Commit db2932ec authored by Bruce Allan's avatar Bruce Allan Committed by David S. Miller

e1000e: clear PHY wakeup bit after LCD reset on 82577/82578

Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset.  If this bit remains set, link
problems may occur.
Signed-off-by: default avatarBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 39305965
...@@ -844,7 +844,7 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) ...@@ -844,7 +844,7 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
u32 i; u32 i;
u32 data, cnf_size, cnf_base_addr, sw_cfg_mask; u32 data, cnf_size, cnf_base_addr, sw_cfg_mask;
s32 ret_val; s32 ret_val;
u16 word_addr, reg_data, reg_addr, phy_page = 0; u16 reg, word_addr, reg_data, reg_addr, phy_page = 0;
ret_val = e1000e_phy_hw_reset_generic(hw); ret_val = e1000e_phy_hw_reset_generic(hw);
if (ret_val) if (ret_val)
...@@ -859,6 +859,10 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) ...@@ -859,6 +859,10 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
return ret_val; return ret_val;
} }
/* Dummy read to clear the phy wakeup bit after lcd reset */
if (hw->mac.type == e1000_pchlan)
e1e_rphy(hw, BM_WUC, &reg);
/* /*
* Initialize the PHY from the NVM on ICH platforms. This * Initialize the PHY from the NVM on ICH platforms. This
* is needed due to an issue where the NVM configuration is * is needed due to an issue where the NVM configuration is
...@@ -2229,6 +2233,7 @@ static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw) ...@@ -2229,6 +2233,7 @@ static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw)
**/ **/
static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
{ {
u16 reg;
u32 ctrl, icr, kab; u32 ctrl, icr, kab;
s32 ret_val; s32 ret_val;
...@@ -2304,6 +2309,9 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ...@@ -2304,6 +2309,9 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
hw_dbg(hw, "Auto Read Done did not complete\n"); hw_dbg(hw, "Auto Read Done did not complete\n");
} }
} }
/* Dummy read to clear the phy wakeup bit after lcd reset */
if (hw->mac.type == e1000_pchlan)
e1e_rphy(hw, BM_WUC, &reg);
/* /*
* For PCH, this write will make sure that any noise * For PCH, this write will make sure that any noise
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment