Commit dd0cdd88 authored by Tony Lindgren's avatar Tony Lindgren

omap: Move omap1 USB platform init code into mach-omap1/usb.c

Move omap1 FS USB platform init code into mach-omap1/usb.c
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent 98093839
......@@ -23,6 +23,9 @@ obj-y += $(i2c-omap-m) $(i2c-omap-y)
led-y := leds.o
usb-fs-$(CONFIG_USB) := usb.o
obj-y += $(usb-fs-m) $(usb-fs-y)
# Specific board support
obj-$(CONFIG_MACH_OMAP_H2) += board-h2.o board-h2-mmc.o
obj-$(CONFIG_MACH_OMAP_INNOVATOR) += board-innovator.o
......
......@@ -235,7 +235,7 @@ static void __init ams_delta_init(void)
/* Clear latch2 (NAND, LCD, modem enable) */
ams_delta_latch2_write(~0, 0);
omap_usb_init(&ams_delta_usb_config);
omap1_usb_init(&ams_delta_usb_config);
platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices));
#ifdef CONFIG_AMS_DELTA_FIQ
......
......@@ -72,12 +72,12 @@ static void __init omap_generic_init(void)
omap_cfg_reg(UART3_TX);
omap_cfg_reg(UART3_RX);
omap_usb_init(&generic1510_usb_config);
omap1_usb_init(&generic1510_usb_config);
}
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (!cpu_is_omap1510()) {
omap_usb_init(&generic1610_usb_config);
omap1_usb_init(&generic1610_usb_config);
}
#endif
......
......@@ -452,7 +452,7 @@ static void __init h2_init(void)
omap_serial_init();
omap_register_i2c_bus(1, 100, h2_i2c_board_info,
ARRAY_SIZE(h2_i2c_board_info));
omap_usb_init(&h2_usb_config);
omap1_usb_init(&h2_usb_config);
h2_mmc_init();
}
......
......@@ -405,7 +405,7 @@ static void __init h3_init(void)
omap_serial_init();
omap_register_i2c_bus(1, 100, h3_i2c_board_info,
ARRAY_SIZE(h3_i2c_board_info));
omap_usb_init(&h3_usb_config);
omap1_usb_init(&h3_usb_config);
h3_mmc_init();
}
......
......@@ -287,7 +287,7 @@ static void __init htcherald_init(void)
htcherald_disable_watchdog();
htcherald_usb_enable();
omap_usb_init(&htcherald_usb_config);
omap1_usb_init(&htcherald_usb_config);
}
static void __init htcherald_init_irq(void)
......
......@@ -422,13 +422,13 @@ static void __init innovator_init(void)
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
omap_usb_init(&innovator1510_usb_config);
omap1_usb_init(&innovator1510_usb_config);
innovator_config[1].data = &innovator1510_lcd_config;
}
#endif
#ifdef CONFIG_ARCH_OMAP16XX
if (cpu_is_omap1610()) {
omap_usb_init(&h2_usb_config);
omap1_usb_init(&h2_usb_config);
innovator_config[1].data = &innovator1610_lcd_config;
}
#endif
......
......@@ -386,7 +386,7 @@ static void __init omap_nokia770_init(void)
hwa742_dev_init();
ads7846_dev_init();
mipid_dev_init();
omap_usb_init(&nokia770_usb_config);
omap1_usb_init(&nokia770_usb_config);
nokia770_mmc_init();
}
......
......@@ -560,7 +560,7 @@ static void __init osk_init(void)
l |= (3 << 1);
omap_writel(l, USB_TRANSCEIVER_CTRL);
omap_usb_init(&osk_usb_config);
omap1_usb_init(&osk_usb_config);
/* irq for tps65010 chip */
/* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */
......
......@@ -359,7 +359,7 @@ static void __init omap_palmte_init(void)
spi_register_board_info(palmte_spi_info, ARRAY_SIZE(palmte_spi_info));
palmte_misc_gpio_setup();
omap_serial_init();
omap_usb_init(&palmte_usb_config);
omap1_usb_init(&palmte_usb_config);
omap_register_i2c_bus(1, 100, NULL, 0);
}
......
......@@ -307,7 +307,7 @@ static void __init omap_palmtt_init(void)
spi_register_board_info(palmtt_boardinfo,ARRAY_SIZE(palmtt_boardinfo));
omap_serial_init();
omap_usb_init(&palmtt_usb_config);
omap1_usb_init(&palmtt_usb_config);
omap_register_i2c_bus(1, 100, NULL, 0);
}
......
......@@ -325,7 +325,7 @@ omap_palmz71_init(void)
spi_register_board_info(palmz71_boardinfo,
ARRAY_SIZE(palmz71_boardinfo));
omap_usb_init(&palmz71_usb_config);
omap1_usb_init(&palmz71_usb_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
palmz71_gpio_setup(0);
......
......@@ -392,7 +392,7 @@ static void __init omap_sx1_init(void)
omap_board_config_size = ARRAY_SIZE(sx1_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
omap_usb_init(&sx1_usb_config);
omap1_usb_init(&sx1_usb_config);
sx1_mmc_init();
/* turn on USB power */
......
......@@ -198,7 +198,7 @@ static void __init voiceblue_init(void)
omap_board_config = voiceblue_config;
omap_board_config_size = ARRAY_SIZE(voiceblue_config);
omap_serial_init();
omap_usb_init(&voiceblue_usb_config);
omap1_usb_init(&voiceblue_usb_config);
omap_register_i2c_bus(1, 100, NULL, 0);
/* There is a good chance board is going up, so enable power LED
......
/*
* Platform level USB initialization for FS USB OTG controller on omap1 and 24xx
*
* Copyright (C) 2004 Texas Instruments, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <plat/mux.h>
#include <plat/usb.h>
/* These routines should handle the standard chip-specific modes
* for usb0/1/2 ports, covering basic mux and transceiver setup.
*
* Some board-*.c files will need to set up additional mux options,
* like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
*/
/* TESTED ON:
* - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
* - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
* - 5912 OSK UDC, with *nonstandard* A-to-A cable
* - 1510 Innovator UDC with bundled usb0 cable
* - 1510 Innovator OHCI with bundled usb1/usb2 cable
* - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
* - 1710 custom development board using alternate pin group
* - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
*/
#define INT_USB_IRQ_GEN IH2_BASE + 20
#define INT_USB_IRQ_NISO IH2_BASE + 30
#define INT_USB_IRQ_ISO IH2_BASE + 29
#define INT_USB_IRQ_HGEN INT_USB_HHC_1
#define INT_USB_IRQ_OTG IH2_BASE + 8
#ifdef CONFIG_USB_GADGET_OMAP
static struct resource udc_resources[] = {
/* order is significant! */
{ /* registers */
.start = UDC_BASE,
.end = UDC_BASE + 0xff,
.flags = IORESOURCE_MEM,
}, { /* general IRQ */
.start = INT_USB_IRQ_GEN,
.flags = IORESOURCE_IRQ,
}, { /* PIO IRQ */
.start = INT_USB_IRQ_NISO,
.flags = IORESOURCE_IRQ,
}, { /* SOF IRQ */
.start = INT_USB_IRQ_ISO,
.flags = IORESOURCE_IRQ,
},
};
static u64 udc_dmamask = ~(u32)0;
static struct platform_device udc_device = {
.name = "omap_udc",
.id = -1,
.dev = {
.dma_mask = &udc_dmamask,
.coherent_dma_mask = 0xffffffff,
},
.num_resources = ARRAY_SIZE(udc_resources),
.resource = udc_resources,
};
static inline void udc_device_init(struct omap_usb_config *pdata)
{
/* IRQ numbers for omap7xx */
if(cpu_is_omap7xx()) {
udc_resources[1].start = INT_7XX_USB_GENI;
udc_resources[2].start = INT_7XX_USB_NON_ISO;
udc_resources[3].start = INT_7XX_USB_ISO;
}
pdata->udc_device = &udc_device;
}
#else
static inline void udc_device_init(struct omap_usb_config *pdata)
{
}
#endif
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* The dmamask must be set for OHCI to work */
static u64 ohci_dmamask = ~(u32)0;
static struct resource ohci_resources[] = {
{
.start = OMAP_OHCI_BASE,
.end = OMAP_OHCI_BASE + 0xff,
.flags = IORESOURCE_MEM,
},
{
.start = INT_USB_IRQ_HGEN,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device ohci_device = {
.name = "ohci",
.id = -1,
.dev = {
.dma_mask = &ohci_dmamask,
.coherent_dma_mask = 0xffffffff,
},
.num_resources = ARRAY_SIZE(ohci_resources),
.resource = ohci_resources,
};
static inline void ohci_device_init(struct omap_usb_config *pdata)
{
if (cpu_is_omap7xx())
ohci_resources[1].start = INT_7XX_USB_HHC_1;
pdata->ohci_device = &ohci_device;
}
#else
static inline void ohci_device_init(struct omap_usb_config *pdata)
{
}
#endif
#if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
static struct resource otg_resources[] = {
/* order is significant! */
{
.start = OTG_BASE,
.end = OTG_BASE + 0xff,
.flags = IORESOURCE_MEM,
}, {
.start = INT_USB_IRQ_OTG,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device otg_device = {
.name = "omap_otg",
.id = -1,
.num_resources = ARRAY_SIZE(otg_resources),
.resource = otg_resources,
};
static inline void otg_device_init(struct omap_usb_config *pdata)
{
if (cpu_is_omap7xx())
otg_resources[1].start = INT_7XX_USB_OTG;
pdata->otg_device = &otg_device;
}
#else
static inline void otg_device_init(struct omap_usb_config *pdata)
{
}
#endif
u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
{
u32 syscon1 = 0;
if (nwires == 0) {
if (!cpu_is_omap15xx()) {
u32 l;
/* pulldown D+/D- */
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~(3 << 1);
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
return 0;
}
if (is_device) {
if (cpu_is_omap7xx()) {
omap_cfg_reg(AA17_7XX_USB_DM);
omap_cfg_reg(W16_7XX_USB_PU_EN);
omap_cfg_reg(W17_7XX_USB_VBUSI);
omap_cfg_reg(W18_7XX_USB_DMCK_OUT);
omap_cfg_reg(W19_7XX_USB_DCRST);
} else
omap_cfg_reg(W4_USB_PUEN);
}
if (nwires == 2) {
u32 l;
// omap_cfg_reg(P9_USB_DP);
// omap_cfg_reg(R8_USB_DM);
if (cpu_is_omap15xx()) {
/* This works on 1510-Innovator */
return 0;
}
/* NOTES:
* - peripheral should configure VBUS detection!
* - only peripherals may use the internal D+/D- pulldowns
* - OTG support on this port not yet written
*/
/* Don't do this for omap7xx -- it causes USB to not work correctly */
if (!cpu_is_omap7xx()) {
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~(7 << 4);
if (!is_device)
l |= (3 << 1);
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
return 3 << 16;
}
/* alternate pin config, external transceiver */
if (cpu_is_omap15xx()) {
printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
return 0;
}
omap_cfg_reg(V6_USB0_TXD);
omap_cfg_reg(W9_USB0_TXEN);
omap_cfg_reg(W5_USB0_SE0);
if (nwires != 3)
omap_cfg_reg(Y5_USB0_RCV);
/* NOTE: SPEED and SUSP aren't configured here. OTG hosts
* may be able to use I2C requests to set those bits along
* with VBUS switching and overcurrent detection.
*/
if (nwires != 6) {
u32 l;
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~CONF_USB2_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
switch (nwires) {
case 3:
syscon1 = 2;
break;
case 4:
syscon1 = 1;
break;
case 6:
syscon1 = 3;
{
u32 l;
omap_cfg_reg(AA9_USB0_VP);
omap_cfg_reg(R9_USB0_VM);
l = omap_readl(USB_TRANSCEIVER_CTRL);
l |= CONF_USB2_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
break;
default:
printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
0, nwires);
}
return syscon1 << 16;
}
u32 __init omap1_usb1_init(unsigned nwires)
{
u32 syscon1 = 0;
if (!cpu_is_omap15xx() && nwires != 6) {
u32 l;
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~CONF_USB1_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
if (nwires == 0)
return 0;
/* external transceiver */
omap_cfg_reg(USB1_TXD);
omap_cfg_reg(USB1_TXEN);
if (nwires != 3)
omap_cfg_reg(USB1_RCV);
if (cpu_is_omap15xx()) {
omap_cfg_reg(USB1_SEO);
omap_cfg_reg(USB1_SPEED);
// SUSP
} else if (cpu_is_omap1610() || cpu_is_omap5912()) {
omap_cfg_reg(W13_1610_USB1_SE0);
omap_cfg_reg(R13_1610_USB1_SPEED);
// SUSP
} else if (cpu_is_omap1710()) {
omap_cfg_reg(R13_1710_USB1_SE0);
// SUSP
} else {
pr_debug("usb%d cpu unrecognized\n", 1);
return 0;
}
switch (nwires) {
case 2:
goto bad;
case 3:
syscon1 = 2;
break;
case 4:
syscon1 = 1;
break;
case 6:
syscon1 = 3;
omap_cfg_reg(USB1_VP);
omap_cfg_reg(USB1_VM);
if (!cpu_is_omap15xx()) {
u32 l;
l = omap_readl(USB_TRANSCEIVER_CTRL);
l |= CONF_USB1_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
break;
default:
bad:
printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
1, nwires);
}
return syscon1 << 20;
}
u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
{
u32 syscon1 = 0;
/* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
if (alt_pingroup || nwires == 0)
return 0;
if (!cpu_is_omap15xx() && nwires != 6) {
u32 l;
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~CONF_USB2_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
/* external transceiver */
if (cpu_is_omap15xx()) {
omap_cfg_reg(USB2_TXD);
omap_cfg_reg(USB2_TXEN);
omap_cfg_reg(USB2_SEO);
if (nwires != 3)
omap_cfg_reg(USB2_RCV);
/* there is no USB2_SPEED */
} else if (cpu_is_omap16xx()) {
omap_cfg_reg(V6_USB2_TXD);
omap_cfg_reg(W9_USB2_TXEN);
omap_cfg_reg(W5_USB2_SE0);
if (nwires != 3)
omap_cfg_reg(Y5_USB2_RCV);
// FIXME omap_cfg_reg(USB2_SPEED);
} else {
pr_debug("usb%d cpu unrecognized\n", 1);
return 0;
}
// omap_cfg_reg(USB2_SUSP);
switch (nwires) {
case 2:
goto bad;
case 3:
syscon1 = 2;
break;
case 4:
syscon1 = 1;
break;
case 5:
goto bad;
case 6:
syscon1 = 3;
if (cpu_is_omap15xx()) {
omap_cfg_reg(USB2_VP);
omap_cfg_reg(USB2_VM);
} else {
u32 l;
omap_cfg_reg(AA9_USB2_VP);
omap_cfg_reg(R9_USB2_VM);
l = omap_readl(USB_TRANSCEIVER_CTRL);
l |= CONF_USB2_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
break;
default:
bad:
printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
2, nwires);
}
return syscon1 << 24;
}
#ifdef CONFIG_ARCH_OMAP15XX
/* ULPD_DPLL_CTRL */
#define DPLL_IOB (1 << 13)
#define DPLL_PLL_ENABLE (1 << 4)
#define DPLL_LOCK (1 << 0)
/* ULPD_APLL_CTRL */
#define APLL_NDPLL_SWITCH (1 << 0)
static void __init omap_1510_usb_init(struct omap_usb_config *config)
{
unsigned int val;
u16 w;
config->usb0_init(config->pins[0], is_usb0_device(config));
config->usb1_init(config->pins[1]);
config->usb2_init(config->pins[2], 0);
val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
val |= (config->hmc_mode << 1);
omap_writel(val, MOD_CONF_CTRL_0);
printk("USB: hmc %d", config->hmc_mode);
if (config->pins[0])
printk(", usb0 %d wires%s", config->pins[0],
is_usb0_device(config) ? " (dev)" : "");
if (config->pins[1])
printk(", usb1 %d wires", config->pins[1]);
if (config->pins[2])
printk(", usb2 %d wires", config->pins[2]);
printk("\n");
/* use DPLL for 48 MHz function clock */
pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));
w = omap_readw(ULPD_APLL_CTRL);
w &= ~APLL_NDPLL_SWITCH;
omap_writew(w, ULPD_APLL_CTRL);
w = omap_readw(ULPD_DPLL_CTRL);
w |= DPLL_IOB | DPLL_PLL_ENABLE;
omap_writew(w, ULPD_DPLL_CTRL);
w = omap_readw(ULPD_SOFT_REQ);
w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
omap_writew(w, ULPD_SOFT_REQ);
while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
cpu_relax();
#ifdef CONFIG_USB_GADGET_OMAP
if (config->register_dev) {
int status;
udc_device.dev.platform_data = config;
status = platform_device_register(&udc_device);
if (status)
pr_debug("can't register UDC device, %d\n", status);
/* udc driver gates 48MHz by D+ pullup */
}
#endif
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
if (config->register_host) {
int status;
ohci_device.dev.platform_data = config;
status = platform_device_register(&ohci_device);
if (status)
pr_debug("can't register OHCI device, %d\n", status);
/* hcd explicitly gates 48MHz */
}
#endif
}
#else
static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
#endif
void __init omap1_usb_init(struct omap_usb_config *pdata)
{
pdata->usb0_init = omap1_usb0_init;
pdata->usb1_init = omap1_usb1_init;
pdata->usb2_init = omap1_usb2_init;
udc_device_init(pdata);
ohci_device_init(pdata);
otg_device_init(pdata);
if (cpu_is_omap7xx() || cpu_is_omap16xx())
omap_otg_init(pdata);
else if (cpu_is_omap15xx())
omap_1510_usb_init(pdata);
else
printk(KERN_ERR "USB: No init for your chip yet\n");
}
......@@ -81,8 +81,28 @@ extern void usb_ohci_init(const struct ohci_hcd_omap_platform_data *pdata);
#endif
/*
* FIXME correct answer depends on hmc_mode,
* as does (on omap1) any nonzero value for config->otg port number
*/
#ifdef CONFIG_USB_GADGET_OMAP
#define is_usb0_device(config) 1
#else
#define is_usb0_device(config) 0
#endif
void omap_otg_init(struct omap_usb_config *config);
void omap_usb_init(struct omap_usb_config *pdata);
#if defined(CONFIG_USB) || defined(CONFIG_USB_MODULE)
void omap1_usb_init(struct omap_usb_config *pdata);
#else
static inline void omap1_usb_init(struct omap_usb_config *pdata)
{
}
#endif
#if defined(CONFIG_ARCH_OMAP_OTG) || defined(CONFIG_ARCH_OMAP_OTG_MODULE)
void omap2_usbfs_init(struct omap_usb_config *pdata);
#else
static inline omap2_usbfs_init(struct omap_usb_config *pdata)
......@@ -199,4 +219,24 @@ static inline omap2_usbfs_init(struct omap_usb_config *pdata)
# define USB0PUENACTLOI (1 << 16)
# define USBSTANDBYCTRL (1 << 15)
#if defined(CONFIG_ARCH_OMAP1) && defined(CONFIG_USB)
u32 omap1_usb0_init(unsigned nwires, unsigned is_device);
u32 omap1_usb1_init(unsigned nwires);
u32 omap1_usb2_init(unsigned nwires, unsigned alt_pingroup);
#else
static inline u32 omap1_usb0_init(unsigned nwires, unsigned is_device)
{
return 0;
}
static inline u32 omap1_usb1_init(unsigned nwires)
{
return 0;
}
static inline u32 omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
{
return 0;
}
#endif
#endif /* __ASM_ARCH_OMAP_USB_H */
......@@ -22,434 +22,13 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/usb/otg.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <mach/hardware.h>
#include <plat/control.h>
#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
#define INT_USB_IRQ_GEN IH2_BASE + 20
#define INT_USB_IRQ_NISO IH2_BASE + 30
#define INT_USB_IRQ_ISO IH2_BASE + 29
#define INT_USB_IRQ_HGEN INT_USB_HHC_1
#define INT_USB_IRQ_OTG IH2_BASE + 8
/* These routines should handle the standard chip-specific modes
* for usb0/1/2 ports, covering basic mux and transceiver setup.
*
* Some board-*.c files will need to set up additional mux options,
* like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
*/
/* TESTED ON:
* - 1611B H2 (with usb1 mini-AB) using standard Mini-B or OTG cables
* - 5912 OSK OHCI (with usb0 standard-A), standard A-to-B cables
* - 5912 OSK UDC, with *nonstandard* A-to-A cable
* - 1510 Innovator UDC with bundled usb0 cable
* - 1510 Innovator OHCI with bundled usb1/usb2 cable
* - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
* - 1710 custom development board using alternate pin group
* - 1710 H3 (with usb1 mini-AB) using standard Mini-B or OTG cables
*/
/*-------------------------------------------------------------------------*/
#if defined(CONFIG_ARCH_OMAP_OTG) || defined(CONFIG_ARCH_OMAP15XX)
static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device)
{
u32 syscon1 = 0;
if (nwires == 0) {
if (!cpu_is_omap15xx()) {
u32 l;
/* pulldown D+/D- */
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~(3 << 1);
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
return 0;
}
if (is_device) {
if (cpu_is_omap7xx()) {
omap_cfg_reg(AA17_7XX_USB_DM);
omap_cfg_reg(W16_7XX_USB_PU_EN);
omap_cfg_reg(W17_7XX_USB_VBUSI);
omap_cfg_reg(W18_7XX_USB_DMCK_OUT);
omap_cfg_reg(W19_7XX_USB_DCRST);
} else
omap_cfg_reg(W4_USB_PUEN);
}
if (nwires == 2) {
u32 l;
// omap_cfg_reg(P9_USB_DP);
// omap_cfg_reg(R8_USB_DM);
if (cpu_is_omap15xx()) {
/* This works on 1510-Innovator */
return 0;
}
/* NOTES:
* - peripheral should configure VBUS detection!
* - only peripherals may use the internal D+/D- pulldowns
* - OTG support on this port not yet written
*/
/* Don't do this for omap7xx -- it causes USB to not work correctly */
if (!cpu_is_omap7xx()) {
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~(7 << 4);
if (!is_device)
l |= (3 << 1);
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
return 3 << 16;
}
/* alternate pin config, external transceiver */
if (cpu_is_omap15xx()) {
printk(KERN_ERR "no usb0 alt pin config on 15xx\n");
return 0;
}
omap_cfg_reg(V6_USB0_TXD);
omap_cfg_reg(W9_USB0_TXEN);
omap_cfg_reg(W5_USB0_SE0);
if (nwires != 3)
omap_cfg_reg(Y5_USB0_RCV);
/* NOTE: SPEED and SUSP aren't configured here. OTG hosts
* may be able to use I2C requests to set those bits along
* with VBUS switching and overcurrent detection.
*/
if (nwires != 6) {
u32 l;
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~CONF_USB2_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
switch (nwires) {
case 3:
syscon1 = 2;
break;
case 4:
syscon1 = 1;
break;
case 6:
syscon1 = 3;
{
u32 l;
omap_cfg_reg(AA9_USB0_VP);
omap_cfg_reg(R9_USB0_VM);
l = omap_readl(USB_TRANSCEIVER_CTRL);
l |= CONF_USB2_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
break;
default:
printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
0, nwires);
}
return syscon1 << 16;
}
static u32 __init omap_usb1_init(unsigned nwires)
{
u32 syscon1 = 0;
if (!cpu_is_omap15xx() && nwires != 6) {
u32 l;
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~CONF_USB1_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
if (nwires == 0)
return 0;
/* external transceiver */
omap_cfg_reg(USB1_TXD);
omap_cfg_reg(USB1_TXEN);
if (nwires != 3)
omap_cfg_reg(USB1_RCV);
if (cpu_is_omap15xx()) {
omap_cfg_reg(USB1_SEO);
omap_cfg_reg(USB1_SPEED);
// SUSP
} else if (cpu_is_omap1610() || cpu_is_omap5912()) {
omap_cfg_reg(W13_1610_USB1_SE0);
omap_cfg_reg(R13_1610_USB1_SPEED);
// SUSP
} else if (cpu_is_omap1710()) {
omap_cfg_reg(R13_1710_USB1_SE0);
// SUSP
} else {
pr_debug("usb%d cpu unrecognized\n", 1);
return 0;
}
switch (nwires) {
case 2:
goto bad;
case 3:
syscon1 = 2;
break;
case 4:
syscon1 = 1;
break;
case 6:
syscon1 = 3;
omap_cfg_reg(USB1_VP);
omap_cfg_reg(USB1_VM);
if (!cpu_is_omap15xx()) {
u32 l;
l = omap_readl(USB_TRANSCEIVER_CTRL);
l |= CONF_USB1_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
break;
default:
bad:
printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
1, nwires);
}
return syscon1 << 20;
}
static u32 __init omap_usb2_init(unsigned nwires, unsigned alt_pingroup)
{
u32 syscon1 = 0;
/* NOTE omap1 erratum: must leave USB2_UNI_R set if usb0 in use */
if (alt_pingroup || nwires == 0)
return 0;
if (!cpu_is_omap15xx() && nwires != 6) {
u32 l;
l = omap_readl(USB_TRANSCEIVER_CTRL);
l &= ~CONF_USB2_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
/* external transceiver */
if (cpu_is_omap15xx()) {
omap_cfg_reg(USB2_TXD);
omap_cfg_reg(USB2_TXEN);
omap_cfg_reg(USB2_SEO);
if (nwires != 3)
omap_cfg_reg(USB2_RCV);
/* there is no USB2_SPEED */
} else if (cpu_is_omap16xx()) {
omap_cfg_reg(V6_USB2_TXD);
omap_cfg_reg(W9_USB2_TXEN);
omap_cfg_reg(W5_USB2_SE0);
if (nwires != 3)
omap_cfg_reg(Y5_USB2_RCV);
// FIXME omap_cfg_reg(USB2_SPEED);
} else {
pr_debug("usb%d cpu unrecognized\n", 1);
return 0;
}
// omap_cfg_reg(USB2_SUSP);
switch (nwires) {
case 2:
goto bad;
case 3:
syscon1 = 2;
break;
case 4:
syscon1 = 1;
break;
case 5:
goto bad;
case 6:
syscon1 = 3;
if (cpu_is_omap15xx()) {
