Merge branch 'x86/apic-cleanups' into x86/numa

Documentation/x86/boot.txt

@@ -600,6 +600,7 @@ Protocol:	2.07+
   0x00000001	lguest
   0x00000002	Xen
   0x00000003	Moorestown MID
+  0x00000004	CE4100 TV Platform
 
 Field name:	hardware_subarch_data
 Type:		write (subarch-dependent)

arch/x86/Kconfig

@@ -377,6 +377,18 @@ config X86_ELAN
 
 	  If unsure, choose "PC-compatible" instead.
 
+config X86_INTEL_CE
+	bool "CE4100 TV platform"
+	depends on PCI
+	depends on PCI_GODIRECT
+	depends on X86_32
+	depends on X86_EXTENDED_PLATFORM
+	select X86_REBOOTFIXUPS
+	---help---
+	  Select for the Intel CE media processor (CE4100) SOC.
+	  This option compiles in support for the CE4100 SOC for settop
+	  boxes and media devices.
+
 config X86_MRST
        bool "Moorestown MID platform"
 	depends on PCI
@@ -385,6 +397,10 @@ config X86_MRST
 	depends on X86_EXTENDED_PLATFORM
 	depends on X86_IO_APIC
 	select APB_TIMER
+	select I2C
+	select SPI
+	select INTEL_SCU_IPC
+	select X86_PLATFORM_DEVICES
 	---help---
 	  Moorestown is Intel's Low Power Intel Architecture (LPIA) based Moblin
 	  Internet Device(MID) platform. Moorestown consists of two chips:
@@ -466,6 +482,19 @@ config X86_ES7000
 	  Support for Unisys ES7000 systems.  Say 'Y' here if this kernel is
 	  supposed to run on an IA32-based Unisys ES7000 system.
 
+config X86_32_IRIS
+	tristate "Eurobraille/Iris poweroff module"
+	depends on X86_32
+	---help---
+	  The Iris machines from EuroBraille do not have APM or ACPI support
+	  to shut themselves down properly.  A special I/O sequence is
+	  needed to do so, which is what this module does at
+	  kernel shutdown.
+
+	  This is only for Iris machines from EuroBraille.
+
+	  If unused, say N.
+
 config SCHED_OMIT_FRAME_POINTER
 	def_bool y
 	prompt "Single-depth WCHAN output"

arch/x86/include/asm/apic.h

@@ -234,16 +234,17 @@ extern void init_bsp_APIC(void);
 extern void setup_local_APIC(void);
 extern void end_local_APIC_setup(void);
 extern void init_apic_mappings(void);
+void register_lapic_address(unsigned long address);
 extern void setup_boot_APIC_clock(void);
 extern void setup_secondary_APIC_clock(void);
 extern int APIC_init_uniprocessor(void);
 extern void enable_NMI_through_LVT0(void);
+extern int apic_force_enable(void);
 
 /*
  * On 32bit this is mach-xxx local
  */
 #ifdef CONFIG_X86_64
-extern void early_init_lapic_mapping(void);
 extern int apic_is_clustered_box(void);
 #else
 static inline int apic_is_clustered_box(void)

arch/x86/include/asm/bootparam.h

@@ -124,6 +124,7 @@ enum {
 	X86_SUBARCH_LGUEST,
 	X86_SUBARCH_XEN,
 	X86_SUBARCH_MRST,
+	X86_SUBARCH_CE4100,
 	X86_NR_SUBARCHS,
 };
 

arch/x86/include/asm/fixmap.h

@@ -117,6 +117,10 @@ enum fixed_addresses {
 	FIX_TEXT_POKE1,	/* reserve 2 pages for text_poke() */
 	FIX_TEXT_POKE0, /* first page is last, because allocation is backward */
 	__end_of_permanent_fixed_addresses,
+
+#ifdef	CONFIG_X86_MRST
+	FIX_LNW_VRTC,
+#endif
 	/*
 	 * 256 temporary boot-time mappings, used by early_ioremap(),
 	 * before ioremap() is functional.

arch/x86/include/asm/io_apic.h

@@ -159,7 +159,7 @@ struct io_apic_irq_attr;
 extern int io_apic_set_pci_routing(struct device *dev, int irq,
 		 struct io_apic_irq_attr *irq_attr);
 void setup_IO_APIC_irq_extra(u32 gsi);
-extern void ioapic_init_mappings(void);
+extern void ioapic_and_gsi_init(void);
 extern void ioapic_insert_resources(void);
 
 extern struct IO_APIC_route_entry **alloc_ioapic_entries(void);
@@ -168,10 +168,10 @@ extern int save_IO_APIC_setup(struct IO_APIC_route_entry **ioapic_entries);
 extern void mask_IO_APIC_setup(struct IO_APIC_route_entry **ioapic_entries);
 extern int restore_IO_APIC_setup(struct IO_APIC_route_entry **ioapic_entries);
 
-extern void probe_nr_irqs_gsi(void);
 extern int get_nr_irqs_gsi(void);
 
 extern void setup_ioapic_ids_from_mpc(void);
+extern void setup_ioapic_ids_from_mpc_nocheck(void);
 
 struct mp_ioapic_gsi{
 	u32 gsi_base;
@@ -184,14 +184,15 @@ int mp_find_ioapic_pin(int ioapic, u32 gsi);
 void __init mp_register_ioapic(int id, u32 address, u32 gsi_base);
 extern void __init pre_init_apic_IRQ0(void);
 
+extern void mp_save_irq(struct mpc_intsrc *m);
+
 #else  /* !CONFIG_X86_IO_APIC */
 
 #define io_apic_assign_pci_irqs 0
 #define setup_ioapic_ids_from_mpc x86_init_noop
 static const int timer_through_8259 = 0;
-static inline void ioapic_init_mappings(void)	{ }
+static inline void ioapic_and_gsi_init(void) { }
 static inline void ioapic_insert_resources(void) { }
-static inline void probe_nr_irqs_gsi(void)	{ }
 #define gsi_top (NR_IRQS_LEGACY)
 static inline int mp_find_ioapic(u32 gsi) { return 0; }
 

arch/x86/include/asm/mrst-vrtc.h

+#ifndef _MRST_VRTC_H
+#define _MRST_VRTC_H
+
+extern unsigned char vrtc_cmos_read(unsigned char reg);
+extern void vrtc_cmos_write(unsigned char val, unsigned char reg);
+extern unsigned long vrtc_get_time(void);
+extern int vrtc_set_mmss(unsigned long nowtime);
+
+#endif

arch/x86/include/asm/mrst.h

@@ -14,7 +14,9 @@
 #include <linux/sfi.h>
 
 extern int pci_mrst_init(void);
-int __init sfi_parse_mrtc(struct sfi_table_header *table);
+extern int __init sfi_parse_mrtc(struct sfi_table_header *table);
+extern int sfi_mrtc_num;
+extern struct sfi_rtc_table_entry sfi_mrtc_array[];
 
 /*
  * Medfield is the follow-up of Moorestown, it combines two chip solution into
@@ -50,4 +52,14 @@ extern void mrst_early_console_init(void);
 
 extern struct console early_hsu_console;
 extern void hsu_early_console_init(void);
+
+extern void intel_scu_devices_create(void);
+extern void intel_scu_devices_destroy(void);
+
+/* VRTC timer */
+#define MRST_VRTC_MAP_SZ	(1024)
+/*#define MRST_VRTC_PGOFFSET	(0xc00) */
+
+extern void mrst_rtc_init(void);
+
 #endif /* _ASM_X86_MRST_H */

arch/x86/include/asm/setup.h

@@ -53,6 +53,12 @@ extern void x86_mrst_early_setup(void);
 static inline void x86_mrst_early_setup(void) { }
 #endif
 
+#ifdef CONFIG_X86_INTEL_CE
+extern void x86_ce4100_early_setup(void);
+#else
+static inline void x86_ce4100_early_setup(void) { }
+#endif
+
 #ifndef _SETUP
 
 /*

arch/x86/kernel/Makefile

@@ -84,7 +84,6 @@ obj-$(CONFIG_DOUBLEFAULT) 	+= doublefault_32.o
 obj-$(CONFIG_KGDB)		+= kgdb.o
 obj-$(CONFIG_VM86)		+= vm86_32.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
-obj-$(CONFIG_EARLY_PRINTK_MRST)	+= early_printk_mrst.o
 
 obj-$(CONFIG_HPET_TIMER) 	+= hpet.o
 obj-$(CONFIG_APB_TIMER)		+= apb_timer.o

arch/x86/kernel/acpi/boot.c

@@ -847,18 +847,6 @@ static int __init acpi_parse_fadt(struct acpi_table_header *table)
  * returns 0 on success, < 0 on error
  */
 
-static void __init acpi_register_lapic_address(unsigned long address)
-{
-	mp_lapic_addr = address;
-
-	set_fixmap_nocache(FIX_APIC_BASE, address);
-	if (boot_cpu_physical_apicid == -1U) {
-		boot_cpu_physical_apicid  = read_apic_id();
-		apic_version[boot_cpu_physical_apicid] =
-			 GET_APIC_VERSION(apic_read(APIC_LVR));
-	}
-}
-
 static int __init early_acpi_parse_madt_lapic_addr_ovr(void)
 {
 	int count;
@@ -880,7 +868,7 @@ static int __init early_acpi_parse_madt_lapic_addr_ovr(void)
 		return count;
 	}
 
-	acpi_register_lapic_address(acpi_lapic_addr);
+	register_lapic_address(acpi_lapic_addr);
 
 	return count;
 }
@@ -907,7 +895,7 @@ static int __init acpi_parse_madt_lapic_entries(void)
 		return count;
 	}
 
-	acpi_register_lapic_address(acpi_lapic_addr);
+	register_lapic_address(acpi_lapic_addr);
 
 	count = acpi_table_parse_madt(ACPI_MADT_TYPE_LOCAL_SAPIC,
 				      acpi_parse_sapic, MAX_APICS);
@@ -949,32 +937,6 @@ static int __init acpi_parse_madt_lapic_entries(void)
 extern int es7000_plat;
 #endif
 
-static void assign_to_mp_irq(struct mpc_intsrc *m,
-				    struct mpc_intsrc *mp_irq)
-{
-	memcpy(mp_irq, m, sizeof(struct mpc_intsrc));
-}
-
-static int mp_irq_cmp(struct mpc_intsrc *mp_irq,
-				struct mpc_intsrc *m)
-{
-	return memcmp(mp_irq, m, sizeof(struct mpc_intsrc));
-}
-
-static void save_mp_irq(struct mpc_intsrc *m)
-{
-	int i;
-
-	for (i = 0; i < mp_irq_entries; i++) {
-		if (!mp_irq_cmp(&mp_irqs[i], m))
-			return;
-	}
-
-	assign_to_mp_irq(m, &mp_irqs[mp_irq_entries]);
-	if (++mp_irq_entries == MAX_IRQ_SOURCES)
-		panic("Max # of irq sources exceeded!!\n");
-}
-
 void __init mp_override_legacy_irq(u8 bus_irq, u8 polarity, u8 trigger, u32 gsi)
 {
 	int ioapic;
@@ -1005,7 +967,7 @@ void __init mp_override_legacy_irq(u8 bus_irq, u8 polarity, u8 trigger, u32 gsi)
 	mp_irq.dstapic = mp_ioapics[ioapic].apicid; /* APIC ID */
 	mp_irq.dstirq = pin;	/* INTIN# */
 
-	save_mp_irq(&mp_irq);
+	mp_save_irq(&mp_irq);
 
 	isa_irq_to_gsi[bus_irq] = gsi;
 }
@@ -1080,7 +1042,7 @@ void __init mp_config_acpi_legacy_irqs(void)
 		mp_irq.srcbusirq = i; /* Identity mapped */
 		mp_irq.dstirq = pin;
 
-		save_mp_irq(&mp_irq);
+		mp_save_irq(&mp_irq);
 	}
 }
 
@@ -1117,7 +1079,7 @@ static int mp_config_acpi_gsi(struct device *dev, u32 gsi, int trigger,
 	mp_irq.dstapic = mp_ioapics[ioapic].apicid;
 	mp_irq.dstirq = mp_find_ioapic_pin(ioapic, gsi);
 
-	save_mp_irq(&mp_irq);
+	mp_save_irq(&mp_irq);
 #endif
 	return 0;
 }

arch/x86/kernel/apb_timer.c

@@ -315,6 +315,7 @@ static void apbt_setup_irq(struct apbt_dev *adev)
 
 	if (system_state == SYSTEM_BOOTING) {
 		irq_modify_status(adev->irq, 0, IRQ_MOVE_PCNTXT);
+		irq_set_affinity(adev->irq, cpumask_of(adev->cpu));
 		/* APB timer irqs are set up as mp_irqs, timer is edge type */
 		__set_irq_handler(adev->irq, handle_edge_irq, 0, "edge");
 		if (request_irq(adev->irq, apbt_interrupt_handler,

arch/x86/kernel/apic/apic.c

@@ -1195,12 +1195,15 @@ static void __cpuinit lapic_setup_esr(void)
 			oldvalue, value);
 }
 
-
 /**
  * setup_local_APIC - setup the local APIC
+ *
+ * Used to setup local APIC while initializing BSP or bringin up APs.
+ * Always called with preemption disabled.
  */
 void __cpuinit setup_local_APIC(void)
 {
+	int cpu = smp_processor_id();
 	unsigned int value, queued;
 	int i, j, acked = 0;
 	unsigned long long tsc = 0, ntsc;
@@ -1225,8 +1228,6 @@ void __cpuinit setup_local_APIC(void)
 #endif
 	perf_events_lapic_init();
 
-	preempt_disable();
-
 	/*
 	 * Double-check whether this APIC is really registered.
 	 * This is meaningless in clustered apic mode, so we skip it.
@@ -1342,21 +1343,19 @@ void __cpuinit setup_local_APIC(void)
 	 * TODO: set up through-local-APIC from through-I/O-APIC? --macro
 	 */
 	value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
-	if (!smp_processor_id() && (pic_mode || !value)) {
+	if (!cpu && (pic_mode || !value)) {
 		value = APIC_DM_EXTINT;
-		apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n",
-				smp_processor_id());
+		apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n", cpu);
 	} else {
 		value = APIC_DM_EXTINT | APIC_LVT_MASKED;
-		apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n",
-				smp_processor_id());
+		apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n", cpu);
 	}
 	apic_write(APIC_LVT0, value);
 
 	/*
 	 * only the BP should see the LINT1 NMI signal, obviously.
 	 */
-	if (!smp_processor_id())
+	if (!cpu)
 		value = APIC_DM_NMI;
 	else
 		value = APIC_DM_NMI | APIC_LVT_MASKED;
@@ -1364,11 +1363,9 @@ void __cpuinit setup_local_APIC(void)
 		value |= APIC_LVT_LEVEL_TRIGGER;
 	apic_write(APIC_LVT1, value);
 
-	preempt_enable();
-
 #ifdef CONFIG_X86_MCE_INTEL
 	/* Recheck CMCI information after local APIC is up on CPU #0 */
-	if (smp_processor_id() == 0)
+	if (!cpu)
 		cmci_recheck();
 #endif
 }
@@ -1530,13 +1527,60 @@ static int __init detect_init_APIC(void)
 	return 0;
 }
 #else
+
+static int apic_verify(void)
+{
+	u32 features, h, l;
+
+	/*
+	 * The APIC feature bit should now be enabled
+	 * in `cpuid'
+	 */
+	features = cpuid_edx(1);
+	if (!(features & (1 << X86_FEATURE_APIC))) {
+		pr_warning("Could not enable APIC!\n");
+		return -1;
+	}
+	set_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
+	mp_lapic_addr = APIC_DEFAULT_PHYS_BASE;
+
+	/* The BIOS may have set up the APIC at some other address */
+	rdmsr(MSR_IA32_APICBASE, l, h);
+	if (l & MSR_IA32_APICBASE_ENABLE)
+		mp_lapic_addr = l & MSR_IA32_APICBASE_BASE;
+
+	pr_info("Found and enabled local APIC!\n");
+	return 0;
+}
+
+int apic_force_enable(void)
+{
+	u32 h, l;
+
+	if (disable_apic)
+		return -1;
+
+	/*
+	 * Some BIOSes disable the local APIC in the APIC_BASE
+	 * MSR. This can only be done in software for Intel P6 or later
+	 * and AMD K7 (Model > 1) or later.
+	 */
+	rdmsr(MSR_IA32_APICBASE, l, h);
+	if (!(l & MSR_IA32_APICBASE_ENABLE)) {
+		pr_info("Local APIC disabled by BIOS -- reenabling.\n");
+		l &= ~MSR_IA32_APICBASE_BASE;
+		l |= MSR_IA32_APICBASE_ENABLE | APIC_DEFAULT_PHYS_BASE;
+		wrmsr(MSR_IA32_APICBASE, l, h);
+		enabled_via_apicbase = 1;
+	}
+	return apic_verify();
+}
+
 /*
  * Detect and initialize APIC
  */
 static int __init detect_init_APIC(void)
 {
-	u32 h, l, features;
-
 	/* Disabled by kernel option? */
 	if (disable_apic)
 		return -1;
@@ -1566,38 +1610,12 @@ static int __init detect_init_APIC(void)
 				"you can enable it with \"lapic\"\n");
 			return -1;
 		}
-		/*
-		 * Some BIOSes disable the local APIC in the APIC_BASE
-		 * MSR. This can only be done in software for Intel P6 or later
-		 * and AMD K7 (Model > 1) or later.
-		 */
-		rdmsr(MSR_IA32_APICBASE, l, h);
-		if (!(l & MSR_IA32_APICBASE_ENABLE)) {
-			pr_info("Local APIC disabled by BIOS -- reenabling.\n");
-			l &= ~MSR_IA32_APICBASE_BASE;
-			l |= MSR_IA32_APICBASE_ENABLE | APIC_DEFAULT_PHYS_BASE;
-			wrmsr(MSR_IA32_APICBASE, l, h);
-			enabled_via_apicbase = 1;
-		}
-	}
-	/*
-	 * The APIC feature bit should now be enabled
-	 * in `cpuid'
-	 */
-	features = cpuid_edx(1);
-	if (!(features & (1 << X86_FEATURE_APIC))) {
-		pr_warning("Could not enable APIC!\n");
-		return -1;
+		if (apic_force_enable())
+			return -1;
+	} else {
+		if (apic_verify())
+			return -1;
 	}
-	set_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
-	mp_lapic_addr = APIC_DEFAULT_PHYS_BASE;
-
-	/* The BIOS may have set up the APIC at some other address */
-	rdmsr(MSR_IA32_APICBASE, l, h);
-	if (l & MSR_IA32_APICBASE_ENABLE)
-		mp_lapic_addr = l & MSR_IA32_APICBASE_BASE;
-
-	pr_info("Found and enabled local APIC!\n");
 
 	apic_pm_activate();
 
@@ -1609,28 +1627,6 @@ static int __init detect_init_APIC(void)
 }
 #endif
 
-#ifdef CONFIG_X86_64
-void __init early_init_lapic_mapping(void)
-{
-	/*
-	 * If no local APIC can be found then go out
-	 * : it means there is no mpatable and MADT
-	 */
-	if (!smp_found_config)
-		return;
-
-	set_fixmap_nocache(FIX_APIC_BASE, mp_lapic_addr);
-	apic_printk(APIC_VERBOSE, "mapped APIC to %16lx (%16lx)\n",
-		    APIC_BASE, mp_lapic_addr);
-
-	/*
-	 * Fetch the APIC ID of the BSP in case we have a
-	 * default configuration (or the MP table is broken).
-	 */
-	boot_cpu_physical_apicid = read_apic_id();
-}
-#endif
-
 /**
  * init_apic_mappings - initialize APIC mappings
  */
@@ -1656,10 +1652,7 @@ void __init init_apic_mappings(void)
 		 * acpi_register_lapic_address()
 		 */
 		if (!acpi_lapic && !smp_found_config)
-			set_fixmap_nocache(FIX_APIC_BASE, apic_phys);
-
-		apic_printk(APIC_VERBOSE, "mapped APIC to %08lx (%08lx)\n",
-					APIC_BASE, apic_phys);
+			register_lapic_address(apic_phys);
 	}
 
 	/*
@@ -1681,6 +1674,22 @@ void __init init_apic_mappings(void)
 	}
 }
 
+void __init register_lapic_address(unsigned long address)
+{
+	mp_lapic_addr = address;
+
+	if (!x2apic_mode) {
+		set_fixmap_nocache(FIX_APIC_BASE, address);
+		apic_printk(APIC_VERBOSE, "mapped APIC to %16lx (%16lx)\n",
+			    APIC_BASE, mp_lapic_addr);
+	}
+	if (boot_cpu_physical_apicid == -1U) {
+		boot_cpu_physical_apicid  = read_apic_id();
+		apic_version[boot_cpu_physical_apicid] =
+			 GET_APIC_VERSION(apic_read(APIC_LVR));
+	}
+}
+
 /*
  * This initializes the IO-APIC and APIC hardware if this is
  * a UP kernel.

arch/x86/kernel/apic/io_apic.c

@@ -126,6 +126,26 @@ static int __init parse_noapic(char *str)
 }
 early_param("noapic", parse_noapic);
 
+/* Will be called in mpparse/acpi/sfi codes for saving IRQ info */
+void mp_save_irq(struct mpc_intsrc *m)
+{
+	int i;
+
+	apic_printk(APIC_VERBOSE, "Int: type %d, pol %d, trig %d, bus %02x,"
+		" IRQ %02x, APIC ID %x, APIC INT %02x\n",
+		m->irqtype, m->irqflag & 3, (m->irqflag >> 2) & 3, m->srcbus,
+		m->srcbusirq, m->dstapic, m->dstirq);
+
+	for (i = 0; i < mp_irq_entries; i++) {
+		if (!memcmp(&mp_irqs[i], m, sizeof(*m)))
+			return;
+	}
+
+	memcpy(&mp_irqs[mp_irq_entries], m, sizeof(*m));
+	if (++mp_irq_entries == MAX_IRQ_SOURCES)
+		panic("Max # of irq sources exceeded!!\n");
+}
+
 struct irq_pin_list {
 	int apic, pin;
 	struct irq_pin_list *next;
@@ -136,6 +156,7 @@ static struct irq_pin_list *alloc_irq_pin_list(int node)
 	return kzalloc_node(sizeof(struct irq_pin_list), GFP_KERNEL, node);
 }
 
+
 /* irq_cfg is indexed by the sum of all RTEs in all I/O APICs. */
 #ifdef CONFIG_SPARSE_IRQ
 static struct irq_cfg irq_cfgx[NR_IRQS_LEGACY];
@@ -1934,8 +1955,7 @@ void disable_IO_APIC(void)
  *
  * by Matt Domsch <Matt_Domsch@dell.com>  Tue Dec 21 12:25:05 CST 1999
  */
-
-void __init setup_ioapic_ids_from_mpc(void)
+void __init setup_ioapic_ids_from_mpc_nocheck(void)
 {
 	union IO_APIC_reg_00 reg_00;
 	physid_mask_t phys_id_present_map;
@@ -1944,15 +1964,6 @@ void __init setup_ioapic_ids_from_mpc(void)
 	unsigned char old_id;
 	unsigned long flags;
 
-	if (acpi_ioapic)
-		return;
-	/*
-	 * Don't check I/O APIC IDs for xAPIC systems.  They have
-	 * no meaning without the serial APIC bus.
-	 */
-	if (!(boot_cpu_data.x86_vendor == X86_VENDOR_INTEL)
-		|| APIC_XAPIC(apic_version[boot_cpu_physical_apicid]))
-		return;
 	/*
 	 * This is broken; anything with a real cpu count has to
 	 * circumvent this idiocy regardless.
@@ -2006,7 +2017,6 @@ void __init setup_ioapic_ids_from_mpc(void)
 			physids_or(phys_id_present_map, phys_id_present_map, tmp);
 		}
 
-
 		/*
 		 * We need to adjust the IRQ routing table
 		 * if the ID changed.
@@ -2018,9 +2028,12 @@ void __init setup_ioapic_ids_from_mpc(void)
 						= mp_ioapics[apic_id].apicid;
 
 		/*
-		 * Read the right value from the MPC table and
-		 * write it into the ID register.
+		 * Update the ID register according to the right value
+		 * from the MPC table if they are different.
 		 */
+		if (mp_ioapics[apic_id].apicid == reg_00.bits.ID)
+			continue;
+
 		apic_printk(APIC_VERBOSE, KERN_INFO
 			"...changing IO-APIC physical APIC ID to %d ...",
 			mp_ioapics[apic_id].apicid);
@@ -2042,6 +2055,21 @@ void __init setup_ioapic_ids_from_mpc(void)
 			apic_printk(APIC_VERBOSE, " ok.\n");
 	}
 }
+
+void __init setup_ioapic_ids_from_mpc(void)
+{
+
+	if (acpi_ioapic)
+		return;
+	/*
+	 * Don't check I/O APIC IDs for xAPIC systems.  They have
+	 * no meaning without the serial APIC bus.
+	 */
+	if (!(boot_cpu_data.x86_vendor == X86_VENDOR_INTEL)
+		|| APIC_XAPIC(apic_version[boot_cpu_physical_apicid]))
+		return;
+	setup_ioapic_ids_from_mpc_nocheck();
+}
 #endif
 
 int no_timer_check __initdata;
@@ -3639,7 +3667,7 @@ int __init io_apic_get_redir_entries (int ioapic)
 	return reg_01.bits.entries + 1;
 }
 
