Merge tag 'devicetree-for-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull devicetree updates from Rob Herring:
 "Bindings:

   - Add spi-peripheral-props.yaml references to various SPI device
     bindings

   - Convert qcom,pm8916-wdt, ds1307, Qualcomm BAM DMA, is31fl319x,
     skyworks,aat1290, Rockchip EMAC, gpio-ir-receiver, ahci-ceva, Arm
     CCN PMU, rda,8810pl-intc, sil,sii9022, ps2-gpio, and
     arm-firmware-suite bindings to DT schema format

   - New bindings for Arm virtual platforms display, Qualcomm IMEM
     memory region, Samsung S5PV210 ChipID, EM Microelectronic EM3027
     RTC, and arm,cortex-a78ae

   - Add vendor prefixes for asrock, bytedance, hxt, ingrasys, inventec,
     quanta, and densitron

   - Add missing MSI and IOMMU properties to host-generic-pci

   - Remove bindings for removed EFM32 platform

   - Remove old chosen.txt binding (replaced by schema)

   - Treewide add missing type information for properties

   - Treewide fixing of typos and its vs. it's in bindings. Its all good
     now.

   - Drop unnecessary quoting in power related schemas

   - Several LED binding updates which didn't get picked up

   - Move various bindings to proper directories

  DT core code:

   - Convert unittest GPIO related tests to use fwnode

   - Check ima-kexec-buffer against memory bounds

   - Print reserved-memory allocation/reservation failures as errors

   - Cleanup early_init_dt_reserve_memory_arch()

   - Simplify of_overlay_fdt_apply() tail"

* tag 'devicetree-for-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (65 commits)
  dt-bindings: mtd: microchip,mchp48l640: use spi-peripheral-props.yaml
  dt-bindings: power: supply: drop quotes when not needed
  dt-bindings: power: reset: drop quotes when not needed
  dt-bindings: power: drop quotes when not needed
  dt-bindings: PCI: host-generic-pci: Allow IOMMU and MSI properties
  of/fdt: declared return type does not match actual return type
  devicetree/bindings: correct possessive "its" typos
  dt-bindings: net: convert emac_rockchip.txt to YAML
  dt-bindings: eeprom: microchip,93lc46b: move to eeprom directory
  dt-bindings: eeprom: at25: use spi-peripheral-props.yaml
  dt-bindings: display: use spi-peripheral-props.yaml
  dt-bindings: watchdog: qcom,pm8916-wdt: convert to dtschema
  dt-bindings: power: reset: qcom,pon: use absolute path to other schema
  dt-bindings: iio/dac: adi,ad5766: Add missing type to 'output-range-microvolts'
  dt-bindings: power: supply: charger-manager: Add missing type for 'cm-battery-stat'
  dt-bindings: panel: raydium,rm67191: Add missing type to 'video-mode'
  of/fdt: Clean up early_init_dt_reserve_memory_arch()
  dt-bindings: PCI: fsl,imx6q-pcie: Add missing type for 'reset-gpio-active-high'
  dt-bindings: rtc: Add EM Microelectronic EM3027 bindings
  dt-bindings: rtc: ds1307: Convert to json-schema
  ...

Documentation/devicetree/bindings/arm/cpus.yaml

@@ -138,6 +138,7 @@ properties:
       - arm,cortex-a76
       - arm,cortex-a77
       - arm,cortex-a78
+      - arm,cortex-a78ae
       - arm,cortex-a510
       - arm,cortex-a710
       - arm,cortex-m0

Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt

@@ -10,7 +10,7 @@ system, notifying them when a low power state is entered or exited.
 Multiple revisions of the SAW hardware are supported using these Device Nodes.
 SAW2 revisions differ in the register offset and configuration data. Also, the
 same revision of the SAW in different SoCs may have different configuration
-data due the the differences in hardware capabilities. Hence the SoC name, the
+data due the differences in hardware capabilities. Hence the SoC name, the
 version of the SAW hardware in that SoC and the distinction between cpu (big
 or Little) or cache, may be needed to uniquely identify the SAW register
 configuration and initialization data. The compatible string is used to

Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml

@@ -208,7 +208,7 @@ properties:
       "^[a-z0-9]+$":
         type: object
 
-        patternProperties:
+        properties:
           clocks:
             minItems: 1
             maxItems: 8

Documentation/devicetree/bindings/arm/vexpress-sysreg.yaml

@@ -29,6 +29,13 @@ properties:
 
   ranges: true
 
+  gpio-controller:
+    deprecated: true
+
+  "#gpio-cells":
+    deprecated: true
+    const: 2
+
 additionalProperties: false
 
 patternProperties:
@@ -67,8 +74,7 @@ patternProperties:
 
 required:
   - compatible
-  - "#address-cells"
-  - "#size-cells"
+  - reg
 
 examples:
   - |

Documentation/devicetree/bindings/ata/ahci-ceva.txt

-Binding for CEVA AHCI SATA Controller
-
-Required properties:
-  - reg: Physical base address and size of the controller's register area.
-  - compatible: Compatibility string. Must be 'ceva,ahci-1v84'.
-  - clocks: Input clock specifier. Refer to common clock bindings.
-  - interrupts: Interrupt specifier. Refer to interrupt binding.
-  - ceva,p0-cominit-params: OOB timing value for COMINIT parameter for port 0.
-  - ceva,p1-cominit-params: OOB timing value for COMINIT parameter for port 1.
-			The fields for the above parameter must be as shown below:
-			ceva,pN-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>;
-			CINMP : COMINIT Negate Minimum Period.
-			CIBGN : COMINIT Burst Gap Nominal.
-			CIBGMX: COMINIT Burst Gap Maximum.
-			CIBGMN: COMINIT Burst Gap Minimum.
-  - ceva,p0-comwake-params: OOB timing value for COMWAKE parameter for port 0.
-  - ceva,p1-comwake-params: OOB timing value for COMWAKE parameter for port 1.
-			The fields for the above parameter must be as shown below:
-			ceva,pN-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>;
-			CWBGMN: COMWAKE Burst Gap Minimum.
-			CWBGMX: COMWAKE Burst Gap Maximum.
-			CWBGN: COMWAKE Burst Gap Nominal.
-			CWNMP: COMWAKE Negate Minimum Period.
-  - ceva,p0-burst-params: Burst timing value for COM parameter for port 0.
-  - ceva,p1-burst-params: Burst timing value for COM parameter for port 1.
-			The fields for the above parameter must be as shown below:
-			ceva,pN-burst-params = /bits/ 8 <BMX BNM SFD PTST>;
-			BMX: COM Burst Maximum.
-			BNM: COM Burst Nominal.
-			SFD: Signal Failure Detection value.
-			PTST: Partial to Slumber timer value.
-  - ceva,p0-retry-params: Retry interval timing value for port 0.
-  - ceva,p1-retry-params: Retry interval timing value for port 1.
-			The fields for the above parameter must be as shown below:
-			ceva,pN-retry-params = /bits/ 16 <RIT RCT>;
-			RIT:  Retry Interval Timer.
-			RCT:  Rate Change Timer.
-
-Optional properties:
-  - ceva,broken-gen2: limit to gen1 speed instead of gen2.
-  - phys: phandle for the PHY device
-  - resets: phandle to the reset controller for the SATA IP
-
-Examples:
-	ahci@fd0c0000 {
-		compatible = "ceva,ahci-1v84";
-		reg = <0xfd0c0000 0x200>;
-		interrupt-parent = <&gic>;
-		interrupts = <0 133 4>;
-		clocks = <&clkc SATA_CLK_ID>;
-		ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
-		ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
-		ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
-		ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>;
-
-		ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
-		ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
-		ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
-		ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>;
-		ceva,broken-gen2;
-		phys = <&psgtr 1 PHY_TYPE_SATA 1 1>;
-		resets = <&zynqmp_reset ZYNQMP_RESET_SATA>;
-	};

Documentation/devicetree/bindings/ata/ceva,ahci-1v84.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/ata/ceva,ahci-1v84.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ceva AHCI SATA Controller
+
+maintainers:
+  - Piyush Mehta <piyush.mehta@xilinx.com>
+
+description: |
+  The Ceva SATA controller mostly conforms to the AHCI interface with some
+  special extensions to add functionality, is a high-performance dual-port
+  SATA host controller with an AHCI compliant command layer which supports
+  advanced features such as native command queuing and frame information
+  structure (FIS) based switching for systems employing port multipliers.
+
+properties:
+  compatible:
+    const: ceva,ahci-1v84
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  dma-coherent: true
+
+  interrupts:
+    maxItems: 1
+
+  iommus:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  ceva,p0-cominit-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      OOB timing value for COMINIT parameter for port 0.
+      The fields for the above parameter must be as shown below:-
+      ceva,p0-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>;
+    items:
+      - description: CINMP - COMINIT Negate Minimum Period.
+      - description: CIBGN - COMINIT Burst Gap Nominal.
+      - description: CIBGMX - COMINIT Burst Gap Maximum.
+      - description: CIBGMN - COMINIT Burst Gap Minimum.
+
+  ceva,p0-comwake-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      OOB timing value for COMWAKE parameter for port 0.
+      The fields for the above parameter must be as shown below:-
+      ceva,p0-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>;
+    items:
+      - description: CWBGMN - COMWAKE Burst Gap Minimum.
+      - description: CWBGMX - COMWAKE Burst Gap Maximum.
+      - description: CWBGN - COMWAKE Burst Gap Nominal.
+      - description: CWNMP - COMWAKE Negate Minimum Period.
+
+  ceva,p0-burst-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      Burst timing value for COM parameter for port 0.
+      The fields for the above parameter must be as shown below:-
+      ceva,p0-burst-params = /bits/ 8 <BMX BNM SFD PTST>;
+    items:
+      - description: BMX - COM Burst Maximum.
+      - description: BNM - COM Burst Nominal.
+      - description: SFD - Signal Failure Detection value.
+      - description: PTST - Partial to Slumber timer value.
+
+  ceva,p0-retry-params:
+    $ref: /schemas/types.yaml#/definitions/uint16-array
+    description: |
+      Retry interval timing value for port 0.
+      The fields for the above parameter must be as shown below:-
+      ceva,p0-retry-params = /bits/ 16 <RIT RCT>;
+    items:
+      - description: RIT - Retry Interval Timer.
+      - description: RCT - Rate Change Timer.
+
+  ceva,p1-cominit-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      OOB timing value for COMINIT parameter for port 1.
+      The fields for the above parameter must be as shown below:-
+      ceva,p1-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>;
+    items:
+      - description: CINMP - COMINIT Negate Minimum Period.
+      - description: CIBGN - COMINIT Burst Gap Nominal.
+      - description: CIBGMX - COMINIT Burst Gap Maximum.
+      - description: CIBGMN - COMINIT Burst Gap Minimum.
+
+  ceva,p1-comwake-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      OOB timing value for COMWAKE parameter for port 1.
+      The fields for the above parameter must be as shown below:-
+      ceva,p1-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>;
+    items:
+      - description: CWBGMN - COMWAKE Burst Gap Minimum.
+      - description: CWBGMX - COMWAKE Burst Gap Maximum.
+      - description: CWBGN - COMWAKE Burst Gap Nominal.
+      - description: CWNMP - COMWAKE Negate Minimum Period.
+
+  ceva,p1-burst-params:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    description: |
+      Burst timing value for COM parameter for port 1.
+      The fields for the above parameter must be as shown below:-
+      ceva,p1-burst-params = /bits/ 8 <BMX BNM SFD PTST>;
+    items:
+      - description: BMX - COM Burst Maximum.
+      - description: BNM - COM Burst Nominal.
+      - description: SFD - Signal Failure Detection value.
+      - description: PTST - Partial to Slumber timer value.
+
+  ceva,p1-retry-params:
+    $ref: /schemas/types.yaml#/definitions/uint16-array
+    description: |
+      Retry interval timing value for port 1.
+      The fields for the above parameter must be as shown below:-
+      ceva,pN-retry-params = /bits/ 16 <RIT RCT>;
+    items:
+      - description: RIT - Retry Interval Timer.
+      - description: RCT - Rate Change Timer.
+
+  ceva,broken-gen2:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: |
+      limit to gen1 speed instead of gen2.
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    items:
+      - const: sata-phy
+
+  resets:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+  - ceva,p0-cominit-params
+  - ceva,p0-comwake-params
+  - ceva,p0-burst-params
+  - ceva,p0-retry-params
+  - ceva,p1-cominit-params
+  - ceva,p1-comwake-params
+  - ceva,p1-burst-params
+  - ceva,p1-retry-params
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/xlnx-zynqmp-clk.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/power/xlnx-zynqmp-power.h>
+    #include <dt-bindings/reset/xlnx-zynqmp-resets.h>
+    #include <dt-bindings/clock/xlnx-zynqmp-clk.h>
+    #include <dt-bindings/phy/phy.h>
+
+    sata: ahci@fd0c0000 {
+        compatible = "ceva,ahci-1v84";
+        reg = <0xfd0c0000 0x200>;
+        interrupt-parent = <&gic>;
+        interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&zynqmp_clk SATA_REF>;
+        ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
+        ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
+        ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
+        ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>;
+        ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
+        ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
+        ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
+        ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>;
+        ceva,broken-gen2;
+        phys = <&psgtr 1 PHY_TYPE_SATA 1 1>;
+        resets = <&zynqmp_reset ZYNQMP_RESET_SATA>;
+    };

Documentation/devicetree/bindings/bus/qcom,ssc-block-bus.yaml

@@ -28,11 +28,9 @@ properties:
       - const: qcom,ssc-block-bus
 
   reg:
-    description: |
-      Shall contain the addresses of the SSCAON_CONFIG0 and SSCAON_CONFIG1
-      registers
-    minItems: 2
-    maxItems: 2
+    items:
+      - description: SSCAON_CONFIG0 registers
+      - description: SSCAON_CONFIG1 registers
 
   reg-names:
     items:
@@ -48,7 +46,6 @@ properties:
   ranges: true
 
   clocks:
-    minItems: 6
     maxItems: 6
 
   clock-names:
@@ -61,9 +58,9 @@ properties:
       - const: ssc_ahbs
 
   power-domains:
-    description: Power domain phandles for the ssc_cx and ssc_mx power domains
-    minItems: 2
-    maxItems: 2
+    items:
+      - description: CX power domain
+      - description: MX power domain
 
   power-domain-names:
     items:
@@ -71,11 +68,11 @@ properties:
       - const: ssc_mx
 
   resets:
-    description: |
-      Reset phandles for the ssc_reset and ssc_bcr resets (note: ssc_bcr is the
-      branch control register associated with the ssc_xo and ssc_ahbs clocks)
-    minItems: 2
-    maxItems: 2
+    items:
+      - description: Main reset
+      - description:
+          SSC Branch Control Register reset (associated with the ssc_xo and
+          ssc_ahbs clocks)
 
   reset-names:
     items:

Documentation/devicetree/bindings/chosen.txt

-The chosen node
----------------
-
-The chosen node does not represent a real device, but serves as a place
-for passing data between firmware and the operating system, like boot
-arguments. Data in the chosen node does not represent the hardware.
-
-The following properties are recognized:
-
-
-kaslr-seed
------------
-
-This property is used when booting with CONFIG_RANDOMIZE_BASE as the
-entropy used to randomize the kernel image base address location. Since
-it is used directly, this value is intended only for KASLR, and should
-not be used for other purposes (as it may leak information about KASLR
-offsets). It is parsed as a u64 value, e.g.
-
-/ {
-	chosen {
-		kaslr-seed = <0xfeedbeef 0xc0def00d>;
-	};
-};
-
-Note that if this property is set from UEFI (or a bootloader in EFI
-mode) when EFI_RNG_PROTOCOL is supported, it will be overwritten by
-the Linux EFI stub (which will populate the property itself, using
-EFI_RNG_PROTOCOL).
-
-stdout-path
------------
-
-Device trees may specify the device to be used for boot console output
-with a stdout-path property under /chosen, as described in the Devicetree
-Specification, e.g.
-
-/ {
-	chosen {
-		stdout-path = "/serial@f00:115200";
-	};
-
-	serial@f00 {
-		compatible = "vendor,some-uart";
-		reg = <0xf00 0x10>;
-	};
-};
-
-If the character ":" is present in the value, this terminates the path.
-The meaning of any characters following the ":" is device-specific, and
-must be specified in the relevant binding documentation.
-
-For UART devices, the preferred binding is a string in the form:
-
-	<baud>{<parity>{<bits>{<flow>}}}
-
-where
-
-	baud	- baud rate in decimal
-	parity	- 'n' (none), 'o', (odd) or 'e' (even)
-	bits	- number of data bits
-	flow	- 'r' (rts)
-
-For example: 115200n8r
-
-Implementation note: Linux will look for the property "linux,stdout-path" or
-on PowerPC "stdout" if "stdout-path" is not found.  However, the
-"linux,stdout-path" and "stdout" properties are deprecated. New platforms
-should only use the "stdout-path" property.
-
-linux,booted-from-kexec
------------------------
-
-This property is set (currently only on PowerPC, and only needed on
-book3e) by some versions of kexec-tools to tell the new kernel that it
-is being booted by kexec, as the booting environment may differ (e.g.
-a different secondary CPU release mechanism)
-
-linux,usable-memory-range
--------------------------
-
-This property holds a base address and size, describing a limited region in
-which memory may be considered available for use by the kernel. Memory outside
-of this range is not available for use.
-
-This property describes a limitation: memory within this range is only
-valid when also described through another mechanism that the kernel
-would otherwise use to determine available memory (e.g. memory nodes
-or the EFI memory map). Valid memory may be sparse within the range.
-e.g.
-
-/ {
-	chosen {
-		linux,usable-memory-range = <0x9 0xf0000000 0x0 0x10000000>;
-	};
-};
-
-The main usage is for crash dump kernel to identify its own usable
-memory and exclude, at its boot time, any other memory areas that are
-part of the panicked kernel's memory.
-
-While this property does not represent a real hardware, the address
-and the size are expressed in #address-cells and #size-cells,
-respectively, of the root node.
-
-linux,elfcorehdr
-----------------
-
-This property holds the memory range, the address and the size, of the elf
-core header which mainly describes the panicked kernel's memory layout as
-PT_LOAD segments of elf format.
-e.g.
-
-/ {
-	chosen {
-		linux,elfcorehdr = <0x9 0xfffff000 0x0 0x800>;
-	};
-};
-
-While this property does not represent a real hardware, the address
-and the size are expressed in #address-cells and #size-cells,
-respectively, of the root node.
-
-linux,initrd-start and linux,initrd-end
----------------------------------------
-
-These properties hold the physical start and end address of an initrd that's
-loaded by the bootloader. Note that linux,initrd-start is inclusive, but
-linux,initrd-end is exclusive.
-e.g.
-
-/ {
-	chosen {
-		linux,initrd-start = <0x82000000>;
-		linux,initrd-end = <0x82800000>;
-	};
-};

Documentation/devicetree/bindings/clock/efm32-clock.txt

-* Clock bindings for Energy Micro efm32 Giant Gecko's Clock Management Unit
-
-Required properties:
-- compatible: Should be "efm32gg,cmu"
-- reg: Base address and length of the register set
-- interrupts: Interrupt used by the CMU
-- #clock-cells: Should be <1>
-
-The clock consumer should specify the desired clock by having the clock ID in
-its "clocks" phandle cell. The header efm32-clk.h contains a list of available
-IDs.

Documentation/devicetree/bindings/clock/st/st,flexgen.txt

@@ -78,7 +78,7 @@ Required properties:
 - #clock-cells : from common clock binding; shall be set to 1 (multiple clock
   outputs).
 
-- clocks : must be set to the parent's phandle. it's could be output clocks of
+- clocks : must be set to the parent's phandle. it could be output clocks of
   a quadsfs or/and a pll or/and clk_sysin (up to 7 clocks)
 
 - clock-output-names : List of strings used to name the clock outputs.

Documentation/devicetree/bindings/clock/ti/davinci/pll.txt

@@ -15,7 +15,7 @@ Required properties:
 	- for "ti,da850-pll1", shall be "clksrc"
 
 Optional properties:
-- ti,clkmode-square-wave: Indicates that the the board is supplying a square
+- ti,clkmode-square-wave: Indicates that the board is supplying a square
 	wave input on the OSCIN pin instead of using a crystal oscillator.
 	This property is only valid when compatible = "ti,da850-pll0".
 

Documentation/devicetree/bindings/clock/ti/dra7-atl.txt

@@ -6,7 +6,7 @@ functional clock but can be configured to provide different clocks.
 ATL can maintain a clock averages to some desired frequency based on the bws/aws
 signals - can compensate the drift between the two ws signal.
 
-In order to provide the support for ATL and it's output clocks (which can be used
+In order to provide the support for ATL and its output clocks (which can be used
 internally within the SoC or external components) two sets of bindings is needed:
 
 Clock tree binding:

Documentation/devicetree/bindings/connector/usb-connector.yaml

@@ -263,11 +263,11 @@ examples:
   # Micro-USB connector with HS lines routed via controller (MUIC).
   - |
     muic-max77843 {
-      usb_con1: connector {
-        compatible = "usb-b-connector";
-        label = "micro-USB";
-        type = "micro";
-      };
+        usb_con1: connector {
+            compatible = "usb-b-connector";
+            label = "micro-USB";
+            type = "micro";
+        };
     };
 
   # USB-C connector attached to CC controller (s2mm005), HS lines routed
@@ -275,34 +275,34 @@ examples:
   # DisplayPort video lines are routed to the connector via SS mux in USB3 PHY.
   - |
     ccic: s2mm005 {
-      usb_con2: connector {
-        compatible = "usb-c-connector";
-        label = "USB-C";
+        usb_con2: connector {
+            compatible = "usb-c-connector";
+            label = "USB-C";
 
-        ports {
-          #address-cells = <1>;
-          #size-cells = <0>;
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
 
-          port@0 {
-            reg = <0>;
-            usb_con_hs: endpoint {
-              remote-endpoint = <&max77865_usbc_hs>;
-            };
-          };
-          port@1 {
-            reg = <1>;
-            usb_con_ss: endpoint {
-              remote-endpoint = <&usbdrd_phy_ss>;
-            };
-          };
-          port@2 {
-            reg = <2>;
-            usb_con_sbu: endpoint {
-              remote-endpoint = <&dp_aux>;
+                port@0 {
+                    reg = <0>;
+                    usb_con_hs: endpoint {
+                        remote-endpoint = <&max77865_usbc_hs>;
+                    };
+                };
+                port@1 {
+                    reg = <1>;
+                    usb_con_ss: endpoint {
+                        remote-endpoint = <&usbdrd_phy_ss>;
+                    };
+                };
+                port@2 {
+                    reg = <2>;
+                    usb_con_sbu: endpoint {
+                        remote-endpoint = <&dp_aux>;
+                    };
+                };
             };
-          };
         };
-      };
     };
 
   # USB-C connector attached to a typec port controller(ptn5110), which has
@@ -310,16 +310,16 @@ examples:
   - |
     #include <dt-bindings/usb/pd.h>
     typec: ptn5110 {
-      usb_con3: connector {
-        compatible = "usb-c-connector";
-        label = "USB-C";
-        power-role = "dual";
-        try-power-role = "sink";
-        source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
-        sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)
-                     PDO_VAR(5000, 12000, 2000)>;
-        op-sink-microwatt = <10000000>;
-      };
+        usb_con3: connector {
+            compatible = "usb-c-connector";
+            label = "USB-C";
+            power-role = "dual";
+            try-power-role = "sink";
+            source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
+            sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)
+                         PDO_VAR(5000, 12000, 2000)>;
+            op-sink-microwatt = <10000000>;
+        };
     };
 
   # USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220)
@@ -332,20 +332,20 @@ examples:
         data-role = "dual";
 
         ports {
-                #address-cells = <1>;
-                #size-cells = <0>;
-                port@0 {
-                        reg = <0>;
-                        hs_ep: endpoint {
-                                remote-endpoint = <&usb3_hs_ep>;
-                        };
+            #address-cells = <1>;
+            #size-cells = <0>;
+            port@0 {
+                reg = <0>;
+                hs_ep: endpoint {
+                    remote-endpoint = <&usb3_hs_ep>;
                 };
-                port@1 {
-                        reg = <1>;
-                        ss_ep: endpoint {
-                                remote-endpoint = <&hd3ss3220_in_ep>;
-                        };
+            };
+            port@1 {
+                reg = <1>;
+                ss_ep: endpoint {
+                    remote-endpoint = <&hd3ss3220_in_ep>;
                 };
+            };
         };
     };
 
@@ -354,12 +354,12 @@ examples:
     #include <dt-bindings/gpio/gpio.h>
 
     usb {
-      connector {
-        compatible = "gpio-usb-b-connector", "usb-b-connector";
-        type = "micro";
-        id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
-        vbus-supply = <&usb_p0_vbus>;
-      };
+        connector {
+            compatible = "gpio-usb-b-connector", "usb-b-connector";
+            type = "micro";
+            id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
+            vbus-supply = <&usb_p0_vbus>;
+        };
     };
 
   # Micro-USB connector with HS lines routed via controller (MUIC) and MHL
@@ -367,27 +367,27 @@ examples:
   # mobile phone
   - |
     muic-max77843 {
-      usb_con4: connector {
-        compatible = "samsung,usb-connector-11pin", "usb-b-connector";
-        label = "micro-USB";
-        type = "micro";
+        usb_con4: connector {
+            compatible = "samsung,usb-connector-11pin", "usb-b-connector";
+            label = "micro-USB";
+            type = "micro";
 
-        ports {
-          #address-cells = <1>;
-          #size-cells = <0>;
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
 
-          port@0 {
-            reg = <0>;
-            muic_to_usb: endpoint {
-              remote-endpoint = <&usb_to_muic>;
-            };
-          };
-          port@3 {
-            reg = <3>;
-            usb_con_mhl: endpoint {
-              remote-endpoint = <&sii8620_mhl>;
+                port@0 {
+                    reg = <0>;
+                    muic_to_usb: endpoint {
+                        remote-endpoint = <&usb_to_muic>;
+                    };
+                };
+                port@3 {
+                    reg = <3>;
+                    usb_con_mhl: endpoint {
+                        remote-endpoint = <&sii8620_mhl>;
+                    };
+                };
             };
-          };
         };
-      };
     };

Documentation/devicetree/bindings/display/arm,pl11x.yaml

@@ -159,25 +159,12 @@ examples:
     };
 
     panel {
-        compatible = "arm,rtsm-display", "panel-dpi";
-        power-supply = <&vcc_supply>;
+        compatible = "arm,rtsm-display";
 
         port {
             clcd_panel: endpoint {
                 remote-endpoint = <&clcd_pads>;
             };
         };
-
-        panel-timing {
-            clock-frequency = <25175000>;
-            hactive = <640>;
-            hback-porch = <40>;
-            hfront-porch = <24>;
-            hsync-len = <96>;
-            vactive = <480>;
-            vback-porch = <32>;
-            vfront-porch = <11>;
-            vsync-len = <2>;
-        };
     };
 ...

Documentation/devicetree/bindings/display/bridge/sii902x.txt

-sii902x HDMI bridge bindings
-
-Required properties:
-	- compatible: "sil,sii9022"
-	- reg: i2c address of the bridge
-
-Optional properties:
-	- interrupts: describe the interrupt line used to inform the host
-	  about hotplug events.
-	- reset-gpios: OF device-tree gpio specification for RST_N pin.
-	- iovcc-supply: I/O Supply Voltage (1.8V or 3.3V)
-	- cvcc12-supply: Digital Core Supply Voltage (1.2V)
-
-	HDMI audio properties:
-	- #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin
-	   is wired, <1> if the both are wired. HDMI audio is
-	   configured only if this property is found.
-	- sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3
-	   Each integer indicates which i2s pin is connected to which
-	   audio fifo. The first integer selects i2s audio pin for the
-	   first audio fifo#0 (HDMI channels 1&2), second for fifo#1
-	   (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s
-	   pins (SD0 - SD3). Any i2s pin can be connected to any fifo,
-	   but there can be no gaps. E.g. an i2s pin must be mapped to
-	   fifo#0 and fifo#1 before mapping a channel to fifo#2. Default
-	   value is <0>, describing SD0 pin beiging routed to hdmi audio
-	   fifo #0.
-	- clocks: phandle and clock specifier for each clock listed in
-           the clock-names property
-	- clock-names: "mclk"
-	   Describes SII902x MCLK input. MCLK can be used to produce
-	   HDMI audio CTS values. This property follows
-	   Documentation/devicetree/bindings/clock/clock-bindings.txt
-	   consumer binding.
-
-	If HDMI audio is configured the sii902x device becomes an I2S
-	and/or spdif audio codec component (e.g a digital audio sink),
-	that can be used in configuring a full audio devices with
-	simple-card or audio-graph-card binding. See their binding
-	documents on how to describe the way the sii902x device is
-	connected to the rest of the audio system:
-	Documentation/devicetree/bindings/sound/simple-card.yaml
-	Documentation/devicetree/bindings/sound/audio-graph-card.yaml
-	Note: In case of the audio-graph-card binding the used port
-	index should be 3.
-
-Optional subnodes:
-	- video input: this subnode can contain a video input port node
-	  to connect the bridge to a display controller output (See this
-	  documentation [1]).
-
-[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Example:
-	hdmi-bridge@39 {
-		compatible = "sil,sii9022";
-		reg = <0x39>;
-		reset-gpios = <&pioA 1 0>;
-		iovcc-supply = <&v3v3_hdmi>;
-		cvcc12-supply = <&v1v2_hdmi>;
-
-		#sound-dai-cells = <0>;
-		sil,i2s-data-lanes = < 0 1 2 >;
-		clocks = <&mclk>;
-		clock-names = "mclk";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				bridge_in: endpoint {
-					remote-endpoint = <&dc_out>;
-				};
-			};
-		};
-	};

Documentation/devicetree/bindings/display/bridge/sil,sii9022.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/sil,sii9022.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Image sii902x HDMI bridge
+
+maintainers:
+  - Boris Brezillon <bbrezillon@kernel.org>
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - sil,sii9022-cpi # CEC Programming Interface
+              - sil,sii9022-tpi # Transmitter Programming Interface
+          - const: sil,sii9022
+      - const: sil,sii9022
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+    description: Interrupt line used to inform the host about hotplug events.
+
+  reset-gpios:
+    maxItems: 1
+
+  iovcc-supply:
+    description: I/O Supply Voltage (1.8V or 3.3V)
+
+  cvcc12-supply:
+    description: Digital Core Supply Voltage (1.2V)
+
+  '#sound-dai-cells':
+    enum: [ 0, 1 ]
+    description: |
+      <0> if only I2S or S/PDIF pin is wired,
+      <1> if both are wired.
+      HDMI audio is configured only if this property is found.
+      If HDMI audio is configured, the sii902x device becomes an I2S and/or
+      S/PDIF audio codec component (e.g. a digital audio sink), that can be
+      used in configuring full audio devices with simple-card or
+      audio-graph-card bindings. See their binding documents on how to describe
+      the way the
+      sii902x device is connected to the rest of the audio system:
+      Documentation/devicetree/bindings/sound/simple-card.yaml
+      Documentation/devicetree/bindings/sound/audio-graph-card.yaml
+      Note: In case of the audio-graph-card binding the used port index should
+      be 3.
+
+  sil,i2s-data-lanes:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    maxItems: 4
+    uniqueItems: true
+    items:
+      enum: [ 0, 1, 2, 3 ]
+    description:
+      Each integer indicates which I2S pin is connected to which audio FIFO.
+      The first integer selects the I2S audio pin for the first audio FIFO#0
+      (HDMI channels 1&2), the second for FIFO#1 (HDMI channels 3&4), and so
+      on. There are 4 FIFOs and 4 I2S pins (SD0 - SD3). Any I2S pin can be
+      connected to any FIFO, but there can be no gaps. E.g. an I2S pin must be
+      mapped to FIFO#0 and FIFO#1 before mapping a channel to FIFO#2. The
+      default value is <0>, describing SD0 pin being routed to HDMI audio
+      FIFO#0.
+
+  clocks:
+    maxItems: 1
+    description: MCLK input. MCLK can be used to produce HDMI audio CTS values.
+
+  clock-names:
+    const: mclk
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Parallel RGB input port
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: HDMI output port
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Sound input port
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        hdmi-bridge@39 {
+            compatible = "sil,sii9022";
+            reg = <0x39>;
+            reset-gpios = <&pioA 1 0>;
+            iovcc-supply = <&v3v3_hdmi>;
+            cvcc12-supply = <&v1v2_hdmi>;
+
+            #sound-dai-cells = <0>;
+            sil,i2s-data-lanes = < 0 1 2 >;
+            clocks = <&mclk>;
+            clock-names = "mclk";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    bridge_in: endpoint {
+                        remote-endpoint = <&dc_out>;
+                    };
+                };
+            };
+        };
+    };

Documentation/devicetree/bindings/display/panel/arm,rtsm-display.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/arm,rtsm-display.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Arm RTSM Virtual Platforms Display
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    const: arm,rtsm-display
+
+  port: true
+
+required:
+  - compatible
+  - port
+
+additionalProperties: false
+
+...

Documentation/devicetree/bindings/display/panel/lg,lg4573.yaml

@@ -15,13 +15,13 @@ maintainers:
 
 allOf:
   - $ref: panel-common.yaml#
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
 
 properties:
   compatible:
     const: lg,lg4573
 
   reg: true
-  spi-max-frequency: true
 
 required:
   - compatible

Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml

@@ -38,6 +38,7 @@ properties:
       0 - burst-mode
       1 - non-burst with sync event
       2 - non-burst with sync pulse
+    $ref: /schemas/types.yaml#/definitions/uint32
     enum: [0, 1, 2]
 
 required:

Documentation/devicetree/bindings/display/sitronix,st7735r.yaml

@@ -15,6 +15,7 @@ description:
 
 allOf:
   - $ref: panel/panel-common.yaml#
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
 
 properties:
   compatible:

Documentation/devicetree/bindings/display/solomon,ssd1307fb.yaml

@@ -49,9 +49,6 @@ properties:
   vbat-supply:
     description: The supply for VBAT
 
-  # Only required for SPI
-  spi-max-frequency: true
-
   solomon,height:
     $ref: /schemas/types.yaml#/definitions/uint32
     default: 16
@@ -153,6 +150,8 @@ required:
   - reg
 
 allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
   - if:
       properties:
         compatible:
@@ -223,7 +222,7 @@ allOf:
         solomon,dclk-frq:
           default: 10
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:
   - |

Documentation/devicetree/bindings/dma/qcom,bam-dma.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/qcom,bam-dma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies Inc BAM DMA controller
+
+maintainers:
+  - Andy Gross <agross@kernel.org>
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+allOf:
+  - $ref: "dma-controller.yaml#"
+
+properties:
+  compatible:
+    enum:
+        # APQ8064, IPQ8064 and MSM8960
+      - qcom,bam-v1.3.0
+        # MSM8974, APQ8074 and APQ8084
+      - qcom,bam-v1.4.0
+        # MSM8916
+      - qcom,bam-v1.7.0
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: bam_clk
+
+  "#dma-cells":
+    const: 1
+
+  interrupts:
+    maxItems: 1
+
+  iommus:
+    minItems: 1
+    maxItems: 4
+
+  num-channels:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Indicates supported number of DMA channels in a remotely controlled bam.
+
+  qcom,controlled-remotely:
+    type: boolean
+    description:
+      Indicates that the bam is controlled by remote proccessor i.e. execution
+      environment.
+
+  qcom,ee:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 7
+    description:
+      Indicates the active Execution Environment identifier (0-7) used in the
+      secure world.
+
+  qcom,num-ees:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Indicates supported number of Execution Environments in a remotely
+      controlled bam.
+
+  qcom,powered-remotely:
+    type: boolean
+    description:
+      Indicates that the bam is powered up by a remote processor but must be
+      initialized by the local processor.
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - "#dma-cells"
+  - interrupts
+  - qcom,ee
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/qcom,gcc-msm8974.h>
+
+    dma-controller@f9944000 {
+        compatible = "qcom,bam-v1.4.0";
+        reg = <0xf9944000 0x15000>;
+        interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+        clock-names = "bam_clk";
+        #dma-cells = <1>;
+        qcom,ee = <0>;
+    };
+...

Documentation/devicetree/bindings/dma/qcom_bam_dma.txt

-QCOM BAM DMA controller
-
-Required properties:
-- compatible: must be one of the following:
- * "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084
- * "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960
- * "qcom,bam-v1.7.0" for MSM8916
-- reg: Address range for DMA registers
-- interrupts: Should contain the one interrupt shared by all channels
-- #dma-cells: must be <1>, the cell in the dmas property of the client device
-  represents the channel number
-- clocks: required clock
-- clock-names: must contain "bam_clk" entry
-- qcom,ee : indicates the active Execution Environment identifier (0-7) used in
-  the secure world.
-- qcom,controlled-remotely : optional, indicates that the bam is controlled by
-  remote proccessor i.e. execution environment.
-- qcom,powered-remotely : optional, indicates that the bam is powered up by
-  a remote processor but must be initialized by the local processor.
-- num-channels : optional, indicates supported number of DMA channels in a
-  remotely controlled bam.
-- qcom,num-ees : optional, indicates supported number of Execution Environments
-  in a remotely controlled bam.
-
-Example:
-
-	uart-bam: dma@f9984000 = {
-		compatible = "qcom,bam-v1.4.0";
-		reg = <0xf9984000 0x15000>;
-		interrupts = <0 94 0>;
-		clocks = <&gcc GCC_BAM_DMA_AHB_CLK>;
-		clock-names = "bam_clk";
-		#dma-cells = <1>;
-		qcom,ee = <0>;
-	};
-
-DMA clients must use the format described in the dma.txt file, using a two cell
-specifier for each channel.
-
-Example:
-	serial@f991e000 {
-		compatible = "qcom,msm-uart";
-		reg = <0xf991e000 0x1000>
-			<0xf9944000 0x19000>;
-		interrupts = <0 108 0>;
-		clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
-			<&gcc GCC_BLSP1_AHB_CLK>;
-		clock-names = "core", "iface";
-
-		dmas = <&uart-bam 0>, <&uart-bam 1>;
-		dma-names = "rx", "tx";
-	};

Documentation/devicetree/bindings/eeprom/at25.yaml

@@ -44,8 +44,6 @@ properties:
   reg:
     maxItems: 1
 
-  spi-max-frequency: true
-
   pagesize:
     $ref: /schemas/types.yaml#/definitions/uint32
     enum: [1, 8, 16, 32, 64, 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768, 65536, 131072]
@@ -105,6 +103,7 @@ required:
   - spi-max-frequency
 
 allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
   - if:
       properties:
         compatible:
@@ -117,7 +116,7 @@ allOf:
         - size
         - address-width
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:
   - |

Documentation/devicetree/bindings/misc/eeprom-93xx46.yaml → Documentation/devicetree/bindings/eeprom/microchip,93lc46b.yaml

 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
 %YAML 1.2
 ---
-$id: http://devicetree.org/schemas/misc/eeprom-93xx46.yaml#
+$id: http://devicetree.org/schemas/eeprom/microchip,93lc46b.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Microchip 93xx46 SPI compatible EEPROM family dt bindings
@@ -28,9 +28,6 @@ properties:
     description: chip select of EEPROM
     maxItems: 1
 
-  spi-max-frequency: true
-  spi-cs-high: true
-
   read-only:
     description:
       parameter-less property which disables writes to the EEPROM
@@ -42,14 +39,16 @@ properties:
       of EEPROM (e.g. for SPI bus multiplexing)
     maxItems: 1
 
-
 required:
   - compatible
   - reg
   - data-size
   - spi-max-frequency
 
-additionalProperties: false
+allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+unevaluatedProperties: false
 
 examples:
   - |

Documentation/devicetree/bindings/fpga/fpga-region.txt

@@ -330,7 +330,7 @@ succeeded.
 
 The Device Tree Overlay will contain:
  * "target-path" or "target"
-   The insertion point where the the contents of the overlay will go into the
+   The insertion point where the contents of the overlay will go into the
    live tree.  target-path is a full path, while target is a phandle.
  * "ranges"
     The address space mapping from processor to FPGA bus(ses).

Documentation/devicetree/bindings/gpio/gpio-pisosr.txt

@@ -14,7 +14,7 @@ Optional properties:
  - ngpios		: Number of used GPIO lines (0..n-1), default is 8.
  - load-gpios		: GPIO pin specifier attached to load enable, this
 			  pin is pulsed before reading from the device to
-			  load input pin values into the the device.
+			  load input pin values into the device.
 
 For other required and optional properties of SPI slave
 nodes please refer to ../spi/spi-bus.txt.

Documentation/devicetree/bindings/soc/samsung/exynos-chipid.yaml → Documentation/devicetree/bindings/hwinfo/samsung,exynos-chipid.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: http://devicetree.org/schemas/soc/samsung/exynos-chipid.yaml#
+$id: http://devicetree.org/schemas/hwinfo/samsung,exynos-chipid.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Samsung Exynos SoC series Chipid driver

Documentation/devicetree/bindings/hwinfo/samsung,s5pv210-chipid.yaml

+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwinfo/samsung,s5pv210-chipid.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S5PV210 SoC ChipID
+
+maintainers:
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+properties:
+  compatible:
+    const: samsung,s5pv210-chipid
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    chipid@e0000000 {
+        compatible = "samsung,s5pv210-chipid";
+        reg = <0xe0000000 0x1000>;
+    };

Documentation/devicetree/bindings/soc/ti/k3-socinfo.yaml → Documentation/devicetree/bindings/hwinfo/ti,k3-socinfo.yaml

 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 %YAML 1.2
 ---
-$id: http://devicetree.org/schemas/soc/ti/k3-socinfo.yaml#
+$id: http://devicetree.org/schemas/hwinfo/ti,k3-socinfo.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Texas Instruments K3 Multicore SoC platforms chipid module

Documentation/devicetree/bindings/hwmon/adt7475.yaml

@@ -57,7 +57,7 @@ patternProperties:
       Configures bypassing the individual voltage input attenuator. If
       set to 1 the attenuator is bypassed if set to 0 the attenuator is
       not bypassed. If the property is absent then the attenuator
-      retains it's configuration from the bios/bootloader.
+      retains its configuration from the bios/bootloader.
     $ref: /schemas/types.yaml#/definitions/uint32
     enum: [0, 1]
 

Documentation/devicetree/bindings/i2c/i2c-efm32.txt

-* Energymicro efm32 i2c controller
-
-Required properties :
-
- - reg : Offset and length of the register set for the device
- - compatible : should be "energymicro,efm32-i2c"
- - interrupts : the interrupt number
- - clocks : reference to the module clock
-
-Recommended properties :
-
- - clock-frequency : maximal I2C bus clock frequency in Hz.
- - energymicro,location : Decides the location of the USART I/O pins.
-   Allowed range : [0 .. 6]
-
-Example:
-	i2c0: i2c@4000a000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "energymicro,efm32-i2c";
-		reg = <0x4000a000 0x400>;
-		interrupts = <9>;
-		clocks = <&cmu clk_HFPERCLKI2C0>;
-		clock-frequency = <100000>;
-		energymicro,location = <3>;
-
-		eeprom@50 {
-			compatible = "microchip,24c02";
-			reg = <0x50>;
-			pagesize = <16>;
-		};
-	};
-

Documentation/devicetree/bindings/iio/dac/adi,ad5766.yaml

@@ -22,6 +22,8 @@ properties:
       - adi,ad5767
 
   output-range-microvolts:
+    $ref: /schemas/types.yaml#/definitions/int32-array
+    maxItems: 2
     description: Select converter output range.
 
   reg:

Documentation/devicetree/bindings/input/touchscreen/ektf2127.txt

@@ -6,7 +6,7 @@ Required properties:
  - interrupts		  : interrupt specification for the ektf2127 interrupt
  - power-gpios		  : GPIO specification for the pin connected to the
 			    ektf2127's wake input. This needs to be driven high
-			    to take ektf2127 out of it's low power state
+			    to take ektf2127 out of its low power state
 
 For additional optional properties see: touchscreen.txt
 

Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt

-RDA Micro RDA8810PL Interrupt Controller
-
-The interrupt controller in RDA8810PL SoC is a custom interrupt controller
-which supports up to 32 interrupts.
-
-Required properties:
-
-- compatible: Should be "rda,8810pl-intc".
-- reg: Specifies base physical address of the registers set.
-- interrupt-controller: Identifies the node as an interrupt controller.
-- #interrupt-cells: Specifies the number of cells needed to encode an
-  interrupt source. The value shall be 2.
-
-The interrupt sources are as follows:
-
-ID	Name
-------------
-0:	PULSE_DUMMY
-1:	I2C
-2:	NAND_NFSC
-3:	SDMMC1
-4:	SDMMC2
-5:	SDMMC3
-6:	SPI1
-7:	SPI2
-8:	SPI3
-9:	UART1
-10:	UART2
-11:	UART3
-12:	GPIO1
-13:	GPIO2
-14:	GPIO3
-15:	KEYPAD
-16:	TIMER
-17:	TIMEROS
-18:	COMREG0
-19:	COMREG1
-20:	USB
-21:	DMC
-22:	DMA
-23:	CAMERA
-24:	GOUDA
-25:	GPU
-26:	VPU_JPG
-27:	VPU_HOST
-28:	VOC
-29:	AUIFC0
-30:	AUIFC1
-31:	L2CC
-
-Example:
-		apb@20800000 {
-			compatible = "simple-bus";
-			...
-			intc: interrupt-controller@0 {
-				compatible = "rda,8810pl-intc";
-				reg = <0x0 0x1000>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-		};

Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/rda,8810pl-intc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RDA Micro RDA8810PL interrupt controller
+
+maintainers:
+  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+
+allOf:
+  - $ref: /schemas/interrupt-controller.yaml#
+
+properties:
+  compatible:
+    const: rda,8810pl-intc
+
+  reg:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 2
+
+required:
+  - compatible
+  - reg
+  - interrupt-controller
+  - '#interrupt-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    intc: interrupt-controller@0 {
+      compatible = "rda,8810pl-intc";
+      reg = <0x0 0x1000>;
+      interrupt-controller;
+      #interrupt-cells = <2>;
+    };
+...

Documentation/devicetree/bindings/leds/issi,is31fl319x.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/issi,is31fl319x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ISSI LED controllers bindings for IS31FL319{0,1,3,6,9}
+
+maintainers:
+  - Vincent Knecht <vincent.knecht@mailoo.org>
+
+description: |
+  The IS31FL319X are LED controllers with I2C interface.
+  Previously known as Si-En SN319{0,1,3,6,9}.
+
+  For more product information please see the links below:
+    https://lumissil.com/assets/pdf/core/IS31FL3190_DS.pdf
+    https://lumissil.com/assets/pdf/core/IS31FL3191_DS.pdf
+    https://lumissil.com/assets/pdf/core/IS31FL3193_DS.pdf
+    https://lumissil.com/assets/pdf/core/IS31FL3196_DS.pdf
+    https://lumissil.com/assets/pdf/core/IS31FL3199_DS.pdf
+
+properties:
+  compatible:
+    enum:
+      - issi,is31fl3190
+      - issi,is31fl3191
+      - issi,is31fl3193
+      - issi,is31fl3196
+      - issi,is31fl3199
+      - si-en,sn3190
+      - si-en,sn3191
+      - si-en,sn3193
+      - si-en,sn3196
+      - si-en,sn3199
+
+  reg:
+    maxItems: 1
+
+  shutdown-gpios:
+    maxItems: 1
+    description: GPIO attached to the SDB pin.
+
+  audio-gain-db:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
+    description: Audio gain selection for external analog modulation input.
+    enum: [0, 3, 6, 9, 12, 15, 18, 21]
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+patternProperties:
+  "^led@[1-9]$":
+    type: object
+    $ref: common.yaml#
+
+    properties:
+      reg:
+        description: Index of the LED.
+        minimum: 1
+        maximum: 9
+
+      led-max-microamp:
+        description:
+          Note that a driver will take the lowest of all LED limits
+          since the chip has a single global setting. The lowest value
+          will be chosen due to the PWM specificity, where lower
+          brightness is achieved by reducing the duty-cycle of pulses
+          and not the current, which will always have its peak value
+          equal to led-max-microamp.
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - issi,is31fl3190
+              - issi,is31fl3191
+              - issi,is31fl3193
+              - si-en,sn3190
+              - si-en,sn3191
+              - si-en,sn3193
+    then:
+      properties:
+        reg:
+          enum: [0x68, 0x69, 0x6a, 0x6b]
+
+        audio-gain-db: false
+
+      patternProperties:
+        "^led@[1-9]$":
+          properties:
+            led-max-microamp:
+              default: 42000
+              enum: [5000, 10000, 17500, 30000, 42000]
+    else:
+      properties:
+        reg:
+          enum: [0x64, 0x65, 0x66, 0x67]
+
+      patternProperties:
+        "^led@[1-9]$":
+          properties:
+            led-max-microamp:
+              default: 20000
+              enum: [5000, 10000, 15000, 20000, 25000, 30000, 35000, 40000]
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - issi,is31fl3190
+              - issi,is31fl3191
+              - si-en,sn3190
+              - si-en,sn3191
+    then:
+      patternProperties:
+        "^led@[1-9]$":
+          properties:
+            reg:
+              maximum: 1
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - issi,is31fl3193
+              - si-en,sn3193
+    then:
+      patternProperties:
+        "^led@[1-9]$":
+          properties:
+            reg:
+              maximum: 3
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - issi,is31fl3196
+              - si-en,sn3196
+    then:
+      patternProperties:
+        "^led@[1-9]$":
+          properties:
+            reg:
+              maximum: 6
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/leds/common.h>
+
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        led-controller@65 {
+            compatible = "issi,is31fl3196";
+            reg = <0x65>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            shutdown-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+
+            led@1 {
+                reg = <1>;
+                label = "red:aux";
+                led-max-microamp = <10000>;
+            };
+
+            led@5 {
+                reg = <5>;
+                label = "green:power";
+                linux,default-trigger = "default-on";
+            };
+        };
+    };
+...
+

Documentation/devicetree/bindings/leds/leds-aat1290.txt

-* Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs
-
-The device is controlled through two pins: FL_EN and EN_SET. The pins when,
-asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
-respectively. In order to add a capability of selecting the strobe signal source
-(e.g. CPU or camera sensor) there is an additional switch required, independent
-of the flash chip. The switch is controlled with pin control.
-
-Required properties:
-
-- compatible : Must be "skyworks,aat1290".
-- flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
-- enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
-
-Optional properties:
-- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
-		"default" and "host" must refer to the same pin configuration
-		node, which sets the host as a strobe signal provider. Entry
-		"isp" must refer to the pin configuration node, which sets the
-		ISP as a strobe signal provider.
-
-A discrete LED element connected to the device must be represented by a child
-node - see Documentation/devicetree/bindings/leds/common.txt.
-
-Required properties of the LED child node:
-- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
-- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
-                       Maximum flash LED supply current can be calculated using
-                       following formula: I = 1A * 162kohm / Rset.
-- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
-                         Maximum flash timeout can be calculated using following
-                         formula: T = 8.82 * 10^9 * Ct.
-
-Optional properties of the LED child node:
-- function : see Documentation/devicetree/bindings/leds/common.txt
-- color : see Documentation/devicetree/bindings/leds/common.txt
-- label : see Documentation/devicetree/bindings/leds/common.txt (deprecated)
-
-Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with
-a switch that allows for routing strobe signal either from the host or from
-the camera sensor):
-
-#include "exynos4412.dtsi"
-#include <dt-bindings/leds/common.h>
-
-led-controller {
-	compatible = "skyworks,aat1290";
-	flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
-	enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
-
-	pinctrl-names = "default", "host", "isp";
-	pinctrl-0 = <&camera_flash_host>;
-	pinctrl-1 = <&camera_flash_host>;
-	pinctrl-2 = <&camera_flash_isp>;
-
-	camera_flash: led {
-		function = LED_FUNCTION_FLASH;
-		color = <LED_COLOR_ID_WHITE>;
-		led-max-microamp = <520833>;
-		flash-max-microamp = <1012500>;
-		flash-max-timeout-us = <1940000>;
-	};
-};
-
-&pinctrl_0 {
-	camera_flash_host: camera-flash-host {
-		samsung,pins = "gpj1-0";
-		samsung,pin-function = <1>;
-		samsung,pin-val = <0>;
-	};
-
-	camera_flash_isp: camera-flash-isp {
-		samsung,pins = "gpj1-0";
-		samsung,pin-function = <1>;
-		samsung,pin-val = <1>;
-	};
-};

Documentation/devicetree/bindings/leds/leds-is31fl319x.txt

-LEDs connected to is31fl319x LED controller chip
-
-Required properties:
-- compatible : Should be any of
-	"issi,is31fl3190"
-	"issi,is31fl3191"
-	"issi,is31fl3193"
-	"issi,is31fl3196"
-	"issi,is31fl3199"
-	"si-en,sn3199".
-- #address-cells: Must be 1.
-- #size-cells: Must be 0.
-- reg: 0x64, 0x65, 0x66, or 0x67.
-
-Optional properties:
-- audio-gain-db : audio gain selection for external analog modulation input.
-	Valid values: 0 - 21, step by 3 (rounded down)
-	Default: 0
-- shutdown-gpios : Specifier of the GPIO connected to SDB pin of the chip.
-
-Each led is represented as a sub-node of the issi,is31fl319x device.
-There can be less leds subnodes than the chip can support but not more.
-
-Required led sub-node properties:
-- reg : number of LED line
-	Valid values: 1 - number of leds supported by the chip variant.
-
-Optional led sub-node properties:
-- label : see Documentation/devicetree/bindings/leds/common.txt.
-- linux,default-trigger :
-	see Documentation/devicetree/bindings/leds/common.txt.
-- led-max-microamp : (optional)
-	Valid values: 5000 - 40000, step by 5000 (rounded down)
-	Default: 20000 (20 mA)
-	Note: a driver will take the lowest of all led limits since the
-	chip has a single global setting. The lowest value will be chosen
-	due to the PWM specificity, where lower brightness is achieved
-	by reducing the dury-cycle of pulses and not the current, which
-	will always have its peak value equal to led-max-microamp.
-
-Examples:
-
-fancy_leds: leds@65 {
-	compatible = "issi,is31fl3196";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	reg = <0x65>;
-	shutdown-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
-
-	red_aux: led@1 {
-		label = "red:aux";
-		reg = <1>;
-		led-max-microamp = <10000>;
-	};
-
-	green_power: led@5 {
-		label = "green:power";
-		reg = <5>;
-		linux,default-trigger = "default-on";
-	};
-};

Documentation/devicetree/bindings/leds/leds-lp50xx.yaml

@@ -78,60 +78,66 @@ additionalProperties: false
 
 examples:
   - |
-   #include <dt-bindings/gpio/gpio.h>
-   #include <dt-bindings/leds/common.h>
-
-   i2c {
-       #address-cells = <1>;
-       #size-cells = <0>;
-
-       led-controller@14 {
-           compatible = "ti,lp5009";
-           reg = <0x14>;
-           #address-cells = <1>;
-           #size-cells = <0>;
-           enable-gpios = <&gpio1 16>;
-
-           multi-led@1 {
-               #address-cells = <1>;
-               #size-cells = <0>;
-               reg = <0x1>;
-               color = <LED_COLOR_ID_RGB>;
-               function = LED_FUNCTION_CHARGING;
-
-               led-0 {
-                   color = <LED_COLOR_ID_RED>;
-               };
-
-               led-1 {
-                   color = <LED_COLOR_ID_GREEN>;
-               };
-
-               led-2 {
-                   color = <LED_COLOR_ID_BLUE>;
-               };
-          };
-
-          multi-led@2 {
-            #address-cells = <1>;
-            #size-cells = <2>;
-            reg = <0x2 0x3 0x5>;
-            color = <LED_COLOR_ID_RGB>;
-            function = LED_FUNCTION_STANDBY;
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/leds/common.h>
 
-            led-6 {
-              color = <LED_COLOR_ID_RED>;
-            };
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
 
-            led-7 {
-              color = <LED_COLOR_ID_GREEN>;
+        led-controller@14 {
+            compatible = "ti,lp5009";
+            reg = <0x14>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+            enable-gpios = <&gpio1 16>;
+
+            multi-led@1 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0x1>;
+                color = <LED_COLOR_ID_RGB>;
+                function = LED_FUNCTION_CHARGING;
+
+                led@0 {
+                     reg = <0x0>;
+                     color = <LED_COLOR_ID_RED>;
+                };
+
+                led@1 {
+                     reg = <0x1>;
+                     color = <LED_COLOR_ID_GREEN>;
+                };
+
+                led@2 {
+                     reg = <0x2>;
+                     color = <LED_COLOR_ID_BLUE>;
+                };
             };
 
-            led-8 {
-              color = <LED_COLOR_ID_BLUE>;
+            multi-led@3 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0x3>, <0x4>, <0x5>;
+                color = <LED_COLOR_ID_RGB>;
+                function = LED_FUNCTION_STANDBY;
+
+                led@3 {
+                    reg = <0x3>;
+                    color = <LED_COLOR_ID_RED>;
+                };
+
+                led@4 {
+                    reg = <0x4>;
+                    color = <LED_COLOR_ID_GREEN>;
+                };
+
+                led@5 {
+                    reg = <0x5>;
+                    color = <LED_COLOR_ID_BLUE>;
+                };
             };
-         };
-       };
+        };
     };
 
 ...

Documentation/devicetree/bindings/leds/leds-lp55xx.yaml

@@ -108,119 +108,119 @@ additionalProperties: false
 
 examples:
   - |
-   #include <dt-bindings/leds/common.h>
-
-   i2c {
-       #address-cells = <1>;
-       #size-cells = <0>;
-
-       led-controller@32 {
-           #address-cells = <1>;
-           #size-cells = <0>;
-           compatible = "ti,lp8501";
-           reg = <0x32>;
-           clock-mode = /bits/ 8 <2>;
-           pwr-sel = /bits/ 8 <3>;	/* D1~9 connected to VOUT */
-
-           led@0 {
-               reg = <0>;
-               chan-name = "d1";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
-
-           led@1 {
-               reg = <1>;
-               chan-name = "d2";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
-
-           led@2 {
-               reg = <2>;
-               chan-name = "d3";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
-
-           led@3 {
-               reg = <3>;
-               chan-name = "d4";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
-
-           led@4 {
-               reg = <4>;
-               chan-name = "d5";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
-
-           led@5 {
-               reg = <5>;
-               chan-name = "d6";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
-
-           led@6 {
-               reg = <6>;
-               chan-name = "d7";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
-
-           led@7 {
-               reg = <7>;
-               chan-name = "d8";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
-
-           led@8 {
-               reg = <8>;
-               chan-name = "d9";
-               led-cur = /bits/ 8 <0x14>;
-               max-cur = /bits/ 8 <0x20>;
-           };
+    #include <dt-bindings/leds/common.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        led-controller@32 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            compatible = "ti,lp8501";
+            reg = <0x32>;
+            clock-mode = /bits/ 8 <2>;
+            pwr-sel = /bits/ 8 <3>;	/* D1~9 connected to VOUT */
+
+            led@0 {
+                reg = <0>;
+                chan-name = "d1";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
+
+            led@1 {
+                reg = <1>;
+                chan-name = "d2";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
+
+            led@2 {
+                reg = <2>;
+                chan-name = "d3";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
+
+            led@3 {
+                reg = <3>;
+                chan-name = "d4";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
+
+            led@4 {
+                reg = <4>;
+                chan-name = "d5";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
+
+            led@5 {
+                reg = <5>;
+                chan-name = "d6";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
+
+            led@6 {
+                reg = <6>;
+                chan-name = "d7";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
+
+            led@7 {
+                reg = <7>;
+                chan-name = "d8";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
+
+            led@8 {
+                reg = <8>;
+                chan-name = "d9";
+                led-cur = /bits/ 8 <0x14>;
+                max-cur = /bits/ 8 <0x20>;
+            };
         };
 
-       led-controller@33 {
-           #address-cells = <1>;
-           #size-cells = <0>;
-           compatible = "national,lp5523";
-           reg = <0x33>;
-           clock-mode = /bits/ 8 <0>;
-
-           multi-led@2 {
-               #address-cells = <1>;
-               #size-cells = <0>;
-               reg = <0x2>;
-               color = <LED_COLOR_ID_RGB>;
-               function = LED_FUNCTION_STANDBY;
-               linux,default-trigger = "heartbeat";
-
-               led@0 {
-                   led-cur = /bits/ 8 <50>;
-                   max-cur = /bits/ 8 <100>;
-                   reg = <0x0>;
-                   color = <LED_COLOR_ID_GREEN>;
-               };
-
-               led@1 {
-                   led-cur = /bits/ 8 <50>;
-                   max-cur = /bits/ 8 <100>;
-                   reg = <0x1>;
-                   color = <LED_COLOR_ID_BLUE>;
-               };
-
-               led@6 {
-                   led-cur = /bits/ 8 <50>;
-                   max-cur = /bits/ 8 <100>;
-                   reg = <0x6>;
-                   color = <LED_COLOR_ID_RED>;
-               };
+        led-controller@33 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            compatible = "national,lp5523";
+            reg = <0x33>;
+            clock-mode = /bits/ 8 <0>;
+
+            multi-led@2 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0x2>;
+                color = <LED_COLOR_ID_RGB>;
+                function = LED_FUNCTION_STANDBY;
+                linux,default-trigger = "heartbeat";
+
+                led@0 {
+                    led-cur = /bits/ 8 <50>;
+                    max-cur = /bits/ 8 <100>;
+                    reg = <0x0>;
+                    color = <LED_COLOR_ID_GREEN>;
+                };
+
+                led@1 {
+                    led-cur = /bits/ 8 <50>;
+                    max-cur = /bits/ 8 <100>;
+                    reg = <0x1>;
+                    color = <LED_COLOR_ID_BLUE>;
+                };
+
+                led@6 {
+                    led-cur = /bits/ 8 <50>;
+                    max-cur = /bits/ 8 <100>;
+                    reg = <0x6>;
+                    color = <LED_COLOR_ID_RED>;
+                };
             };
         };
     };