omap_cfg_reg(USB2_VP);
omap_cfg_reg(USB2_VM);
} else {
u32 l;
omap_cfg_reg(AA9_USB2_VP);
omap_cfg_reg(R9_USB2_VM);
l = omap_readl(USB_TRANSCEIVER_CTRL);
l |= CONF_USB2_UNI_R;
omap_writel(l, USB_TRANSCEIVER_CTRL);
}
break;
default:
bad:
printk(KERN_ERR "illegal usb%d %d-wire transceiver\n",
2, nwires);
}
return syscon1 << 24;
}
#else
#define omap_usb0_init NULL
#define omap_usb1_init NULL
#define omap_usb2_init NULL
#endif
/*-------------------------------------------------------------------------*/
#ifdef CONFIG_USB_GADGET_OMAP
static struct resource udc_resources[] = {
/* order is significant! */
{ /* registers */
.start = UDC_BASE,
.end = UDC_BASE + 0xff,
.flags = IORESOURCE_MEM,
}, { /* general IRQ */
.start = INT_USB_IRQ_GEN,
.flags = IORESOURCE_IRQ,
}, { /* PIO IRQ */
.start = INT_USB_IRQ_NISO,
.flags = IORESOURCE_IRQ,
}, { /* SOF IRQ */
.start = INT_USB_IRQ_ISO,
.flags = IORESOURCE_IRQ,
},
};
static u64 udc_dmamask = ~(u32)0;
static struct platform_device udc_device = {
.name = "omap_udc",
.id = -1,
.dev = {
.dma_mask = &udc_dmamask,
.coherent_dma_mask = 0xffffffff,
},
.num_resources = ARRAY_SIZE(udc_resources),
.resource = udc_resources,
};
static inline void udc_device_init(struct omap_usb_config *pdata)
{
pdata->udc_device = &udc_device;
}
#else
static inline void udc_device_init(struct omap_usb_config *pdata)
{
}
#endif
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* The dmamask must be set for OHCI to work */
static u64 ohci_dmamask = ~(u32)0;
static struct resource ohci_resources[] = {
{
.start = OMAP_OHCI_BASE,
.end = OMAP_OHCI_BASE + 0xff,
.flags = IORESOURCE_MEM,
},
{
.start = INT_USB_IRQ_HGEN,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device ohci_device = {
.name = "ohci",
.id = -1,
.dev = {
.dma_mask = &ohci_dmamask,
.coherent_dma_mask = 0xffffffff,
},
.num_resources = ARRAY_SIZE(ohci_resources),
.resource = ohci_resources,
};
static inline void ohci_device_init(struct omap_usb_config *pdata)
{
pdata->ohci_device = &ohci_device;
}
#else
static inline void ohci_device_init(struct omap_usb_config *pdata)
{
}
#endif
#if defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
static struct resource otg_resources[] = {
/* order is significant! */
{
.start = OTG_BASE,
.end = OTG_BASE + 0xff,
.flags = IORESOURCE_MEM,
}, {
.start = INT_USB_IRQ_OTG,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device otg_device = {
.name = "omap_otg",
.id = -1,
.num_resources = ARRAY_SIZE(otg_resources),
.resource = otg_resources,
};
static inline void otg_device_init(struct omap_usb_config *pdata)
{
pdata->otg_device = &otg_device;
}
#else
static inline void otg_device_init(struct omap_usb_config *pdata)
{
}
#endif
/*-------------------------------------------------------------------------*/
// FIXME correct answer depends on hmc_mode,
// as does (on omap1) any nonzero value for config->otg port number
#ifdef CONFIG_USB_GADGET_OMAP
#define is_usb0_device(config) 1
#else
#define is_usb0_device(config) 0
#endif
/*-------------------------------------------------------------------------*/
#ifdef CONFIG_ARCH_OMAP_OTG
void __init
......@@ -524,12 +103,6 @@ omap_otg_init(struct omap_usb_config *config)
syscon &= ~DEV_IDLE_EN;
udc_device->dev.platform_data = config;
/* IRQ numbers for omap7xx */
if(cpu_is_omap7xx()) {
udc_resources[1].start = INT_7XX_USB_GENI;
udc_resources[2].start = INT_7XX_USB_NON_ISO;
udc_resources[3].start = INT_7XX_USB_ISO;
}
status = platform_device_register(udc_device);