-void __init probe_nr_irqs_gsi(void)
+static void __init probe_nr_irqs_gsi(void)
 {
 	int nr;
 
@@ -3956,7 +3984,7 @@ static struct resource * __init ioapic_setup_resources(int nr_ioapics)
 	return res;
 }
 
-void __init ioapic_init_mappings(void)
+void __init ioapic_and_gsi_init(void)
 {
 	unsigned long ioapic_phys, idx = FIX_IO_APIC_BASE_0;
 	struct resource *ioapic_res;
@@ -3994,6 +4022,8 @@ void __init ioapic_init_mappings(void)
 		ioapic_res->end = ioapic_phys + IO_APIC_SLOT_SIZE - 1;
 		ioapic_res++;
 	}
+
+	probe_nr_irqs_gsi();
 }
 
 void __init ioapic_insert_resources(void)

arch/x86/kernel/early_printk.c

@@ -240,7 +240,7 @@ static int __init setup_early_printk(char *buf)
 		if (!strncmp(buf, "xen", 3))
 			early_console_register(&xenboot_console, keep);
 #endif
-#ifdef CONFIG_X86_MRST_EARLY_PRINTK
+#ifdef CONFIG_EARLY_PRINTK_MRST
 		if (!strncmp(buf, "mrst", 4)) {
 			mrst_early_console_init();
 			early_console_register(&early_mrst_console, keep);
@@ -250,7 +250,6 @@ static int __init setup_early_printk(char *buf)
 			hsu_early_console_init();
 			early_console_register(&early_hsu_console, keep);
 		}
-
 #endif
 		buf++;
 	}

arch/x86/kernel/head32.c

@@ -61,6 +61,9 @@ void __init i386_start_kernel(void)
 	case X86_SUBARCH_MRST:
 		x86_mrst_early_setup();
 		break;
+	case X86_SUBARCH_CE4100:
+		x86_ce4100_early_setup();
+		break;
 	default:
 		i386_default_early_setup();
 		break;

arch/x86/kernel/mpparse.c

@@ -118,21 +118,8 @@ static void __init MP_bus_info(struct mpc_bus *m)
 
 static void __init MP_ioapic_info(struct mpc_ioapic *m)
 {
-	if (!(m->flags & MPC_APIC_USABLE))
-		return;
-
-	printk(KERN_INFO "I/O APIC #%d Version %d at 0x%X.\n",
-	       m->apicid, m->apicver, m->apicaddr);
-
-	mp_register_ioapic(m->apicid, m->apicaddr, gsi_top);
-}
-
-static void print_MP_intsrc_info(struct mpc_intsrc *m)
-{
-	apic_printk(APIC_VERBOSE, "Int: type %d, pol %d, trig %d, bus %02x,"
-		" IRQ %02x, APIC ID %x, APIC INT %02x\n",
-		m->irqtype, m->irqflag & 3, (m->irqflag >> 2) & 3, m->srcbus,
-		m->srcbusirq, m->dstapic, m->dstirq);
+	if (m->flags & MPC_APIC_USABLE)
+		mp_register_ioapic(m->apicid, m->apicaddr, gsi_top);
 }
 
 static void __init print_mp_irq_info(struct mpc_intsrc *mp_irq)
@@ -144,73 +131,11 @@ static void __init print_mp_irq_info(struct mpc_intsrc *mp_irq)
 		mp_irq->srcbusirq, mp_irq->dstapic, mp_irq->dstirq);
 }
 
-static void __init assign_to_mp_irq(struct mpc_intsrc *m,
-				    struct mpc_intsrc *mp_irq)
-{
-	mp_irq->dstapic = m->dstapic;
-	mp_irq->type = m->type;
-	mp_irq->irqtype = m->irqtype;
-	mp_irq->irqflag = m->irqflag;
-	mp_irq->srcbus = m->srcbus;
-	mp_irq->srcbusirq = m->srcbusirq;
-	mp_irq->dstirq = m->dstirq;
-}
-
-static void __init assign_to_mpc_intsrc(struct mpc_intsrc *mp_irq,
-					struct mpc_intsrc *m)
-{
-	m->dstapic = mp_irq->dstapic;
-	m->type = mp_irq->type;
-	m->irqtype = mp_irq->irqtype;
-	m->irqflag = mp_irq->irqflag;
-	m->srcbus = mp_irq->srcbus;
-	m->srcbusirq = mp_irq->srcbusirq;
-	m->dstirq = mp_irq->dstirq;
-}
-
-static int __init mp_irq_mpc_intsrc_cmp(struct mpc_intsrc *mp_irq,
-					struct mpc_intsrc *m)
-{
-	if (mp_irq->dstapic != m->dstapic)
-		return 1;
-	if (mp_irq->type != m->type)
-		return 2;
-	if (mp_irq->irqtype != m->irqtype)
-		return 3;
-	if (mp_irq->irqflag != m->irqflag)
-		return 4;
-	if (mp_irq->srcbus != m->srcbus)
-		return 5;
-	if (mp_irq->srcbusirq != m->srcbusirq)
-		return 6;
-	if (mp_irq->dstirq != m->dstirq)
-		return 7;
-
-	return 0;
-}
-
-static void __init MP_intsrc_info(struct mpc_intsrc *m)
-{
-	int i;
-
-	print_MP_intsrc_info(m);
-
-	for (i = 0; i < mp_irq_entries; i++) {
-		if (!mp_irq_mpc_intsrc_cmp(&mp_irqs[i], m))
-			return;
-	}
-
-	assign_to_mp_irq(m, &mp_irqs[mp_irq_entries]);
-	if (++mp_irq_entries == MAX_IRQ_SOURCES)
-		panic("Max # of irq sources exceeded!!\n");
-}
 #else /* CONFIG_X86_IO_APIC */
 static inline void __init MP_bus_info(struct mpc_bus *m) {}
 static inline void __init MP_ioapic_info(struct mpc_ioapic *m) {}
-static inline void __init MP_intsrc_info(struct mpc_intsrc *m) {}
 #endif /* CONFIG_X86_IO_APIC */
 
-
 static void __init MP_lintsrc_info(struct mpc_lintsrc *m)
 {
 	apic_printk(APIC_VERBOSE, "Lint: type %d, pol %d, trig %d, bus %02x,"
@@ -222,7 +147,6 @@ static void __init MP_lintsrc_info(struct mpc_lintsrc *m)
 /*
  * Read/parse the MPC
  */
-
 static int __init smp_check_mpc(struct mpc_table *mpc, char *oem, char *str)
 {
 
@@ -275,18 +199,6 @@ static void __init smp_dump_mptable(struct mpc_table *mpc, unsigned char *mpt)
 
 void __init default_smp_read_mpc_oem(struct mpc_table *mpc) { }
 
-static void __init smp_register_lapic_address(unsigned long address)
-{
-	mp_lapic_addr = address;
-
-	set_fixmap_nocache(FIX_APIC_BASE, address);
-	if (boot_cpu_physical_apicid == -1U) {
-		boot_cpu_physical_apicid  = read_apic_id();
-		apic_version[boot_cpu_physical_apicid] =
-			 GET_APIC_VERSION(apic_read(APIC_LVR));
-	}
-}
-
 static int __init smp_read_mpc(struct mpc_table *mpc, unsigned early)
 {
 	char str[16];
@@ -301,17 +213,13 @@ static int __init smp_read_mpc(struct mpc_table *mpc, unsigned early)
 #ifdef CONFIG_X86_32
 	generic_mps_oem_check(mpc, oem, str);
 #endif
-	/* save the local APIC address, it might be non-default */
+	/* Initialize the lapic mapping */
 	if (!acpi_lapic)
-		mp_lapic_addr = mpc->lapic;
+		register_lapic_address(mpc->lapic);
 
 	if (early)
 		return 1;
 
-	/* Initialize the lapic mapping */
-	if (!acpi_lapic)
-		smp_register_lapic_address(mpc->lapic);
-
 	if (mpc->oemptr)
 		x86_init.mpparse.smp_read_mpc_oem(mpc);
 