Documentation/devicetree/bindings/leds/leds-pwm-multicolor.yaml

@@ -55,24 +55,24 @@ examples:
         compatible = "pwm-leds-multicolor";
 
         multi-led {
-          color = <LED_COLOR_ID_RGB>;
-          function = LED_FUNCTION_INDICATOR;
-          max-brightness = <65535>;
-
-          led-red {
-              pwms = <&pwm1 0 1000000>;
-              color = <LED_COLOR_ID_RED>;
-          };
-
-          led-green {
-              pwms = <&pwm2 0 1000000>;
-              color = <LED_COLOR_ID_GREEN>;
-          };
-
-          led-blue {
-              pwms = <&pwm3 0 1000000>;
-              color = <LED_COLOR_ID_BLUE>;
-          };
+            color = <LED_COLOR_ID_RGB>;
+            function = LED_FUNCTION_INDICATOR;
+            max-brightness = <65535>;
+
+            led-red {
+                pwms = <&pwm1 0 1000000>;
+                color = <LED_COLOR_ID_RED>;
+            };
+
+            led-green {
+                pwms = <&pwm2 0 1000000>;
+                color = <LED_COLOR_ID_GREEN>;
+            };
+
+            led-blue {
+                pwms = <&pwm3 0 1000000>;
+                color = <LED_COLOR_ID_BLUE>;
+            };
         };
     };
 

Documentation/devicetree/bindings/leds/leds-qcom-lpg.yaml

@@ -17,6 +17,7 @@ description: >
 properties:
   compatible:
     enum:
+      - qcom,pm660l-lpg
       - qcom,pm8150b-lpg
       - qcom,pm8150l-lpg
       - qcom,pm8350c-pwm

Documentation/devicetree/bindings/leds/skyworks,aat1290.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/skyworks,aat1290.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Skyworks Solutions, Inc. AAT1290 Current Regulator for Flash LEDs
+
+maintainers:
+  - Jacek Anaszewski <jacek.anaszewski@gmail.com>
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |
+  The device is controlled through two pins:: FL_EN and EN_SET. The pins when,
+  asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
+  respectively. In order to add a capability of selecting the strobe signal
+  source (e.g. CPU or camera sensor) there is an additional switch required,
+  independent of the flash chip. The switch is controlled with pin control.
+
+properties:
+  compatible:
+    const: skyworks,aat1290
+
+  enset-gpios:
+    maxItems: 1
+    description: EN_SET pin
+
+  flen-gpios:
+    maxItems: 1
+    description: FL_EN pin
+
+  led:
+    $ref: common.yaml#
+    unevaluatedProperties: false
+
+    properties:
+      led-max-microamp: true
+
+      flash-max-microamp:
+        description: |
+          Maximum flash LED supply current can be calculated using following
+          formula:: I = 1A * 162 kOhm / Rset.
+
+      flash-max-timeout-us:
+        description: |
+          Maximum flash timeout can be calculated using following formula::
+            T = 8.82 * 10^9 * Ct.
+
+    required:
+      - flash-max-microamp
+      - flash-max-timeout-us
+      - led-max-microamp
+
+  pinctrl-names:
+    items:
+      - const: default
+      - const: host
+      - const: isp
+
+  pinctrl-0: true
+  pinctrl-1: true
+  pinctrl-2: true
+
+required:
+  - compatible
+  - enset-gpios
+  - flen-gpios
+  - led
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/leds/common.h>
+
+    // Ct = 220 nF, Rset = 160 kOhm
+    led-controller {
+        compatible = "skyworks,aat1290";
+        flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
+        enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
+
+        pinctrl-names = "default", "host", "isp";
+        pinctrl-0 = <&camera_flash_host>;
+        pinctrl-1 = <&camera_flash_host>;
+        pinctrl-2 = <&camera_flash_isp>;
+
+        led {
+            function = LED_FUNCTION_FLASH;
+            color = <LED_COLOR_ID_WHITE>;
+            led-max-microamp = <520833>;
+            flash-max-microamp = <1012500>;
+            flash-max-timeout-us = <1940000>;
+        };
+    };

Documentation/devicetree/bindings/media/gpio-ir-receiver.txt

-Device-Tree bindings for GPIO IR receiver
-
-Required properties:
-	- compatible: should be "gpio-ir-receiver".
-	- gpios: specifies GPIO used for IR signal reception.
-
-Optional properties:
-	- linux,rc-map-name: see rc.txt file in the same
-	  directory.
-	- linux,autosuspend-period: autosuspend delay time,
-	  the unit is milisecond.
-
-Example node:
-
-	ir: ir-receiver {
-		compatible = "gpio-ir-receiver";
-		gpios = <&gpio0 19 1>;
-		linux,rc-map-name = "rc-rc6-mce";
-		linux,autosuspend-period = <125>;
-	};

Documentation/devicetree/bindings/media/gpio-ir-receiver.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/gpio-ir-receiver.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: GPIO Based IR receiver
+
+maintainers:
+  - Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
+
+allOf:
+  - $ref: rc.yaml#
+
+properties:
+  compatible:
+    const: gpio-ir-receiver
+
+  gpios:
+    maxItems: 1
+
+  linux,autosuspend-period:
+    description: autosuspend delay time in milliseconds
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+required:
+  - compatible
+  - gpios
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    ir-receiver {
+        compatible = "gpio-ir-receiver";
+        gpios = <&gpio0 19 1>;
+        linux,rc-map-name = "rc-rc6-mce";
+        linux,autosuspend-period = <125>;
+    };
+...

Documentation/devicetree/bindings/media/rc.yaml

@@ -12,7 +12,7 @@ maintainers:
 
 properties:
   $nodename:
-    pattern: "^ir(@[a-f0-9]+)?$"
+    pattern: "^ir(-receiver)?(@[a-f0-9]+)?$"
 
   linux,rc-map-name:
     description:

Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml

@@ -74,7 +74,7 @@ properties:
   rohm,enable-hidden-gpo:
     description: |
       The BD71815 has undocumented GPO at pin E5. Pin is marked as GND at the
-      data-sheet as it's location in the middle of GND pins makes it hard to
+      data-sheet as its location in the middle of GND pins makes it hard to
       use on PCB. If your board has managed to use this pin you can enable the
       second GPO by defining this property. Dont enable this if you are unsure
       about how the E5 pin is connected on your board.

Documentation/devicetree/bindings/mips/lantiq/rcu.txt

@@ -2,7 +2,7 @@ Lantiq XWAY SoC RCU binding
 ===========================
 
 This binding describes the RCU (reset controller unit) multifunction device,
-where each sub-device has it's own set of registers.
+where each sub-device has its own set of registers.
 
 The RCU register range is used for multiple purposes. Mostly one device
 uses one or multiple register exclusively, but for some registers some

Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml

@@ -22,13 +22,14 @@ properties:
   reg:
     maxItems: 1
 
-  spi-max-frequency: true
-
 required:
   - compatible
   - reg
 
-additionalProperties: false
+allOf:
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+unevaluatedProperties: false
 
 examples:
   - |

Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.txt

-ARM AFS - ARM Firmware Suite Partitions
-=======================================
-
-The ARM Firmware Suite is a flash partitioning system found on the
-ARM reference designs: Integrator AP, Integrator CP, Versatile AB,
-Versatile PB, the RealView family, Versatile Express and Juno.
-
-Required properties:
-- compatible : (required) must be "arm,arm-firmware-suite"
-
-Example:
-
-flash@0 {
-	partitions {
-		compatible = "arm,arm-firmware-suite";
-	};
-};

Documentation/devicetree/bindings/mtd/partitions/arm,arm-firmware-suite.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/partitions/arm,arm-firmware-suite.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ARM Firmware Suite (AFS) Partitions
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+description: |
+  The ARM Firmware Suite is a flash partitioning system found on the
+  ARM reference designs: Integrator AP, Integrator CP, Versatile AB,
+  Versatile PB, the RealView family, Versatile Express and Juno.
+
+properties:
+  compatible:
+    const: arm,arm-firmware-suite
+
+additionalProperties: false
+
+examples:
+  - |
+    partitions {
+        compatible = "arm,arm-firmware-suite";
+    };
+...

Documentation/devicetree/bindings/net/altera_tse.txt

@@ -15,7 +15,7 @@ Required properties:
   "rx_desc":      MSGDMA Rx dispatcher descriptor space region
   "rx_resp":      MSGDMA Rx dispatcher response space region
   "s1":		  SGDMA descriptor memory
-- interrupts: Should contain the TSE interrupts and it's mode.
+- interrupts: Should contain the TSE interrupts and its mode.
 - interrupt-names: Should contain the interrupt names
   "rx_irq":       xDMA Rx dispatcher interrupt
   "tx_irq":       xDMA Tx dispatcher interrupt

Documentation/devicetree/bindings/net/cpsw.txt

@@ -20,7 +20,7 @@ Required properties:
 - active_slave		: Specifies the slave to use for time stamping,
 			  ethtool and SIOCGMIIPHY
 - cpsw-phy-sel		: Specifies the phandle to the CPSW phy mode selection
-			  device. See also cpsw-phy-sel.txt for it's binding.
+			  device. See also cpsw-phy-sel.txt for its binding.
 			  Note that in legacy cases cpsw-phy-sel may be
 			  a child device instead of a phandle
 			  (DEPRECATED, use phys property instead).

Documentation/devicetree/bindings/net/emac_rockchip.txt

-* ARC EMAC 10/100 Ethernet platform driver for Rockchip RK3036/RK3066/RK3188 SoCs
-
-Required properties:
-- compatible: should be "rockchip,<name>-emac"
-   "rockchip,rk3036-emac": found on RK3036 SoCs
-   "rockchip,rk3066-emac": found on RK3066 SoCs
-   "rockchip,rk3188-emac": found on RK3188 SoCs
-- reg: Address and length of the register set for the device
-- interrupts: Should contain the EMAC interrupts
-- rockchip,grf: phandle to the syscon grf used to control speed and mode
-  for emac.
-- phy: see ethernet.txt file in the same directory.
-- phy-mode: see ethernet.txt file in the same directory.
-
-Optional properties:
-- phy-supply: phandle to a regulator if the PHY needs one
-
-Clock handling:
-- clocks: Must contain an entry for each entry in clock-names.
-- clock-names: Shall be "hclk" for the host clock needed to calculate and set
-  polling period of EMAC and "macref" for the reference clock needed to transfer
-  data to and from the phy.
-
-Child nodes of the driver are the individual PHY devices connected to the
-MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus.
-
-Examples:
-
-ethernet@10204000 {
-	compatible = "rockchip,rk3188-emac";
-	reg = <0xc0fc2000 0x3c>;
-	interrupts = <6>;
-	mac-address = [ 00 11 22 33 44 55 ];
-
-	clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>;
-	clock-names = "hclk", "macref";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
-
-	rockchip,grf = <&grf>;
-
-	phy = <&phy0>;
-	phy-mode = "rmii";
-	phy-supply = <&vcc_rmii>;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-	phy0: ethernet-phy@0 {
-	      reg = <1>;
-	};
-};

Documentation/devicetree/bindings/net/nfc/nxp,nci.yaml

@@ -7,7 +7,6 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: NXP Semiconductors NCI NFC controller
 
 maintainers:
-  - Charles Gorand <charles.gorand@effinnov.com>
   - Krzysztof Kozlowski <krzk@kernel.org>
 
 properties:

Documentation/devicetree/bindings/net/qcom-emac.txt

@@ -14,7 +14,7 @@ MAC node:
 - mac-address : The 6-byte MAC address. If present, it is the default
 	MAC address.
 - internal-phy : phandle to the internal PHY node
-- phy-handle : phandle the the external PHY node
+- phy-handle : phandle the external PHY node
 
 Internal PHY node:
 - compatible : Should be "qcom,fsm9900-emac-sgmii" or "qcom,qdf2432-emac-sgmii".

Documentation/devicetree/bindings/net/rockchip,emac.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/rockchip,emac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip RK3036/RK3066/RK3188 Ethernet Media Access Controller (EMAC)
+
+maintainers:
+  - Heiko Stuebner <heiko@sntech.de>
+
+properties:
+  compatible:
+    enum:
+      - rockchip,rk3036-emac
+      - rockchip,rk3066-emac
+      - rockchip,rk3188-emac
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 2
+    items:
+      - description: host clock
+      - description: reference clock
+      - description: mac TX/RX clock
+
+  clock-names:
+    minItems: 2
+    items:
+      - const: hclk
+      - const: macref
+      - const: macclk
+
+  rockchip,grf:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to the syscon GRF used to control speed and mode for the EMAC.
+
+  phy-supply:
+    description:
+      Phandle to a regulator if the PHY needs one.
+
+  mdio:
+    $ref: mdio.yaml#
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - rockchip,grf
+  - phy
+  - phy-mode
+  - mdio
+
+allOf:
+  - $ref: "ethernet-controller.yaml#"
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: rockchip,rk3036-emac
+
+    then:
+      properties:
+        clocks:
+          minItems: 3
+
+        clock-names:
+          minItems: 3
+
+    else:
+      properties:
+        clocks:
+          maxItems: 2
+
+        clock-names:
+          maxItems: 2
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/rk3188-cru-common.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    ethernet@10204000 {
+      compatible = "rockchip,rk3188-emac";
+      reg = <0xc0fc2000 0x3c>;
+      interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+      clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>;
+      clock-names = "hclk", "macref";
+      rockchip,grf = <&grf>;
+      pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
+      pinctrl-names = "default";
+      phy = <&phy0>;
+      phy-mode = "rmii";
+      phy-supply = <&vcc_rmii>;
+
+      mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        phy0: ethernet-phy@0 {
+          reg = <1>;
+        };
+      };
+    };

Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml

@@ -144,6 +144,7 @@ properties:
     description: If present then the reset sequence using the GPIO
       specified in the "reset-gpio" property is reversed (H=reset state,
       L=operation state) (optional required).
+    type: boolean
 
   vpcie-supply:
     description: Should specify the regulator in charge of PCIe port power.

Documentation/devicetree/bindings/pci/host-generic-pci.yaml

@@ -106,6 +106,9 @@ properties:
     maxItems: 3
 
   dma-coherent: true
+  iommu-map: true
+  iommu-map-mask: true
+  msi-parent: true
 
 required:
   - compatible

Documentation/devicetree/bindings/perf/arm,ccn.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/perf/arm,ccn.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ARM CCN (Cache Coherent Network) Performance Monitors
+
+maintainers:
+  - Robin Murphy <robin.murphy@arm.com>
+
+properties:
+  compatible:
+    enum:
+      - arm,ccn-502
+      - arm,ccn-504
+      - arm,ccn-508
+      - arm,ccn-512
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    ccn@20000000 {
+        compatible = "arm,ccn-504";
+        reg = <0x20000000 0x1000000>;
+        interrupts = <0 181 4>;
+    };
+...

Documentation/devicetree/bindings/perf/arm-ccn.txt

-* ARM CCN (Cache Coherent Network)
-
-Required properties:
-
-- compatible: (standard compatible string) should be one of:
-	"arm,ccn-502"
-	"arm,ccn-504"
-	"arm,ccn-508"
-	"arm,ccn-512"
-
-- reg: (standard registers property) physical address and size
-	(16MB) of the configuration registers block
-
-- interrupts: (standard interrupt property) single interrupt
-	generated by the control block
-
-Example:
-
-	ccn@2000000000 {
-		compatible = "arm,ccn-504";
-		reg = <0x20 0x00000000 0 0x1000000>;
-		interrupts = <0 181 4>;
-	};

Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml

@@ -16,7 +16,7 @@ description: |+
   - compatible: Should be the following:
                 "amlogic,meson-gx-hhi-sysctrl", "simple-mfd", "syscon"
 
-  Refer to the the bindings described in
+  Refer to the bindings described in
   Documentation/devicetree/bindings/mfd/syscon.yaml
 
 properties:

Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml

@@ -16,7 +16,7 @@ description: |+
   - compatible:     Should be one of the following:
                     "aspeed,ast2400-scu", "syscon", "simple-mfd"
 
-  Refer to the the bindings described in
+  Refer to the bindings described in
   Documentation/devicetree/bindings/mfd/syscon.yaml
 
 properties:

Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml

@@ -17,7 +17,7 @@ description: |+
   			"aspeed,ast2500-scu", "syscon", "simple-mfd"
   			"aspeed,g5-scu", "syscon", "simple-mfd"
 
-  Refer to the the bindings described in
+  Refer to the bindings described in
   Documentation/devicetree/bindings/mfd/syscon.yaml
 
 properties:

Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml

@@ -16,7 +16,7 @@ description: |+
   - compatible: Should be one of the following:
                 "aspeed,ast2600-scu", "syscon", "simple-mfd"
 
-  Refer to the the bindings described in
+  Refer to the bindings described in
   Documentation/devicetree/bindings/mfd/syscon.yaml
 
 properties:

Documentation/devicetree/bindings/power/amlogic,meson-ee-pwrc.yaml

@@ -2,8 +2,8 @@
 # Copyright 2019 BayLibre, SAS
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/amlogic,meson-ee-pwrc.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/amlogic,meson-ee-pwrc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Amlogic Meson Everything-Else Power Domains
 
@@ -17,7 +17,7 @@ description: |+
   - compatible: Should be the following:
                 "amlogic,meson-gx-hhi-sysctrl", "simple-mfd", "syscon"
 
-  Refer to the the bindings described in
+  Refer to the bindings described in
   Documentation/devicetree/bindings/mfd/syscon.yaml
 
 properties:

Documentation/devicetree/bindings/power/amlogic,meson-sec-pwrc.yaml

@@ -3,8 +3,8 @@
 # Author: Jianxin Pan <jianxin.pan@amlogic.com>
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/amlogic,meson-sec-pwrc.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/amlogic,meson-sec-pwrc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Amlogic Meson Secure Power Domains
 

Documentation/devicetree/bindings/power/apple,pmgr-pwrstate.yaml

@@ -10,7 +10,7 @@ maintainers:
   - Hector Martin <marcan@marcan.st>
 
 allOf:
-  - $ref: "power-domain.yaml#"
+  - $ref: power-domain.yaml#
 
 description: |
   Apple SoCs include PMGR blocks responsible for power management,

Documentation/devicetree/bindings/power/brcm,bcm63xx-power.yaml

 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/brcm,bcm63xx-power.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/brcm,bcm63xx-power.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: BCM63xx power domain driver
 

Documentation/devicetree/bindings/power/renesas,apmu.yaml

 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/renesas,apmu.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/renesas,apmu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Renesas Advanced Power Management Unit
 

Documentation/devicetree/bindings/power/renesas,rcar-sysc.yaml

 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/renesas,rcar-sysc.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/renesas,rcar-sysc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Renesas R-Car and RZ/G System Controller
 

Documentation/devicetree/bindings/power/reset/qcom,pon.yaml

@@ -30,11 +30,15 @@ properties:
 
   pwrkey:
     type: object
-    $ref: "../../input/qcom,pm8941-pwrkey.yaml#"
+    $ref: /schemas/input/qcom,pm8941-pwrkey.yaml#
 
   resin:
     type: object
-    $ref: "../../input/qcom,pm8941-pwrkey.yaml#"
+    $ref: /schemas/input/qcom,pm8941-pwrkey.yaml#
+
+  watchdog:
+    type: object
+    $ref: /schemas/watchdog/qcom,pm8916-wdt.yaml
 
 required:
   - compatible

Documentation/devicetree/bindings/power/reset/regulator-poweroff.yaml

@@ -16,7 +16,7 @@ description: |
 
 properties:
   compatible:
-    const: "regulator-poweroff"
+    const: regulator-poweroff
 
   cpu-supply:
     description:

Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.yaml

@@ -15,7 +15,7 @@ description: |
 
 properties:
   compatible:
-    const: "xlnx,zynqmp-power"
+    const: xlnx,zynqmp-power
 
   interrupts:
     maxItems: 1

Documentation/devicetree/bindings/power/supply/active-semi,act8945a-charger.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/active-semi,act8945a-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/active-semi,act8945a-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Active-semi ACT8945A Charger Function
 

Documentation/devicetree/bindings/power/supply/bq2415x.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq2415x.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq2415x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Binding for TI bq2415x Li-Ion Charger
 

Documentation/devicetree/bindings/power/supply/bq24190.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq24190.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq24190.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Binding for TI BQ2419x Li-Ion Battery Charger
 

Documentation/devicetree/bindings/power/supply/bq24257.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq24257.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq24257.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Binding for bq24250, bq24251 and bq24257 Li-Ion Charger
 

Documentation/devicetree/bindings/power/supply/bq24735.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq24735.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq24735.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Binding for TI BQ24735 Li-Ion Battery Charger
 

Documentation/devicetree/bindings/power/supply/bq2515x.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2020 Texas Instruments Incorporated
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq2515x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: TI bq2515x 500-mA Linear charger family
 

Documentation/devicetree/bindings/power/supply/bq256xx.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2020 Texas Instruments Incorporated
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq256xx.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq256xx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: TI bq256xx Switch Mode Buck Charger
 

Documentation/devicetree/bindings/power/supply/bq25890.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq25890.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq25890.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Binding for bq25890, bq25892, bq25895 and bq25896 Li-Ion Charger
 

Documentation/devicetree/bindings/power/supply/bq25980.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2020 Texas Instruments Incorporated
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq25980.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq25980.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: TI BQ25980 Flash Charger
 

Documentation/devicetree/bindings/power/supply/bq27xxx.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2020 Texas Instruments Incorporated
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/bq27xxx.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/bq27xxx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: TI BQ27XXX fuel gauge family
 

Documentation/devicetree/bindings/power/supply/charger-manager.yaml

@@ -50,6 +50,7 @@ properties:
 
   cm-battery-stat:
     description: battery status
+    $ref: /schemas/types.yaml#/definitions/uint32
     enum:
       - 0 # battery always present
       - 1 # no battery

Documentation/devicetree/bindings/power/supply/cpcap-battery.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/cpcap-battery.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/cpcap-battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Motorola CPCAP PMIC battery
 

Documentation/devicetree/bindings/power/supply/cpcap-charger.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/cpcap-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/cpcap-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Motorola CPCAP PMIC charger
 

Documentation/devicetree/bindings/power/supply/dlg,da9150-charger.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/dlg,da9150-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/dlg,da9150-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Dialog Semiconductor DA9150 Charger Power Supply bindings
 

Documentation/devicetree/bindings/power/supply/dlg,da9150-fuel-gauge.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/dlg,da9150-fuel-gauge.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/dlg,da9150-fuel-gauge.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings
 

Documentation/devicetree/bindings/power/supply/ingenic,battery.yaml

@@ -2,8 +2,8 @@
 # Copyright 2019-2020 Artur Rojek
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/ingenic,battery.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/ingenic,battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Ingenic JZ47xx battery bindings
 

Documentation/devicetree/bindings/power/supply/isp1704.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/isp1704.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/isp1704.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Binding for NXP ISP1704 USB Charger Detection
 

Documentation/devicetree/bindings/power/supply/lego,ev3-battery.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/lego,ev3-battery.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/lego,ev3-battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: LEGO MINDSTORMS EV3 Battery
 

Documentation/devicetree/bindings/power/supply/lltc,lt3651-charger.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/lltc,lt3651-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/lltc,lt3651-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Analog Devices LT3651 Charger Power Supply bindings
 

Documentation/devicetree/bindings/power/supply/lltc,ltc294x.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/lltc,ltc294x.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/lltc,ltc294x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery fuel gauges
 

Documentation/devicetree/bindings/power/supply/ltc4162-l.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2020 Topic Embedded Products
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/ltc4162-l.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/ltc4162-l.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Linear Technology (Analog Devices) LTC4162-L Charger
 

Documentation/devicetree/bindings/power/supply/maxim,ds2760.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/maxim,ds2760.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/maxim,ds2760.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Maxim DS2760 DT bindings
 

Documentation/devicetree/bindings/power/supply/maxim,max14656.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/maxim,max14656.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/maxim,max14656.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Maxim MAX14656 DT bindings
 

Documentation/devicetree/bindings/power/supply/maxim,max17040.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/maxim,max17040.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/maxim,max17040.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Maxim 17040 fuel gauge series
 

Documentation/devicetree/bindings/power/supply/maxim,max17042.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/maxim,max17042.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/maxim,max17042.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Maxim 17042 fuel gauge series
 

Documentation/devicetree/bindings/power/supply/maxim,max8903.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/maxim,max8903.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/maxim,max8903.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Maxim Semiconductor MAX8903 Battery Charger
 

Documentation/devicetree/bindings/power/supply/nokia,n900-battery.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/nokia,n900-battery.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/nokia,n900-battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Nokia N900 battery
 

Documentation/devicetree/bindings/power/supply/olpc-battery.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/olpc-battery.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/olpc-battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: OLPC Battery
 

Documentation/devicetree/bindings/power/supply/power-supply.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/power-supply.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/power-supply.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Power Supply Core Support
 

Documentation/devicetree/bindings/power/supply/richtek,rt5033-battery.yaml

 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/richtek,rt5033-battery.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/richtek,rt5033-battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Richtek RT5033 PMIC Fuel Gauge
 

Documentation/devicetree/bindings/power/supply/richtek,rt9455.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/richtek,rt9455.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/richtek,rt9455.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Binding for Richtek rt9455 battery charger
 

Documentation/devicetree/bindings/power/supply/sc2731-charger.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/sc2731-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/sc2731-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Spreadtrum SC2731 PMICs battery charger binding
 

Documentation/devicetree/bindings/power/supply/sc27xx-fg.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/sc27xx-fg.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/sc27xx-fg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Spreadtrum SC27XX PMICs Fuel Gauge Unit Power Supply Bindings
 

Documentation/devicetree/bindings/power/supply/stericsson,ab8500-btemp.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-btemp.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/stericsson,ab8500-btemp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: AB8500 Battery Temperature Monitor
 

Documentation/devicetree/bindings/power/supply/stericsson,ab8500-chargalg.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-chargalg.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/stericsson,ab8500-chargalg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: AB8500 Charging Algorithm
 

Documentation/devicetree/bindings/power/supply/stericsson,ab8500-charger.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/stericsson,ab8500-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: AB8500 Charger
 

Documentation/devicetree/bindings/power/supply/stericsson,ab8500-fg.yaml

@@ -2,8 +2,8 @@
 # Copyright (C) 2021 Sebastian Reichel
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/stericsson,ab8500-fg.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/stericsson,ab8500-fg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: AB8500 Fuel Gauge
 

Documentation/devicetree/bindings/power/supply/summit,smb347-charger.yaml

 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/summit,smb347-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/summit,smb347-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: Battery charger driver for SMB345, SMB347 and SMB358
 

Documentation/devicetree/bindings/power/supply/tps65090-charger.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/tps65090-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/tps65090-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: TPS65090 Frontend PMU with Switchmode Charger
 

Documentation/devicetree/bindings/power/supply/tps65217-charger.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/tps65217-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/tps65217-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: TPS65217 Charger
 

Documentation/devicetree/bindings/power/supply/twl4030-charger.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/twl4030-charger.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/twl4030-charger.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: TWL4030 BCI (Battery Charger Interface)
 

Documentation/devicetree/bindings/power/supply/x-powers,axp20x-ac-power-supply.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-ac-power-supply.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/x-powers,axp20x-ac-power-supply.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: AXP20x AC power-supply
 

Documentation/devicetree/bindings/power/supply/x-powers,axp20x-battery-power-supply.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-battery-power-supply.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/x-powers,axp20x-battery-power-supply.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: AXP20x Battery power-supply
 

Documentation/devicetree/bindings/power/supply/x-powers,axp20x-usb-power-supply.yaml

 # SPDX-License-Identifier: GPL-2.0
 %YAML 1.2
 ---
-$id: "http://devicetree.org/schemas/power/supply/x-powers,axp20x-usb-power-supply.yaml#"
-$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+$id: http://devicetree.org/schemas/power/supply/x-powers,axp20x-usb-power-supply.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
 
 title: AXP20x USB power-supply
 

Documentation/devicetree/bindings/powerpc/fsl/cpus.txt

@@ -5,7 +5,7 @@ Copyright 2013 Freescale Semiconductor Inc.
 Power Architecture CPUs in Freescale SOCs are represented in device trees as
 per the definition in the Devicetree Specification.
 
-In addition to the the Devicetree Specification definitions, the properties
+In addition to the Devicetree Specification definitions, the properties
 defined below may be present on CPU nodes.
 
 PROPERTIES

Documentation/devicetree/bindings/powerpc/fsl/mpc5200.txt

@@ -172,7 +172,7 @@ Interrupt controller (fsl,mpc5200-pic) node
 The mpc5200 pic binding splits hardware IRQ numbers into two levels.  The
 split reflects the layout of the PIC hardware itself, which groups
 interrupts into one of three groups; CRIT, MAIN or PERP.  Also, the
-Bestcomm dma engine has it's own set of interrupt sources which are
+Bestcomm dma engine has its own set of interrupt sources which are
 cascaded off of peripheral interrupt 0, which the driver interprets as a
 fourth group, SDMA.
 

Documentation/devicetree/bindings/powerpc/opal/power-mgt.txt

@@ -39,7 +39,7 @@ otherwise. The length of all the property arrays must be the same.
 
