phy: Revert "phy: qualcomm: usb28nm: Add MDM9607 init sequence"

This reverts commit 557a2881.

This commit introduced an init sequence from downstream DT [1] in the
driver.  As mentioned by the comment above the HSPHY_INIT_CFG macro for
this sequence:

    /*
     * The macro is used to define an initialization sequence.  Each tuple
     * is meant to program 'value' into phy register at 'offset' with 'delay'
     * in us followed.
     */

Instead of corresponding to offsets into the phy register, the sequence
read by the downstream driver [2] is passed into ulpi_write [3] which
crafts the address-value pair into a new value and writes it into the
same register at USB_ULPI_VIEWPORT [4].  In other words, this init
sequence is programmed into the hardware in a totally different way than
downstream and is unlikely to achieve the desired result, if the hsphy
is working at all.

An alternative method needs to be found to write these init values at
the desired location.  Fortunately mdm9607 did not land upstream yet [5]
and should have its compatible revised to use the generic one, instead
of a compatible that writes wrong data to the wrong registers.

[1]: https://android.googlesource.com/kernel/msm/+/android-7.1.0_r0.2/arch/arm/boot/dts/qcom/mdm9607.dtsi#585
[2]: https://android.googlesource.com/kernel/msm/+/android-7.1.0_r0.2/drivers/usb/phy/phy-msm-usb.c#4183
[3]: https://android.googlesource.com/kernel/msm/+/android-7.1.0_r0.2/drivers/usb/phy/phy-msm-usb.c#468
[4]: https://android.googlesource.com/kernel/msm/+/android-7.1.0_r0.2/drivers/usb/phy/phy-msm-usb.c#418
[5]: https://lore.kernel.org/linux-arm-msm/20210805222812.40731-1-konrad.dybcio@somainline.org/Reported-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20221214223733.648167-1-marijn.suijten@somainline.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml

@@ -16,7 +16,6 @@ properties:
   compatible:
     enum:
       - qcom,usb-hs-28nm-femtophy
-      - qcom,usb-hs-28nm-mdm9607
 
   reg:
     maxItems: 1

drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c

@@ -401,26 +401,13 @@ static const struct hsphy_init_seq init_seq_femtophy[] = {
 	HSPHY_INIT_CFG(0x90, 0x60, 0),
 };
 
-static const struct hsphy_init_seq init_seq_mdm9607[] = {
-	HSPHY_INIT_CFG(0x80, 0x44, 0),
-	HSPHY_INIT_CFG(0x81, 0x38, 0),
-	HSPHY_INIT_CFG(0x82, 0x24, 0),
-	HSPHY_INIT_CFG(0x83, 0x13, 0),
-};
-
 static const struct hsphy_data hsphy_data_femtophy = {
 	.init_seq = init_seq_femtophy,
 	.init_seq_num = ARRAY_SIZE(init_seq_femtophy),
 };
 
-static const struct hsphy_data hsphy_data_mdm9607 = {
-	.init_seq = init_seq_mdm9607,
-	.init_seq_num = ARRAY_SIZE(init_seq_mdm9607),
-};
-
 static const struct of_device_id qcom_snps_hsphy_match[] = {
 	{ .compatible = "qcom,usb-hs-28nm-femtophy", .data = &hsphy_data_femtophy, },
-	{ .compatible = "qcom,usb-hs-28nm-mdm9607", .data = &hsphy_data_mdm9607, },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_match);