@@ -337,7 +245,7 @@ static int __init smp_read_mpc(struct mpc_table *mpc, unsigned early)
 			skip_entry(&mpt, &count, sizeof(struct mpc_ioapic));
 			break;
 		case MP_INTSRC:
-			MP_intsrc_info((struct mpc_intsrc *)mpt);
+			mp_save_irq((struct mpc_intsrc *)mpt);
 			skip_entry(&mpt, &count, sizeof(struct mpc_intsrc));
 			break;
 		case MP_LINTSRC:
@@ -429,13 +337,13 @@ static void __init construct_default_ioirq_mptable(int mpc_default_type)
 
 		intsrc.srcbusirq = i;
 		intsrc.dstirq = i ? i : 2;	/* IRQ0 to INTIN2 */
-		MP_intsrc_info(&intsrc);
+		mp_save_irq(&intsrc);
 	}
 
 	intsrc.irqtype = mp_ExtINT;
 	intsrc.srcbusirq = 0;
 	intsrc.dstirq = 0;	/* 8259A to INTIN0 */
-	MP_intsrc_info(&intsrc);
+	mp_save_irq(&intsrc);
 }
 
 
@@ -784,11 +692,11 @@ static void __init check_irq_src(struct mpc_intsrc *m, int *nr_m_spare)
 	int i;
 
 	apic_printk(APIC_VERBOSE, "OLD ");
-	print_MP_intsrc_info(m);
+	print_mp_irq_info(m);
 
 	i = get_MP_intsrc_index(m);
 	if (i > 0) {
-		assign_to_mpc_intsrc(&mp_irqs[i], m);
+		memcpy(m, &mp_irqs[i], sizeof(*m));
 		apic_printk(APIC_VERBOSE, "NEW ");
 		print_mp_irq_info(&mp_irqs[i]);
 		return;
@@ -875,14 +783,14 @@ static int  __init replace_intsrc_all(struct mpc_table *mpc,
 		if (nr_m_spare > 0) {
 			apic_printk(APIC_VERBOSE, "*NEW* found\n");
 			nr_m_spare--;
-			assign_to_mpc_intsrc(&mp_irqs[i], m_spare[nr_m_spare]);
+			memcpy(m_spare[nr_m_spare], &mp_irqs[i], sizeof(mp_irqs[i]));
 			m_spare[nr_m_spare] = NULL;
 		} else {
 			struct mpc_intsrc *m = (struct mpc_intsrc *)mpt;
 			count += sizeof(struct mpc_intsrc);
 			if (check_slot(mpc_new_phys, mpc_new_length, count) < 0)
 				goto out;
-			assign_to_mpc_intsrc(&mp_irqs[i], m);
+			memcpy(m, &mp_irqs[i], sizeof(*m));
 			mpc->length = count;
 			mpt += sizeof(struct mpc_intsrc);
 		}

arch/x86/kernel/reboot_fixups_32.c

@@ -43,17 +43,33 @@ static void rdc321x_reset(struct pci_dev *dev)
 	outb(1, 0x92);
 }
 
+static void ce4100_reset(struct pci_dev *dev)
+{
+	int i;
+
+	for (i = 0; i < 10; i++) {
+		outb(0x2, 0xcf9);
+		udelay(50);
+	}
+}
+
 struct device_fixup {
 	unsigned int vendor;
 	unsigned int device;
 	void (*reboot_fixup)(struct pci_dev *);
 };
 
+/*
+ * PCI ids solely used for fixups_table go here
+ */
+#define PCI_DEVICE_ID_INTEL_CE4100	0x0708
+
 static const struct device_fixup fixups_table[] = {
 { PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY, cs5530a_warm_reset },
 { PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, cs5536_warm_reset },
 { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SC1100_BRIDGE, cs5530a_warm_reset },
 { PCI_VENDOR_ID_RDC, PCI_DEVICE_ID_RDC_R6030, rdc321x_reset },
+{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CE4100, ce4100_reset },
 };
 
 /*

arch/x86/kernel/setup.c

@@ -1035,10 +1035,7 @@ void __init setup_arch(char **cmdline_p)
 #endif
 
 	init_apic_mappings();
-	ioapic_init_mappings();
-
-	/* need to wait for io_apic is mapped */
-	probe_nr_irqs_gsi();
+	ioapic_and_gsi_init();
 
 	kvm_guest_init();
 

arch/x86/mm/amdtopology_64.c

@@ -67,7 +67,6 @@ static __init void early_get_boot_cpu_id(void)
 	if (smp_found_config)
 		early_get_smp_config();
 #endif
-	early_init_lapic_mapping();
 }
 
 int __init amd_numa_init(unsigned long start_pfn, unsigned long end_pfn)

arch/x86/pci/Makefile

@@ -7,6 +7,7 @@ obj-$(CONFIG_PCI_OLPC)		+= olpc.o
 obj-$(CONFIG_PCI_XEN)		+= xen.o
 
 obj-y				+= fixup.o
+obj-$(CONFIG_X86_INTEL_CE)      += ce4100.o
 obj-$(CONFIG_ACPI)		+= acpi.o
 obj-y				+= legacy.o irq.o
 

arch/x86/pci/ce4100.c

+/*
+ *  GPL LICENSE SUMMARY
+ *
+ *  Copyright(c) 2010 Intel Corporation. All rights reserved.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of version 2 of the GNU General Public License as
+ *  published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope that it will be useful, but
+ *  WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ *  General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *  The full GNU General Public License is included in this distribution
+ *  in the file called LICENSE.GPL.
+ *
+ *  Contact Information:
+ *    Intel Corporation
+ *    2200 Mission College Blvd.
+ *    Santa Clara, CA  97052
+ *
+ * This provides access methods for PCI registers that mis-behave on
+ * the CE4100. Each register can be assigned a private init, read and
+ * write routine. The exception to this is the bridge device.  The
+ * bridge device is the only device on bus zero (0) that requires any
+ * fixup so it is a special case ATM
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+
+#include <asm/pci_x86.h>
+
+struct sim_reg {
+	u32 value;
+	u32 mask;
+};
+
+struct sim_dev_reg {
+	int dev_func;
+	int reg;
+	void (*init)(struct sim_dev_reg *reg);
+	void (*read)(struct sim_dev_reg *reg, u32 *value);
+	void (*write)(struct sim_dev_reg *reg, u32 value);
+	struct sim_reg sim_reg;
+};
+
+struct sim_reg_op {
+	void (*init)(struct sim_dev_reg *reg);
+	void (*read)(struct sim_dev_reg *reg, u32 value);
+	void (*write)(struct sim_dev_reg *reg, u32 value);
+};
+
+#define MB (1024 * 1024)
+#define KB (1024)
+#define SIZE_TO_MASK(size) (~(size - 1))
+
+#define DEFINE_REG(device, func, offset, size, init_op, read_op, write_op)\
+{ PCI_DEVFN(device, func), offset, init_op, read_op, write_op,\
+	{0, SIZE_TO_MASK(size)} },
+
+static void reg_init(struct sim_dev_reg *reg)
+{
+	pci_direct_conf1.read(0, 1, reg->dev_func, reg->reg, 4,
+			      &reg->sim_reg.value);
+}
+
+static void reg_read(struct sim_dev_reg *reg, u32 *value)
+{
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&pci_config_lock, flags);
+	*value = reg->sim_reg.value;
+	raw_spin_unlock_irqrestore(&pci_config_lock, flags);
+}
+
+static void reg_write(struct sim_dev_reg *reg, u32 value)
+{
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&pci_config_lock, flags);
+	reg->sim_reg.value = (value & reg->sim_reg.mask) |
+		(reg->sim_reg.value & ~reg->sim_reg.mask);
+	raw_spin_unlock_irqrestore(&pci_config_lock, flags);
+}
+
+static void sata_reg_init(struct sim_dev_reg *reg)
+{
+	pci_direct_conf1.read(0, 1, PCI_DEVFN(14, 0), 0x10, 4,
+			      &reg->sim_reg.value);
+	reg->sim_reg.value += 0x400;
+}
+
+static void ehci_reg_read(struct sim_dev_reg *reg, u32 *value)
+{
+	reg_read(reg, value);
+	if (*value != reg->sim_reg.mask)
+		*value |= 0x100;
+}
+
+void sata_revid_init(struct sim_dev_reg *reg)
+{
+	reg->sim_reg.value = 0x01060100;
+	reg->sim_reg.mask = 0;
+}
+
+static void sata_revid_read(struct sim_dev_reg *reg, u32 *value)
+{
+	reg_read(reg, value);
+}
+
+static struct sim_dev_reg bus1_fixups[] = {
+	DEFINE_REG(2, 0, 0x10, (16*MB), reg_init, reg_read, reg_write)
+	DEFINE_REG(2, 0, 0x14, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(2, 1, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(3, 0, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(4, 0, 0x10, (128*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(4, 1, 0x10, (128*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(6, 0, 0x10, (512*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(6, 1, 0x10, (512*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(6, 2, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(8, 0, 0x10, (1*MB), reg_init, reg_read, reg_write)
+	DEFINE_REG(8, 1, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(8, 2, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(9, 0, 0x10 , (1*MB), reg_init, reg_read, reg_write)
+	DEFINE_REG(9, 0, 0x14, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(10, 0, 0x10, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(10, 0, 0x14, (256*MB), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 0, 0x10, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 0, 0x14, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 1, 0x10, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 2, 0x10, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 2, 0x14, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 2, 0x18, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 3, 0x10, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 3, 0x14, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 4, 0x10, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 5, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 6, 0x10, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(11, 7, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(12, 0, 0x10, (128*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(12, 0, 0x14, (256), reg_init, reg_read, reg_write)
+	DEFINE_REG(12, 1, 0x10, (1024), reg_init, reg_read, reg_write)
+	DEFINE_REG(13, 0, 0x10, (32*KB), reg_init, ehci_reg_read, reg_write)
+	DEFINE_REG(13, 1, 0x10, (32*KB), reg_init, ehci_reg_read, reg_write)
+	DEFINE_REG(14, 0, 0x8,  0, sata_revid_init, sata_revid_read, 0)
+	DEFINE_REG(14, 0, 0x10, 0, reg_init, reg_read, reg_write)
+	DEFINE_REG(14, 0, 0x14, 0, reg_init, reg_read, reg_write)
+	DEFINE_REG(14, 0, 0x18, 0, reg_init, reg_read, reg_write)
+	DEFINE_REG(14, 0, 0x1C, 0, reg_init, reg_read, reg_write)
+	DEFINE_REG(14, 0, 0x20, 0, reg_init, reg_read, reg_write)
+	DEFINE_REG(14, 0, 0x24, (0x200), sata_reg_init, reg_read, reg_write)
+	DEFINE_REG(15, 0, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(15, 0, 0x14, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(16, 0, 0x10, (64*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(16, 0, 0x14, (64*MB), reg_init, reg_read, reg_write)
+	DEFINE_REG(16, 0, 0x18, (64*MB), reg_init, reg_read, reg_write)
+	DEFINE_REG(17, 0, 0x10, (128*KB), reg_init, reg_read, reg_write)
+	DEFINE_REG(18, 0, 0x10, (1*KB), reg_init, reg_read, reg_write)
+};
+
+static void __init init_sim_regs(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(bus1_fixups); i++) {
+		if (bus1_fixups[i].init)
+			bus1_fixups[i].init(&bus1_fixups[i]);
+	}
+}
+
+static inline void extract_bytes(u32 *value, int reg, int len)
+{
+	uint32_t mask;
+
+	*value >>= ((reg & 3) * 8);
+	mask = 0xFFFFFFFF >> ((4 - len) * 8);
+	*value &= mask;
+}
+
+int bridge_read(unsigned int devfn, int reg, int len, u32 *value)
+{
+	u32 av_bridge_base, av_bridge_limit;
+	int retval = 0;
+
+	switch (reg) {
+	/* Make BARs appear to not request any memory. */
+	case PCI_BASE_ADDRESS_0:
+	case PCI_BASE_ADDRESS_0 + 1:
+	case PCI_BASE_ADDRESS_0 + 2:
+	case PCI_BASE_ADDRESS_0 + 3:
+		*value = 0;
+		break;
+
+		/* Since subordinate bus number register is hardwired
+		 * to zero and read only, so do the simulation.
+		 */
+	case PCI_PRIMARY_BUS:
+		if (len == 4)
+			*value = 0x00010100;
+		break;
+
+	case PCI_SUBORDINATE_BUS:
+		*value = 1;
+		break;
+
+	case PCI_MEMORY_BASE:
+	case PCI_MEMORY_LIMIT:
+		/* Get the A/V bridge base address. */
+		pci_direct_conf1.read(0, 0, devfn,
+				PCI_BASE_ADDRESS_0, 4, &av_bridge_base);
+
+		av_bridge_limit = av_bridge_base + (512*MB - 1);
+		av_bridge_limit >>= 16;
+		av_bridge_limit &= 0xFFF0;
+
+		av_bridge_base >>= 16;
+		av_bridge_base &= 0xFFF0;
+
+		if (reg == PCI_MEMORY_LIMIT)
+			*value = av_bridge_limit;
+		else if (len == 2)
+			*value = av_bridge_base;
+		else
+			*value = (av_bridge_limit << 16) | av_bridge_base;
+		break;
+		/* Make prefetchable memory limit smaller than prefetchable
+		 * memory base, so not claim prefetchable memory space.
+		 */
+	case PCI_PREF_MEMORY_BASE:
+		*value = 0xFFF0;
+		break;
+	case PCI_PREF_MEMORY_LIMIT:
+		*value = 0x0;
+		break;
+		/* Make IO limit smaller than IO base, so not claim IO space. */
+	case PCI_IO_BASE:
+		*value = 0xF0;
+		break;
+	case PCI_IO_LIMIT:
+		*value = 0;
+		break;
+	default:
+		retval = 1;
+	}
+	return retval;
+}
+
+static int ce4100_conf_read(unsigned int seg, unsigned int bus,
+			    unsigned int devfn, int reg, int len, u32 *value)
+{
+	int i, retval = 1;
+
+	if (bus == 1) {
+		for (i = 0; i < ARRAY_SIZE(bus1_fixups); i++) {
+			if (bus1_fixups[i].dev_func == devfn &&
+			    bus1_fixups[i].reg == (reg & ~3) &&
+			    bus1_fixups[i].read) {
+				bus1_fixups[i].read(&(bus1_fixups[i]),
+						    value);
+				extract_bytes(value, reg, len);
+				return 0;
+			}
+		}
+	}
+
+	if (bus == 0 && (PCI_DEVFN(1, 0) == devfn) &&
+	    !bridge_read(devfn, reg, len, value))
+		return 0;
+
+	return pci_direct_conf1.read(seg, bus, devfn, reg, len, value);
+}
+
+static int ce4100_conf_write(unsigned int seg, unsigned int bus,
+			     unsigned int devfn, int reg, int len, u32 value)
+{
+	int i;
+
+	if (bus == 1) {
+		for (i = 0; i < ARRAY_SIZE(bus1_fixups); i++) {
+			if (bus1_fixups[i].dev_func == devfn &&
+			    bus1_fixups[i].reg == (reg & ~3) &&
+			    bus1_fixups[i].write) {
+				bus1_fixups[i].write(&(bus1_fixups[i]),
+						     value);
+				return 0;
+			}
+		}
+	}
+
+	/* Discard writes to A/V bridge BAR. */
+	if (bus == 0 && PCI_DEVFN(1, 0) == devfn &&
+	    ((reg & ~3) == PCI_BASE_ADDRESS_0))
+		return 0;
+
+	return pci_direct_conf1.write(seg, bus, devfn, reg, len, value);
+}
+
+struct pci_raw_ops ce4100_pci_conf = {
+	.read =	ce4100_conf_read,
+	.write = ce4100_conf_write,
+};
+
+static int __init ce4100_pci_init(void)
+{
+	init_sim_regs();
+	raw_pci_ops = &ce4100_pci_conf;
+	return 0;
+}
+subsys_initcall(ce4100_pci_init);

arch/x86/platform/Makefile

 # Platform specific code goes here
+obj-y	+= ce4100/
 obj-y	+= efi/
+obj-y	+= iris/
 obj-y	+= mrst/
 obj-y	+= olpc/
 obj-y	+= scx200/

arch/x86/platform/ce4100/Makefile

+obj-$(CONFIG_X86_INTEL_CE)	+= ce4100.o

arch/x86/platform/ce4100/ce4100.c

+/*
+ * Intel CE4100  platform specific setup code
+ *
+ * (C) Copyright 2010 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2
+ * of the License.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/serial_reg.h>
+#include <linux/serial_8250.h>
+
+#include <asm/setup.h>
+#include <asm/io.h>
+
+static int ce4100_i8042_detect(void)
+{
+	return 0;
+}
+
+static void __init sdv_find_smp_config(void)
+{
+}
+
+#ifdef CONFIG_SERIAL_8250
+
+
+static unsigned int mem_serial_in(struct uart_port *p, int offset)
+{
+	offset = offset << p->regshift;
+	return readl(p->membase + offset);
+}
+
+/*
+ * The UART Tx interrupts are not set under some conditions and therefore serial
+ * transmission hangs. This is a silicon issue and has not been root caused. The
+ * workaround for this silicon issue checks UART_LSR_THRE bit and UART_LSR_TEMT
+ * bit of LSR register in interrupt handler to see whether at least one of these
+ * two bits is set, if so then process the transmit request. If this workaround
+ * is not applied, then the serial transmission may hang. This workaround is for
+ * errata number 9 in Errata - B step.
+*/
+
+static unsigned int ce4100_mem_serial_in(struct uart_port *p, int offset)
+{
+	unsigned int ret, ier, lsr;
+
+	if (offset == UART_IIR) {
+		offset = offset << p->regshift;
+		ret = readl(p->membase + offset);
+		if (ret & UART_IIR_NO_INT) {
+			/* see if the TX interrupt should have really set */
+			ier = mem_serial_in(p, UART_IER);
+			/* see if the UART's XMIT interrupt is enabled */
+			if (ier & UART_IER_THRI) {
+				lsr = mem_serial_in(p, UART_LSR);
+				/* now check to see if the UART should be
+				   generating an interrupt (but isn't) */
+				if (lsr & (UART_LSR_THRE | UART_LSR_TEMT))
+					ret &= ~UART_IIR_NO_INT;
+			}
+		}
+	} else
+		ret =  mem_serial_in(p, offset);
+	return ret;
+}
+
+static void ce4100_mem_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = offset << p->regshift;
+	writel(value, p->membase + offset);
+}
+
+static void ce4100_serial_fixup(int port, struct uart_port *up,
+	unsigned short *capabilites)
+{
+#ifdef CONFIG_EARLY_PRINTK
+	/*
+	 * Over ride the legacy port configuration that comes from
+	 * asm/serial.h. Using the ioport driver then switching to the
+	 * PCI memmaped driver hangs the IOAPIC
+	 */
+	if (up->iotype !=  UPIO_MEM32) {
+		up->uartclk  = 14745600;
+		up->mapbase = 0xdffe0200;
+		set_fixmap_nocache(FIX_EARLYCON_MEM_BASE,
+				up->mapbase & PAGE_MASK);
+		up->membase =
+			(void __iomem *)__fix_to_virt(FIX_EARLYCON_MEM_BASE);
+		up->membase += up->mapbase & ~PAGE_MASK;
+		up->iotype   = UPIO_MEM32;
+		up->regshift = 2;
+	}
+#endif
+	up->iobase = 0;
+	up->serial_in = ce4100_mem_serial_in;
+	up->serial_out = ce4100_mem_serial_out;
+
+	*capabilites |= (1 << 12);
+}
+
+static __init void sdv_serial_fixup(void)
+{
+	serial8250_set_isa_configurator(ce4100_serial_fixup);
+}
+
+#else
+static inline void sdv_serial_fixup(void);
+#endif
+
+static void __init sdv_arch_setup(void)
+{
+	sdv_serial_fixup();
+}
+
+/*
+ * CE4100 specific x86_init function overrides and early setup
+ * calls.
+ */
+void __init x86_ce4100_early_setup(void)
+{
+	x86_init.oem.arch_setup = sdv_arch_setup;
+	x86_platform.i8042_detect = ce4100_i8042_detect;
+	x86_init.resources.probe_roms = x86_init_noop;
+	x86_init.mpparse.get_smp_config = x86_init_uint_noop;
+	x86_init.mpparse.find_smp_config = sdv_find_smp_config;
+}

arch/x86/platform/iris/Makefile

+obj-$(CONFIG_X86_32_IRIS)		+= iris.o

arch/x86/platform/iris/iris.c

+/*
+ * Eurobraille/Iris power off support.
+ *
+ * Eurobraille's Iris machine is a PC with no APM or ACPI support.
+ * It is shutdown by a special I/O sequence which this module provides.
+ *
+ *  Copyright (C) Shérab <Sebastien.Hinderer@ens-lyon.org>
+ *
+ * This program is free software ; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation ; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY ; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with the program ; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/moduleparam.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/pm.h>
+#include <asm/io.h>
+
+#define IRIS_GIO_BASE		0x340
+#define IRIS_GIO_INPUT		IRIS_GIO_BASE
+#define IRIS_GIO_OUTPUT		(IRIS_GIO_BASE + 1)
+#define IRIS_GIO_PULSE		0x80 /* First byte to send */
+#define IRIS_GIO_REST		0x00 /* Second byte to send */
+#define IRIS_GIO_NODEV		0xff /* Likely not an Iris */
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Sébastien Hinderer <Sebastien.Hinderer@ens-lyon.org>");
+MODULE_DESCRIPTION("A power_off handler for Iris devices from EuroBraille");
+MODULE_SUPPORTED_DEVICE("Eurobraille/Iris");
+
+static int force;
+
+module_param(force, bool, 0);
+MODULE_PARM_DESC(force, "Set to one to force poweroff handler installation.");
+
+static void (*old_pm_power_off)(void);
+
+static void iris_power_off(void)
+{
+	outb(IRIS_GIO_PULSE, IRIS_GIO_OUTPUT);
+	msleep(850);
+	outb(IRIS_GIO_REST, IRIS_GIO_OUTPUT);
+}
+
+/*
+ * Before installing the power_off handler, try to make sure the OS is
+ * running on an Iris.  Since Iris does not support DMI, this is done
+ * by reading its input port and seeing whether the read value is
+ * meaningful.
+ */
+static int iris_init(void)
+{
+	unsigned char status;
+	if (force != 1) {
+		printk(KERN_ERR "The force parameter has not been set to 1 so the Iris poweroff handler will not be installed.\n");
+		return -ENODEV;
+	}
+	status = inb(IRIS_GIO_INPUT);
+	if (status == IRIS_GIO_NODEV) {
+		printk(KERN_ERR "This machine does not seem to be an Iris. Power_off handler not installed.\n");
+		return -ENODEV;
+	}
+	old_pm_power_off = pm_power_off;
+	pm_power_off = &iris_power_off;
+	printk(KERN_INFO "Iris power_off handler installed.\n");
+
+	return 0;
+}
+
+static void iris_exit(void)
+{
+	pm_power_off = old_pm_power_off;
+	printk(KERN_INFO "Iris power_off handler uninstalled.\n");
+}
+
+module_init(iris_init);
+module_exit(iris_exit);

arch/x86/platform/mrst/Makefile

 obj-$(CONFIG_X86_MRST)		+= mrst.o
+obj-$(CONFIG_X86_MRST)		+= vrtc.o
+obj-$(CONFIG_EARLY_PRINTK_MRST)	+= early_printk_mrst.o

arch/x86/platform/mrst/vrtc.c

+/*
+ * vrtc.c: Driver for virtual RTC device on Intel MID platform
+ *
+ * (C) Copyright 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2
+ * of the License.
+ *
+ * Note:
+ * VRTC is emulated by system controller firmware, the real HW
+ * RTC is located in the PMIC device. SCU FW shadows PMIC RTC
+ * in a memory mapped IO space that is visible to the host IA
+ * processor.
+ *
+ * This driver is based on RTC CMOS driver.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sfi.h>
+#include <linux/platform_device.h>
+
+#include <asm/mrst.h>
+#include <asm/mrst-vrtc.h>
+#include <asm/time.h>
+#include <asm/fixmap.h>
+
+static unsigned char __iomem *vrtc_virt_base;
+
+unsigned char vrtc_cmos_read(unsigned char reg)
+{
+	unsigned char retval;
+
+	/* vRTC's registers range from 0x0 to 0xD */
+	if (reg > 0xd || !vrtc_virt_base)
+		return 0xff;
+
+	lock_cmos_prefix(reg);
+	retval = __raw_readb(vrtc_virt_base + (reg << 2));
+	lock_cmos_suffix(reg);
+	return retval;
+}
+EXPORT_SYMBOL_GPL(vrtc_cmos_read);
+
+void vrtc_cmos_write(unsigned char val, unsigned char reg)
+{
+	if (reg > 0xd || !vrtc_virt_base)
+		return;
+
+	lock_cmos_prefix(reg);
+	__raw_writeb(val, vrtc_virt_base + (reg << 2));
+	lock_cmos_suffix(reg);
+}
+EXPORT_SYMBOL_GPL(vrtc_cmos_write);
+
+unsigned long vrtc_get_time(void)
+{
+	u8 sec, min, hour, mday, mon;
+	u32 year;
+
+	while ((vrtc_cmos_read(RTC_FREQ_SELECT) & RTC_UIP))
+		cpu_relax();
+
+	sec = vrtc_cmos_read(RTC_SECONDS);
+	min = vrtc_cmos_read(RTC_MINUTES);
+	hour = vrtc_cmos_read(RTC_HOURS);
+	mday = vrtc_cmos_read(RTC_DAY_OF_MONTH);
+	mon = vrtc_cmos_read(RTC_MONTH);
+	year = vrtc_cmos_read(RTC_YEAR);
+
+	/* vRTC YEAR reg contains the offset to 1960 */
+	year += 1960;
+
+	printk(KERN_INFO "vRTC: sec: %d min: %d hour: %d day: %d "
+		"mon: %d year: %d\n", sec, min, hour, mday, mon, year);
+
+	return mktime(year, mon, mday, hour, min, sec);
+}
+
+/* Only care about the minutes and seconds */
+int vrtc_set_mmss(unsigned long nowtime)
+{
+	int real_sec, real_min;
+	int vrtc_min;
+
+	vrtc_min = vrtc_cmos_read(RTC_MINUTES);
+
+	real_sec = nowtime % 60;
+	real_min = nowtime / 60;
+	if (((abs(real_min - vrtc_min) + 15)/30) & 1)
+		real_min += 30;
+	real_min %= 60;
+
+	vrtc_cmos_write(real_sec, RTC_SECONDS);
+	vrtc_cmos_write(real_min, RTC_MINUTES);
+	return 0;
+}
+
+void __init mrst_rtc_init(void)
+{
+	unsigned long rtc_paddr;
+	void __iomem *virt_base;
+
+	sfi_table_parse(SFI_SIG_MRTC, NULL, NULL, sfi_parse_mrtc);
+	if (!sfi_mrtc_num)
+		return;
+
+	rtc_paddr = sfi_mrtc_array[0].phys_addr;
+
+	/* vRTC's register address may not be page aligned */
+	set_fixmap_nocache(FIX_LNW_VRTC, rtc_paddr);
+
+	virt_base = (void __iomem *)__fix_to_virt(FIX_LNW_VRTC);
+	virt_base += rtc_paddr & ~PAGE_MASK;
+	vrtc_virt_base = virt_base;
+
+	x86_platform.get_wallclock = vrtc_get_time;
+	x86_platform.set_wallclock = vrtc_set_mmss;
+}
+
+/*
+ * The Moorestown platform has a memory mapped virtual RTC device that emulates
+ * the programming interface of the RTC.
+ */
+
+static struct resource vrtc_resources[] = {
+	[0] = {
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device vrtc_device = {
+	.name		= "rtc_mrst",
+	.id		= -1,
+	.resource	= vrtc_resources,
+	.num_resources	= ARRAY_SIZE(vrtc_resources),
+};
+
+/* Register the RTC device if appropriate */
+static int __init mrst_device_create(void)
+{
+	/* No Moorestown, no device */
+	if (!mrst_identify_cpu())
+		return -ENODEV;
+	/* No timer, no device */
+	if (!sfi_mrtc_num)
+		return -ENODEV;
+
+	/* iomem resource */
+	vrtc_resources[0].start = sfi_mrtc_array[0].phys_addr;
+	vrtc_resources[0].end = sfi_mrtc_array[0].phys_addr +
+				MRST_VRTC_MAP_SZ;
+	/* irq resource */
+	vrtc_resources[1].start = sfi_mrtc_array[0].irq;
+	vrtc_resources[1].end = sfi_mrtc_array[0].irq;
+
+	return platform_device_register(&vrtc_device);
+}
+
+module_init(mrst_device_create);

arch/x86/platform/sfi/sfi.c

@@ -34,17 +34,6 @@
 #ifdef CONFIG_X86_LOCAL_APIC
 static unsigned long sfi_lapic_addr __initdata = APIC_DEFAULT_PHYS_BASE;
 
-static void __init mp_sfi_register_lapic_address(unsigned long address)
-{
-	mp_lapic_addr = address;
-
-	set_fixmap_nocache(FIX_APIC_BASE, mp_lapic_addr);
-	if (boot_cpu_physical_apicid == -1U)
-		boot_cpu_physical_apicid = read_apic_id();
-
-	pr_info("Boot CPU = %d\n", boot_cpu_physical_apicid);
-}
-
 /* All CPUs enumerated by SFI must be present and enabled */
 static void __cpuinit mp_sfi_register_lapic(u8 id)
 {
@@ -110,7 +99,7 @@ static int __init sfi_parse_ioapic(struct sfi_table_header *table)
 int __init sfi_platform_init(void)
 {
 #ifdef CONFIG_X86_LOCAL_APIC
-	mp_sfi_register_lapic_address(sfi_lapic_addr);
+	register_lapic_address(sfi_lapic_addr);
 	sfi_table_parse(SFI_SIG_CPUS, NULL, NULL, sfi_parse_cpus);
 #endif
 #ifdef CONFIG_X86_IO_APIC

drivers/platform/x86/intel_scu_ipc.c

@@ -26,6 +26,7 @@
 #include <linux/sfi.h>
 #include <asm/mrst.h>
 #include <asm/intel_scu_ipc.h>
+#include <asm/mrst.h>
 
 /* IPC defines the following message types */
 #define IPCMSG_WATCHDOG_TIMER 0xF8 /* Set Kernel Watchdog Threshold */
@@ -699,6 +700,9 @@ static int ipc_probe(struct pci_dev *dev, const struct pci_device_id *id)
 		iounmap(ipcdev.ipc_base);
 		return -ENOMEM;
 	}
+
+	intel_scu_devices_create();
+
 	return 0;
 }
 
@@ -720,6 +724,7 @@ static void ipc_remove(struct pci_dev *pdev)
 	iounmap(ipcdev.ipc_base);
 	iounmap(ipcdev.i2c_base);
 	ipcdev.pdev = NULL;
+	intel_scu_devices_destroy();
 }
 
 static const struct pci_device_id pci_ids[] = {

drivers/rtc/Kconfig

@@ -463,6 +463,18 @@ config RTC_DRV_CMOS
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-cmos.
 
+config RTC_DRV_VRTC
+	tristate "Virtual RTC for Moorestown platforms"
+	depends on X86_MRST
+	default y if X86_MRST
+
+	help
+	Say "yes" here to get direct support for the real time clock
+	found on Moorestown platforms. The VRTC is a emulated RTC that
+	derives its clock source from a real RTC in the PMIC. The MC146818
+	style programming interface is mostly conserved, but any
+	updates are done via IPC calls to the system controller FW.
+
 config RTC_DRV_DS1216
 	tristate "Dallas DS1216"
 	depends on SNI_RM

drivers/rtc/Makefile

@@ -30,6 +30,7 @@ obj-$(CONFIG_RTC_DRV_CMOS)	+= rtc-cmos.o
 obj-$(CONFIG_RTC_DRV_COH901331)	+= rtc-coh901331.o
 obj-$(CONFIG_RTC_DRV_DAVINCI)	+= rtc-davinci.o
 obj-$(CONFIG_RTC_DRV_DM355EVM)	+= rtc-dm355evm.o
+obj-$(CONFIG_RTC_DRV_VRTC)	+= rtc-mrst.o
 obj-$(CONFIG_RTC_DRV_DS1216)	+= rtc-ds1216.o
 obj-$(CONFIG_RTC_DRV_DS1286)	+= rtc-ds1286.o
 obj-$(CONFIG_RTC_DRV_DS1302)	+= rtc-ds1302.o

include/linux/sfi.h

@@ -77,6 +77,8 @@
 #define SFI_OEM_ID_SIZE		6
 #define SFI_OEM_TABLE_ID_SIZE	8
 
+#define SFI_NAME_LEN		16
+
 #define SFI_SYST_SEARCH_BEGIN		0x000E0000
 #define SFI_SYST_SEARCH_END		0x000FFFFF
 
@@ -156,13 +158,13 @@ struct sfi_device_table_entry {
 	u16	addr;
 	u8	irq;
 	u32	max_freq;
-	char	name[16];
+	char	name[SFI_NAME_LEN];
 } __packed;
 
 struct sfi_gpio_table_entry {
-	char	controller_name[16];
+	char	controller_name[SFI_NAME_LEN];
 	u16	pin_no;
-	char	pin_name[16];
+	char	pin_name[SFI_NAME_LEN];
 } __packed;
 
 typedef int (*sfi_table_handler) (struct sfi_table_header *table);