if (status)
pr_debug("can't register UDC device, %d\n", status);
......@@ -542,8 +115,6 @@ omap_otg_init(struct omap_usb_config *config)
syscon &= ~HST_IDLE_EN;
ohci_device->dev.platform_data = config;
if (cpu_is_omap7xx())
ohci_resources[1].start = INT_7XX_USB_HHC_1;
status = platform_device_register(ohci_device);
if (status)
pr_debug("can't register OHCI device, %d\n", status);
......@@ -556,8 +127,6 @@ omap_otg_init(struct omap_usb_config *config)
syscon &= ~OTG_IDLE_EN;
otg_device->dev.platform_data = config;
if (cpu_is_omap7xx())
otg_resources[1].start = INT_7XX_USB_OTG;
status = platform_device_register(otg_device);
if (status)
pr_debug("can't register OTG device, %d\n", status);
......@@ -572,107 +141,3 @@ omap_otg_init(struct omap_usb_config *config)
#else
void omap_otg_init(struct omap_usb_config *config) {}
#endif
/*-------------------------------------------------------------------------*/
#ifdef CONFIG_ARCH_OMAP15XX
/* ULPD_DPLL_CTRL */
#define DPLL_IOB (1 << 13)
#define DPLL_PLL_ENABLE (1 << 4)
#define DPLL_LOCK (1 << 0)
/* ULPD_APLL_CTRL */
#define APLL_NDPLL_SWITCH (1 << 0)
static void __init omap_1510_usb_init(struct omap_usb_config *config)
{
unsigned int val;
u16 w;
config->usb0_init(config->pins[0], is_usb0_device(config));
config->usb1_init(config->pins[1]);
config->usb2_init(config->pins[2], 0);
val = omap_readl(MOD_CONF_CTRL_0) & ~(0x3f << 1);
val |= (config->hmc_mode << 1);
omap_writel(val, MOD_CONF_CTRL_0);
printk("USB: hmc %d", config->hmc_mode);
if (config->pins[0])
printk(", usb0 %d wires%s", config->pins[0],
is_usb0_device(config) ? " (dev)" : "");
if (config->pins[1])
printk(", usb1 %d wires", config->pins[1]);
if (config->pins[2])
printk(", usb2 %d wires", config->pins[2]);
printk("\n");
/* use DPLL for 48 MHz function clock */
pr_debug("APLL %04x DPLL %04x REQ %04x\n", omap_readw(ULPD_APLL_CTRL),
omap_readw(ULPD_DPLL_CTRL), omap_readw(ULPD_SOFT_REQ));
w = omap_readw(ULPD_APLL_CTRL);
w &= ~APLL_NDPLL_SWITCH;
omap_writew(w, ULPD_APLL_CTRL);
w = omap_readw(ULPD_DPLL_CTRL);
w |= DPLL_IOB | DPLL_PLL_ENABLE;
omap_writew(w, ULPD_DPLL_CTRL);
w = omap_readw(ULPD_SOFT_REQ);
w |= SOFT_UDC_REQ | SOFT_DPLL_REQ;
omap_writew(w, ULPD_SOFT_REQ);
while (!(omap_readw(ULPD_DPLL_CTRL) & DPLL_LOCK))
cpu_relax();
#ifdef CONFIG_USB_GADGET_OMAP
if (config->register_dev) {
int status;
udc_device.dev.platform_data = config;
status = platform_device_register(&udc_device);
if (status)
pr_debug("can't register UDC device, %d\n", status);
/* udc driver gates 48MHz by D+ pullup */
}
#endif
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
if (config->register_host) {
int status;
ohci_device.dev.platform_data = config;
status = platform_device_register(&ohci_device);
if (status)
pr_debug("can't register OHCI device, %d\n", status);
/* hcd explicitly gates 48MHz */
}
#endif
}
#else
static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
#endif
/*-------------------------------------------------------------------------*/
void __init omap_usb_init(struct omap_usb_config *pdata)
{
pdata->usb0_init = omap_usb0_init;
pdata->usb1_init = omap_usb1_init;
pdata->usb2_init = omap_usb2_init;
udc_device_init(pdata);
ohci_device_init(pdata);
otg_device_init(pdata);
if (cpu_is_omap7xx() || cpu_is_omap16xx())
omap_otg_init(pdata);
else if (cpu_is_omap15xx())
omap_1510_usb_init(pdata);
else
printk(KERN_ERR "USB: No init for your chip yet\n");
}
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment