Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 - new driver to support GMT G762/G763 pwm fan controllers
 - add support for DS1631, DS1721, and DS1731 to ds1621 driver
 - remove detect function from ds1621 driver as unreliable
 - bug fixes in nct6775, iio_hwmon, and adm1021 drivers
 - remove redundant platform_set_drvdata in various drivers
 - add device tree support to ina2xx driver

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (ds1621) Fix temperature rounding operations
  hwmon: (nct6775) Drop unsupported fan alarm attributes for NCT6775
  hwmon: (nct6775) Fix temperature alarm attributes
  Add support for GMT G762/G763 PWM fan controllers
  hwmon: (ina2xx) Add device tree support to pass the shunt resistor
  hwmon: (ds1621) Update documentation
  hwmon: (ds1621) Add DS1731 chip support to ds1621 driver
  hwmon: (iio_hwmon) add alias table
  hwmon: (adm1021) Do not create min sysfs attributes for LM84
  hwmon: (ds1621) Remove detect function
  hwmon: (ds1621) Add ds1631 chip support to ds1621 driver and documentation
  hwmon: (ds1621) Add ds1721 update interval sysfs attribute
  hwmon: (ds1621) Add ds1721 chip support
  hwmon: (w83627ehf) Remove redundant platform_set_drvdata()
  hwmon: (ntc_thermistor) Remove redundant platform_set_drvdata()
  hwmon: (i5k_amb) Remove redundant platform_set_drvdata()
  hwmon: (coretemp) Remove redundant platform_set_drvdata()
  hwmon: (abituguru3) Remove redundant platform_set_drvdata()

Documentation/devicetree/bindings/hwmon/g762.txt

+GMT G762/G763 PWM Fan controller
+
+Required node properties:
+
+ - "compatible": must be either "gmt,g762" or "gmt,g763"
+ - "reg": I2C bus address of the device
+ - "clocks": a fixed clock providing input clock frequency
+	     on CLK pin of the chip.
+
+Optional properties:
+
+ - "fan_startv": fan startup voltage. Accepted values are 0, 1, 2 and 3.
+	       The higher the more.
+
+ - "pwm_polarity": pwm polarity. Accepted values are 0 (positive duty)
+	       and 1 (negative duty).
+
+ - "fan_gear_mode": fan gear mode. Supported values are 0, 1 and 2.
+
+If an optional property is not set in .dts file, then current value is kept
+unmodified (e.g. u-boot installed value).
+
+Additional information on operational parameters for the device is available
+in Documentation/hwmon/g762. A detailed datasheet for the device is available
+at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf.
+
+Example g762 node:
+
+   clocks {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	g762_clk: fixedclk {
+		 compatible = "fixed-clock";
+		 #clock-cells = <0>;
+		 clock-frequency = <8192>;
+	}
+   }
+
+   g762: g762@3e {
+	compatible = "gmt,g762";
+	reg = <0x3e>;
+	clocks = <&g762_clk>
+	fan_gear_mode = <0>; /* chip default */
+	fan_startv = <1>;    /* chip default */
+	pwm_polarity = <0>;  /* chip default */
+   };

Documentation/devicetree/bindings/i2c/ina2xx.txt

+ina2xx properties
+
+Required properties:
+- compatible: Must be one of the following:
+	- "ti,ina219" for ina219
+	- "ti,ina220" for ina220
+	- "ti,ina226" for ina226
+	- "ti,ina230" for ina230
+- reg: I2C address
+
+Optional properties:
+
+- shunt-resistor
+	Shunt resistor value in micro-Ohm
+
+Example:
+
+ina220@44 {
+	compatible = "ti,ina220";
+	reg = <0x44>;
+	shunt-resistor = <1000>;
+};

Documentation/hwmon/ds1621

@@ -2,16 +2,30 @@ Kernel driver ds1621
 ====================
 
 Supported chips:
-  * Dallas Semiconductor DS1621
+  * Dallas Semiconductor / Maxim Integrated DS1621
     Prefix: 'ds1621'
-    Addresses scanned: I2C 0x48 - 0x4f
-    Datasheet: Publicly available at the Dallas Semiconductor website
-               http://www.dalsemi.com/
+    Addresses scanned: none
+    Datasheet: Publicly available from www.maximintegrated.com
+
   * Dallas Semiconductor DS1625
-    Prefix: 'ds1621'
-    Addresses scanned: I2C 0x48 - 0x4f
-    Datasheet: Publicly available at the Dallas Semiconductor website
-               http://www.dalsemi.com/
+    Prefix: 'ds1625'
+    Addresses scanned: none
+    Datasheet: Publicly available from www.datasheetarchive.com
+
+  * Maxim Integrated DS1631
+    Prefix: 'ds1631'
+    Addresses scanned: none
+    Datasheet: Publicly available from www.maximintegrated.com
+
+  * Maxim Integrated DS1721
+    Prefix: 'ds1721'
+    Addresses scanned: none
+    Datasheet: Publicly available from www.maximintegrated.com
+
+  * Maxim Integrated DS1731
+    Prefix: 'ds1731'
+    Addresses scanned: none
+    Datasheet: Publicly available from www.maximintegrated.com
 
 Authors:
         Christian W. Zuckschwerdt <zany@triq.net>
@@ -59,5 +73,115 @@ any of the limits have ever been met or exceeded since last power-up or
 reset. Be aware: When testing, it showed that the status of Tout can change
 with neither of the alarms set.
 
-Temperature conversion of the DS1621 takes up to 1000ms; internal access to
-non-volatile registers may last for 10ms or below.
+Since there is no version or vendor identification register, there is
+no unique identification for these devices. Therefore, explicit device
+instantiation is required for correct device identification and functionality
+(one device per address in this address range: 0x48..0x4f).
+
+The DS1625 is pin compatible and functionally equivalent with the DS1621,
+but the DS1621 is meant to replace it. The DS1631, DS1721, and DS1731 are
+also pin compatible with the DS1621 and provide multi-resolution support.
+
+Additionally, the DS1721 data sheet says the temperature flags (THF and TLF)
+are used internally, however, these flags do get set and cleared as the actual
+temperature crosses the min or max settings (which by default are set to 75
+and 80 degrees respectively).
+
+Temperature Conversion:
+-----------------------
+DS1621 - 750ms (older devices may take up to 1000ms)
+DS1625 - 500ms
+DS1631 - 93ms..750ms for 9..12 bits resolution, respectively.
+DS1721 - 93ms..750ms for 9..12 bits resolution, respectively.
+DS1731 - 93ms..750ms for 9..12 bits resolution, respectively.
+
+Note:
+On the DS1621, internal access to non-volatile registers may last for 10ms
+or less (unverified on the other devices).
+
+Temperature Accuracy:
+---------------------
+DS1621: +/- 0.5 degree Celsius (from 0 to +70 degrees)
+DS1625: +/- 0.5 degree Celsius (from 0 to +70 degrees)
+DS1631: +/- 0.5 degree Celsius (from 0 to +70 degrees)
+DS1721: +/- 1.0 degree Celsius (from -10 to +85 degrees)
+DS1731: +/- 1.0 degree Celsius (from -10 to +85 degrees)
+
+Note:
+Please refer to the device datasheets for accuracy at other temperatures.
+
+Temperature Resolution:
+-----------------------
+As mentioned above, the DS1631, DS1721, and DS1731 provide multi-resolution
+support, which is achieved via the R0 and R1 config register bits, where:
+
+R0..R1
+------
+ 0  0 => 9 bits, 0.5 degrees Celcius
+ 1  0 => 10 bits, 0.25 degrees Celcius
+ 0  1 => 11 bits, 0.125 degrees Celcius
+ 1  1 => 12 bits, 0.0625 degrees Celcius
+
+Note:
+At initial device power-on, the default resolution is set to 12-bits.
+
+The resolution mode for the DS1631, DS1721, or DS1731 can be changed from
+userspace, via the device 'update_interval' sysfs attribute. This attribute
+will normalize the range of input values to the device maximum resolution
+values defined in the datasheet as follows:
+
+Resolution    Conversion Time    Input Range
+ (C/LSB)       (msec)             (msec)
+------------------------------------------------
+0.5             93.75              0....94
+0.25            187.5              95...187
+0.125           375                188..375
+0.0625          750                376..infinity
+------------------------------------------------
+
+The following examples show how the 'update_interval' attribute can be
+used to change the conversion time:
+
+$ cat update_interval
+750
+$ cat temp1_input
+22062
+$
+$ echo 300 > update_interval
+$ cat update_interval
+375
+$ cat temp1_input
+22125
+$
+$ echo 150 > update_interval
+$ cat update_interval
+188
+$ cat temp1_input
+22250
+$
+$ echo 1 > update_interval
+$ cat update_interval
+94
+$ cat temp1_input
+22000
+$
+$ echo 1000 > update_interval
+$ cat update_interval
+750
+$ cat temp1_input
+22062
+$
+
+As shown, the ds1621 driver automatically adjusts the 'update_interval'
+user input, via a step function. Reading back the 'update_interval' value
+after a write operation provides the conversion time used by the device.
+
+Mathematically, the resolution can be derived from the conversion time
+via the following function:
+
+   g(x) = 0.5 * [minimum_conversion_time/x]
+
+where:
+ -> 'x' = the output from 'update_interval'
+ -> 'g(x)' = the resolution in degrees C per LSB.
+ -> 93.75ms = minimum conversion time

Documentation/hwmon/g762

+Kernel driver g762
+==================
+
+The GMT G762 Fan Speed PWM Controller is connected directly to a fan
+and performs closed-loop or open-loop control of the fan speed. Two
+modes - PWM or DC - are supported by the device.
+
+For additional information, a detailed datasheet is available at
+http://natisbad.org/NAS/ref/GMT_EDS-762_763-080710-0.2.pdf. sysfs
+bindings are described in Documentation/hwmon/sysfs-interface.
+
+The following entries are available to the user in a subdirectory of
+/sys/bus/i2c/drivers/g762/ to control the operation of the device.
+This can be done manually using the following entries but is usually
+done via a userland daemon like fancontrol.
+
+Note that those entries do not provide ways to setup the specific
+hardware characteristics of the system (reference clock, pulses per
+fan revolution, ...); Those can be modified via devicetree bindings
+documented in Documentation/devicetree/bindings/hwmon/g762.txt or
+using a specific platform_data structure in board initialization
+file (see include/linux/platform_data/g762.h).
+
+  fan1_target: set desired fan speed. This only makes sense in closed-loop
+            fan speed control (i.e. when pwm1_enable is set to 2).
+
+  fan1_input: provide current fan rotation value in RPM as reported by
+            the fan to the device.
+
+  fan1_div: fan clock divisor. Supported value are 1, 2, 4 and 8.
+
+  fan1_pulses: number of pulses per fan revolution. Supported values
+            are 2 and 4.
+
+  fan1_fault: reports fan failure, i.e. no transition on fan gear pin for
+            about 0.7s (if the fan is not voluntarily set off).
+
+  fan1_alarm: in closed-loop control mode, if fan RPM value is 25% out
+            of the programmed value for over 6 seconds 'fan1_alarm' is
+            set to 1.
+
+  pwm1_enable: set current fan speed control mode i.e. 1 for manual fan
+            speed control (open-loop) via pwm1 described below, 2 for
+            automatic fan speed control (closed-loop) via fan1_target
+            above.
+
+  pwm1_mode: set or get fan driving mode: 1 for PWM mode, 0 for DC mode.
+
+  pwm1: get or set PWM fan control value in open-loop mode. This is an
+            integer value between 0 and 255. 0 stops the fan, 255 makes
+            it run at full speed.
+
+Both in PWM mode ('pwm1_mode' set to 1) and DC mode ('pwm1_mode' set to 0),
+when current fan speed control mode is open-loop ('pwm1_enable' set to 1),
+the fan speed is programmed by setting a value between 0 and 255 via 'pwm1'
+entry (0 stops the fan, 255 makes it run at full speed). In closed-loop mode
+('pwm1_enable' set to 2), the expected rotation speed in RPM can be passed to
+the chip via 'fan1_target'. In closed-loop mode, the target speed is compared
+with current speed (available via 'fan1_input') by the device and a feedback
+is performed to match that target value. The fan speed value is computed
+based on the parameters associated with the physical characteristics of the
+system: a reference clock source frequency, a number of pulses per fan
+revolution, etc.
+
+Note that the driver will update its values at most once per second.

Documentation/hwmon/ina2xx

@@ -44,4 +44,6 @@ The INA226 monitors both a shunt voltage drop and bus supply voltage.
 The INA230 is a high or low side current shunt and power monitor with an I2C
 interface. The INA230 monitors both a shunt voltage drop and bus supply voltage.
 
-The shunt value in micro-ohms can be set via platform data.
+The shunt value in micro-ohms can be set via platform data or device tree.
+Please refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings
+if the device tree is used.

drivers/hwmon/Kconfig

@@ -348,11 +348,16 @@ config SENSORS_DS620
 	  will be called ds620.
 
 config SENSORS_DS1621
-	tristate "Dallas Semiconductor DS1621 and DS1625"
+	tristate "Dallas Semiconductor DS1621 and compatibles"
 	depends on I2C
 	help
-	  If you say yes here you get support for Dallas Semiconductor
-	  DS1621 and DS1625 sensor chips.
+	  If you say yes here you get support for Dallas Semiconductor/Maxim
+	  Integrated DS1621 sensor chips and compatible models including:
+
+	  - Dallas Semiconductor DS1625
+	  - Maxim Integrated DS1631
+	  - Maxim Integrated DS1721
+	  - Maxim Integrated DS1731
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called ds1621.
@@ -456,6 +461,16 @@ config SENSORS_G760A
 	  This driver can also be built as a module.  If so, the module
 	  will be called g760a.
 
+config SENSORS_G762
+	tristate "GMT G762 and G763"
+	depends on I2C
+	help
+	  If you say yes here you get support for Global Mixed-mode
+	  Technology Inc G762 and G763 fan speed PWM controller chips.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called g762.
+
 config SENSORS_GL518SM
 	tristate "Genesys Logic GL518SM"
 	depends on I2C

drivers/hwmon/Makefile

@@ -60,6 +60,7 @@ obj-$(CONFIG_SENSORS_F75375S)	+= f75375s.o
 obj-$(CONFIG_SENSORS_FAM15H_POWER) += fam15h_power.o
 obj-$(CONFIG_SENSORS_FSCHMD)	+= fschmd.o
 obj-$(CONFIG_SENSORS_G760A)	+= g760a.o
+obj-$(CONFIG_SENSORS_G762)	+= g762.o
 obj-$(CONFIG_SENSORS_GL518SM)	+= gl518sm.o
 obj-$(CONFIG_SENSORS_GL520SM)	+= gl520sm.o
 obj-$(CONFIG_SENSORS_GPIO_FAN)	+= gpio-fan.o

drivers/hwmon/abituguru3.c

@@ -1079,7 +1079,6 @@ static int abituguru3_remove(struct platform_device *pdev)
 	int i;
 	struct abituguru3_data *data = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	hwmon_device_unregister(data->hwmon_dev);
 	for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
 		device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);

drivers/hwmon/adm1021.c

@@ -284,15 +284,11 @@ static DEVICE_ATTR(low_power, S_IWUSR | S_IRUGO, show_low_power, set_low_power);
 
 static struct attribute *adm1021_attributes[] = {
 	&sensor_dev_attr_temp1_max.dev_attr.attr,
-	&sensor_dev_attr_temp1_min.dev_attr.attr,
 	&sensor_dev_attr_temp1_input.dev_attr.attr,
 	&sensor_dev_attr_temp2_max.dev_attr.attr,
-	&sensor_dev_attr_temp2_min.dev_attr.attr,
 	&sensor_dev_attr_temp2_input.dev_attr.attr,
 	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
-	&sensor_dev_attr_temp2_min_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp2_fault.dev_attr.attr,
 	&dev_attr_alarms.attr,
 	&dev_attr_low_power.attr,
@@ -303,6 +299,18 @@ static const struct attribute_group adm1021_group = {
 	.attrs = adm1021_attributes,
 };
 
+static struct attribute *adm1021_min_attributes[] = {
+	&sensor_dev_attr_temp1_min.dev_attr.attr,
+	&sensor_dev_attr_temp2_min.dev_attr.attr,
+	&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
+	&sensor_dev_attr_temp2_min_alarm.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group adm1021_min_group = {
+	.attrs = adm1021_min_attributes,
+};
+
 /* Return 0 if detection is successful, -ENODEV otherwise */
 static int adm1021_detect(struct i2c_client *client,
 			  struct i2c_board_info *info)
@@ -425,6 +433,12 @@ static int adm1021_probe(struct i2c_client *client,
 	if (err)
 		return err;
 
+	if (data->type != lm84) {
+		err = sysfs_create_group(&client->dev.kobj, &adm1021_min_group);
+		if (err)
+			goto error;
+	}
+
 	data->hwmon_dev = hwmon_device_register(&client->dev);
 	if (IS_ERR(data->hwmon_dev)) {
 		err = PTR_ERR(data->hwmon_dev);
@@ -434,6 +448,7 @@ static int adm1021_probe(struct i2c_client *client,
 	return 0;
 
 error:
+	sysfs_remove_group(&client->dev.kobj, &adm1021_min_group);
 	sysfs_remove_group(&client->dev.kobj, &adm1021_group);
 	return err;
 }
@@ -452,6 +467,7 @@ static int adm1021_remove(struct i2c_client *client)
 	struct adm1021_data *data = i2c_get_clientdata(client);
 
 	hwmon_device_unregister(data->hwmon_dev);
+	sysfs_remove_group(&client->dev.kobj, &adm1021_min_group);
 	sysfs_remove_group(&client->dev.kobj, &adm1021_group);
 
 	return 0;
@@ -477,9 +493,11 @@ static struct adm1021_data *adm1021_update_device(struct device *dev)
 			data->temp_max[i] = 1000 *
 				(s8) i2c_smbus_read_byte_data(
 					client, ADM1021_REG_TOS_R(i));
+			if (data->type != lm84) {
 				data->temp_min[i] = 1000 *
-				(s8) i2c_smbus_read_byte_data(
-					client, ADM1021_REG_THYST_R(i));
+				  (s8) i2c_smbus_read_byte_data(client,
+							ADM1021_REG_THYST_R(i));
+			}
 		}
 		data->alarms = i2c_smbus_read_byte_data(client,
 						ADM1021_REG_STATUS) & 0x7c;

drivers/hwmon/coretemp.c

@@ -578,7 +578,6 @@ static int coretemp_probe(struct platform_device *pdev)
 
 exit_name:
 	device_remove_file(&pdev->dev, &pdata->name_attr);
-	platform_set_drvdata(pdev, NULL);
 exit_free:
 	kfree(pdata);
 	return err;
@@ -595,7 +594,6 @@ static int coretemp_remove(struct platform_device *pdev)
 
 	device_remove_file(&pdev->dev, &pdata->name_attr);
 	hwmon_device_unregister(pdata->hwmon_dev);
-	platform_set_drvdata(pdev, NULL);
 	kfree(pdata);
 	return 0;
 }

drivers/hwmon/i5k_amb.c

@@ -556,7 +556,6 @@ static int i5k_amb_probe(struct platform_device *pdev)
 
 err_init_failed:
 	iounmap(data->amb_mmio);
-	platform_set_drvdata(pdev, NULL);
 err_map_failed:
 	release_mem_region(data->amb_base, data->amb_len);
 err:
@@ -576,7 +575,6 @@ static int i5k_amb_remove(struct platform_device *pdev)
 	kfree(data->attrs);
 	iounmap(data->amb_mmio);
 	release_mem_region(data->amb_base, data->amb_len);
-	platform_set_drvdata(pdev, NULL);
 	kfree(data);
 	return 0;
 }

drivers/hwmon/iio_hwmon.c

@@ -180,6 +180,7 @@ static struct of_device_id iio_hwmon_of_match[] = {
 	{ .compatible = "iio-hwmon", },
 	{ }
 };
+MODULE_DEVICE_TABLE(of, iio_hwmon_of_match);
 
 static struct platform_driver __refdata iio_hwmon_driver = {
 	.driver = {

drivers/hwmon/ina2xx.c

@@ -34,6 +34,7 @@
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 #include <linux/jiffies.h>
+#include <linux/of.h>
 
 #include <linux/platform_data/ina2xx.h>
 
@@ -221,6 +222,7 @@ static int ina2xx_probe(struct i2c_client *client,
 	struct ina2xx_data *data;
 	struct ina2xx_platform_data *pdata;
 	int ret;
+	u32 val;
 	long shunt = 10000; /* default shunt value 10mOhms */
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA))
@@ -234,6 +236,9 @@ static int ina2xx_probe(struct i2c_client *client,
 		pdata =
 		  (struct ina2xx_platform_data *)client->dev.platform_data;
 		shunt = pdata->shunt_uohms;
+	} else if (!of_property_read_u32(client->dev.of_node,
+				"shunt-resistor", &val)) {
+			shunt = val;
 	}
 
 	if (shunt <= 0)

drivers/hwmon/nct6775.c

@@ -199,7 +199,7 @@ static const s8 NCT6775_ALARM_BITS[] = {
 	0, 1, 2, 3, 8, 21, 20, 16,	/* in0.. in7 */
 	17, -1, -1, -1, -1, -1, -1,	/* in8..in14 */
 	-1,				/* unused */
-	6, 7, 11, 10, 23,		/* fan1..fan5 */
+	6, 7, 11, -1, -1,		/* fan1..fan5 */
 	-1, -1, -1,			/* unused */
 	4, 5, 13, -1, -1, -1,		/* temp1..temp6 */
 	12, -1 };			/* intrusion0, intrusion1 */
@@ -625,6 +625,7 @@ struct nct6775_data {
 	u8 has_fan_min;		/* some fans don't have min register */
 	bool has_fan_div;
 
+	u8 num_temp_alarms;	/* 2 or 3 */
 	u8 temp_fixed_num;	/* 3 or 6 */
 	u8 temp_type[NUM_TEMP_FIXED];
 	s8 temp_offset[NUM_TEMP_FIXED];
@@ -1193,6 +1194,42 @@ show_alarm(struct device *dev, struct device_attribute *attr, char *buf)
 		       (unsigned int)((data->alarms >> nr) & 0x01));
 }
 
+static int find_temp_source(struct nct6775_data *data, int index, int count)
+{
+	int source = data->temp_src[index];
+	int nr;
+
+	for (nr = 0; nr < count; nr++) {
+		int src;
+
+		src = nct6775_read_value(data,
+					 data->REG_TEMP_SOURCE[nr]) & 0x1f;
+		if (src == source)
+			return nr;
+	}
+	return -1;
+}
+
+static ssize_t
+show_temp_alarm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sensor_device_attribute *sattr = to_sensor_dev_attr(attr);
+	struct nct6775_data *data = nct6775_update_device(dev);
+	unsigned int alarm = 0;
+	int nr;
+
+	/*
+	 * For temperatures, there is no fixed mapping from registers to alarm
+	 * bits. Alarm bits are determined by the temperature source mapping.
+	 */
+	nr = find_temp_source(data, sattr->index, data->num_temp_alarms);
+	if (nr >= 0) {
+		int bit = data->ALARM_BITS[nr + TEMP_ALARM_BASE];
+		alarm = (data->alarms >> bit) & 0x01;
+	}
+	return sprintf(buf, "%u\n", alarm);
+}
+
 static SENSOR_DEVICE_ATTR_2(in0_input, S_IRUGO, show_in_reg, NULL, 0, 0);
 static SENSOR_DEVICE_ATTR_2(in1_input, S_IRUGO, show_in_reg, NULL, 1, 0);
 static SENSOR_DEVICE_ATTR_2(in2_input, S_IRUGO, show_in_reg, NULL, 2, 0);
@@ -1874,22 +1911,18 @@ static struct sensor_device_attribute sda_temp_type[] = {
 };
 
 static struct sensor_device_attribute sda_temp_alarm[] = {
-	SENSOR_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL,
-		    TEMP_ALARM_BASE),
-	SENSOR_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL,
-		    TEMP_ALARM_BASE + 1),
-	SENSOR_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL,
-		    TEMP_ALARM_BASE + 2),
-	SENSOR_ATTR(temp4_alarm, S_IRUGO, show_alarm, NULL,
-		    TEMP_ALARM_BASE + 3),
-	SENSOR_ATTR(temp5_alarm, S_IRUGO, show_alarm, NULL,
-		    TEMP_ALARM_BASE + 4),
-	SENSOR_ATTR(temp6_alarm, S_IRUGO, show_alarm, NULL,
-		    TEMP_ALARM_BASE + 5),
+	SENSOR_ATTR(temp1_alarm, S_IRUGO, show_temp_alarm, NULL, 0),
+	SENSOR_ATTR(temp2_alarm, S_IRUGO, show_temp_alarm, NULL, 1),
+	SENSOR_ATTR(temp3_alarm, S_IRUGO, show_temp_alarm, NULL, 2),
+	SENSOR_ATTR(temp4_alarm, S_IRUGO, show_temp_alarm, NULL, 3),
+	SENSOR_ATTR(temp5_alarm, S_IRUGO, show_temp_alarm, NULL, 4),
+	SENSOR_ATTR(temp6_alarm, S_IRUGO, show_temp_alarm, NULL, 5),
+	SENSOR_ATTR(temp7_alarm, S_IRUGO, show_temp_alarm, NULL, 6),
+	SENSOR_ATTR(temp8_alarm, S_IRUGO, show_temp_alarm, NULL, 7),
+	SENSOR_ATTR(temp9_alarm, S_IRUGO, show_temp_alarm, NULL, 8),
+	SENSOR_ATTR(temp10_alarm, S_IRUGO, show_temp_alarm, NULL, 9),
 };
 
-#define NUM_TEMP_ALARM	ARRAY_SIZE(sda_temp_alarm)
-
 static ssize_t
 show_pwm_mode(struct device *dev, struct device_attribute *attr, char *buf)
 {
@@ -3215,13 +3248,11 @@ static void nct6775_device_remove_files(struct device *dev)
 		device_remove_file(dev, &sda_temp_max[i].dev_attr);
 		device_remove_file(dev, &sda_temp_max_hyst[i].dev_attr);
 		device_remove_file(dev, &sda_temp_crit[i].dev_attr);
+		device_remove_file(dev, &sda_temp_alarm[i].dev_attr);
 		if (!(data->have_temp_fixed & (1 << i)))
 			continue;
 		device_remove_file(dev, &sda_temp_type[i].dev_attr);
 		device_remove_file(dev, &sda_temp_offset[i].dev_attr);
-		if (i >= NUM_TEMP_ALARM)
-			continue;
-		device_remove_file(dev, &sda_temp_alarm[i].dev_attr);
 	}
 
 	device_remove_file(dev, &sda_caseopen[0].dev_attr);
@@ -3419,6 +3450,7 @@ static int nct6775_probe(struct platform_device *pdev)
 		data->auto_pwm_num = 6;
 		data->has_fan_div = true;
 		data->temp_fixed_num = 3;
+		data->num_temp_alarms = 3;
 
 		data->ALARM_BITS = NCT6775_ALARM_BITS;
 
@@ -3483,6 +3515,7 @@ static int nct6775_probe(struct platform_device *pdev)
 		data->auto_pwm_num = 4;
 		data->has_fan_div = false;
 		data->temp_fixed_num = 3;
+		data->num_temp_alarms = 3;
 
 		data->ALARM_BITS = NCT6776_ALARM_BITS;
 
@@ -3547,6 +3580,7 @@ static int nct6775_probe(struct platform_device *pdev)
 		data->auto_pwm_num = 4;
 		data->has_fan_div = false;
 		data->temp_fixed_num = 6;
+		data->num_temp_alarms = 2;
 
 		data->ALARM_BITS = NCT6779_ALARM_BITS;
 
@@ -3843,10 +3877,12 @@ static int nct6775_probe(struct platform_device *pdev)
 						 &sda_fan_input[i].dev_attr);
 			if (err)
 				goto exit_remove;
+			if (data->ALARM_BITS[FAN_ALARM_BASE + i] >= 0) {
 				err = device_create_file(dev,
 						&sda_fan_alarm[i].dev_attr);
 				if (err)
 					goto exit_remove;
+			}
 			if (data->kind != nct6776 &&
 			    data->kind != nct6779) {
 				err = device_create_file(dev,
@@ -3897,6 +3933,12 @@ static int nct6775_probe(struct platform_device *pdev)
 			if (err)
 				goto exit_remove;
 		}
+		if (find_temp_source(data, i, data->num_temp_alarms) >= 0) {
+			err = device_create_file(dev,
+						 &sda_temp_alarm[i].dev_attr);
+			if (err)
+				goto exit_remove;
+		}
 		if (!(data->have_temp_fixed & (1 << i)))
 			continue;
 		err = device_create_file(dev, &sda_temp_type[i].dev_attr);
@@ -3905,12 +3947,6 @@ static int nct6775_probe(struct platform_device *pdev)
 		err = device_create_file(dev, &sda_temp_offset[i].dev_attr);
 		if (err)
 			goto exit_remove;
-		if (i >= NUM_TEMP_ALARM ||
-		    data->ALARM_BITS[TEMP_ALARM_BASE + i] < 0)
-			continue;
-		err = device_create_file(dev, &sda_temp_alarm[i].dev_attr);
-		if (err)
-			goto exit_remove;
 	}
 
 	for (i = 0; i < ARRAY_SIZE(sda_caseopen); i++) {

drivers/hwmon/ntc_thermistor.c

@@ -514,7 +514,6 @@ static int ntc_thermistor_remove(struct platform_device *pdev)
 	hwmon_device_unregister(data->hwmon_dev);
 	sysfs_remove_group(&data->dev->kobj, &ntc_attr_group);
 	ntc_iio_channel_release(pdata);
-	platform_set_drvdata(pdev, NULL);
 
 	return 0;
 }

drivers/hwmon/w83627ehf.c

@@ -2598,7 +2598,6 @@ static int w83627ehf_probe(struct platform_device *pdev)
 exit_remove:
 	w83627ehf_device_remove_files(dev);
 exit_release:
-	platform_set_drvdata(pdev, NULL);
 	release_region(res->start, IOREGION_LENGTH);
 exit:
 	return err;
@@ -2611,7 +2610,6 @@ static int w83627ehf_remove(struct platform_device *pdev)
 	hwmon_device_unregister(data->hwmon_dev);
 	w83627ehf_device_remove_files(&pdev->dev);
 	release_region(data->addr, IOREGION_LENGTH);
-	platform_set_drvdata(pdev, NULL);
 
 	return 0;
 }

include/linux/platform_data/g762.h

+/*
+ * Platform data structure for g762 fan controller driver
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#ifndef __LINUX_PLATFORM_DATA_G762_H__
+#define __LINUX_PLATFORM_DATA_G762_H__
+
+/*
+ * Following structure can be used to set g762 driver platform specific data
+ * during board init. Note that passing a sparse structure is possible but
+ * will result in non-specified attributes to be set to default value, hence
+ * overloading those installed during boot (e.g. by u-boot).
+ */
+
+struct g762_platform_data {
+	u32 fan_startv;
+	u32 fan_gear_mode;
+	u32 pwm_polarity;
+	u32 clk_freq;
+};
+
+#endif /* __LINUX_PLATFORM_DATA_G762_H__ */