ath9k: Handle invalid RSSI

The combined RSSI can be invalid which is indicated by
the value -128. Use RX_FLAG_NO_SIGNAL_VAL for such cases.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/recv.c

@@ -885,29 +885,49 @@ static int ath9k_process_rate(struct ath_common *common,
 
 static void ath9k_process_rssi(struct ath_common *common,
 			       struct ieee80211_hw *hw,
-			       struct ath_rx_status *rx_stats)
+			       struct ath_rx_status *rx_stats,
+			       struct ieee80211_rx_status *rxs)
 {
 	struct ath_softc *sc = hw->priv;
 	struct ath_hw *ah = common->ah;
 	int last_rssi;
 	int rssi = rx_stats->rs_rssi;
 
-	if (!rx_stats->is_mybeacon ||
-	    ((ah->opmode != NL80211_IFTYPE_STATION) &&
-	     (ah->opmode != NL80211_IFTYPE_ADHOC)))
+	/*
+	 * RSSI is not available for subframes in an A-MPDU.
+	 */
+	if (rx_stats->rs_moreaggr) {
+		rxs->flag |= RX_FLAG_NO_SIGNAL_VAL;
 		return;
+	}
 
-	if (rx_stats->rs_rssi != ATH9K_RSSI_BAD && !rx_stats->rs_moreaggr)
-		ATH_RSSI_LPF(sc->last_rssi, rx_stats->rs_rssi);
+	/*
+	 * Check if the RSSI for the last subframe in an A-MPDU
+	 * or an unaggregated frame is valid.
+	 */
+	if (rx_stats->rs_rssi == ATH9K_RSSI_BAD) {
+		rxs->flag |= RX_FLAG_NO_SIGNAL_VAL;
+		return;
+	}
 
+	/*
+	 * Update Beacon RSSI, this is used by ANI.
+	 */
+	if (rx_stats->is_mybeacon &&
+	    ((ah->opmode == NL80211_IFTYPE_STATION) ||
+	     (ah->opmode == NL80211_IFTYPE_ADHOC))) {
+		ATH_RSSI_LPF(sc->last_rssi, rx_stats->rs_rssi);
 		last_rssi = sc->last_rssi;
+
 		if (likely(last_rssi != ATH_RSSI_DUMMY_MARKER))
 			rssi = ATH_EP_RND(last_rssi, ATH_RSSI_EP_MULTIPLIER);
 		if (rssi < 0)
 			rssi = 0;
 
-	/* Update Beacon RSSI, this is used by ANI. */
 		ah->stats.avgbrssi = rssi;
+	}
+
+	rxs->signal = ah->noise + rx_stats->rs_rssi;
 }
 
 static void ath9k_process_tsf(struct ath_rx_status *rs,
@@ -1149,15 +1169,12 @@ static int ath9k_rx_skb_preprocess(struct ath_softc *sc,
 		goto exit;
 	}
 
-	ath9k_process_rssi(common, hw, rx_stats);
+	ath9k_process_rssi(common, hw, rx_stats, rx_status);
 
 	rx_status->band = hw->conf.chandef.chan->band;
 	rx_status->freq = hw->conf.chandef.chan->center_freq;
-	rx_status->signal = ah->noise + rx_stats->rs_rssi;
 	rx_status->antenna = rx_stats->rs_antenna;
 	rx_status->flag |= RX_FLAG_MACTIME_END;
-	if (rx_stats->rs_moreaggr)
-		rx_status->flag |= RX_FLAG_NO_SIGNAL_VAL;
 
 #ifdef CONFIG_ATH9K_BTCOEX_SUPPORT
 	if (ieee80211_is_data_present(hdr->frame_control) &&