 - ibm,cpu-idle-state-flags:
 	Array of unsigned 32-bit values containing the values of the
-	flags associated with the the aforementioned idle-states. The
+	flags associated with the aforementioned idle-states. The
 	flag bits are as follows:
 		0x00000001 /* Decrementer would stop */
 		0x00000002 /* Needs timebase restore */

Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt

@@ -37,7 +37,7 @@ on the Qualcomm Hexagon core.
 - interrupt-names:
 	Usage: required
 	Value type: <stringlist>
-	Definition: The interrupts needed depends on the the compatible
+	Definition: The interrupts needed depends on the compatible
 		    string:
 	qcom,q6v5-pil:
 	qcom,ipq8074-wcss-pil:

Documentation/devicetree/bindings/rtc/rtc-ds1307.txt

-Dallas DS1307 and compatible RTC
-
-Required properties:
-- compatible: should be one of:
-	"dallas,ds1307",
-	"dallas,ds1308",
-	"dallas,ds1337",
-	"dallas,ds1338",
-	"dallas,ds1339",
-	"dallas,ds1388",
-	"dallas,ds1340",
-	"dallas,ds1341",
-	"maxim,ds3231",
-	"st,m41t0",
-	"st,m41t00",
-	"st,m41t11",
-	"microchip,mcp7940x",
-	"microchip,mcp7941x",
-	"pericom,pt7c4338",
-	"epson,rx8025",
-	"isil,isl12057"
-	"epson,rx8130"
-- reg: I2C bus address of the device
-
-Optional properties:
-- interrupts: rtc alarm interrupt.
-- clock-output-names: From common clock binding to override the default output
-                      clock name
-- wakeup-source: Enables wake up of host system on alarm
-- trickle-resistor-ohms : ds1339, ds1340 and ds 1388 only
-	Selected resistor for trickle charger
-	Possible values are 250, 2000, 4000
-	Should be given if trickle charger should be enabled
-- aux-voltage-chargeable: ds1339, ds1340, ds1388 and rx8130 only
-	Tells whether the battery/supercap of the RTC (if any) is
-	chargeable or not.
-	Possible values are 0 (not chargeable), 1 (chargeable)
-
-Deprecated properties:
-- trickle-diode-disable : ds1339, ds1340 and ds1388 only
-	Do not use internal trickle charger diode
-	Should be given if internal trickle charger diode should be disabled
-	(superseded by aux-voltage-chargeable)
-
-Example:
-	ds1339: rtc@68 {
-		compatible = "dallas,ds1339";
-		reg = <0x68>;
-		interrupt-parent = <&gpio4>;
-		interrupts = <20 0>;
-		trickle-resistor-ohms = <250>;
-	};

Documentation/devicetree/bindings/rtc/rtc-ds1307.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rtc/rtc-ds1307.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Dallas DS1307 and compatible RTC
+
+maintainers:
+  - Alexandre Belloni <alexandre.belloni@bootlin.com>
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - dallas,ds1307
+          - dallas,ds1308
+          - dallas,ds1337
+          - dallas,ds1338
+          - dallas,ds1339
+          - dallas,ds1388
+          - dallas,ds1340
+          - dallas,ds1341
+          - maxim,ds3231
+          - st,m41t0
+          - st,m41t00
+          - st,m41t11
+          - microchip,mcp7940x
+          - microchip,mcp7941x
+          - pericom,pt7c4338
+          - epson,rx8025
+          - isil,isl12057
+          - epson,rx8130
+
+      - items:
+          - enum:
+              - st,m41t00
+          - const: dallas,ds1338
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    minItems: 1
+    maxItems: 2
+
+  interrupt-names:
+    maxItems: 2
+
+  "#clock-cells":
+    const: 1
+
+  clock-output-names:
+    description: From common clock binding to override the default output clock name.
+
+  wakeup-source:
+    description: Enables wake up of host system on alarm.
+
+  vcc-supply: true
+
+allOf:
+  - $ref: rtc.yaml
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - dallas,ds1339
+              - dallas,ds1340
+              - dallas,ds1388
+    then:
+      properties:
+        trickle-resistor-ohms:
+          description: Selected resistor for trickle charger. Should be specified if trickle
+            charger should be enabled.
+          enum: [ 250, 2000, 4000 ]
+
+        trickle-diode-disable:
+          description: Do not use internal trickle charger diode. Should be given if internal
+            trickle charger diode should be disabled (superseded by aux-voltage-chargeable)
+          deprecated: true
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      rtc@68 {
+        compatible = "dallas,ds1337";
+        reg = <0x68>;
+        interrupt-parent = <&gpio4>;
+        interrupts = <20 0>;
+        trickle-resistor-ohms = <250>;
+      };
+    };

Documentation/devicetree/bindings/rtc/trivial-rtc.yaml

@@ -30,6 +30,8 @@ properties:
       - dallas,ds1672
       # Extremely Accurate I²C RTC with Integrated Crystal and SRAM
       - dallas,ds3232
+      # EM Microelectronic EM3027 RTC
+      - emmicro,em3027
       # I2C-BUS INTERFACE REAL TIME CLOCK MODULE
       - epson,rx8010
       # I2C-BUS INTERFACE REAL TIME CLOCK MODULE

Documentation/devicetree/bindings/serial/efm32-uart.txt

-* Energymicro efm32 UART
-
-Required properties:
-- compatible : Should be "energymicro,efm32-uart"
-- reg : Address and length of the register set
-- interrupts : Should contain uart interrupt
-
-Optional properties:
-- energymicro,location : Decides the location of the USART I/O pins.
-  Allowed range : [0 .. 5]
-  Default: 0
-
-Example:
-
-uart@4000c400 {
-	compatible = "energymicro,efm32-uart";
-	reg = <0x4000c400 0x400>;
-	interrupts = <15>;
-	energymicro,location = <0>;
-};

Documentation/devicetree/bindings/serio/ps2-gpio.txt

-Device-Tree binding for ps/2 gpio device
-
-Required properties:
-	- compatible = "ps2-gpio"
-	- data-gpios: the data pin
-	- clk-gpios: the clock pin
-	- interrupts: Should trigger on the falling edge of the clock line.
-
-Optional properties:
-	- write-enable: Indicates whether write function is provided
-	to serio device. Possibly providing the write fn will not work, because
-	of the tough timing requirements.
-
-Example nodes:
-
-ps2@0 {
-	compatible = "ps2-gpio";
-	interrupt-parent = <&gpio>;
-	interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
-	data-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
-	clk-gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
-	write-enable;
-};

Documentation/devicetree/bindings/serio/ps2-gpio.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serio/ps2-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bindings for GPIO based PS/2
+
+maintainers:
+  - Danilo Krummrich <danilokrummrich@dk-develop.de>
+
+properties:
+  compatible:
+    const: ps2-gpio
+
+  data-gpios:
+    description:
+      the gpio used for the data signal - this should be flagged as
+      active high using open drain with (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)
+      from <dt-bindings/gpio/gpio.h> since the signal is open drain by
+      definition
+    maxItems: 1
+
+  clk-gpios:
+    description:
+      the gpio used for the clock signal - this should be flagged as
+      active high using open drain with (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)
+      from <dt-bindings/gpio/gpio.h> since the signal is open drain by
+      definition
+    maxItems: 1
+
+  interrupts:
+    description:
+      The given interrupt should trigger on the falling edge of the clock line.
+    maxItems: 1
+
+  write-enable:
+    type: boolean
+    description:
+      Indicates whether write function is provided to serio device. Possibly
+      providing the write function will not work, because of the tough timing
+      requirements.
+
+required:
+  - compatible
+  - data-gpios
+  - clk-gpios
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    ps2 {
+        compatible = "ps2-gpio";
+        interrupt-parent = <&gpio>;
+        interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+        data-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+        clk-gpios = <&gpio 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+        write-enable;
+    };

Documentation/devicetree/bindings/soc/qcom/qcom,aoss-qmp.yaml

@@ -13,7 +13,7 @@ description:
   This binding describes the hardware component responsible for side channel
   requests to the always-on subsystem (AOSS), used for certain power management
   requests that is not handled by the standard RPMh interface. Each client in the
-  SoC has it's own block of message RAM and IRQ for communication with the AOSS.
+  SoC has its own block of message RAM and IRQ for communication with the AOSS.
   The protocol used to communicate in the message RAM is known as Qualcomm
   Messaging Protocol (QMP)
 

Documentation/devicetree/bindings/sound/da9055.txt

@@ -2,7 +2,7 @@
 
 DA9055 provides Audio CODEC support (I2C only).
 
-The Audio CODEC device in DA9055 has it's own I2C address which is configurable,
+The Audio CODEC device in DA9055 has its own I2C address which is configurable,
 so the device is instantiated separately from the PMIC (MFD) device.
 
 For details on accompanying PMIC I2C device, see the following:

Documentation/devicetree/bindings/sound/tlv320adcx140.yaml

@@ -68,9 +68,9 @@ properties:
        array is defined as <PDMIN1 PDMIN2 PDMIN3 PDMIN4>.
 
        0 - (default) Odd channel is latched on the negative edge and even
-       channel is latched on the the positive edge.
+       channel is latched on the positive edge.
        1 - Odd channel is latched on the positive edge and even channel is
-       latched on the the negative edge.
+       latched on the negative edge.
 
        PDMIN1 - PDMCLK latching edge used for channel 1 and 2 data
        PDMIN2 - PDMCLK latching edge used for channel 3 and 4 data

Documentation/devicetree/bindings/spi/efm32-spi.txt

-* Energy Micro EFM32 SPI
-
-Required properties:
-- #address-cells: see spi-bus.txt
-- #size-cells: see spi-bus.txt
-- compatible: should be "energymicro,efm32-spi"
-- reg: Offset and length of the register set for the controller
-- interrupts: pair specifying rx and tx irq
-- clocks: phandle to the spi clock
-- cs-gpios: see spi-bus.txt
-
-Recommended properties :
-- energymicro,location: Value to write to the ROUTE register's LOCATION
-                        bitfield to configure the pinmux for the device, see
-                        datasheet for values.
-                        If this property is not provided, keeping what is
-                        already configured in the hardware, so its either the
-                        reset default 0 or whatever the bootloader did.
-
-Example:
-
-spi1: spi@4000c400 { /* USART1 */
-	#address-cells = <1>;
-	#size-cells = <0>;
-	compatible = "energymicro,efm32-spi";
-	reg = <0x4000c400 0x400>;
-	interrupts = <15 16>;
-	clocks = <&cmu 20>;
-	cs-gpios = <&gpio 51 1>; // D3
-	energymicro,location = <1>;
-
-	ks8851@0 {
-		compatible = "ks8851";
-		spi-max-frequency = <6000000>;
-		reg = <0>;
-		interrupt-parent = <&boardfpga>;
-		interrupts = <4>;
-	};
-};

Documentation/devicetree/bindings/sram/qcom,imem.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sram/qcom,imem.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm IMEM memory region
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description:
+  Qualcomm IMEM is dedicated memory region for various debug features and DMA
+  transactions.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - qcom,apq8064-imem
+          - qcom,msm8974-imem
+          - qcom,qcs404-imem
+          - qcom,sc7180-imem
+          - qcom,sc7280-imem
+          - qcom,sdm630-imem
+          - qcom,sdm845-imem
+          - qcom,sdx55-imem
+      - const: syscon
+      - const: simple-mfd
+
+  reg:
+    maxItems: 1
+
+  ranges: true
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 1
+
+  reboot-mode:
+    $ref: /schemas/power/reset/syscon-reboot-mode.yaml#
+
+patternProperties:
+  "^pil-reloc@[0-9a-f]+$":
+    $ref: /schemas/remoteproc/qcom,pil-info.yaml#
+    description: Peripheral image loader relocation region
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        sram@146bf000 {
+            compatible = "qcom,sdm845-imem", "syscon", "simple-mfd";
+            reg = <0 0x146bf000 0 0x1000>;
+            ranges = <0 0 0x146bf000 0x1000>;
+
+            #address-cells = <1>;
+            #size-cells = <1>;
+
+            pil-reloc@94c {
+                compatible = "qcom,pil-reloc-info";
+                reg = <0x94c 0xc8>;
+            };
+        };
+    };

Documentation/devicetree/bindings/sram/qcom,ocmem.yaml

@@ -72,10 +72,10 @@ patternProperties:
 
 examples:
   - |
-      #include <dt-bindings/clock/qcom,rpmcc.h>
-      #include <dt-bindings/clock/qcom,mmcc-msm8974.h>
+    #include <dt-bindings/clock/qcom,rpmcc.h>
+    #include <dt-bindings/clock/qcom,mmcc-msm8974.h>
 
-      ocmem: ocmem@fdd00000 {
+    sram@fdd00000 {
         compatible = "qcom,msm8974-ocmem";
 
         reg = <0xfdd00000 0x2000>,
@@ -93,6 +93,6 @@ examples:
         ranges = <0 0xfec00000 0x100000>;
 
         gmu-sram@0 {
-                reg = <0x0 0x100000>;
+            reg = <0x0 0x100000>;
         };
-      };
+    };

Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml

@@ -16,7 +16,7 @@ description: |+
   - compatible: Should be one of the following:
                 "brcm,bcm2711-avs-monitor", "syscon", "simple-mfd"
 
-  Refer to the the bindings described in
+  Refer to the bindings described in
   Documentation/devicetree/bindings/mfd/syscon.yaml
 
 properties:

Documentation/devicetree/bindings/thermal/nvidia,tegra124-soctherm.txt

@@ -96,7 +96,7 @@ critical trip point is reported back to the thermal framework to implement
 software shutdown.
 
 - the "hot" type trip points will be set to SOC_THERM hardware as the throttle
-temperature. Once the the temperature of this thermal zone is higher
+temperature. Once the temperature of this thermal zone is higher
 than it, it will trigger the HW throttle event.
 
 Example :

Documentation/devicetree/bindings/thermal/rcar-thermal.yaml

@@ -42,7 +42,7 @@ properties:
     description:
       Address ranges of the thermal registers. If more then one range is given
       the first one must be the common registers followed by each sensor
-      according the the datasheet.
+      according the datasheet.
     minItems: 1
     maxItems: 4
 

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -141,6 +141,8 @@ patternProperties:
     description: ASIX Electronics Corporation
   "^aspeed,.*":
     description: ASPEED Technology Inc.
+  "^asrock,.*":
+    description: ASRock Inc.
   "^asus,.*":
     description: AsusTek Computer Inc.
   "^atheros,.*":
@@ -198,12 +200,14 @@ patternProperties:
     description: Broadcom Corporation
   "^bsh,.*":
     description: BSH Hausgeraete GmbH
+  "^bticino,.*":
+    description: Bticino International
   "^buffalo,.*":
     description: Buffalo, Inc.
   "^bur,.*":
     description: B&R Industrial Automation GmbH
-  "^bticino,.*":
-    description: Bticino International
+  "^bytedance,.*":
+    description: ByteDance Ltd.
   "^calamp,.*":
     description: CalAmp Corp.
   "^calaosystems,.*":
@@ -308,6 +312,8 @@ patternProperties:
     description: Dell Inc.
   "^delta,.*":
     description: Delta Electronics, Inc.
+  "^densitron,.*":
+    description: Densitron Technologies Ltd
   "^denx,.*":
     description: Denx Software Engineering
   "^devantech,.*":
@@ -551,6 +557,8 @@ patternProperties:
     description: Shenzhen Hugsun Technology Co. Ltd.
   "^hwacom,.*":
     description: HwaCom Systems Inc.
+  "^hxt,.*":
+    description: HXT Semiconductor
   "^hycon,.*":
     description: Hycon Technology Corp.
   "^hydis,.*":
@@ -585,6 +593,8 @@ patternProperties:
     description: Infineon Technologies
   "^inforce,.*":
     description: Inforce Computing
+  "^ingrasys,.*":
+    description: Ingrasys Technology Inc.
   "^ivo,.*":
     description: InfoVision Optoelectronics Kunshan Co. Ltd.
   "^ingenic,.*":
@@ -605,6 +615,8 @@ patternProperties:
     description: Inter Control Group
   "^invensense,.*":
     description: InvenSense Inc.
+  "^inventec,.*":
+    description: Inventec
   "^inversepath,.*":
     description: Inverse Path
   "^iom,.*":
@@ -1019,6 +1031,8 @@ patternProperties:
     description: Shenzhen QiShenglong Industrialist Co., Ltd.
   "^qnap,.*":
     description: QNAP Systems, Inc.
+  "^quanta,.*":
+    description: Quanta Computer Inc.
   "^radxa,.*":
     description: Radxa
   "^raidsonic,.*":

Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.yaml

@@ -55,7 +55,7 @@ examples:
       compatible = "faraday,ftwdt010";
       reg = <0x41000000 0x1000>;
       interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
-      timeout-secs = <5>;
+      timeout-sec = <5>;
     };
   - |
     watchdog: watchdog@98500000 {

Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.txt

-QCOM PM8916 watchdog timer controller
-
-This pm8916 watchdog timer controller must be under pm8916-pon node.
-
-Required properties:
-- compatible: should be "qcom,pm8916-wdt"
-
-Optional properties :
-- interrupts : Watchdog pre-timeout (bark) interrupt.
-- timeout-sec : Watchdog timeout value in seconds.
-
-Example:
-
-	pm8916_0: pm8916@0 {
-		compatible = "qcom,pm8916", "qcom,spmi-pmic";
-		reg = <0x0 SPMI_USID>;
-
-		pon@800 {
-			compatible = "qcom,pm8916-pon";
-			reg = <0x800>;
-
-			watchdog {
-				compatible = "qcom,pm8916-wdt";
-				interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>;
-				timeout-sec = <10>;
-			};
-		};
-	};

Documentation/devicetree/bindings/watchdog/qcom,pm8916-wdt.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/watchdog/qcom,pm8916-wdt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm PM8916 watchdog timer controller
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+allOf:
+  - $ref: watchdog.yaml#
+
+properties:
+  compatible:
+    const: qcom,pm8916-wdt
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/spmi/spmi.h>
+
+    pmic@0 {
+        compatible = "qcom,pm8916", "qcom,spmi-pmic";
+        reg = <0x0 SPMI_USID>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pon@800 {
+            compatible = "qcom,pm8916-pon";
+            reg = <0x800>;
+            mode-bootloader = <0x2>;
+            mode-recovery = <0x1>;
+
+            watchdog {
+                compatible = "qcom,pm8916-wdt";
+                interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>;
+                timeout-sec = <60>;
+            };
+        };
+    };

Documentation/devicetree/bindings/writing-bindings.rst

@@ -53,7 +53,7 @@ Properties
 
 - DO use common property unit suffixes for properties with scientific units.
   Recommended suffixes are listed at
-  https://github.com/devicetree-org/dt-schema/blob/master/schemas/property-units.yaml
+  https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/property-units.yaml
 
 - DO define properties in terms of constraints. How many entries? What are
   possible values? What is the order?

MAINTAINERS

@@ -2609,7 +2609,7 @@ L:	linux-unisoc@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	Documentation/devicetree/bindings/arm/rda.yaml
 F:	Documentation/devicetree/bindings/gpio/gpio-rda.yaml
-F:	Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.txt
+F:	Documentation/devicetree/bindings/interrupt-controller/rda,8810pl-intc.yaml
 F:	Documentation/devicetree/bindings/serial/rda,8810pl-uart.yaml
 F:	Documentation/devicetree/bindings/timer/rda,8810pl-timer.yaml
 F:	arch/arm/boot/dts/rda8810pl-*
@@ -2689,6 +2689,7 @@ B:	mailto:linux-samsung-soc@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux.git
 F:	Documentation/arm/samsung/
 F:	Documentation/devicetree/bindings/arm/samsung/
+F:	Documentation/devicetree/bindings/hwinfo/samsung,*
 F:	Documentation/devicetree/bindings/power/pd-samsung.yaml
 F:	Documentation/devicetree/bindings/soc/samsung/
 F:	arch/arm/boot/dts/exynos*
@@ -2941,6 +2942,7 @@ M:	Tero Kristo <kristo@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Supported
 F:	Documentation/devicetree/bindings/arm/ti/k3.yaml
+F:	Documentation/devicetree/bindings/hwinfo/ti,k3-socinfo.yaml
 F:	arch/arm64/boot/dts/ti/Makefile
 F:	arch/arm64/boot/dts/ti/k3-*
 F:	include/dt-bindings/pinctrl/k3.h

drivers/of/base.c

@@ -2079,7 +2079,7 @@ struct device_node *of_find_next_cache_node(const struct device_node *np)
  *
  * @cpu: cpu number(logical index) for which the last cache level is needed
  *
- * Return: The the level at which the last cache is present. It is exactly
+ * Return: The level at which the last cache is present. It is exactly
  * same as  the total number of cache levels for the given logical cpu.
  */
 int of_find_last_cache_level(unsigned int cpu)

drivers/of/device.c

@@ -81,8 +81,11 @@ of_dma_set_restricted_buffer(struct device *dev, struct device_node *np)
 		 * restricted-dma-pool region is allowed.
 		 */
 		if (of_device_is_compatible(node, "restricted-dma-pool") &&
-		    of_device_is_available(node))
+		    of_device_is_available(node)) {
+			of_node_put(node);
 			break;
+		}
+		of_node_put(node);
 	}
 
 	/*

drivers/of/fdt.c

@@ -246,7 +246,7 @@ static int populate_node(const void *blob,
 	}
 
 	*pnp = np;
-	return true;
+	return 0;
 }
 
 static void reverse_nodes(struct device_node *parent)
@@ -477,8 +477,8 @@ void *initial_boot_params __ro_after_init;
 
 static u32 of_fdt_crc32;
 
-static int __init early_init_dt_reserve_memory_arch(phys_addr_t base,
-					phys_addr_t size, bool nomap)
+static int __init early_init_dt_reserve_memory(phys_addr_t base,
+					       phys_addr_t size, bool nomap)
 {
 	if (nomap) {
 		/*
@@ -525,15 +525,15 @@ static int __init __reserved_mem_reserve_reg(unsigned long node,
 		size = dt_mem_next_cell(dt_root_size_cells, &prop);
 
 		if (size &&
-		    early_init_dt_reserve_memory_arch(base, size, nomap) == 0) {
+		    early_init_dt_reserve_memory(base, size, nomap) == 0) {
 			pr_debug("Reserved memory: reserved region for node '%s': base %pa, size %lu MiB\n",
 				uname, &base, (unsigned long)(size / SZ_1M));
 			if (!nomap)
 				kmemleak_alloc_phys(base, size, 0, 0);
 		}
 		else
-			pr_info("Reserved memory: failed to reserve memory for node '%s': base %pa, size %lu MiB\n",
-				uname, &base, (unsigned long)(size / SZ_1M));
+			pr_err("Reserved memory: failed to reserve memory for node '%s': base %pa, size %lu MiB\n",
+			       uname, &base, (unsigned long)(size / SZ_1M));
 
 		len -= t_len;
 		if (first) {
@@ -644,7 +644,7 @@ void __init early_init_fdt_scan_reserved_mem(void)
 		fdt_get_mem_rsv(initial_boot_params, n, &base, &size);
 		if (!size)
 			break;
-		early_init_dt_reserve_memory_arch(base, size, false);
+		memblock_reserve(base, size);
 	}
 
 	fdt_scan_reserved_mem();
@@ -661,9 +661,8 @@ void __init early_init_fdt_reserve_self(void)
 		return;
 
 	/* Reserve the dtb region */
-	early_init_dt_reserve_memory_arch(__pa(initial_boot_params),
-					  fdt_totalsize(initial_boot_params),
-					  false);
+	memblock_reserve(__pa(initial_boot_params),
+			 fdt_totalsize(initial_boot_params));
 }
 
 /**

drivers/of/kexec.c

@@ -128,6 +128,7 @@ int __init ima_get_kexec_buffer(void **addr, size_t *size)
 {
 	int ret, len;
 	unsigned long tmp_addr;
+	unsigned long start_pfn, end_pfn;
 	size_t tmp_size;
 	const void *prop;
 
@@ -139,6 +140,22 @@ int __init ima_get_kexec_buffer(void **addr, size_t *size)
 	if (ret)
 		return ret;
 
+	/* Do some sanity on the returned size for the ima-kexec buffer */
+	if (!tmp_size)
+		return -ENOENT;
+
+	/*
+	 * Calculate the PFNs for the buffer and ensure
+	 * they are with in addressable memory.
+	 */
+	start_pfn = PHYS_PFN(tmp_addr);
+	end_pfn = PHYS_PFN(tmp_addr + tmp_size - 1);
+	if (!page_is_ram(start_pfn) || !page_is_ram(end_pfn)) {
+		pr_warn("IMA buffer at 0x%lx, size = 0x%zx beyond memory\n",
+			tmp_addr, tmp_size);
+		return -EINVAL;
+	}
+
 	*addr = __va(tmp_addr);
 	*size = tmp_size;
 

drivers/of/of_reserved_mem.c

@@ -156,7 +156,8 @@ static int __init __reserved_mem_alloc_size(unsigned long node,
 	}
 
 	if (base == 0) {
-		pr_info("failed to allocate memory for node '%s'\n", uname);
+		pr_err("failed to allocate memory for node '%s': size %lu MiB\n",
+		       uname, (unsigned long)(size / SZ_1M));
 		return -ENOMEM;
 	}
 

drivers/of/overlay.c

@@ -903,12 +903,6 @@ static int of_overlay_apply(struct overlay_changeset *ovcs)
 {
 	int ret = 0, ret_revert, ret_tmp;
 
-	if (devicetree_corrupt()) {
-		pr_err("devicetree state suspect, refuse to apply overlay\n");
-		ret = -EBUSY;
-		goto out;
-	}
-
 	ret = of_resolve_phandles(ovcs->overlay_root);
 	if (ret)
 		goto out;
@@ -983,6 +977,11 @@ int of_overlay_fdt_apply(const void *overlay_fdt, u32 overlay_fdt_size,
 
 	*ret_ovcs_id = 0;
 
+	if (devicetree_corrupt()) {
+		pr_err("devicetree state suspect, refuse to apply overlay\n");
+		return -EBUSY;
+	}
+
 	if (overlay_fdt_size < sizeof(struct fdt_header) ||
 	    fdt_check_header(overlay_fdt)) {
 		pr_err("Invalid overlay_fdt header\n");
@@ -1044,20 +1043,15 @@ int of_overlay_fdt_apply(const void *overlay_fdt, u32 overlay_fdt_size,
 	 * goto err_free_ovcs.  Instead, the caller of of_overlay_fdt_apply()
 	 * can call of_overlay_remove();
 	 */
-
-	mutex_unlock(&of_mutex);
-	of_overlay_mutex_unlock();
-
 	*ret_ovcs_id = ovcs->id;
-
-	return ret;
+	goto out_unlock;
 
 err_free_ovcs:
 	free_overlay_changeset(ovcs);
 
+out_unlock:
 	mutex_unlock(&of_mutex);
 	of_overlay_mutex_unlock();
-
 	return ret;
 }
 EXPORT_SYMBOL_GPL(of_overlay_fdt_apply);

drivers/of/unittest.c

@@ -1602,7 +1602,7 @@ static int unittest_gpio_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, devptr);
 
-	devptr->chip.of_node = pdev->dev.of_node;
+	devptr->chip.fwnode = dev_fwnode(&pdev->dev);
 	devptr->chip.label = "of-unittest-gpio";
 	devptr->chip.base = -1; /* dynamic allocation */
 	devptr->chip.ngpio = 5;
@@ -1611,7 +1611,7 @@ static int unittest_gpio_probe(struct platform_device *pdev)
 	ret = gpiochip_add_data(&devptr->chip, NULL);
 
 	unittest(!ret,
-		 "gpiochip_add_data() for node @%pOF failed, ret = %d\n", devptr->chip.of_node, ret);
+		 "gpiochip_add_data() for node @%pfw failed, ret = %d\n", devptr->chip.fwnode, ret);
 
 	if (!ret)
 		unittest_gpio_probe_pass_count++;
@@ -1620,20 +1620,19 @@ static int unittest_gpio_probe(struct platform_device *pdev)
 
 static int unittest_gpio_remove(struct platform_device *pdev)
 {
-	struct unittest_gpio_dev *gdev = platform_get_drvdata(pdev);
+	struct unittest_gpio_dev *devptr = platform_get_drvdata(pdev);
 	struct device *dev = &pdev->dev;
-	struct device_node *np = pdev->dev.of_node;
 
-	dev_dbg(dev, "%s for node @%pOF\n", __func__, np);
+	dev_dbg(dev, "%s for node @%pfw\n", __func__, devptr->chip.fwnode);
 
-	if (!gdev)
+	if (!devptr)
 		return -EINVAL;
 
-	if (gdev->chip.base != -1)
-		gpiochip_remove(&gdev->chip);
+	if (devptr->chip.base != -1)
+		gpiochip_remove(&devptr->chip);
 
 	platform_set_drvdata(pdev, NULL);
-	kfree(gdev);
+	kfree(devptr);
 
 	return 0;
 }

include/dt-bindings/clock/efm32-cmu.h

-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __DT_BINDINGS_CLOCK_EFM32_CMU_H
-#define __DT_BINDINGS_CLOCK_EFM32_CMU_H
-
-#define clk_HFXO		0
-#define clk_HFRCO		1
-#define clk_LFXO		2
-#define clk_LFRCO		3
-#define clk_ULFRCO		4
-#define clk_AUXHFRCO		5
-#define clk_HFCLKNODIV		6
-#define clk_HFCLK		7
-#define clk_HFPERCLK		8
-#define clk_HFCORECLK		9
-#define clk_LFACLK		10
-#define clk_LFBCLK		11
-#define clk_WDOGCLK		12
-#define clk_HFCORECLKDMA	13
-#define clk_HFCORECLKAES	14
-#define clk_HFCORECLKUSBC	15
-#define clk_HFCORECLKUSB	16
-#define clk_HFCORECLKLE		17
-#define clk_HFCORECLKEBI	18
-#define clk_HFPERCLKUSART0	19
-#define clk_HFPERCLKUSART1	20
-#define clk_HFPERCLKUSART2	21
-#define clk_HFPERCLKUART0	22
-#define clk_HFPERCLKUART1	23
-#define clk_HFPERCLKTIMER0	24
-#define clk_HFPERCLKTIMER1	25
-#define clk_HFPERCLKTIMER2	26
-#define clk_HFPERCLKTIMER3	27
-#define clk_HFPERCLKACMP0	28
-#define clk_HFPERCLKACMP1	29
-#define clk_HFPERCLKI2C0	30
-#define clk_HFPERCLKI2C1	31
-#define clk_HFPERCLKGPIO	32
-#define clk_HFPERCLKVCMP	33
-#define clk_HFPERCLKPRS		34
-#define clk_HFPERCLKADC0	35
-#define clk_HFPERCLKDAC0	36
-
-#endif /* __DT_BINDINGS_CLOCK_EFM32_CMU_H */

include/linux/of.h

@@ -207,7 +207,7 @@ static inline void of_node_clear_flag(struct device_node *n, unsigned long flag)
 }
 
 #if defined(CONFIG_OF_DYNAMIC) || defined(CONFIG_SPARC)
-static inline int of_property_check_flag(struct property *p, unsigned long flag)
+static inline int of_property_check_flag(const struct property *p, unsigned long flag)
 {
 	return test_bit(flag, &p->_flags);
 }
@@ -812,7 +812,8 @@ static inline void of_node_clear_flag(struct device_node *n, unsigned long flag)
 {
 }
 
-static inline int of_property_check_flag(struct property *p, unsigned long flag)
+static inline int of_property_check_flag(const struct property *p,
+					 unsigned long flag)
 {
 	return 0;
 }