ARM: dts: cm-t3x: add NAND support

CM-T3517, CM-T3530 and CM-T3730 features NAND storage chip connected to
GPMC bus.

Add GPMC DT entry into the root DT file omap3-cm-t3x.dtsi, common for
all three modules.

NAND timings are calculated to be safe for CM-T3x devices as it works
now in non DT boot (in this case the timings are updated by U-Boot).

Update GPMC ranges in boards DT files to include all connected devices.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/omap3-cm-t3x.dtsi

@@ -259,3 +259,61 @@ &mcbsp2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp2_pins>;
 };
+
+&gpmc {
+	ranges = <0 0 0x00000000 0x01000000>;
+
+	nand@0,0 {
+		reg = <0 0 4>;	/* CS0, offset 0, IO size 4 */
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		ti,nand-ecc-opt = "sw";
+
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <120>;
+		gpmc,cs-wr-off-ns = <120>;
+
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <120>;
+		gpmc,adv-wr-off-ns = <120>;
+
+		gpmc,we-on-ns = <6>;
+		gpmc,we-off-ns = <90>;
+
+		gpmc,oe-on-ns = <6>;
+		gpmc,oe-off-ns = <90>;
+
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,access-ns = <72>;
+		gpmc,cycle2cycle-delay-ns = <60>;
+
+		gpmc,rd-cycle-ns = <120>;
+		gpmc,wr-cycle-ns = <120>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "xloader";
+			reg = <0 0x80000>;
+		};
+		partition@0x80000 {
+			label = "uboot";
+			reg = <0x80000 0x1e0000>;
+		};
+		partition@0x260000 {
+			label = "uboot environment";
+			reg = <0x260000 0x40000>;
+		};
+		partition@0x2a0000 {
+			label = "linux";
+			reg = <0x2a0000 0x400000>;
+		};
+		partition@0x6a0000 {
+			label = "rootfs";
+			reg = <0x6a0000 0x1f880000>;
+		};
+	};
+};

arch/arm/boot/dts/omap3-cm-t3x30.dtsi

@@ -50,7 +50,8 @@ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0
 #include "omap-gpmc-smsc911x.dtsi"
 
 &gpmc {
-	ranges = <5 0 0x2c000000 0x01000000>;
+	ranges = <5 0 0x2c000000 0x01000000>, /* CM-T3x30 SMSC9x Eth */
+		 <0 0 0x00000000 0x01000000>; /* CM-T3x NAND */
 
 	smsc1: ethernet@gpmc {
 		compatible = "smsc,lan9221", "smsc,lan9115";

arch/arm/boot/dts/omap3-sbc-t3517.dts

@@ -69,3 +69,7 @@ dpi_out: endpoint {
 	};
 };
 
+&gpmc {
+	ranges = <4 0 0x2d000000 0x01000000>,	/* SB-T35 SMSC9x Eth */
+		 <0 0 0x00000000 0x01000000>;	/* CM-T3x NAND */
+};

arch/arm/boot/dts/omap3-sbc-t3530.dts

@@ -26,14 +26,10 @@ OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35
 	};
 };
 
-/*
- * The following ranges correspond to SMSC9x eth chips on CM-T3530 CoM and
- * SB-T35 baseboard respectively.
- * This setting includes both chips in SBC-T3530 board device tree.
- */
 &gpmc {
-	ranges = <5 0 0x2c000000 0x01000000>,
-		 <4 0 0x2d000000 0x01000000>;
+	ranges = <5 0 0x2c000000 0x01000000>,	/* CM-T3x30 SMSC9x Eth */
+		 <4 0 0x2d000000 0x01000000>,	/* SB-T35 SMSC9x Eth */
+		 <0 0 0x00000000 0x01000000>;	/* CM-T3x NAND */
 };
 
 &mmc1 {

arch/arm/boot/dts/omap3-sbc-t3730.dts

@@ -27,8 +27,9 @@ OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35
 };
 
 &gpmc {
-	ranges = <5 0 0x2c000000 0x01000000>,
-		 <4 0 0x2d000000 0x01000000>;
+	ranges = <5 0 0x2c000000 0x01000000>,	/* CM-T3x30 SMSC9x Eth */
+		 <4 0 0x2d000000 0x01000000>,	/* SB-T35 SMSC9x Eth */
+		 <0 0 0x00000000 0x01000000>;	/* CM-T3x NAND */
 };
 
 &dss {