Commit e38da7d3 authored by Henning Schild's avatar Henning Schild Committed by Lee Jones

watchdog: simatic-ipc-wdt: convert to use P2SB accessor

Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.

Replace custom code by p2sb_bar() call.
Signed-off-by: default avatarHenning Schild <henning.schild@siemens.com>
Acked-by: default avatarGuenter Roeck <linux@roeck-us.net>
Signed-off-by: default avatarAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: default avatarLee Jones <lee@kernel.org>
parent 7b2db704
......@@ -1647,6 +1647,7 @@ config SIEMENS_SIMATIC_IPC_WDT
tristate "Siemens Simatic IPC Watchdog"
depends on SIEMENS_SIMATIC_IPC
select WATCHDOG_CORE
select P2SB
help
This driver adds support for several watchdogs found in Industrial
PCs from Siemens.
......
......@@ -16,6 +16,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/platform_data/x86/p2sb.h>
#include <linux/platform_data/x86/simatic-ipc-base.h>
#include <linux/platform_device.h>
#include <linux/sizes.h>
......@@ -54,9 +55,9 @@ static struct resource io_resource_trigger =
DEFINE_RES_IO_NAMED(WD_TRIGGER_IOADR, SZ_1,
KBUILD_MODNAME " WD_TRIGGER_IOADR");
/* the actual start will be discovered with pci, 0 is a placeholder */
/* the actual start will be discovered with p2sb, 0 is a placeholder */
static struct resource mem_resource =
DEFINE_RES_MEM_NAMED(0, SZ_4, "WD_RESET_BASE_ADR");
DEFINE_RES_MEM_NAMED(0, 0, "WD_RESET_BASE_ADR");
static u32 wd_timeout_table[] = {2, 4, 6, 8, 16, 32, 48, 64 };
static void __iomem *wd_reset_base_addr;
......@@ -150,6 +151,7 @@ static int simatic_ipc_wdt_probe(struct platform_device *pdev)
struct simatic_ipc_platform *plat = pdev->dev.platform_data;
struct device *dev = &pdev->dev;
struct resource *res;
int ret;
switch (plat->devmode) {
case SIMATIC_IPC_DEVICE_227E:
......@@ -190,15 +192,14 @@ static int simatic_ipc_wdt_probe(struct platform_device *pdev)
if (plat->devmode == SIMATIC_IPC_DEVICE_427E) {
res = &mem_resource;
/* get GPIO base from PCI */
res->start = simatic_ipc_get_membase0(PCI_DEVFN(0x1f, 1));
if (res->start == 0)
return -ENODEV;
ret = p2sb_bar(NULL, 0, res);
if (ret)
return ret;
/* do the final address calculation */
res->start = res->start + (GPIO_COMMUNITY0_PORT_ID << 16) +
PAD_CFG_DW0_GPP_A_23;
res->end += res->start;
res->end = res->start + SZ_4 - 1;
wd_reset_base_addr = devm_ioremap_resource(dev, res);
if (IS_ERR(wd_reset_base_addr))
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment