Commit d4fc858f authored by Russell King's avatar Russell King Committed by Russell King

[ARM] pxa: program MFPs for low power mode when suspending

Hook the MFP code into the power management code so that the MFPs can
be reconfigured when suspending and resuming.  However, note the FIXME
- low power mode MFP configuration may depend on the system state being
entered.

Also note that we have to clear any detected edge events prior to
entering a low power mode - otherwise we immediately wake up.
Signed-off-by: default avatarRussell King <rmk+kernel@arm.linux.org.uk>
parent 7f7c8a61
...@@ -17,6 +17,7 @@ ...@@ -17,6 +17,7 @@
#include <linux/kernel.h> #include <linux/kernel.h>
#include <linux/init.h> #include <linux/init.h>
#include <linux/io.h> #include <linux/io.h>
#include <linux/sysdev.h>
#include <asm/hardware.h> #include <asm/hardware.h>
#include <asm/arch/mfp.h> #include <asm/arch/mfp.h>
...@@ -87,8 +88,13 @@ static inline void __mfp_config_run(struct pxa3xx_mfp_pin *p) ...@@ -87,8 +88,13 @@ static inline void __mfp_config_run(struct pxa3xx_mfp_pin *p)
static inline void __mfp_config_lpm(struct pxa3xx_mfp_pin *p) static inline void __mfp_config_lpm(struct pxa3xx_mfp_pin *p)
{ {
if (mfp_configured(p) && p->mfpr_lpm != p->mfpr_run) if (mfp_configured(p)) {
mfpr_writel(p->mfpr_off, p->mfpr_lpm); unsigned long mfpr_clr = (p->mfpr_run & ~MFPR_EDGE_BOTH) | MFPR_EDGE_CLEAR;
if (mfpr_clr != p->mfpr_run)
mfpr_writel(p->mfpr_off, mfpr_clr);
if (p->mfpr_lpm != mfpr_clr)
mfpr_writel(p->mfpr_off, p->mfpr_lpm);
}
} }
void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num) void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num)
...@@ -189,3 +195,52 @@ void __init pxa3xx_init_mfp(void) ...@@ -189,3 +195,52 @@ void __init pxa3xx_init_mfp(void)
for (i = 0; i < ARRAY_SIZE(mfp_table); i++) for (i = 0; i < ARRAY_SIZE(mfp_table); i++)
mfp_table[i].config = -1; mfp_table[i].config = -1;
} }
#ifdef CONFIG_PM
/*
* Configure the MFPs appropriately for suspend/resume.
* FIXME: this should probably depend on which system state we're
* entering - for instance, we might not want to place MFP pins in
* a pull-down mode if they're an active low chip select, and we're
* just entering standby.
*/
static int pxa3xx_mfp_suspend(struct sys_device *d, pm_message_t state)
{
int pin;
for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++) {
struct pxa3xx_mfp_pin *p = &mfp_table[pin];
__mfp_config_lpm(p);
}
return 0;
}
static int pxa3xx_mfp_resume(struct sys_device *d)
{
int pin;
for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++) {
struct pxa3xx_mfp_pin *p = &mfp_table[pin];
__mfp_config_run(p);
}
return 0;
}
static struct sysdev_class mfp_sysclass = {
set_kset_name("mfp"),
.suspend = pxa3xx_mfp_suspend,
.resume = pxa3xx_mfp_resume,
};
static struct sys_device mfp_device = {
.id = 0,
.cls = &mfp_sysclass,
};
static int __init mfp_init_devicefs(void)
{
sysdev_class_register(&mfp_sysclass);
return sysdev_register(&mfp_device);
}
device_initcall(mfp_init_devicefs);
#endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment