
 	bool needs_bring_up = false;
 	int ret;
 
@@ -574,6 +582,8 @@ int cxgb4_setup_tc_mqprio(struct net_device *dev,
 	if (ret)
 		return ret;
 
+	mutex_lock(&adap->tc_mqprio->mqprio_mutex);
+
 	/* To configure tc params, the current allocated EOTIDs must
 	 * be freed up. However, they can't be freed up if there's
 	 * traffic running on the interface. So, ensure interface is
@@ -609,6 +619,7 @@ int cxgb4_setup_tc_mqprio(struct net_device *dev,
 	if (needs_bring_up)
 		cxgb_open(dev);
 
+	mutex_unlock(&adap->tc_mqprio->mqprio_mutex);
 	return ret;
 }
 
@@ -621,6 +632,7 @@ void cxgb4_mqprio_stop_offload(struct adapter *adap)
 	if (!adap->tc_mqprio || !adap->tc_mqprio->port_mqprio)
 		return;
 
+	mutex_lock(&adap->tc_mqprio->mqprio_mutex);
 	for_each_port(adap, i) {
 		dev = adap->port[i];
 		if (!dev)
@@ -632,6 +644,7 @@ void cxgb4_mqprio_stop_offload(struct adapter *adap)
 
 		cxgb4_mqprio_disable_offload(dev);
 	}
+	mutex_unlock(&adap->tc_mqprio->mqprio_mutex);
 }
 
 int cxgb4_init_tc_mqprio(struct adapter *adap)
@@ -653,6 +666,8 @@ int cxgb4_init_tc_mqprio(struct adapter *adap)
 		goto out_free_mqprio;
 	}
 
+	mutex_init(&tc_mqprio->mqprio_mutex);
+
 	tc_mqprio->port_mqprio = tc_port_mqprio;
 	for (i = 0; i < adap->params.nports; i++) {
 		port_mqprio = &tc_mqprio->port_mqprio[i];
@@ -687,6 +702,7 @@ void cxgb4_cleanup_tc_mqprio(struct adapter *adap)
 	u8 i;
 
 	if (adap->tc_mqprio) {
+		mutex_lock(&adap->tc_mqprio->mqprio_mutex);
 		if (adap->tc_mqprio->port_mqprio) {
 			for (i = 0; i < adap->params.nports; i++) {
 				struct net_device *dev = adap->port[i];
@@ -698,6 +714,7 @@ void cxgb4_cleanup_tc_mqprio(struct adapter *adap)
 			}
 			kfree(adap->tc_mqprio->port_mqprio);
 		}
+		mutex_unlock(&adap->tc_mqprio->mqprio_mutex);
 		kfree(adap->tc_mqprio);
 	}
 }

drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_mqprio.h

@@ -33,6 +33,7 @@ struct cxgb4_tc_port_mqprio {
 
 struct cxgb4_tc_mqprio {
 	refcount_t refcnt; /* Refcount for adapter-wide resources */
+	struct mutex mqprio_mutex; /* Lock for accessing MQPRIO info */
 	struct cxgb4_tc_port_mqprio *port_mqprio; /* Per port MQPRIO info */
 };
 

drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.h

@@ -147,6 +147,9 @@ struct tid_info {
 	/* TIDs in the HASH */
 	atomic_t hash_tids_in_use;
 	atomic_t conns_in_use;
+	/* ETHOFLD TIDs used for rate limiting */
+	atomic_t eotids_in_use;
+
 	/* lock for setting/clearing filter bitmap */
 	spinlock_t ftid_lock;
 
@@ -221,12 +224,14 @@ static inline void cxgb4_alloc_eotid(struct tid_info *t, u32 eotid, void *data)
 {
 	set_bit(eotid, t->eotid_bmap);
 	t->eotid_tab[eotid].data = data;
+	atomic_inc(&t->eotids_in_use);
 }
 
 static inline void cxgb4_free_eotid(struct tid_info *t, u32 eotid)
 {
 	clear_bit(eotid, t->eotid_bmap);
 	t->eotid_tab[eotid].data = NULL;
+	atomic_dec(&t->eotids_in_use);
 }
 
 int cxgb4_alloc_atid(struct tid_info *t, void *data);

drivers/net/ethernet/chelsio/cxgb4/sched.c

@@ -57,7 +57,8 @@ static int t4_sched_class_fw_cmd(struct port_info *pi,
 				      p->u.params.ratemode,
 				      p->u.params.channel, e->idx,
 				      p->u.params.minrate, p->u.params.maxrate,
-				      p->u.params.weight, p->u.params.pktsize);
+				      p->u.params.weight, p->u.params.pktsize,
+				      p->u.params.burstsize);
 		break;
 	default:
 		err = -ENOTSUPP;

drivers/net/ethernet/chelsio/cxgb4/sge.c

@@ -2091,8 +2091,7 @@ static inline u8 ethofld_calc_tx_flits(struct adapter *adap,
 	return flits + nsgl;
 }
 
-static inline void *write_eo_wr(struct adapter *adap,
-				struct sge_eosw_txq *eosw_txq,
+static void *write_eo_wr(struct adapter *adap, struct sge_eosw_txq *eosw_txq,
 			 struct sk_buff *skb, struct fw_eth_tx_eo_wr *wr,
 			 u32 hdr_len, u32 wrlen)
 {
@@ -2113,7 +2112,8 @@ static inline void *write_eo_wr(struct adapter *adap,
 	immd_len += hdr_len;
 
 	if (!eosw_txq->ncompl ||
-	    eosw_txq->last_compl >= adap->params.ofldq_wr_cred / 2) {
+	    (eosw_txq->last_compl + wrlen16) >=
+	    (adap->params.ofldq_wr_cred / 2)) {
 		compl = true;
 		eosw_txq->ncompl++;
 		eosw_txq->last_compl = 0;
@@ -2153,7 +2153,7 @@ static inline void *write_eo_wr(struct adapter *adap,
 	return cpl;
 }
 
-static void ethofld_hard_xmit(struct net_device *dev,
+static int ethofld_hard_xmit(struct net_device *dev,
 			     struct sge_eosw_txq *eosw_txq)
 {
 	struct port_info *pi = netdev2pinfo(dev);
@@ -2167,8 +2167,8 @@ static void ethofld_hard_xmit(struct net_device *dev,
 	bool skip_eotx_wr = false;
 	struct tx_sw_desc *d;
 	struct sk_buff *skb;
+	int left, ret = 0;
 	u8 flits, ndesc;
-	int left;
 
 	eohw_txq = &adap->sge.eohw_txq[eosw_txq->hwqid];
 	spin_lock(&eohw_txq->lock);
@@ -2198,11 +2198,19 @@ static void ethofld_hard_xmit(struct net_device *dev,
 	wrlen = flits * 8;
 	wrlen16 = DIV_ROUND_UP(wrlen, 16);
 
-	/* If there are no CPL credits, then wait for credits
-	 * to come back and retry again
+	left = txq_avail(&eohw_txq->q) - ndesc;
+
+	/* If there are no descriptors left in hardware queues or no
+	 * CPL credits left in software queues, then wait for them
+	 * to come back and retry again. Note that we always request
+	 * for credits update via interrupt for every half credits
+	 * consumed. So, the interrupt will eventually restore the
+	 * credits and invoke the Tx path again.
 	 */
-	if (unlikely(wrlen16 > eosw_txq->cred))
+	if (unlikely(left < 0 || wrlen16 > eosw_txq->cred)) {
+		ret = -ENOMEM;
 		goto out_unlock;
+	}
 
 	if (unlikely(skip_eotx_wr)) {
 		start = (u64 *)wr;
@@ -2231,7 +2239,8 @@ static void ethofld_hard_xmit(struct net_device *dev,
 	sgl = (u64 *)inline_tx_skb_header(skb, &eohw_txq->q, (void *)start,
 					  hdr_len);
 	if (data_len) {
-		if (unlikely(cxgb4_map_skb(adap->pdev_dev, skb, d->addr))) {
+		ret = cxgb4_map_skb(adap->pdev_dev, skb, d->addr);
+		if (unlikely(ret)) {
 			memset(d->addr, 0, sizeof(d->addr));
 			eohw_txq->mapping_err++;
 			goto out_unlock;
@@ -2277,12 +2286,13 @@ static void ethofld_hard_xmit(struct net_device *dev,
 
 out_unlock:
 	spin_unlock(&eohw_txq->lock);
+	return ret;
 }
 
 static void ethofld_xmit(struct net_device *dev, struct sge_eosw_txq *eosw_txq)
 {
 	struct sk_buff *skb;
-	int pktcount;
+	int pktcount, ret;
 
 	switch (eosw_txq->state) {
 	case CXGB4_EO_STATE_ACTIVE:
@@ -2307,7 +2317,9 @@ static void ethofld_xmit(struct net_device *dev, struct sge_eosw_txq *eosw_txq)
 			continue;
 		}
 
-		ethofld_hard_xmit(dev, eosw_txq);
+		ret = ethofld_hard_xmit(dev, eosw_txq);
+		if (ret)
+			break;
 	}
 }
 

drivers/net/ethernet/chelsio/cxgb4/t4_hw.c

@@ -10361,9 +10361,10 @@ int t4_sge_ctxt_rd_bd(struct adapter *adap, unsigned int cid,
 	return ret;
 }
 
-int t4_sched_params(struct adapter *adapter, int type, int level, int mode,
-		    int rateunit, int ratemode, int channel, int class,
-		    int minrate, int maxrate, int weight, int pktsize)
+int t4_sched_params(struct adapter *adapter, u8 type, u8 level, u8 mode,
+		    u8 rateunit, u8 ratemode, u8 channel, u8 class,
+		    u32 minrate, u32 maxrate, u16 weight, u16 pktsize,
+		    u16 burstsize)
 {
 	struct fw_sched_cmd cmd;
 
@@ -10385,6 +10386,7 @@ int t4_sched_params(struct adapter *adapter, int type, int level, int mode,
 	cmd.u.params.max = cpu_to_be32(maxrate);
 	cmd.u.params.weight = cpu_to_be16(weight);
 	cmd.u.params.pktsize = cpu_to_be16(pktsize);
+	cmd.u.params.burstsize = cpu_to_be16(burstsize);
 
 	return t4_wr_mbox_meat(adapter, adapter->mbox, &cmd, sizeof(cmd),
 			       NULL, 1);