Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform updates from Arnd Bergmann:
 "These are updates for platform specific code on 32-bit ARM machines,
  essentially anything that can not (yet) be expressed using DT files.

  Noteworthy changes include:

   - Added support for the TI DRA71x family of SoCs in mach-omap2, this
     is an new variant of the the DRA72x/DRA74x automotive infotainment
     chips we already supported for a while.

   - Added support for the ST STM32F746 SoC, the first Cortex-M7 based
     microcontroller we support, related to the smaller STM32F4 family.

   - Renesas adds support for r8a7743 and r8a7745 in mach-shmobile, see
     http://elinux.org/RZ-G

   - SMP is now supported on the OX820 platform

   - A lot of code in mach-omap2 gets removed as a follow-up to removing
     support for board files in the previous release

   - Davinci has some new work to improve USB support

   - For i.MX, the performance monitor now supports profiling the memory
     controller using 'perf'"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (95 commits)
  ARM: davinci: da830-evm: use gpio descriptor for mmc pins
  ARM: davinci: da850-evm: use gpio descriptor for mmc pins
  ARM: davinci: hawk: use gpio descriptor for mmc pins
  ARM: ARTPEC-6: add select MFD_SYSCON to MACH_ARTPEC6
  ARM: davinci: da8xx: Fix ohci device name
  ARM: oxnas: Add OX820 config and makefile entry
  ARM: oxnas: Add OX820 SMP support
  ARM: davinci: PM: fix build when da850 not compiled in
  ARM: orion5x: remove legacy support of ls-chl
  ARM: integrator: drop EBI access use syscon
  ARM: BCM5301X: Add back handler ignoring external imprecise aborts
  ARM: davinci: PM: support da8xx DT platforms
  ARM: davinci: PM: cleanup: remove references to pdata
  ARM: davinci: PM: rework init, remove platform device
  ARM: Kconfig: Introduce MACH_STM32F746 flag
  ARM: mach-stm32: Add a new SOC - STM32F746
  ARM: shmobile: document SK-RZG1E board
  ARM: shmobile: r8a7745: basic SoC support
  ARM: imx: mach-imx6ul: add imx6ull support
  ARM: zynq: Reserve correct amount of non-DMA RAM
  ...

Documentation/arm/stm32/overview.txt

@@ -5,7 +5,8 @@ Introduction
 ------------
 
   The STMicroelectronics family of Cortex-M based MCUs are supported by the
-  'STM32' platform of ARM Linux. Currently only the STM32F429 is supported.
+  'STM32' platform of ARM Linux. Currently only the STM32F429 (Cortex-M4)
+  and STM32F746 (Cortex-M7) are supported.
 
 
 Configuration

Documentation/arm/stm32/stm32f746-overview.txt

+			STM32F746 Overview
+			==================
+
+  Introduction
+  ------------
+	The STM32F746 is a Cortex-M7 MCU aimed at various applications.
+	It features:
+	- Cortex-M7 core running up to @216MHz
+	- 1MB internal flash, 320KBytes internal RAM (+4KB of backup SRAM)
+	- FMC controller to connect SDRAM, NOR and NAND memories
+	- Dual mode QSPI
+	- SD/MMC/SDIO support
+	- Ethernet controller
+	- USB OTFG FS & HS controllers
+	- I2C, SPI, CAN busses support
+	- Several 16 & 32 bits general purpose timers
+	- Serial Audio interface
+	- LCD controller
+	- HDMI-CEC
+	- SPDIFRX
+
+  Resources
+  ---------
+	Datasheet and reference manual are publicly available on ST website:
+	- http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32f7-series/stm32f7x6/stm32f746ng.html
+
+  Document Author
+  ---------------
+	Alexandre Torgue <alexandre.torgue@st.com>
+
+
+
+
+

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -86,6 +86,9 @@ SoCs:
 - DRA722
   compatible = "ti,dra722", "ti,dra72", "ti,dra7"
 
+- DRA718
+  compatible = "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7"
+
 - AM5728
   compatible = "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7"
 
@@ -181,6 +184,9 @@ Boards:
 - DRA722 EVM: Software Development Board for DRA722
   compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7"
 
+- DRA718 EVM: Software Development Board for DRA718
+  compatible = "ti,dra718-evm", "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7"
+
 - DM3730 Logic PD Torpedo + Wireless: Commercial System on Module with WiFi and Bluetooth
   compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"
 

Documentation/devicetree/bindings/arm/shmobile.txt

@@ -13,6 +13,10 @@ SoCs:
     compatible = "renesas,r8a73a4"
   - R-Mobile A1 (R8A77400)
     compatible = "renesas,r8a7740"
+  - RZ/G1M (R8A77430)
+    compatible = "renesas,r8a7743"
+  - RZ/G1E (R8A77450)
+    compatible = "renesas,r8a7745"
   - R-Car M1A (R8A77781)
     compatible = "renesas,r8a7778"
   - R-Car H1 (R8A77790)
@@ -35,7 +39,7 @@ SoCs:
 
 Boards:
 
-  - Alt
+  - Alt (RTP0RC7794SEB00010S)
     compatible = "renesas,alt", "renesas,r8a7794"
   - APE6-EVM
     compatible = "renesas,ape6evm", "renesas,r8a73a4"
@@ -47,7 +51,7 @@ Boards:
     compatible = "renesas,bockw", "renesas,r8a7778"
   - Genmai (RTK772100BC00000BR)
     compatible = "renesas,genmai", "renesas,r7s72100"
-  - Gose
+  - Gose (RTP0RC7793SEB00010S)
     compatible = "renesas,gose", "renesas,r8a7793"
   - H3ULCB (RTP0RC7795SKB00010S)
     compatible = "renesas,h3ulcb", "renesas,r8a7795";
@@ -61,7 +65,7 @@ Boards:
     compatible = "renesas,kzm9g", "renesas,sh73a0"
   - Lager (RTP0RC7790SEB00010S)
     compatible = "renesas,lager", "renesas,r8a7790"
-  - Marzen
+  - Marzen (R0P7779A00010S)
     compatible = "renesas,marzen", "renesas,r8a7779"
   - Porter (M2-LCDP)
     compatible = "renesas,porter", "renesas,r8a7791"
@@ -73,5 +77,9 @@ Boards:
     compatible = "renesas,salvator-x", "renesas,r8a7796";
   - SILK (RTP0RC7794LCB00011S)
     compatible = "renesas,silk", "renesas,r8a7794"
+  - SK-RZG1E (YR8A77450S000BE)
+    compatible = "renesas,sk-rzg1e", "renesas,r8a7745"
+  - SK-RZG1M (YR8A77430S000BE)
+    compatible = "renesas,sk-rzg1m", "renesas,r8a7743"
   - Wheat
     compatible = "renesas,wheat", "renesas,r8a7792"

arch/arm/Kconfig

@@ -888,6 +888,11 @@ config MACH_STM32F429
 	depends on ARCH_STM32
 	default y
 
+config MACH_STM32F746
+	bool "STMicrolectronics STM32F746"
+	depends on ARCH_STM32
+	default y
+
 config ARCH_MPS2
 	bool "ARM MPS2 platform"
 	depends on ARM_SINGLE_ARMV7M

arch/arm/Makefile

@@ -191,6 +191,7 @@ machine-$(CONFIG_ARCH_MXS)		+= mxs
 machine-$(CONFIG_ARCH_NETX)		+= netx
 machine-$(CONFIG_ARCH_NOMADIK)		+= nomadik
 machine-$(CONFIG_ARCH_NSPIRE)		+= nspire
+machine-$(CONFIG_ARCH_OXNAS)		+= oxnas
 machine-$(CONFIG_ARCH_OMAP1)		+= omap1
 machine-$(CONFIG_ARCH_OMAP2PLUS)	+= omap2
 machine-$(CONFIG_ARCH_ORION5X)		+= orion5x

arch/arm/mach-artpec/Kconfig

@@ -14,6 +14,7 @@ config MACH_ARTPEC6
 	select HAVE_ARM_ARCH_TIMER
 	select HAVE_ARM_SCU
 	select HAVE_ARM_TWD if SMP
+	select MFD_SYSCON
 	help
 	  Support for Axis ARTPEC-6 ARM Cortex A9 Platform
 

arch/arm/mach-bcm/bcm_5301x.c

@@ -9,14 +9,42 @@
 #include <asm/hardware/cache-l2x0.h>
 
 #include <asm/mach/arch.h>
+#include <asm/siginfo.h>
+#include <asm/signal.h>
+
+#define FSR_EXTERNAL		(1 << 12)
+#define FSR_READ		(0 << 10)
+#define FSR_IMPRECISE		0x0406
 
 static const char *const bcm5301x_dt_compat[] __initconst = {
 	"brcm,bcm4708",
 	NULL,
 };
 
+static int bcm5301x_abort_handler(unsigned long addr, unsigned int fsr,
+				  struct pt_regs *regs)
+{
+	/*
+	 * We want to ignore aborts forwarded from the PCIe bus that are
+	 * expected and shouldn't really be passed by the PCIe controller.
+	 * The biggest disadvantage is the same FSR code may be reported when
+	 * reading non-existing APB register and we shouldn't ignore that.
+	 */
+	if (fsr == (FSR_EXTERNAL | FSR_READ | FSR_IMPRECISE))
+		return 0;
+
+	return 1;
+}
+
+static void __init bcm5301x_init_early(void)
+{
+	hook_fault_code(16 + 6, bcm5301x_abort_handler, SIGBUS, BUS_OBJERR,
+			"imprecise external abort");
+}
+
 DT_MACHINE_START(BCM5301X, "BCM5301X")
 	.l2c_aux_val	= 0,
 	.l2c_aux_mask	= ~0,
 	.dt_compat	= bcm5301x_dt_compat,
+	.init_early	= bcm5301x_init_early,
 MACHINE_END

arch/arm/mach-davinci/Makefile

@@ -36,5 +36,7 @@ obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD)	+= board-omapl138-hawk.o
 
 # Power Management
 obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o
-obj-$(CONFIG_SUSPEND)			+= pm.o sleep.o
 obj-$(CONFIG_HAVE_CLK)			+= pm_domain.o
+ifeq ($(CONFIG_SUSPEND),y)
+obj-$(CONFIG_ARCH_DAVINCI_DA850)	+= pm.o sleep.o
+endif

arch/arm/mach-davinci/board-da830-evm.c

@@ -14,6 +14,7 @@
 #include <linux/console.h>
 #include <linux/interrupt.h>
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
 #include <linux/i2c/pcf857x.h>
@@ -27,6 +28,7 @@
 #include <linux/platform_data/mtd-davinci-aemif.h>
 #include <linux/platform_data/spi-davinci.h>
 #include <linux/platform_data/usb-davinci.h>
+#include <linux/regulator/machine.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -106,43 +108,24 @@ static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id)
 
 static __init void da830_evm_usb_init(void)
 {
-	u32 cfgchip2;
 	int ret;
 
-	/*
-	 * Set up USB clock/mode in the CFGCHIP2 register.
-	 * FYI:  CFGCHIP2 is 0x0000ef00 initially.
-	 */
-	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
-	/* USB2.0 PHY reference clock is 24 MHz */
-	cfgchip2 &= ~CFGCHIP2_REFFREQ;
-	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
-
-	/*
-	 * Select internal reference clock for USB 2.0 PHY
-	 * and use it as a clock source for USB 1.1 PHY
-	 * (this is the default setting anyway).
-	 */
-	cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
-	cfgchip2 |=  CFGCHIP2_USB2PHYCLKMUX;
+	/* USB_REFCLKIN is not used. */
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 2.0 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
-	/*
-	 * We have to override VBUS/ID signals when MUSB is configured into the
-	 * host-only mode -- ID pin will float if no cable is connected, so the
-	 * controller won't be able to drive VBUS thinking that it's a B-device.
-	 * Otherwise, we want to use the OTG mode and enable VBUS comparators.
-	 */
-	cfgchip2 &= ~CFGCHIP2_OTGMODE;
-#ifdef	CONFIG_USB_MUSB_HOST
-	cfgchip2 |=  CFGCHIP2_FORCE_HOST;
-#else
-	cfgchip2 |=  CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN;
-#endif
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 1.1 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
-	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+	ret = da8xx_register_usb_phy();
+	if (ret)
+		pr_warn("%s: USB PHY registration failed: %d\n",
+			__func__, ret);
 
-	/* USB_REFCLKIN is not used. */
 	ret = davinci_cfg_reg(DA830_USB0_DRVVBUS);
 	if (ret)
 		pr_warn("%s: USB 2.0 PinMux setup failed: %d\n", __func__, ret);
@@ -222,22 +205,16 @@ static const short da830_evm_mmc_sd_pins[] = {
 	-1
 };
 
-#define DA830_MMCSD_WP_PIN		GPIO_TO_PIN(2, 1)
-#define DA830_MMCSD_CD_PIN		GPIO_TO_PIN(2, 2)
-
-static int da830_evm_mmc_get_ro(int index)
-{
-	return gpio_get_value(DA830_MMCSD_WP_PIN);
-}
-
-static int da830_evm_mmc_get_cd(int index)
-{
-	return !gpio_get_value(DA830_MMCSD_CD_PIN);
-}
+static struct gpiod_lookup_table mmc_gpios_table = {
+	.dev_id = "da830-mmc.0",
+	.table = {
+		/* gpio chip 1 contains gpio range 32-63 */
+		GPIO_LOOKUP("davinci_gpio.1", 2, "cd", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.1", 1, "wp", GPIO_ACTIVE_LOW),
+	},
+};
 
 static struct davinci_mmc_config da830_evm_mmc_config = {
-	.get_ro			= da830_evm_mmc_get_ro,
-	.get_cd			= da830_evm_mmc_get_cd,
 	.wires			= 8,
 	.max_freq		= 50000000,
 	.caps			= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
@@ -253,26 +230,12 @@ static inline void da830_evm_init_mmc(void)
 		return;
 	}
 
-	ret = gpio_request(DA830_MMCSD_WP_PIN, "MMC WP");
-	if (ret) {
-		pr_warn("%s: can not open GPIO %d\n",
-			__func__, DA830_MMCSD_WP_PIN);
-		return;
-	}
-	gpio_direction_input(DA830_MMCSD_WP_PIN);
-
-	ret = gpio_request(DA830_MMCSD_CD_PIN, "MMC CD\n");
-	if (ret) {
-		pr_warn("%s: can not open GPIO %d\n",
-			__func__, DA830_MMCSD_CD_PIN);
-		return;
-	}
-	gpio_direction_input(DA830_MMCSD_CD_PIN);
+	gpiod_add_lookup_table(&mmc_gpios_table);
 
 	ret = da8xx_register_mmcsd0(&da830_evm_mmc_config);
 	if (ret) {
 		pr_warn("%s: mmc/sd registration failed: %d\n", __func__, ret);
-		gpio_free(DA830_MMCSD_WP_PIN);
+		gpiod_remove_lookup_table(&mmc_gpios_table);
 	}
 }
 
@@ -588,6 +551,10 @@ static __init void da830_evm_init(void)
 	struct davinci_soc_info *soc_info = &davinci_soc_info;
 	int ret;
 
+	ret = da8xx_register_cfgchip();
+	if (ret)
+		pr_warn("%s: CFGCHIP registration failed: %d\n", __func__, ret);
+
 	ret = da830_register_gpio();
 	if (ret)
 		pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
@@ -647,6 +614,8 @@ static __init void da830_evm_init(void)
 	ret = da8xx_register_spi_bus(0, ARRAY_SIZE(da830evm_spi_info));
 	if (ret)
 		pr_warn("%s: spi 0 registration failed: %d\n", __func__, ret);
+
+	regulator_has_full_constraints();
 }
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE

arch/arm/mach-davinci/board-da850-evm.c

@@ -15,6 +15,7 @@
 #include <linux/delay.h>
 #include <linux/gpio.h>
 #include <linux/gpio_keys.h>
+#include <linux/gpio/machine.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/i2c.h>
@@ -56,9 +57,6 @@
 #define DA850_LCD_PWR_PIN		GPIO_TO_PIN(2, 8)
 #define DA850_LCD_BL_PIN		GPIO_TO_PIN(2, 15)
 
-#define DA850_MMCSD_CD_PIN		GPIO_TO_PIN(4, 0)
-#define DA850_MMCSD_WP_PIN		GPIO_TO_PIN(4, 1)
-
 #define DA850_MII_MDIO_CLKEN_PIN	GPIO_TO_PIN(2, 6)
 
 static struct mtd_partition da850evm_spiflash_part[] = {
@@ -196,18 +194,6 @@ static struct platform_device da850_evm_norflash_device = {
 	.resource	= da850_evm_norflash_resource,
 };
 
-static struct davinci_pm_config da850_pm_pdata = {
-	.sleepcount = 128,
-};
-
-static struct platform_device da850_pm_device = {
-	.name           = "pm-davinci",
-	.dev = {
-		.platform_data	= &da850_pm_pdata,
-	},
-	.id             = -1,
-};
-
 /* DA850/OMAP-L138 EVM includes a 512 MByte large-page NAND flash
  * (128K blocks). It may be used instead of the (default) SPI flash
  * to boot, using TI's tools to install the secondary boot loader
@@ -776,19 +762,16 @@ static const short da850_evm_mcasp_pins[] __initconst = {
 	-1
 };
 
-static int da850_evm_mmc_get_ro(int index)
-{
-	return gpio_get_value(DA850_MMCSD_WP_PIN);
-}
-
-static int da850_evm_mmc_get_cd(int index)
-{
-	return !gpio_get_value(DA850_MMCSD_CD_PIN);
-}
+static struct gpiod_lookup_table mmc_gpios_table = {
+	.dev_id = "da830-mmc.0",
+	.table = {
+		/* gpio chip 2 contains gpio range 64-95 */
+		GPIO_LOOKUP("davinci_gpio.2", 0, "cd", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.2", 1, "wp", GPIO_ACTIVE_LOW),
+	},
+};
 
 static struct davinci_mmc_config da850_mmc_config = {
-	.get_ro		= da850_evm_mmc_get_ro,
-	.get_cd		= da850_evm_mmc_get_cd,
 	.wires		= 4,
 	.max_freq	= 50000000,
 	.caps		= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
@@ -1345,6 +1328,10 @@ static __init void da850_evm_init(void)
 {
 	int ret;
 
+	ret = da8xx_register_cfgchip();
+	if (ret)
+		pr_warn("%s: CFGCHIP registration failed: %d\n", __func__, ret);
+
 	ret = da850_register_gpio();
 	if (ret)
 		pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
@@ -1379,17 +1366,7 @@ static __init void da850_evm_init(void)
 			pr_warn("%s: MMCSD0 mux setup failed: %d\n",
 				__func__, ret);
 
-		ret = gpio_request(DA850_MMCSD_CD_PIN, "MMC CD\n");
-		if (ret)
-			pr_warn("%s: can not open GPIO %d\n",
-				__func__, DA850_MMCSD_CD_PIN);
-		gpio_direction_input(DA850_MMCSD_CD_PIN);
-
-		ret = gpio_request(DA850_MMCSD_WP_PIN, "MMC WP\n");
-		if (ret)
-			pr_warn("%s: can not open GPIO %d\n",
-				__func__, DA850_MMCSD_WP_PIN);
-		gpio_direction_input(DA850_MMCSD_WP_PIN);
+		gpiod_add_lookup_table(&mmc_gpios_table);
 
 		ret = da8xx_register_mmcsd0(&da850_mmc_config);
 		if (ret)
@@ -1453,10 +1430,7 @@ static __init void da850_evm_init(void)
 	if (ret)
 		pr_warn("%s: cpuidle registration failed: %d\n", __func__, ret);
 
-	ret = da850_register_pm(&da850_pm_device);
-	if (ret)
-		pr_warn("%s: suspend registration failed: %d\n", __func__, ret);
-
+	davinci_pm_init();
 	da850_vpif_init();
 
 	ret = spi_register_board_info(da850evm_spi_info,

arch/arm/mach-davinci/board-mityomapl138.c

@@ -498,22 +498,14 @@ static void __init mityomapl138_config_emac(void)
 		pr_warn("emac registration failed: %d\n", ret);
 }
 
-static struct davinci_pm_config da850_pm_pdata = {
-	.sleepcount = 128,
-};
-
-static struct platform_device da850_pm_device = {
-	.name	= "pm-davinci",
-	.dev = {
-		.platform_data  = &da850_pm_pdata,
-	},
-	.id	= -1,
-};
-
 static void __init mityomapl138_init(void)
 {
 	int ret;
 
+	ret = da8xx_register_cfgchip();
+	if (ret)
+		pr_warn("%s: CFGCHIP registration failed: %d\n", __func__, ret);
+
 	/* for now, no special EDMA channels are reserved */
 	ret = da850_register_edma(NULL);
 	if (ret)
@@ -555,9 +547,7 @@ static void __init mityomapl138_init(void)
 	if (ret)
 		pr_warn("cpuidle registration failed: %d\n", ret);
 
-	ret = da850_register_pm(&da850_pm_device);
-	if (ret)
-		pr_warn("suspend registration failed: %d\n", ret);
+	davinci_pm_init();
 }
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE

arch/arm/mach-davinci/board-omapl138-hawk.c

@@ -13,7 +13,9 @@
 #include <linux/init.h>
 #include <linux/console.h>
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/platform_data/gpio-davinci.h>
+#include <linux/regulator/machine.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -24,8 +26,6 @@
 #include <mach/mux.h>
 
 #define HAWKBOARD_PHY_ID		"davinci_mdio-0:07"
-#define DA850_HAWK_MMCSD_CD_PIN		GPIO_TO_PIN(3, 12)
-#define DA850_HAWK_MMCSD_WP_PIN		GPIO_TO_PIN(3, 13)
 
 #define DA850_USB1_VBUS_PIN		GPIO_TO_PIN(2, 4)
 #define DA850_USB1_OC_PIN		GPIO_TO_PIN(6, 13)
@@ -122,19 +122,16 @@ static const short hawk_mmcsd0_pins[] = {
 	-1
 };
 
-static int da850_hawk_mmc_get_ro(int index)
-{
-	return gpio_get_value(DA850_HAWK_MMCSD_WP_PIN);
-}
-
-static int da850_hawk_mmc_get_cd(int index)
-{
-	return !gpio_get_value(DA850_HAWK_MMCSD_CD_PIN);
-}
+static struct gpiod_lookup_table mmc_gpios_table = {
+	.dev_id = "da830-mmc.0",
+	.table = {
+		/* CD: gpio3_12: gpio60: chip 1 contains gpio range 32-63*/
+		GPIO_LOOKUP("davinci_gpio.1", 28, "cd", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.1", 29, "wp", GPIO_ACTIVE_LOW),
+	},
+};
 
 static struct davinci_mmc_config da850_mmc_config = {
-	.get_ro		= da850_hawk_mmc_get_ro,
-	.get_cd		= da850_hawk_mmc_get_cd,
 	.wires		= 4,
 	.max_freq	= 50000000,
 	.caps		= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
@@ -150,21 +147,7 @@ static __init void omapl138_hawk_mmc_init(void)
 		return;
 	}
 
-	ret = gpio_request_one(DA850_HAWK_MMCSD_CD_PIN,
-			GPIOF_DIR_IN, "MMC CD");
-	if (ret < 0) {
-		pr_warn("%s: can not open GPIO %d\n",
-			__func__, DA850_HAWK_MMCSD_CD_PIN);
-		return;
-	}
-
-	ret = gpio_request_one(DA850_HAWK_MMCSD_WP_PIN,
-			GPIOF_DIR_IN, "MMC WP");
-	if (ret < 0) {
-		pr_warn("%s: can not open GPIO %d\n",
-			__func__, DA850_HAWK_MMCSD_WP_PIN);
-		goto mmc_setup_wp_fail;
-	}
+	gpiod_add_lookup_table(&mmc_gpios_table);
 
 	ret = da8xx_register_mmcsd0(&da850_mmc_config);
 	if (ret) {
@@ -175,9 +158,7 @@ static __init void omapl138_hawk_mmc_init(void)
 	return;
 
 mmc_setup_mmcsd_fail:
-	gpio_free(DA850_HAWK_MMCSD_WP_PIN);
-mmc_setup_wp_fail:
-	gpio_free(DA850_HAWK_MMCSD_CD_PIN);
+	gpiod_remove_lookup_table(&mmc_gpios_table);
 }
 
 static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id);
@@ -243,7 +224,6 @@ static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id)
 static __init void omapl138_hawk_usb_init(void)
 {
 	int ret;
-	u32 cfgchip2;
 
 	ret = davinci_cfg_reg_list(da850_hawk_usb11_pins);
 	if (ret) {
@@ -251,12 +231,20 @@ static __init void omapl138_hawk_usb_init(void)
 		return;
 	}
 
-	/* Setup the Ref. clock frequency for the HAWK at 24 MHz. */
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 2.0 PHY CLK registration failed: %d\n",
+			__func__, ret);
 
-	cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-	cfgchip2 &= ~CFGCHIP2_REFFREQ;
-	cfgchip2 |=  CFGCHIP2_REFFREQ_24MHZ;
-	__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: USB 1.1 PHY CLK registration failed: %d\n",
+			__func__, ret);
+
+	ret = da8xx_register_usb_phy();
+	if (ret)
+		pr_warn("%s: USB PHY registration failed: %d\n",
+			__func__, ret);
 
 	ret = gpio_request_one(DA850_USB1_VBUS_PIN,
 			GPIOF_DIR_OUT, "USB1 VBUS");
@@ -292,6 +280,10 @@ static __init void omapl138_hawk_init(void)
 {
 	int ret;
 
+	ret = da8xx_register_cfgchip();
+	if (ret)
+		pr_warn("%s: CFGCHIP registration failed: %d\n", __func__, ret);
+
 	ret = da850_register_gpio();
 	if (ret)
 		pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
@@ -317,6 +309,8 @@ static __init void omapl138_hawk_init(void)
 	if (ret)
 		pr_warn("%s: dsp/rproc registration failed: %d\n",
 			__func__, ret);
+
+	regulator_has_full_constraints();
 }
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE

arch/arm/mach-davinci/common.c

@@ -118,6 +118,5 @@ void __init davinci_common_init(struct davinci_soc_info *soc_info)
 void __init davinci_init_late(void)
 {
 	davinci_cpufreq_init();
-	davinci_pm_init();
 	davinci_clk_disable_unused();
 }

arch/arm/mach-davinci/da830.c

@@ -412,7 +412,7 @@ static struct clk_lookup da830_clks[] = {
 	CLK("davinci-mcasp.0",	NULL,		&mcasp0_clk),
 	CLK("davinci-mcasp.1",	NULL,		&mcasp1_clk),
 	CLK("davinci-mcasp.2",	NULL,		&mcasp2_clk),
-	CLK(NULL,		"usb20",	&usb20_clk),
+	CLK("musb-da8xx",	"usb20",	&usb20_clk),
 	CLK(NULL,		"aemif",	&aemif_clk),
 	CLK(NULL,		"aintc",	&aintc_clk),
 	CLK(NULL,		"secu_mgr",	&secu_mgr_clk),
@@ -420,7 +420,7 @@ static struct clk_lookup da830_clks[] = {
 	CLK("davinci_mdio.0",   "fck",          &emac_clk),
 	CLK(NULL,		"gpio",		&gpio_clk),
 	CLK("i2c_davinci.2",	NULL,		&i2c1_clk),
-	CLK(NULL,		"usb11",	&usb11_clk),
+	CLK("ohci-da8xx",	"usb11",	&usb11_clk),
 	CLK(NULL,		"emif3",	&emif3_clk),
 	CLK(NULL,		"arm",		&arm_clk),
 	CLK(NULL,		"rmii",		&rmii_clk),

arch/arm/mach-davinci/da850.c

@@ -538,8 +538,8 @@ static struct clk_lookup da850_clks[] = {
 	CLK("da830-mmc.1",	NULL,		&mmcsd1_clk),
 	CLK("ti-aemif",		NULL,		&aemif_clk),
 	CLK(NULL,		"aemif",	&aemif_clk),
-	CLK(NULL,		"usb11",	&usb11_clk),
-	CLK(NULL,		"usb20",	&usb20_clk),
+	CLK("ohci-da8xx",	"usb11",	&usb11_clk),
+	CLK("musb-da8xx",	"usb20",	&usb20_clk),
 	CLK("spi_davinci.0",	NULL,		&spi0_clk),
 	CLK("spi_davinci.1",	NULL,		&spi1_clk),
 	CLK("vpif",		NULL,		&vpif_clk),
@@ -1214,44 +1214,6 @@ static int da850_round_armrate(struct clk *clk, unsigned long rate)
 }
 #endif
 
-int __init da850_register_pm(struct platform_device *pdev)
-{
-	int ret;
-	struct davinci_pm_config *pdata = pdev->dev.platform_data;
-
-	ret = davinci_cfg_reg(DA850_RTC_ALARM);
-	if (ret)
-		return ret;
-
-	pdata->ddr2_ctlr_base = da8xx_get_mem_ctlr();
-	pdata->deepsleep_reg = DA8XX_SYSCFG1_VIRT(DA8XX_DEEPSLEEP_REG);
-	pdata->ddrpsc_num = DA8XX_LPSC1_EMIF3C;
-
-	pdata->cpupll_reg_base = ioremap(DA8XX_PLL0_BASE, SZ_4K);
-	if (!pdata->cpupll_reg_base)
-		return -ENOMEM;
-
-	pdata->ddrpll_reg_base = ioremap(DA850_PLL1_BASE, SZ_4K);
-	if (!pdata->ddrpll_reg_base) {
-		ret = -ENOMEM;
-		goto no_ddrpll_mem;
-	}
-
-	pdata->ddrpsc_reg_base = ioremap(DA8XX_PSC1_BASE, SZ_4K);
-	if (!pdata->ddrpsc_reg_base) {
-		ret = -ENOMEM;
-		goto no_ddrpsc_mem;
-	}
-
-	return platform_device_register(pdev);
-
-no_ddrpsc_mem:
-	iounmap(pdata->ddrpll_reg_base);
-no_ddrpll_mem:
-	iounmap(pdata->cpupll_reg_base);
-	return ret;
-}
-
 /* VPIF resource, platform data */
 static u64 da850_vpif_dma_mask = DMA_BIT_MASK(32);
 

arch/arm/mach-davinci/da8xx-dt.c

@@ -38,6 +38,10 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 		       NULL),
 	OF_DEV_AUXDATA("ti,da830-mcasp-audio", 0x01d00000, "davinci-mcasp.0", NULL),
 	OF_DEV_AUXDATA("ti,da850-aemif", 0x68000000, "ti-aemif", NULL),
+	OF_DEV_AUXDATA("ti,da850-tilcdc", 0x01e13000, "da8xx_lcdc.0", NULL),
+	OF_DEV_AUXDATA("ti,da830-ohci", 0x01e25000, "ohci-da8xx", NULL),
+	OF_DEV_AUXDATA("ti,da830-musb", 0x01e00000, "musb-da8xx", NULL),
+	OF_DEV_AUXDATA("ti,da830-usb-phy", 0x01c1417c, "da8xx-usb-phy", NULL),
 	{}
 };
 
@@ -45,7 +49,19 @@ static struct of_dev_auxdata da850_auxdata_lookup[] __initdata = {
 
 static void __init da850_init_machine(void)
 {
+	int ret;
+
+	ret = da8xx_register_usb20_phy_clk(false);
+	if (ret)
+		pr_warn("%s: registering USB 2.0 PHY clock failed: %d",
+			__func__, ret);
+	ret = da8xx_register_usb11_phy_clk(false);
+	if (ret)
+		pr_warn("%s: registering USB 1.1 PHY clock failed: %d",
+			__func__, ret);
+
 	of_platform_default_populate(NULL, da850_auxdata_lookup, NULL);
+	davinci_pm_init();
 }
 
 static const char *const da850_boards_compat[] __initconst = {

arch/arm/mach-davinci/devices-da8xx.c

@@ -11,6 +11,7 @@
  * (at your option) any later version.
  */
 #include <linux/init.h>
+#include <linux/platform_data/syscon.h>
 #include <linux/platform_device.h>
 #include <linux/dma-contiguous.h>
 #include <linux/serial_8250.h>
@@ -57,15 +58,6 @@
 #define DA8XX_EMAC_RAM_OFFSET		0x0000
 #define DA8XX_EMAC_CTRL_RAM_SIZE	SZ_8K
 
-#define DA8XX_DMA_SPI0_RX	EDMA_CTLR_CHAN(0, 14)
-#define DA8XX_DMA_SPI0_TX	EDMA_CTLR_CHAN(0, 15)
-#define DA8XX_DMA_MMCSD0_RX	EDMA_CTLR_CHAN(0, 16)
-#define DA8XX_DMA_MMCSD0_TX	EDMA_CTLR_CHAN(0, 17)
-#define DA8XX_DMA_SPI1_RX	EDMA_CTLR_CHAN(0, 18)
-#define DA8XX_DMA_SPI1_TX	EDMA_CTLR_CHAN(0, 19)
-#define DA850_DMA_MMCSD1_RX	EDMA_CTLR_CHAN(1, 28)
-#define DA850_DMA_MMCSD1_TX	EDMA_CTLR_CHAN(1, 29)
-
 void __iomem *da8xx_syscfg0_base;
 void __iomem *da8xx_syscfg1_base;
 
@@ -964,16 +956,6 @@ static struct resource da8xx_spi0_resources[] = {
 		.end	= IRQ_DA8XX_SPINT0,
 		.flags	= IORESOURCE_IRQ,
 	},
-	[2] = {
-		.start	= DA8XX_DMA_SPI0_RX,
-		.end	= DA8XX_DMA_SPI0_RX,
-		.flags	= IORESOURCE_DMA,
-	},
-	[3] = {
-		.start	= DA8XX_DMA_SPI0_TX,
-		.end	= DA8XX_DMA_SPI0_TX,
-		.flags	= IORESOURCE_DMA,
-	},
 };
 
 static struct resource da8xx_spi1_resources[] = {
@@ -987,16 +969,6 @@ static struct resource da8xx_spi1_resources[] = {
 		.end	= IRQ_DA8XX_SPINT1,
 		.flags	= IORESOURCE_IRQ,
 	},
-	[2] = {
-		.start	= DA8XX_DMA_SPI1_RX,
-		.end	= DA8XX_DMA_SPI1_RX,
-		.flags	= IORESOURCE_DMA,
-	},
-	[3] = {
-		.start	= DA8XX_DMA_SPI1_TX,
-		.end	= DA8XX_DMA_SPI1_TX,
-		.flags	= IORESOURCE_DMA,
-	},
 };
 
 static struct davinci_spi_platform_data da8xx_spi_pdata[] = {
@@ -1089,3 +1061,30 @@ int __init da850_register_sata(unsigned long refclkpn)
 	return platform_device_register(&da850_sata_device);
 }
 #endif
+
+static struct syscon_platform_data da8xx_cfgchip_platform_data = {
+	.label	= "cfgchip",
+};
+
+static struct resource da8xx_cfgchip_resources[] = {
+	{
+		.start	= DA8XX_SYSCFG0_BASE + DA8XX_CFGCHIP0_REG,
+		.end	= DA8XX_SYSCFG0_BASE + DA8XX_CFGCHIP4_REG + 3,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device da8xx_cfgchip_device = {
+	.name	= "syscon",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &da8xx_cfgchip_platform_data,
+	},
+	.num_resources	= ARRAY_SIZE(da8xx_cfgchip_resources),
+	.resource	= da8xx_cfgchip_resources,
+};
+
+int __init da8xx_register_cfgchip(void)
+{
+	return platform_device_register(&da8xx_cfgchip_device);
+}

arch/arm/mach-davinci/devices.c

@@ -36,9 +36,6 @@
 #define DM365_MMCSD0_BASE	     0x01D11000
 #define DM365_MMCSD1_BASE	     0x01D00000
 
-#define DAVINCI_DMA_MMCRXEVT	26
-#define DAVINCI_DMA_MMCTXEVT	27
-
 void __iomem  *davinci_sysmod_base;
 
 void davinci_map_sysmod(void)

arch/arm/mach-davinci/dm355.c

@@ -397,14 +397,6 @@ static struct resource dm355_spi0_resources[] = {
 		.start = IRQ_DM355_SPINT0_0,
 		.flags = IORESOURCE_IRQ,
 	},
-	{
-		.start = 17,
-		.flags = IORESOURCE_DMA,
-	},
-	{
-		.start = 16,
-		.flags = IORESOURCE_DMA,
-	},
 };
 
 static struct davinci_spi_platform_data dm355_spi0_pdata = {

arch/arm/mach-davinci/dm365.c

@@ -660,14 +660,6 @@ static struct resource dm365_spi0_resources[] = {
 		.start = IRQ_DM365_SPIINT0_0,
 		.flags = IORESOURCE_IRQ,
 	},
-	{
-		.start = 17,
-		.flags = IORESOURCE_DMA,
-	},
-	{
-		.start = 16,
-		.flags = IORESOURCE_DMA,
-	},
 };
 
 static struct platform_device dm365_spi0_device = {

arch/arm/mach-davinci/include/mach/da8xx.h

@@ -61,6 +61,7 @@ extern unsigned int da850_max_speed;
 #define DA8XX_CFGCHIP1_REG	0x180
 #define DA8XX_CFGCHIP2_REG	0x184
 #define DA8XX_CFGCHIP3_REG	0x188
+#define DA8XX_CFGCHIP4_REG	0x18c
 
 #define DA8XX_SYSCFG1_BASE	(IO_PHYS + 0x22C000)
 #define DA8XX_SYSCFG1_VIRT(x)	(da8xx_syscfg1_base + (x))
@@ -88,8 +89,12 @@ int da850_register_edma(struct edma_rsv_info *rsv[2]);
 int da8xx_register_i2c(int instance, struct davinci_i2c_platform_data *pdata);
 int da8xx_register_spi_bus(int instance, unsigned num_chipselect);
 int da8xx_register_watchdog(void);
+int da8xx_register_usb_phy(void);
 int da8xx_register_usb20(unsigned mA, unsigned potpgt);
 int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata);
+int da8xx_register_usb_refclkin(int rate);
+int da8xx_register_usb20_phy_clk(bool use_usb_refclkin);
+int da8xx_register_usb11_phy_clk(bool use_usb_refclkin);
 int da8xx_register_emac(void);
 int da8xx_register_uio_pruss(void);
 int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata);
@@ -101,7 +106,6 @@ int da8xx_register_gpio(void *pdata);
 int da850_register_cpufreq(char *async_clk);
 int da8xx_register_cpuidle(void);
 void __iomem *da8xx_get_mem_ctlr(void);
-int da850_register_pm(struct platform_device *pdev);
 int da850_register_sata(unsigned long refclkpn);
 int da850_register_vpif(void);
 int da850_register_vpif_display
@@ -113,6 +117,7 @@ void da8xx_rproc_reserve_cma(void);
 int da8xx_register_rproc(void);
 int da850_register_gpio(void);
 int da830_register_gpio(void);
+int da8xx_register_cfgchip(void);
 
 extern struct platform_device da8xx_serial_device[];
 extern struct emac_platform_data da8xx_emac_pdata;

arch/arm/mach-davinci/pm.c

@@ -21,15 +21,22 @@
 
 #include <mach/common.h>
 #include <mach/da8xx.h>
-#include "sram.h"
+#include <mach/mux.h>
 #include <mach/pm.h>
 
 #include "clock.h"
+#include "psc.h"
+#include "sram.h"
 
+#define DA850_PLL1_BASE		0x01e1a000
 #define DEEPSLEEP_SLEEPCOUNT_MASK	0xFFFF
+#define DEEPSLEEP_SLEEPCOUNT		128
 
 static void (*davinci_sram_suspend) (struct davinci_pm_config *);
-static struct davinci_pm_config *pdata;
+static struct davinci_pm_config pm_config = {
+	.sleepcount = DEEPSLEEP_SLEEPCOUNT,
+	.ddrpsc_num = DA8XX_LPSC1_EMIF3C,
+};
 
 static void davinci_sram_push(void *dest, void *src, unsigned int size)
 {
@@ -41,58 +48,58 @@ static void davinci_pm_suspend(void)
 {
 	unsigned val;
 
-	if (pdata->cpupll_reg_base != pdata->ddrpll_reg_base) {
+	if (pm_config.cpupll_reg_base != pm_config.ddrpll_reg_base) {
 
 		/* Switch CPU PLL to bypass mode */
-		val = __raw_readl(pdata->cpupll_reg_base + PLLCTL);
+		val = __raw_readl(pm_config.cpupll_reg_base + PLLCTL);
 		val &= ~(PLLCTL_PLLENSRC | PLLCTL_PLLEN);
-		__raw_writel(val, pdata->cpupll_reg_base + PLLCTL);
+		__raw_writel(val, pm_config.cpupll_reg_base + PLLCTL);
 
 		udelay(PLL_BYPASS_TIME);
 
 		/* Powerdown CPU PLL */
-		val = __raw_readl(pdata->cpupll_reg_base + PLLCTL);
+		val = __raw_readl(pm_config.cpupll_reg_base + PLLCTL);
 		val |= PLLCTL_PLLPWRDN;
-		__raw_writel(val, pdata->cpupll_reg_base + PLLCTL);
+		__raw_writel(val, pm_config.cpupll_reg_base + PLLCTL);
 	}
 
 	/* Configure sleep count in deep sleep register */
-	val = __raw_readl(pdata->deepsleep_reg);
+	val = __raw_readl(pm_config.deepsleep_reg);
 	val &= ~DEEPSLEEP_SLEEPCOUNT_MASK,
-	val |= pdata->sleepcount;
-	__raw_writel(val, pdata->deepsleep_reg);
+	val |= pm_config.sleepcount;
+	__raw_writel(val, pm_config.deepsleep_reg);
 
 	/* System goes to sleep in this call */
-	davinci_sram_suspend(pdata);
+	davinci_sram_suspend(&pm_config);
 
-	if (pdata->cpupll_reg_base != pdata->ddrpll_reg_base) {
+	if (pm_config.cpupll_reg_base != pm_config.ddrpll_reg_base) {
 
 		/* put CPU PLL in reset */
-		val = __raw_readl(pdata->cpupll_reg_base + PLLCTL);
+		val = __raw_readl(pm_config.cpupll_reg_base + PLLCTL);
 		val &= ~PLLCTL_PLLRST;
-		__raw_writel(val, pdata->cpupll_reg_base + PLLCTL);
+		__raw_writel(val, pm_config.cpupll_reg_base + PLLCTL);
 
 		/* put CPU PLL in power down */
-		val = __raw_readl(pdata->cpupll_reg_base + PLLCTL);
+		val = __raw_readl(pm_config.cpupll_reg_base + PLLCTL);
 		val &= ~PLLCTL_PLLPWRDN;
-		__raw_writel(val, pdata->cpupll_reg_base + PLLCTL);
+		__raw_writel(val, pm_config.cpupll_reg_base + PLLCTL);
 
 		/* wait for CPU PLL reset */
 		udelay(PLL_RESET_TIME);
 
 		/* bring CPU PLL out of reset */
-		val = __raw_readl(pdata->cpupll_reg_base + PLLCTL);
+		val = __raw_readl(pm_config.cpupll_reg_base + PLLCTL);
 		val |= PLLCTL_PLLRST;
-		__raw_writel(val, pdata->cpupll_reg_base + PLLCTL);
+		__raw_writel(val, pm_config.cpupll_reg_base + PLLCTL);
 
 		/* Wait for CPU PLL to lock */
 		udelay(PLL_LOCK_TIME);
 
 		/* Remove CPU PLL from bypass mode */
-		val = __raw_readl(pdata->cpupll_reg_base + PLLCTL);
+		val = __raw_readl(pm_config.cpupll_reg_base + PLLCTL);
 		val &= ~PLLCTL_PLLENSRC;
 		val |= PLLCTL_PLLEN;
-		__raw_writel(val, pdata->cpupll_reg_base + PLLCTL);
+		__raw_writel(val, pm_config.cpupll_reg_base + PLLCTL);
 	}
 }
 
@@ -117,17 +124,36 @@ static const struct platform_suspend_ops davinci_pm_ops = {
 	.valid		= suspend_valid_only_mem,
 };
 
-static int __init davinci_pm_probe(struct platform_device *pdev)
+int __init davinci_pm_init(void)
 {
-	pdata = pdev->dev.platform_data;
-	if (!pdata) {
-		dev_err(&pdev->dev, "cannot get platform data\n");
-		return -ENOENT;
+	int ret;
+
+	ret = davinci_cfg_reg(DA850_RTC_ALARM);
+	if (ret)
+		return ret;
+
+	pm_config.ddr2_ctlr_base = da8xx_get_mem_ctlr();
+	pm_config.deepsleep_reg = DA8XX_SYSCFG1_VIRT(DA8XX_DEEPSLEEP_REG);
+
+	pm_config.cpupll_reg_base = ioremap(DA8XX_PLL0_BASE, SZ_4K);
+	if (!pm_config.cpupll_reg_base)
+		return -ENOMEM;
+
+	pm_config.ddrpll_reg_base = ioremap(DA850_PLL1_BASE, SZ_4K);
+	if (!pm_config.ddrpll_reg_base) {
+		ret = -ENOMEM;
+		goto no_ddrpll_mem;
+	}
+
+	pm_config.ddrpsc_reg_base = ioremap(DA8XX_PSC1_BASE, SZ_4K);
+	if (!pm_config.ddrpsc_reg_base) {
+		ret = -ENOMEM;
+		goto no_ddrpsc_mem;
 	}
 
 	davinci_sram_suspend = sram_alloc(davinci_cpu_suspend_sz, NULL);
 	if (!davinci_sram_suspend) {
-		dev_err(&pdev->dev, "cannot allocate SRAM memory\n");
+		pr_err("PM: cannot allocate SRAM memory\n");
 		return -ENOMEM;
 	}
 
@@ -136,23 +162,9 @@ static int __init davinci_pm_probe(struct platform_device *pdev)
 
 	suspend_set_ops(&davinci_pm_ops);
 
-	return 0;
-}
-
-static int __exit davinci_pm_remove(struct platform_device *pdev)
-{
-	sram_free(davinci_sram_suspend, davinci_cpu_suspend_sz);
-	return 0;
-}
-
-static struct platform_driver davinci_pm_driver = {
-	.driver = {
-		.name	 = "pm-davinci",
-	},
-	.remove = __exit_p(davinci_pm_remove),
-};
-
-int __init davinci_pm_init(void)
-{
-	return platform_driver_probe(&davinci_pm_driver, davinci_pm_probe);
+no_ddrpsc_mem:
+	iounmap(pm_config.ddrpll_reg_base);
+no_ddrpll_mem:
+	iounmap(pm_config.cpupll_reg_base);
+	return ret;
 }

arch/arm/mach-davinci/usb-da8xx.c

 /*
  * DA8xx USB
  */
+#include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/dma-mapping.h>
 #include <linux/init.h>
+#include <linux/mfd/da8xx-cfgchip.h>
+#include <linux/phy/phy.h>
 #include <linux/platform_data/usb-davinci.h>
 #include <linux/platform_device.h>
 #include <linux/usb/musb.h>
 
+#include <mach/clock.h>
 #include <mach/common.h>
 #include <mach/cputype.h>
 #include <mach/da8xx.h>
 #include <mach/irqs.h>
 
+#include "clock.h"
+
 #define DA8XX_USB0_BASE		0x01e00000
 #define DA8XX_USB1_BASE		0x01e25000
 
-#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
+static struct platform_device da8xx_usb_phy = {
+	.name		= "da8xx-usb-phy",
+	.id		= -1,
+	.dev		= {
+		/*
+		 * Setting init_name so that clock lookup will work in
+		 * da8xx_register_usb11_phy_clk() even if this device is not
+		 * registered yet.
+		 */
+		.init_name	= "da8xx-usb-phy",
+	},
+};
+
+int __init da8xx_register_usb_phy(void)
+{
+	return platform_device_register(&da8xx_usb_phy);
+}
 
 static struct musb_hdrc_config musb_config = {
 	.multipoint	= true,
@@ -45,10 +68,15 @@ static struct resource da8xx_usb20_resources[] = {
 
 static u64 usb_dmamask = DMA_BIT_MASK(32);
 
-static struct platform_device usb_dev = {
+static struct platform_device da8xx_usb20_dev = {
 	.name		= "musb-da8xx",
 	.id             = -1,
 	.dev = {
+		/*
+		 * Setting init_name so that clock lookup will work in
+		 * usb20_phy_clk_enable() even if this device is not registered.
+		 */
+		.init_name		= "musb-da8xx",
 		.platform_data		= &usb_data,
 		.dma_mask		= &usb_dmamask,
 		.coherent_dma_mask      = DMA_BIT_MASK(32),
@@ -62,18 +90,9 @@ int __init da8xx_register_usb20(unsigned int mA, unsigned int potpgt)
 	usb_data.power	= mA > 510 ? 255 : mA / 2;
 	usb_data.potpgt = (potpgt + 1) / 2;
 
-	return platform_device_register(&usb_dev);
+	return platform_device_register(&da8xx_usb20_dev);
 }
 
-#else
-
-int __init da8xx_register_usb20(unsigned int mA, unsigned int potpgt)
-{
-	return 0;
-}
-
-#endif  /* CONFIG_USB_MUSB_HDRC */
-
 static struct resource da8xx_usb11_resources[] = {
 	[0] = {
 		.start	= DA8XX_USB1_BASE,
@@ -90,8 +109,8 @@ static struct resource da8xx_usb11_resources[] = {
 static u64 da8xx_usb11_dma_mask = DMA_BIT_MASK(32);
 
 static struct platform_device da8xx_usb11_device = {
-	.name		= "ohci",
-	.id		= 0,
+	.name		= "ohci-da8xx",
+	.id		= -1,
 	.dev = {
 		.dma_mask		= &da8xx_usb11_dma_mask,
 		.coherent_dma_mask	= DMA_BIT_MASK(32),
@@ -105,3 +124,236 @@ int __init da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata)
 	da8xx_usb11_device.dev.platform_data = pdata;
 	return platform_device_register(&da8xx_usb11_device);
 }
+
+static struct clk usb_refclkin = {
+	.name		= "usb_refclkin",
+	.set_rate	= davinci_simple_set_rate,
+};
+
+static struct clk_lookup usb_refclkin_lookup =
+	CLK(NULL, "usb_refclkin", &usb_refclkin);
+
+/**
+ * da8xx_register_usb_refclkin - register USB_REFCLKIN clock
+ *
+ * @rate: The clock rate in Hz
+ *
+ * This clock is only needed if the board provides an external USB_REFCLKIN
+ * signal, in which case it will be used as the parent of usb20_phy_clk and/or
+ * usb11_phy_clk.
+ */
+int __init da8xx_register_usb_refclkin(int rate)
+{
+	int ret;
+
+	usb_refclkin.rate = rate;
+	ret = clk_register(&usb_refclkin);
+	if (ret)
+		return ret;
+
+	clkdev_add(&usb_refclkin_lookup);
+
+	return 0;
+}
+
+static void usb20_phy_clk_enable(struct clk *clk)
+{
+	struct clk *usb20_clk;
+	int err;
+	u32 val;
+	u32 timeout = 500000; /* 500 msec */
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	usb20_clk = clk_get(&da8xx_usb20_dev.dev, "usb20");
+	if (IS_ERR(usb20_clk)) {
+		pr_err("could not get usb20 clk: %ld\n", PTR_ERR(usb20_clk));
+		return;
+	}
+
+	/* The USB 2.O PLL requires that the USB 2.O PSC is enabled as well. */
+	err = clk_prepare_enable(usb20_clk);
+	if (err) {
+		pr_err("failed to enable usb20 clk: %d\n", err);
+		clk_put(usb20_clk);
+		return;
+	}
+
+	/*
+	 * Turn on the USB 2.0 PHY, but just the PLL, and not OTG. The USB 1.1
+	 * host may use the PLL clock without USB 2.0 OTG being used.
+	 */
+	val &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN);
+	val |= CFGCHIP2_PHY_PLLON;
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	while (--timeout) {
+		val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+		if (val & CFGCHIP2_PHYCLKGD)
+			goto done;
+		udelay(1);
+	}
+
+	pr_err("Timeout waiting for USB 2.0 PHY clock good\n");
+done:
+	clk_disable_unprepare(usb20_clk);
+	clk_put(usb20_clk);
+}
+
+static void usb20_phy_clk_disable(struct clk *clk)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+	val |= CFGCHIP2_PHYPWRDN;
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+}
+
+static int usb20_phy_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/* Set the mux depending on the parent clock. */
+	if (parent == &usb_refclkin) {
+		val &= ~CFGCHIP2_USB2PHYCLKMUX;
+	} else if (strcmp(parent->name, "pll0_aux_clk") == 0) {
+		val |= CFGCHIP2_USB2PHYCLKMUX;
+	} else {
+		pr_err("Bad parent on USB 2.0 PHY clock\n");
+		return -EINVAL;
+	}
+
+	/* reference frequency also comes from parent clock */
+	val &= ~CFGCHIP2_REFFREQ_MASK;
+	switch (clk_get_rate(parent)) {
+	case 12000000:
+		val |= CFGCHIP2_REFFREQ_12MHZ;
+		break;
+	case 13000000:
+		val |= CFGCHIP2_REFFREQ_13MHZ;
+		break;
+	case 19200000:
+		val |= CFGCHIP2_REFFREQ_19_2MHZ;
+		break;
+	case 20000000:
+		val |= CFGCHIP2_REFFREQ_20MHZ;
+		break;
+	case 24000000:
+		val |= CFGCHIP2_REFFREQ_24MHZ;
+		break;
+	case 26000000:
+		val |= CFGCHIP2_REFFREQ_26MHZ;
+		break;
+	case 38400000:
+		val |= CFGCHIP2_REFFREQ_38_4MHZ;
+		break;
+	case 40000000:
+		val |= CFGCHIP2_REFFREQ_40MHZ;
+		break;
+	case 48000000:
+		val |= CFGCHIP2_REFFREQ_48MHZ;
+		break;
+	default:
+		pr_err("Bad parent clock rate on USB 2.0 PHY clock\n");
+		return -EINVAL;
+	}
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	return 0;
+}
+
+static struct clk usb20_phy_clk = {
+	.name		= "usb20_phy",
+	.clk_enable	= usb20_phy_clk_enable,
+	.clk_disable	= usb20_phy_clk_disable,
+	.set_parent	= usb20_phy_clk_set_parent,
+};
+
+static struct clk_lookup usb20_phy_clk_lookup =
+	CLK("da8xx-usb-phy", "usb20_phy", &usb20_phy_clk);
+
+/**
+ * da8xx_register_usb20_phy_clk - register USB0PHYCLKMUX clock
+ *
+ * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
+ *	or "pll0_aux" if false.
+ */
+int __init da8xx_register_usb20_phy_clk(bool use_usb_refclkin)
+{
+	struct clk *parent;
+	int ret = 0;
+
+	parent = clk_get(NULL, use_usb_refclkin ? "usb_refclkin" : "pll0_aux");
+	if (IS_ERR(parent))
+		return PTR_ERR(parent);
+
+	usb20_phy_clk.parent = parent;
+	ret = clk_register(&usb20_phy_clk);
+	if (!ret)
+		clkdev_add(&usb20_phy_clk_lookup);
+
+	clk_put(parent);
+
+	return ret;
+}
+
+static int usb11_phy_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	u32 val;
+
+	val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	/* Set the USB 1.1 PHY clock mux based on the parent clock. */
+	if (parent == &usb20_phy_clk) {
+		val &= ~CFGCHIP2_USB1PHYCLKMUX;
+	} else if (parent == &usb_refclkin) {
+		val |= CFGCHIP2_USB1PHYCLKMUX;
+	} else {
+		pr_err("Bad parent on USB 1.1 PHY clock\n");
+		return -EINVAL;
+	}
+
+	writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
+
+	return 0;
+}
+
+static struct clk usb11_phy_clk = {
+	.name		= "usb11_phy",
+	.set_parent	= usb11_phy_clk_set_parent,
+};
+
+static struct clk_lookup usb11_phy_clk_lookup =
+	CLK("da8xx-usb-phy", "usb11_phy", &usb11_phy_clk);
+
+/**
+ * da8xx_register_usb11_phy_clk - register USB1PHYCLKMUX clock
+ *
+ * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
+ *	or "usb20_phy" if false.
+ */
+int __init da8xx_register_usb11_phy_clk(bool use_usb_refclkin)
+{
+	struct clk *parent;
+	int ret = 0;
+
+	if (use_usb_refclkin)
+		parent = clk_get(NULL, "usb_refclkin");
+	else
+		parent = clk_get(&da8xx_usb_phy.dev, "usb20_phy");
+	if (IS_ERR(parent))
+		return PTR_ERR(parent);
+
+	usb11_phy_clk.parent = parent;
+	ret = clk_register(&usb11_phy_clk);
+	if (!ret)
+		clkdev_add(&usb11_phy_clk_lookup);
+
+	clk_put(parent);
+
+	return ret;
+}

arch/arm/mach-imx/Kconfig

@@ -557,7 +557,6 @@ config SOC_VF610
 	bool "Vybrid Family VF610 support"
 	select ARM_GIC if ARCH_MULTI_V7
 	select PINCTRL_VF610
-	select PL310_ERRATA_769419 if CACHE_L2X0
 
 	help
 	  This enables support for Freescale Vybrid VF610 processor.

arch/arm/mach-imx/mach-imx6ul.c

@@ -89,6 +89,7 @@ static void __init imx6ul_init_late(void)
 
 static const char * const imx6ul_dt_compat[] __initconst = {
 	"fsl,imx6ul",
+	"fsl,imx6ull",
 	NULL,
 };
 

arch/arm/mach-integrator/integrator_ap.c

@@ -27,6 +27,8 @@
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/termios.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -37,11 +39,8 @@
 #include "pci_v3.h"
 #include "lm.h"
 
-/* Base address to the AP system controller */
-void __iomem *ap_syscon_base;
-/* Base address to the external bus interface */
-static void __iomem *ebi_base;
-
+/* Regmap to the AP system controller */
+static struct regmap *ap_syscon_map;
 
 /*
  * All IO addresses are mapped onto VA 0xFFFx.xxxx, where x.xxxx
@@ -125,6 +124,7 @@ static void integrator_uart_set_mctrl(struct amba_device *dev,
 {
 	unsigned int ctrls = 0, ctrlc = 0, rts_mask, dtr_mask;
 	u32 phybase = dev->res.start;
+	int ret;
 
 	if (phybase == INTEGRATOR_UART0_BASE) {
 		/* UART0 */
@@ -146,8 +146,17 @@ static void integrator_uart_set_mctrl(struct amba_device *dev,
 	else
 		ctrls |= dtr_mask;
 
-	__raw_writel(ctrls, ap_syscon_base + INTEGRATOR_SC_CTRLS_OFFSET);
-	__raw_writel(ctrlc, ap_syscon_base + INTEGRATOR_SC_CTRLC_OFFSET);
+	ret = regmap_write(ap_syscon_map,
+			   INTEGRATOR_SC_CTRLS_OFFSET,
+			   ctrls);
+	if (ret)
+		pr_err("MODEM: unable to write PL010 UART CTRLS\n");
+
+	ret = regmap_write(ap_syscon_map,
+			   INTEGRATOR_SC_CTRLC_OFFSET,
+			   ctrlc);
+	if (ret)
+		pr_err("MODEM: unable to write PL010 UART CRTLC\n");
 }
 
 struct amba_pl010_data ap_uart_data = {
@@ -178,35 +187,32 @@ static const struct of_device_id ap_syscon_match[] = {
 	{ },
 };
 
-static const struct of_device_id ebi_match[] = {
-	{ .compatible = "arm,external-bus-interface"},
-	{ },
-};
-
 static void __init ap_init_of(void)
 {
-	unsigned long sc_dec;
+	u32 sc_dec;
 	struct device_node *syscon;
-	struct device_node *ebi;
+	int ret;
 	int i;
 
+	of_platform_default_populate(NULL, ap_auxdata_lookup, NULL);
+
 	syscon = of_find_matching_node(NULL, ap_syscon_match);
 	if (!syscon)
 		return;
-	ebi = of_find_matching_node(NULL, ebi_match);
-	if (!ebi)
+	ap_syscon_map = syscon_node_to_regmap(syscon);
+	if (IS_ERR(ap_syscon_map)) {
+		pr_crit("could not find Integrator/AP system controller\n");
 		return;
+	}
 
-	ap_syscon_base = of_iomap(syscon, 0);
-	if (!ap_syscon_base)
-		return;
-	ebi_base = of_iomap(ebi, 0);
-	if (!ebi_base)
+	ret = regmap_read(ap_syscon_map,
+			  INTEGRATOR_SC_DEC_OFFSET,
+			  &sc_dec);
+	if (ret) {
+		pr_crit("could not read from Integrator/AP syscon\n");
 		return;
+	}
 
-	of_platform_default_populate(NULL, ap_auxdata_lookup, NULL);
-
-	sc_dec = readl(ap_syscon_base + INTEGRATOR_SC_DEC_OFFSET);
 	for (i = 0; i < 4; i++) {
 		struct lm_device *lmdev;
 

arch/arm/mach-lpc32xx/clock.h

-/*
- * arch/arm/mach-lpc32xx/clock.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __LPC32XX_CLOCK_H
-#define __LPC32XX_CLOCK_H
-
-struct clk {
-	struct list_head node;
-	struct clk *parent;
-	u32 rate;
-	u32 usecount;
-
-	int (*set_rate) (struct clk *, unsigned long);
-	unsigned long (*round_rate) (struct clk *, unsigned long);
-	unsigned long (*get_rate) (struct clk *clk);
-	int (*enable) (struct clk *, int);
-
-	/* Register address and bit mask for simple clocks */
-	void __iomem *enable_reg;
-	u32 enable_mask;
-};
-
-#endif

arch/arm/mach-lpc32xx/common.h

@@ -24,7 +24,6 @@
 /*
  * Other arch specific structures and functions
  */
-extern void __init lpc32xx_init_irq(void);
 extern void __init lpc32xx_map_io(void);
 extern void __init lpc32xx_serial_init(void);
 

arch/arm/mach-lpc32xx/include/mach/irqs.h

-/*
- * arch/arm/mach-lpc32xx/include/mach/irqs.h
- *
- * Author: Kevin Wells <kevin.wells@nxp.com>
- *
- * Copyright (C) 2010 NXP Semiconductors
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARM_ARCH_IRQS_H
-#define __ASM_ARM_ARCH_IRQS_H
-
-#define LPC32XX_SIC1_IRQ(n)		(32 + (n))
-#define LPC32XX_SIC2_IRQ(n)		(64 + (n))
-
-/*
- * MIC interrupts
- */
-#define IRQ_LPC32XX_SUB1IRQ		0
-#define IRQ_LPC32XX_SUB2IRQ		1
-#define IRQ_LPC32XX_PWM3		3
-#define IRQ_LPC32XX_PWM4		4
-#define IRQ_LPC32XX_HSTIMER		5
-#define IRQ_LPC32XX_WATCH		6
-#define IRQ_LPC32XX_UART_IIR3		7
-#define IRQ_LPC32XX_UART_IIR4		8
-#define IRQ_LPC32XX_UART_IIR5		9
-#define IRQ_LPC32XX_UART_IIR6		10
-#define IRQ_LPC32XX_FLASH		11
-#define IRQ_LPC32XX_SD1			13
-#define IRQ_LPC32XX_LCD			14
-#define IRQ_LPC32XX_SD0			15
-#define IRQ_LPC32XX_TIMER0		16
-#define IRQ_LPC32XX_TIMER1		17
-#define IRQ_LPC32XX_TIMER2		18
-#define IRQ_LPC32XX_TIMER3		19
-#define IRQ_LPC32XX_SSP0		20
-#define IRQ_LPC32XX_SSP1		21
-#define IRQ_LPC32XX_I2S0		22
-#define IRQ_LPC32XX_I2S1		23
-#define IRQ_LPC32XX_UART_IIR7		24
-#define IRQ_LPC32XX_UART_IIR2		25
-#define IRQ_LPC32XX_UART_IIR1		26
-#define IRQ_LPC32XX_MSTIMER		27
-#define IRQ_LPC32XX_DMA			28
-#define IRQ_LPC32XX_ETHERNET		29
-#define IRQ_LPC32XX_SUB1FIQ		30
-#define IRQ_LPC32XX_SUB2FIQ		31
-
-/*
- * SIC1 interrupts start at offset 32
- */
-#define IRQ_LPC32XX_JTAG_COMM_TX	LPC32XX_SIC1_IRQ(1)
-#define IRQ_LPC32XX_JTAG_COMM_RX	LPC32XX_SIC1_IRQ(2)
-#define IRQ_LPC32XX_GPI_28		LPC32XX_SIC1_IRQ(4)
-#define IRQ_LPC32XX_TS_P		LPC32XX_SIC1_IRQ(6)
-#define IRQ_LPC32XX_TS_IRQ		LPC32XX_SIC1_IRQ(7)
-#define IRQ_LPC32XX_TS_AUX		LPC32XX_SIC1_IRQ(8)
-#define IRQ_LPC32XX_SPI2		LPC32XX_SIC1_IRQ(12)
-#define IRQ_LPC32XX_PLLUSB		LPC32XX_SIC1_IRQ(13)
-#define IRQ_LPC32XX_PLLHCLK		LPC32XX_SIC1_IRQ(14)
-#define IRQ_LPC32XX_PLL397		LPC32XX_SIC1_IRQ(17)
-#define IRQ_LPC32XX_I2C_2		LPC32XX_SIC1_IRQ(18)
-#define IRQ_LPC32XX_I2C_1		LPC32XX_SIC1_IRQ(19)
-#define IRQ_LPC32XX_RTC			LPC32XX_SIC1_IRQ(20)
-#define IRQ_LPC32XX_KEY			LPC32XX_SIC1_IRQ(22)
-#define IRQ_LPC32XX_SPI1		LPC32XX_SIC1_IRQ(23)
-#define IRQ_LPC32XX_SW			LPC32XX_SIC1_IRQ(24)
-#define IRQ_LPC32XX_USB_OTG_TIMER	LPC32XX_SIC1_IRQ(25)
-#define IRQ_LPC32XX_USB_OTG_ATX		LPC32XX_SIC1_IRQ(26)
-#define IRQ_LPC32XX_USB_HOST		LPC32XX_SIC1_IRQ(27)
-#define IRQ_LPC32XX_USB_DEV_DMA		LPC32XX_SIC1_IRQ(28)
-#define IRQ_LPC32XX_USB_DEV_LP		LPC32XX_SIC1_IRQ(29)
-#define IRQ_LPC32XX_USB_DEV_HP		LPC32XX_SIC1_IRQ(30)
-#define IRQ_LPC32XX_USB_I2C		LPC32XX_SIC1_IRQ(31)
-
-/*
- * SIC2 interrupts start at offset 64
- */
-#define IRQ_LPC32XX_GPIO_00		LPC32XX_SIC2_IRQ(0)
-#define IRQ_LPC32XX_GPIO_01		LPC32XX_SIC2_IRQ(1)
-#define IRQ_LPC32XX_GPIO_02		LPC32XX_SIC2_IRQ(2)
-#define IRQ_LPC32XX_GPIO_03		LPC32XX_SIC2_IRQ(3)
-#define IRQ_LPC32XX_GPIO_04		LPC32XX_SIC2_IRQ(4)
-#define IRQ_LPC32XX_GPIO_05		LPC32XX_SIC2_IRQ(5)
-#define IRQ_LPC32XX_SPI2_DATAIN		LPC32XX_SIC2_IRQ(6)
-#define IRQ_LPC32XX_U2_HCTS		LPC32XX_SIC2_IRQ(7)
-#define IRQ_LPC32XX_P0_P1_IRQ		LPC32XX_SIC2_IRQ(8)
-#define IRQ_LPC32XX_GPI_08		LPC32XX_SIC2_IRQ(9)
-#define IRQ_LPC32XX_GPI_09		LPC32XX_SIC2_IRQ(10)
-#define IRQ_LPC32XX_GPI_19		LPC32XX_SIC2_IRQ(11)
-#define IRQ_LPC32XX_U7_HCTS		LPC32XX_SIC2_IRQ(12)
-#define IRQ_LPC32XX_GPI_07		LPC32XX_SIC2_IRQ(15)
-#define IRQ_LPC32XX_SDIO		LPC32XX_SIC2_IRQ(18)
-#define IRQ_LPC32XX_U5_RX		LPC32XX_SIC2_IRQ(19)
-#define IRQ_LPC32XX_SPI1_DATAIN		LPC32XX_SIC2_IRQ(20)
-#define IRQ_LPC32XX_GPI_00		LPC32XX_SIC2_IRQ(22)
-#define IRQ_LPC32XX_GPI_01		LPC32XX_SIC2_IRQ(23)
-#define IRQ_LPC32XX_GPI_02		LPC32XX_SIC2_IRQ(24)
-#define IRQ_LPC32XX_GPI_03		LPC32XX_SIC2_IRQ(25)
-#define IRQ_LPC32XX_GPI_04		LPC32XX_SIC2_IRQ(26)
-#define IRQ_LPC32XX_GPI_05		LPC32XX_SIC2_IRQ(27)
-#define IRQ_LPC32XX_GPI_06		LPC32XX_SIC2_IRQ(28)
-#define IRQ_LPC32XX_SYSCLK		LPC32XX_SIC2_IRQ(31)
-
-#define LPC32XX_NR_IRQS			96
-
-#endif

arch/arm/mach-lpc32xx/pm.c

@@ -73,7 +73,6 @@
 #include <mach/hardware.h>
 #include <mach/platform.h>
 #include "common.h"
-#include "clock.h"
 
 #define TEMP_IRAM_AREA  IO_ADDRESS(LPC32XX_IRAM_BASE)
 

arch/arm/mach-mediatek/Makefile

-ifeq ($(CONFIG_SMP),y)
-obj-$(CONFIG_ARCH_MEDIATEK) += platsmp.o
-endif
-obj-$(CONFIG_ARCH_MEDIATEK) += mediatek.o
+obj-$(CONFIG_SMP)	+= platsmp.o
+obj-y			+= mediatek.o

arch/arm/mach-omap1/Kconfig

@@ -31,6 +31,32 @@ config ARCH_OMAP16XX
 	select ARCH_OMAP_OTG
 	select CPU_ARM926T
 
+config OMAP_MUX
+	bool "OMAP multiplexing support"
+	depends on ARCH_OMAP
+	default y
+	help
+	  Pin multiplexing support for OMAP boards. If your bootloader
+	  sets the multiplexing correctly, say N. Otherwise, or if unsure,
+	  say Y.
+
+config OMAP_MUX_DEBUG
+	bool "Multiplexing debug output"
+	depends on OMAP_MUX
+	help
+	  Makes the multiplexing functions print out a lot of debug info.
+	  This is useful if you want to find out the correct values of the
+	  multiplexing registers.
+
+config OMAP_MUX_WARNINGS
+	bool "Warn about pins the bootloader didn't set up"
+	depends on OMAP_MUX
+	default y
+	help
+	  Choose Y here to warn whenever driver initialization logic needs
+	  to change the pin multiplexing setup.	 When there are no warnings
+	  printed, it's safe to deselect OMAP_MUX for your product.
+
 comment "OMAP Board Type"
 	depends on ARCH_OMAP1
 

arch/arm/mach-omap1/i2c.c

@@ -19,6 +19,7 @@
  *
  */
 
+#include <linux/i2c.h>
 #include <linux/i2c-omap.h>
 #include <mach/mux.h>
 #include "soc.h"
@@ -91,6 +92,88 @@ int __init omap_i2c_add_bus(struct omap_i2c_bus_platform_data *pdata,
 	return platform_device_register(pdev);
 }
 
+#define OMAP_I2C_MAX_CONTROLLERS 4
+static struct omap_i2c_bus_platform_data i2c_pdata[OMAP_I2C_MAX_CONTROLLERS];
+
+#define OMAP_I2C_CMDLINE_SETUP	(BIT(31))
+
+/**
+ * omap_i2c_bus_setup - Process command line options for the I2C bus speed
+ * @str: String of options
+ *
+ * This function allow to override the default I2C bus speed for given I2C
+ * bus with a command line option.
+ *
+ * Format: i2c_bus=bus_id,clkrate (in kHz)
+ *
+ * Returns 1 on success, 0 otherwise.
+ */
+static int __init omap_i2c_bus_setup(char *str)
+{
+	int ints[3];
+
+	get_options(str, 3, ints);
+	if (ints[0] < 2 || ints[1] < 1 ||
+			ints[1] > OMAP_I2C_MAX_CONTROLLERS)
+		return 0;
+	i2c_pdata[ints[1] - 1].clkrate = ints[2];
+	i2c_pdata[ints[1] - 1].clkrate |= OMAP_I2C_CMDLINE_SETUP;
+
+	return 1;
+}
+__setup("i2c_bus=", omap_i2c_bus_setup);
+
+/*
+ * Register busses defined in command line but that are not registered with
+ * omap_register_i2c_bus from board initialization code.
+ */
+int __init omap_register_i2c_bus_cmdline(void)
+{
+	int i, err = 0;
+
+	for (i = 0; i < ARRAY_SIZE(i2c_pdata); i++)
+		if (i2c_pdata[i].clkrate & OMAP_I2C_CMDLINE_SETUP) {
+			i2c_pdata[i].clkrate &= ~OMAP_I2C_CMDLINE_SETUP;
+			err = omap_i2c_add_bus(&i2c_pdata[i], i + 1);
+			if (err)
+				goto out;
+		}
+
+out:
+	return err;
+}
+
+/**
+ * omap_register_i2c_bus - register I2C bus with device descriptors
+ * @bus_id: bus id counting from number 1
+ * @clkrate: clock rate of the bus in kHz
+ * @info: pointer into I2C device descriptor table or NULL
+ * @len: number of descriptors in the table
+ *
+ * Returns 0 on success or an error code.
+ */
+int __init omap_register_i2c_bus(int bus_id, u32 clkrate,
+			  struct i2c_board_info const *info,
+			  unsigned len)
+{
+	int err;
+
+	BUG_ON(bus_id < 1 || bus_id > OMAP_I2C_MAX_CONTROLLERS);
+
+	if (info) {
+		err = i2c_register_board_info(bus_id, info, len);
+		if (err)
+			return err;
+	}
+
+	if (!i2c_pdata[bus_id - 1].clkrate)
+		i2c_pdata[bus_id - 1].clkrate = clkrate;
+
+	i2c_pdata[bus_id - 1].clkrate &= ~OMAP_I2C_CMDLINE_SETUP;
+
+	return omap_i2c_add_bus(&i2c_pdata[bus_id - 1], bus_id);
+}
+
 static  int __init omap_i2c_cmdline(void)
 {
 	return omap_register_i2c_bus_cmdline();

arch/arm/mach-omap2/Makefile

@@ -6,7 +6,7 @@ ccflags-y := -I$(srctree)/$(src)/include \
 	-I$(srctree)/arch/arm/plat-omap/include
 
 # Common support
-obj-y := id.o io.o control.o mux.o devices.o fb.o serial.o timer.o pm.o \
+obj-y := id.o io.o control.o devices.o fb.o timer.o pm.o \
 	 common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o omap_hwmod.o \
 	 omap_device.o omap-headsmp.o sram.o drm.o
 
@@ -63,9 +63,6 @@ obj-$(CONFIG_ARCH_OMAP4)		+= omap4-restart.o
 obj-$(CONFIG_SOC_OMAP5)			+= omap4-restart.o
 obj-$(CONFIG_SOC_DRA7XX)		+= omap4-restart.o
 
-# Pin multiplexing
-obj-$(CONFIG_ARCH_OMAP3)		+= mux34xx.o
-
 # SMS/SDRC
 obj-$(CONFIG_ARCH_OMAP2)		+= sdrc2xxx.o
 # obj-$(CONFIG_ARCH_OMAP3)		+= sdrc3xxx.o
@@ -80,7 +77,7 @@ endif
 # Power Management
 omap-4-5-pm-common			= omap-mpuss-lowpower.o
 obj-$(CONFIG_ARCH_OMAP4)		+= $(omap-4-5-pm-common)
-obj-$(CONFIG_ARCH_OMAP5)		+= $(omap-4-5-pm-common)
+obj-$(CONFIG_SOC_OMAP5)			+= $(omap-4-5-pm-common)
 obj-$(CONFIG_OMAP_PM_NOOP)		+= omap-pm-noop.o
 
 ifeq ($(CONFIG_PM),y)
@@ -235,26 +232,15 @@ obj-$(CONFIG_MACH_NOKIA_N8X0)		+= board-n8x0.o
 
 # Platform specific device init code
 
-omap-flash-$(CONFIG_MTD_NAND_OMAP2)	:= board-flash.o
-omap-flash-$(CONFIG_MTD_ONENAND_OMAP2)	:= board-flash.o
-obj-y					+= $(omap-flash-y) $(omap-flash-m)
-
 omap-hsmmc-$(CONFIG_MMC_OMAP_HS)	:= hsmmc.o
 obj-y					+= $(omap-hsmmc-m) $(omap-hsmmc-y)
 
-obj-y					+= usb-musb.o
 obj-y					+= omap_phy_internal.o
 
 obj-$(CONFIG_MACH_OMAP2_TUSB6010)	+= usb-tusb6010.o
-obj-y					+= usb-host.o
 
 onenand-$(CONFIG_MTD_ONENAND_OMAP2)	:= gpmc-onenand.o
 obj-y					+= $(onenand-m) $(onenand-y)
 
 nand-$(CONFIG_MTD_NAND_OMAP2)		:= gpmc-nand.o
 obj-y					+= $(nand-m) $(nand-y)
-
-smsc911x-$(CONFIG_SMSC911X)		:= gpmc-smsc911x.o
-obj-y					+= $(smsc911x-m) $(smsc911x-y)
-
-obj-y					+= common-board-devices.o twl-common.o dss-common.o

arch/arm/mach-omap2/board-flash.c

-/*
- * board-flash.c
- * Modified from mach-omap2/board-3430sdp-flash.c
- *
- * Copyright (C) 2009 Nokia Corporation
- * Copyright (C) 2009 Texas Instruments
- *
- * Vimal Singh <vimalsingh@ti.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/omap-gpmc.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/physmap.h>
-#include <linux/io.h>
-
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <linux/platform_data/mtd-onenand-omap2.h>
-
-#include "soc.h"
-#include "common.h"
-#include "board-flash.h"
-
-#define REG_FPGA_REV			0x10
-#define REG_FPGA_DIP_SWITCH_INPUT2	0x60
-#define MAX_SUPPORTED_GPMC_CONFIG	3
-
-#define DEBUG_BASE		0x08000000 /* debug board */
-
-/* various memory sizes */
-#define FLASH_SIZE_SDPV1	SZ_64M	/* NOR flash (64 Meg aligned) */
-#define FLASH_SIZE_SDPV2	SZ_128M	/* NOR flash (256 Meg aligned) */
-
-static struct physmap_flash_data board_nor_data = {
-	.width		= 2,
-};
-
-static struct resource board_nor_resource = {
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device board_nor_device = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-			.platform_data = &board_nor_data,
-	},
-	.num_resources	= 1,
-	.resource	= &board_nor_resource,
-};
-
-static void
-__init board_nor_init(struct mtd_partition *nor_parts, u8 nr_parts, u8 cs)
-{
-	int err;
-
-	board_nor_data.parts	= nor_parts;
-	board_nor_data.nr_parts	= nr_parts;
-
-	/* Configure start address and size of NOR device */
-	if (omap_rev() >= OMAP3430_REV_ES1_0) {
-		err = gpmc_cs_request(cs, FLASH_SIZE_SDPV2 - 1,
-				(unsigned long *)&board_nor_resource.start);
-		board_nor_resource.end = board_nor_resource.start
-					+ FLASH_SIZE_SDPV2 - 1;
-	} else {
-		err = gpmc_cs_request(cs, FLASH_SIZE_SDPV1 - 1,
-				(unsigned long *)&board_nor_resource.start);
-		board_nor_resource.end = board_nor_resource.start
-					+ FLASH_SIZE_SDPV1 - 1;
-	}
-	if (err < 0) {
-		pr_err("NOR: Can't request GPMC CS\n");
-		return;
-	}
-	if (platform_device_register(&board_nor_device) < 0)
-		pr_err("Unable to register NOR device\n");
-}
-
-#if IS_ENABLED(CONFIG_MTD_ONENAND_OMAP2)
-static struct omap_onenand_platform_data board_onenand_data = {
-	.dma_channel	= -1,   /* disable DMA in OMAP OneNAND driver */
-};
-
-void
-__init board_onenand_init(struct mtd_partition *onenand_parts,
-				u8 nr_parts, u8 cs)
-{
-	board_onenand_data.cs		= cs;
-	board_onenand_data.parts	= onenand_parts;
-	board_onenand_data.nr_parts	= nr_parts;
-
-	gpmc_onenand_init(&board_onenand_data);
-}
-#endif /* IS_ENABLED(CONFIG_MTD_ONENAND_OMAP2) */
-
-#if IS_ENABLED(CONFIG_MTD_NAND_OMAP2)
-
-/* Note that all values in this struct are in nanoseconds */
-struct gpmc_timings nand_default_timings[1] = {
-	{
-		.sync_clk = 0,
-
-		.cs_on = 0,
-		.cs_rd_off = 36,
-		.cs_wr_off = 36,
-
-		.we_on = 6,
-		.oe_on = 6,
-
-		.adv_on = 6,
-		.adv_rd_off = 24,
-		.adv_wr_off = 36,
-
-		.we_off = 30,
-		.oe_off = 48,
-
-		.access = 54,
-		.rd_cycle = 72,
-		.wr_cycle = 72,
-
-		.wr_access = 30,
-		.wr_data_mux_bus = 0,
-	},
-};
-
-static struct omap_nand_platform_data board_nand_data;
-
-void
-__init board_nand_init(struct mtd_partition *nand_parts, u8 nr_parts, u8 cs,
-				int nand_type, struct gpmc_timings *gpmc_t)
-{
-	board_nand_data.cs		= cs;
-	board_nand_data.parts		= nand_parts;
-	board_nand_data.nr_parts	= nr_parts;
-	board_nand_data.devsize		= nand_type;
-
-	board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_SW;
-	gpmc_nand_init(&board_nand_data, gpmc_t);
-}
-#endif /* IS_ENABLED(CONFIG_MTD_NAND_OMAP2) */
-
-/**
- * get_gpmc0_type - Reads the FPGA DIP_SWITCH_INPUT_REGISTER2 to get
- * the various cs values.
- */
-static u8 get_gpmc0_type(void)
-{
-	u8 cs = 0;
-	void __iomem *fpga_map_addr;
-
-	fpga_map_addr = ioremap(DEBUG_BASE, 4096);
-	if (!fpga_map_addr)
-		return -ENOMEM;
-
-	if (!(readw_relaxed(fpga_map_addr + REG_FPGA_REV)))
-		/* we dont have an DEBUG FPGA??? */
-		/* Depend on #defines!! default to strata boot return param */
-		goto unmap;
-
-	/* S8-DIP-OFF = 1, S8-DIP-ON = 0 */
-	cs = readw_relaxed(fpga_map_addr + REG_FPGA_DIP_SWITCH_INPUT2) & 0xf;
-
-	/* ES2.0 SDP's onwards 4 dip switches are provided for CS */
-	if (omap_rev() >= OMAP3430_REV_ES1_0)
-		/* change (S8-1:4=DS-2:0) to (S8-4:1=DS-2:0) */
-		cs = ((cs & 8) >> 3) | ((cs & 4) >> 1) |
-			((cs & 2) << 1) | ((cs & 1) << 3);
-	else
-		/* change (S8-1:3=DS-2:0) to (S8-3:1=DS-2:0) */
-		cs = ((cs & 4) >> 2) | (cs & 2) | ((cs & 1) << 2);
-unmap:
-	iounmap(fpga_map_addr);
-	return cs;
-}
-
-/**
- * board_flash_init - Identify devices connected to GPMC and register.
- *
- * @return - void.
- */
-void __init board_flash_init(struct flash_partitions partition_info[],
-			char chip_sel_board[][GPMC_CS_NUM], int nand_type)
-{
-	u8		cs = 0;
-	u8		norcs = GPMC_CS_NUM + 1;
-	u8		nandcs = GPMC_CS_NUM + 1;
-	u8		onenandcs = GPMC_CS_NUM + 1;
-	u8		idx;
-	unsigned char	*config_sel = NULL;
-
-	/* REVISIT: Is this return correct idx for 2430 SDP?
-	 * for which cs configuration matches for 2430 SDP?
-	 */
-	idx = get_gpmc0_type();
-	if (idx >= MAX_SUPPORTED_GPMC_CONFIG) {
-		pr_err("%s: Invalid chip select: %d\n", __func__, cs);
-		return;
-	}
-	config_sel = (unsigned char *)(chip_sel_board[idx]);
-
-	while (cs < GPMC_CS_NUM) {
-		switch (config_sel[cs]) {
-		case PDC_NOR:
-			if (norcs > GPMC_CS_NUM)
-				norcs = cs;
-			break;
-		case PDC_NAND:
-			if (nandcs > GPMC_CS_NUM)
-				nandcs = cs;
-			break;
-		case PDC_ONENAND:
-			if (onenandcs > GPMC_CS_NUM)
-				onenandcs = cs;
-			break;
-		}
-		cs++;
-	}
-
-	if (norcs > GPMC_CS_NUM)
-		pr_err("NOR: Unable to find configuration in GPMC\n");
-	else
-		board_nor_init(partition_info[0].parts,
-				partition_info[0].nr_parts, norcs);
-
-	if (onenandcs > GPMC_CS_NUM)
-		pr_err("OneNAND: Unable to find configuration in GPMC\n");
-	else
-		board_onenand_init(partition_info[1].parts,
-					partition_info[1].nr_parts, onenandcs);
-
-	if (nandcs > GPMC_CS_NUM)
-		pr_err("NAND: Unable to find configuration in GPMC\n");
-	else
-		board_nand_init(partition_info[2].parts,
-			partition_info[2].nr_parts, nandcs,
-			nand_type, nand_default_timings);
-}

arch/arm/mach-omap2/board-flash.h

-/*
- *  board-sdp.h
- *
- *  Information structures for SDP-specific board config data
- *
- *  Copyright (C) 2009 Nokia Corporation
- *  Copyright (C) 2009 Texas Instruments
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-
-#define PDC_NOR		1
-#define PDC_NAND	2
-#define PDC_ONENAND	3
-#define DBG_MPDB	4
-
-struct flash_partitions {
-	struct mtd_partition *parts;
-	int nr_parts;
-};
-
-#if IS_ENABLED(CONFIG_MTD_NAND_OMAP2) || IS_ENABLED(CONFIG_MTD_ONENAND_OMAP2)
-extern void board_flash_init(struct flash_partitions [],
-				char chip_sel[][GPMC_CS_NUM], int nand_type);
-#else
-static inline void board_flash_init(struct flash_partitions part[],
-				char chip_sel[][GPMC_CS_NUM], int nand_type)
-{
-}
-#endif
-
-#if IS_ENABLED(CONFIG_MTD_NAND_OMAP2)
-extern void board_nand_init(struct mtd_partition *nand_parts,
-		u8 nr_parts, u8 cs, int nand_type, struct gpmc_timings *gpmc_t);
-extern struct gpmc_timings nand_default_timings[];
-#else
-static inline void board_nand_init(struct mtd_partition *nand_parts,
-		u8 nr_parts, u8 cs, int nand_type, struct gpmc_timings *gpmc_t)
-{
-}
-#define	nand_default_timings	NULL
-#endif
-
-#if IS_ENABLED(CONFIG_MTD_ONENAND_OMAP2)
-extern void board_onenand_init(struct mtd_partition *nand_parts,
-					u8 nr_parts, u8 cs);
-#else
-static inline void board_onenand_init(struct mtd_partition *nand_parts,
-					u8 nr_parts, u8 cs)
-{
-}
-#endif

arch/arm/mach-omap2/board-generic.c

@@ -339,6 +339,7 @@ static const char *const dra72x_boards_compat[] __initconst = {
 	"ti,am5718",
 	"ti,am5716",
 	"ti,dra722",
+	"ti,dra718",
 	NULL,
 };
 

arch/arm/mach-omap2/clockdomains7xx_data.c

@@ -409,7 +409,7 @@ static struct clockdomain l4sec_7xx_clkdm = {
 	.dep_bit	  = DRA7XX_L4SEC_STATDEP_SHIFT,
 	.wkdep_srcs	  = l4sec_wkup_sleep_deps,
 	.sleepdep_srcs	  = l4sec_wkup_sleep_deps,
-	.flags		  = CLKDM_CAN_HWSUP_SWSUP,
+	.flags		  = CLKDM_CAN_SWSUP,
 };
 
 static struct clockdomain l3main1_7xx_clkdm = {

arch/arm/mach-omap2/common-board-devices.c

-/*
- * common-board-devices.c
- *
- * Copyright (C) 2011 CompuLab, Ltd.
- * Author: Mike Rapoport <mike@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#include <linux/gpio.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "common.h"
-#include "common-board-devices.h"
-
-#if IS_ENABLED(CONFIG_TOUCHSCREEN_ADS7846)
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
-	.turbo_mode	= 0,
-};
-
-static struct ads7846_platform_data ads7846_config = {
-	.x_max			= 0x0fff,
-	.y_max			= 0x0fff,
-	.x_plate_ohms		= 180,
-	.pressure_max		= 255,
-	.debounce_max		= 10,
-	.debounce_tol		= 3,
-	.debounce_rep		= 1,
-	.gpio_pendown		= -EINVAL,
-	.keep_vref_on		= 1,
-};
-
-static struct spi_board_info ads7846_spi_board_info __initdata = {
-	.modalias		= "ads7846",
-	.bus_num		= -EINVAL,
-	.chip_select		= 0,
-	.max_speed_hz		= 1500000,
-	.controller_data	= &ads7846_mcspi_config,
-	.irq			= -EINVAL,
-	.platform_data		= &ads7846_config,
-};
-
-void __init omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
-			      struct ads7846_platform_data *board_pdata)
-{
-	struct spi_board_info *spi_bi = &ads7846_spi_board_info;
-	int err;
-
-	/*
-	 * If a board defines get_pendown_state() function, request the pendown
-	 * GPIO and set the GPIO debounce time.
-	 * If a board does not define the get_pendown_state() function, then
-	 * the ads7846 driver will setup the pendown GPIO itself.
-	 */
-	if (board_pdata && board_pdata->get_pendown_state) {
-		err = gpio_request_one(gpio_pendown, GPIOF_IN, "TSPenDown");
-		if (err) {
-			pr_err("Couldn't obtain gpio for TSPenDown: %d\n", err);
-			return;
-		}
-
-		if (gpio_debounce)
-			gpio_set_debounce(gpio_pendown, gpio_debounce);
-
-		gpio_export(gpio_pendown, 0);
-	}
-
-	spi_bi->bus_num	= bus_num;
-	spi_bi->irq	= gpio_to_irq(gpio_pendown);
-
-	ads7846_config.gpio_pendown = gpio_pendown;
-
-	if (board_pdata) {
-		board_pdata->gpio_pendown = gpio_pendown;
-		board_pdata->gpio_pendown_debounce = gpio_debounce;
-		spi_bi->platform_data = board_pdata;
-	}
-
-	spi_register_board_info(&ads7846_spi_board_info, 1);
-}
-#else
-void __init omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
-			      struct ads7846_platform_data *board_pdata)
-{
-}
-#endif

arch/arm/mach-omap2/common-board-devices.h

@@ -3,15 +3,7 @@
 
 #include <sound/tlv320aic3x.h>
 #include <linux/mfd/menelaus.h>
-#include "twl-common.h"
 
-#define NAND_BLOCK_SIZE	SZ_128K
-
-struct mtd_partition;
-struct ads7846_platform_data;
-
-void omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
-		       struct ads7846_platform_data *board_pdata);
 void *n8x0_legacy_init(void);
 
 extern struct menelaus_platform_data n8x0_menelaus_platform_data;

arch/arm/mach-omap2/common.h

@@ -77,15 +77,6 @@ static inline int omap4_pm_init_early(void)
 }
 #endif
 
-#ifdef CONFIG_OMAP_MUX
-int omap_mux_late_init(void);
-#else
-static inline int omap_mux_late_init(void)
-{
-	return 0;
-}
-#endif
-
 extern void omap2_init_common_infrastructure(void);
 
 extern void omap_init_time(void);
@@ -262,8 +253,6 @@ extern void __iomem *omap4_get_sar_ram_base(void);
 extern void omap4_mpuss_early_init(void);
 extern void omap_do_wfi(void);
 
-extern void omap4_secondary_startup(void);
-extern void omap4460_secondary_startup(void);
 
 #ifdef CONFIG_SMP
 /* Needed for secondary core boot */
@@ -275,16 +264,11 @@ extern void omap4_cpu_die(unsigned int cpu);
 extern int omap4_cpu_kill(unsigned int cpu);
 
 extern const struct smp_operations omap4_smp_ops;
-
-extern void omap5_secondary_startup(void);
-extern void omap5_secondary_hyp_startup(void);
 #endif
 
 #if defined(CONFIG_SMP) && defined(CONFIG_PM)
 extern int omap4_mpuss_init(void);
 extern int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state);
-extern int omap4_finish_suspend(unsigned long cpu_state);
-extern void omap4_cpu_resume(void);
 extern int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state);
 #else
 static inline int omap4_enter_lowpower(unsigned int cpu,
@@ -305,14 +289,41 @@ static inline int omap4_mpuss_init(void)
 	return 0;
 }
 
+#endif
+
+#ifdef CONFIG_ARCH_OMAP4
+void omap4_secondary_startup(void);
+void omap4460_secondary_startup(void);
+int omap4_finish_suspend(unsigned long cpu_state);
+void omap4_cpu_resume(void);
+#else
+static inline void omap4_secondary_startup(void)
+{
+}
+
+static inline void omap4460_secondary_startup(void)
+{
+}
 static inline int omap4_finish_suspend(unsigned long cpu_state)
 {
 	return 0;
 }
-
 static inline void omap4_cpu_resume(void)
-{}
+{
+}
+#endif
 
+#if defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX)
+void omap5_secondary_startup(void);
+void omap5_secondary_hyp_startup(void);
+#else
+static inline void omap5_secondary_startup(void)
+{
+}
+
+static inline void omap5_secondary_hyp_startup(void)
+{
+}
 #endif
 
 void pdata_quirks_init(const struct of_device_id *);

arch/arm/mach-omap2/cpuidle44xx.c

@@ -21,6 +21,7 @@
 #include "common.h"
 #include "pm.h"
 #include "prm.h"
+#include "soc.h"
 #include "clockdomain.h"
 
 #define MAX_CPUS	2
@@ -30,6 +31,7 @@ struct idle_statedata {
 	u32 cpu_state;
 	u32 mpu_logic_state;
 	u32 mpu_state;
+	u32 mpu_state_vote;
 };
 
 static struct idle_statedata omap4_idle_data[] = {
@@ -50,12 +52,26 @@ static struct idle_statedata omap4_idle_data[] = {
 	},
 };
 
+static struct idle_statedata omap5_idle_data[] = {
+	{
+		.cpu_state = PWRDM_POWER_ON,
+		.mpu_state = PWRDM_POWER_ON,
+		.mpu_logic_state = PWRDM_POWER_ON,
+	},
+	{
+		.cpu_state = PWRDM_POWER_RET,
+		.mpu_state = PWRDM_POWER_RET,
+		.mpu_logic_state = PWRDM_POWER_RET,
+	},
+};
+
 static struct powerdomain *mpu_pd, *cpu_pd[MAX_CPUS];
 static struct clockdomain *cpu_clkdm[MAX_CPUS];
 
 static atomic_t abort_barrier;
 static bool cpu_done[MAX_CPUS];
 static struct idle_statedata *state_ptr = &omap4_idle_data[0];
+static DEFINE_RAW_SPINLOCK(mpu_lock);
 
 /* Private functions */
 
@@ -77,6 +93,32 @@ static int omap_enter_idle_simple(struct cpuidle_device *dev,
 	return index;
 }
 
+static int omap_enter_idle_smp(struct cpuidle_device *dev,
+			       struct cpuidle_driver *drv,
+			       int index)
+{
+	struct idle_statedata *cx = state_ptr + index;
+	unsigned long flag;
+
+	raw_spin_lock_irqsave(&mpu_lock, flag);
+	cx->mpu_state_vote++;
+	if (cx->mpu_state_vote == num_online_cpus()) {
+		pwrdm_set_logic_retst(mpu_pd, cx->mpu_logic_state);
+		omap_set_pwrdm_state(mpu_pd, cx->mpu_state);
+	}
+	raw_spin_unlock_irqrestore(&mpu_lock, flag);
+
+	omap4_enter_lowpower(dev->cpu, cx->cpu_state);
+
+	raw_spin_lock_irqsave(&mpu_lock, flag);
+	if (cx->mpu_state_vote == num_online_cpus())
+		omap_set_pwrdm_state(mpu_pd, PWRDM_POWER_ON);
+	cx->mpu_state_vote--;
+	raw_spin_unlock_irqrestore(&mpu_lock, flag);
+
+	return index;
+}
+
 static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 			struct cpuidle_driver *drv,
 			int index)
@@ -220,6 +262,32 @@ static struct cpuidle_driver omap4_idle_driver = {
 	.safe_state_index = 0,
 };
 
+static struct cpuidle_driver omap5_idle_driver = {
+	.name				= "omap5_idle",
+	.owner				= THIS_MODULE,
+	.states = {
+		{
+			/* C1 - CPU0 ON + CPU1 ON + MPU ON */
+			.exit_latency = 2 + 2,
+			.target_residency = 5,
+			.enter = omap_enter_idle_simple,
+			.name = "C1",
+			.desc = "CPUx WFI, MPUSS ON"
+		},
+		{
+			/* C2 - CPU0 RET + CPU1 RET + MPU CSWR */
+			.exit_latency = 48 + 60,
+			.target_residency = 100,
+			.flags = CPUIDLE_FLAG_TIMER_STOP,
+			.enter = omap_enter_idle_smp,
+			.name = "C2",
+			.desc = "CPUx CSWR, MPUSS CSWR",
+		},
+	},
+	.state_count = ARRAY_SIZE(omap5_idle_data),
+	.safe_state_index = 0,
+};
+
 /* Public functions */
 
 /**
@@ -230,6 +298,16 @@ static struct cpuidle_driver omap4_idle_driver = {
  */
 int __init omap4_idle_init(void)
 {
+	struct cpuidle_driver *idle_driver;
+
+	if (soc_is_omap54xx()) {
+		state_ptr = &omap5_idle_data[0];
+		idle_driver = &omap5_idle_driver;
+	} else {
+		state_ptr = &omap4_idle_data[0];
+		idle_driver = &omap4_idle_driver;
+	}
+
 	mpu_pd = pwrdm_lookup("mpu_pwrdm");
 	cpu_pd[0] = pwrdm_lookup("cpu0_pwrdm");
 	cpu_pd[1] = pwrdm_lookup("cpu1_pwrdm");
@@ -244,5 +322,5 @@ int __init omap4_idle_init(void)
 	/* Configure the broadcast timer on each cpu */
 	on_each_cpu(omap_setup_broadcast_timer, NULL, 1);
 
-	return cpuidle_register(&omap4_idle_driver, cpu_online_mask);
+	return cpuidle_register(idle_driver, cpu_online_mask);
 }

arch/arm/mach-omap2/devices.c

@@ -30,7 +30,6 @@
 
 #include "soc.h"
 #include "common.h"
-#include "mux.h"
 #include "control.h"
 #include "display.h"
 

arch/arm/mach-omap2/dss-common.c

-/*
- * Copyright (C) 2012 Texas Instruments, Inc..
- * Author: Tomi Valkeinen <tomi.valkeinen@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-/*
- * NOTE: this is a transitional file to help with DT adaptation.
- * This file will be removed when DSS supports DT.
- */
-
-#include <linux/kernel.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-
-#include <linux/platform_data/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "soc.h"
-#include "dss-common.h"
-#include "mux.h"
-#include "display.h"
-

arch/arm/mach-omap2/dss-common.h

-#ifndef __OMAP_DSS_COMMON__
-#define __OMAP_DSS_COMMON__
-
-/*
- * NOTE: this is a transitional file to help with DT adaptation.
- * This file will be removed when DSS supports DT.
- */
-
-void __init omap4_panda_display_init_of(void);
-void __init omap_4430sdp_display_init_of(void);
-void __init omap3_igep2_display_init_of(void);
-
-#endif

arch/arm/mach-omap2/gpmc-smsc911x.c

-/*
- * linux/arch/arm/mach-omap2/gpmc-smsc911x.c
- *
- * Copyright (C) 2009 Li-Pro.Net
- * Stephan Linz <linz@li-pro.net>
- *
- * Modified from linux/arch/arm/mach-omap2/gpmc-smc91x.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#define pr_fmt(fmt) "%s: " fmt, __func__
-
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/smsc911x.h>
-
-#include "gpmc.h"
-#include "gpmc-smsc911x.h"
-
-static struct resource gpmc_smsc911x_resources[] = {
-	[0] = {
-		.flags		= IORESOURCE_MEM,
-	},
-	[1] = {
-		.flags		= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
-	},
-};
-
-static struct smsc911x_platform_config gpmc_smsc911x_config = {
-	.phy_interface	= PHY_INTERFACE_MODE_MII,
-	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
-	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
-};
-
-/*
- * Initialize smsc911x device connected to the GPMC. Note that we
- * assume that pin multiplexing is done in the board-*.c file,
- * or in the bootloader.
- */
-void __init gpmc_smsc911x_init(struct omap_smsc911x_platform_data *gpmc_cfg)
-{
-	struct platform_device *pdev;
-	unsigned long cs_mem_base;
-	int ret;
-
-	if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) {
-		pr_err("Failed to request GPMC mem region\n");
-		return;
-	}
-
-	gpmc_smsc911x_resources[0].start = cs_mem_base + 0x0;
-	gpmc_smsc911x_resources[0].end = cs_mem_base + 0xff;
-
-	if (gpio_request_one(gpmc_cfg->gpio_irq, GPIOF_IN, "smsc911x irq")) {
-		pr_err("Failed to request IRQ GPIO%d\n", gpmc_cfg->gpio_irq);
-		goto free1;
-	}
-
-	gpmc_smsc911x_resources[1].start = gpio_to_irq(gpmc_cfg->gpio_irq);
-
-	if (gpio_is_valid(gpmc_cfg->gpio_reset)) {
-		ret = gpio_request_one(gpmc_cfg->gpio_reset,
-				       GPIOF_OUT_INIT_HIGH, "smsc911x reset");
-		if (ret) {
-			pr_err("Failed to request reset GPIO%d\n",
-			       gpmc_cfg->gpio_reset);
-			goto free2;
-		}
-
-		gpio_set_value(gpmc_cfg->gpio_reset, 0);
-		msleep(100);
-		gpio_set_value(gpmc_cfg->gpio_reset, 1);
-	}
-
-	gpmc_smsc911x_config.flags = gpmc_cfg->flags ? : SMSC911X_USE_16BIT;
-
-	pdev = platform_device_register_resndata(NULL, "smsc911x", gpmc_cfg->id,
-		 gpmc_smsc911x_resources, ARRAY_SIZE(gpmc_smsc911x_resources),
-		 &gpmc_smsc911x_config, sizeof(gpmc_smsc911x_config));
-	if (IS_ERR(pdev)) {
-		pr_err("Unable to register platform device\n");
-		gpio_free(gpmc_cfg->gpio_reset);
-		goto free2;
-	}
-
-	return;
-
-free2:
-	gpio_free(gpmc_cfg->gpio_irq);
-free1:
-	gpmc_cs_free(gpmc_cfg->cs);
-
-	pr_err("Could not initialize smsc911x device\n");
-}

arch/arm/mach-omap2/gpmc-smsc911x.h

-/*
- * arch/arm/plat-omap/include/plat/gpmc-smsc911x.h
- *
- * Copyright (C) 2009 Li-Pro.Net
- * Stephan Linz <linz@li-pro.net>
- *
- * Modified from arch/arm/plat-omap/include/plat/gpmc-smc91x.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_OMAP_GPMC_SMSC911X_H__
-
-struct omap_smsc911x_platform_data {
-	int	id;
-	int	cs;
-	int	gpio_irq;
-	int	gpio_reset;
-	u32	flags;
-};
-
-#if IS_ENABLED(CONFIG_SMSC911X)
-
-extern void gpmc_smsc911x_init(struct omap_smsc911x_platform_data *d);
-
-#else
-
-static inline void gpmc_smsc911x_init(struct omap_smsc911x_platform_data *d)
-{
-}
-
-#endif
-#endif

arch/arm/mach-omap2/hsmmc.c

@@ -22,7 +22,6 @@
 #include "omap_device.h"
 #include "omap-pm.h"
 
-#include "mux.h"
 #include "hsmmc.h"
 #include "control.h"
 
@@ -147,91 +146,6 @@ static int nop_mmc_set_power(struct device *dev, int power_on, int vdd)
 	return 0;
 }
 
-static inline void omap_hsmmc_mux(struct omap_hsmmc_platform_data
-				  *mmc_controller, int controller_nr)
-{
-	if (gpio_is_valid(mmc_controller->gpio_cd) &&
-	    (mmc_controller->gpio_cd < OMAP_MAX_GPIO_LINES))
-		omap_mux_init_gpio(mmc_controller->gpio_cd,
-				   OMAP_PIN_INPUT_PULLUP);
-	if (gpio_is_valid(mmc_controller->gpio_cod) &&
-	    (mmc_controller->gpio_cod < OMAP_MAX_GPIO_LINES))
-		omap_mux_init_gpio(mmc_controller->gpio_cod,
-				   OMAP_PIN_INPUT_PULLUP);
-	if (gpio_is_valid(mmc_controller->gpio_wp) &&
-	    (mmc_controller->gpio_wp < OMAP_MAX_GPIO_LINES))
-		omap_mux_init_gpio(mmc_controller->gpio_wp,
-				   OMAP_PIN_INPUT_PULLUP);
-	if (cpu_is_omap34xx()) {
-		if (controller_nr == 0) {
-			omap_mux_init_signal("sdmmc1_clk",
-				OMAP_PIN_INPUT_PULLUP);
-			omap_mux_init_signal("sdmmc1_cmd",
-				OMAP_PIN_INPUT_PULLUP);
-			omap_mux_init_signal("sdmmc1_dat0",
-				OMAP_PIN_INPUT_PULLUP);
-			if (mmc_controller->caps &
-				(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
-				omap_mux_init_signal("sdmmc1_dat1",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc1_dat2",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc1_dat3",
-					OMAP_PIN_INPUT_PULLUP);
-			}
-			if (mmc_controller->caps &
-						MMC_CAP_8_BIT_DATA) {
-				omap_mux_init_signal("sdmmc1_dat4",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc1_dat5",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc1_dat6",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc1_dat7",
-					OMAP_PIN_INPUT_PULLUP);
-			}
-		}
-		if (controller_nr == 1) {
-			/* MMC2 */
-			omap_mux_init_signal("sdmmc2_clk",
-				OMAP_PIN_INPUT_PULLUP);
-			omap_mux_init_signal("sdmmc2_cmd",
-				OMAP_PIN_INPUT_PULLUP);
-			omap_mux_init_signal("sdmmc2_dat0",
-				OMAP_PIN_INPUT_PULLUP);
-
-			/*
-			 * For 8 wire configurations, Lines DAT4, 5, 6 and 7
-			 * need to be muxed in the board-*.c files
-			 */
-			if (mmc_controller->caps &
-				(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
-				omap_mux_init_signal("sdmmc2_dat1",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc2_dat2",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc2_dat3",
-					OMAP_PIN_INPUT_PULLUP);
-			}
-			if (mmc_controller->caps &
-							MMC_CAP_8_BIT_DATA) {
-				omap_mux_init_signal("sdmmc2_dat4.sdmmc2_dat4",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc2_dat5.sdmmc2_dat5",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc2_dat6.sdmmc2_dat6",
-					OMAP_PIN_INPUT_PULLUP);
-				omap_mux_init_signal("sdmmc2_dat7.sdmmc2_dat7",
-					OMAP_PIN_INPUT_PULLUP);
-			}
-		}
-
-		/*
-		 * For MMC3 the pins need to be muxed in the board-*.c files
-		 */
-	}
-}
-
 static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
 					struct omap_hsmmc_platform_data *mmc)
 {
@@ -410,8 +324,6 @@ static void __init omap_hsmmc_init_one(struct omap2_hsmmc_info *hsmmcinfo,
 	if (res < 0)
 		goto free_mmc;
 
-	omap_hsmmc_mux(mmc_data, (ctrl_nr - 1));
-
 	name = "omap_hsmmc";
 	res = snprintf(oh_name, MAX_OMAP_MMC_HWMOD_NAME_LEN,
 		     "mmc%d", ctrl_nr);

arch/arm/mach-omap2/i2c.c

@@ -26,7 +26,6 @@
 
 #include "prm.h"
 #include "common.h"
-#include "mux.h"
 #include "i2c.h"
 
 /* In register I2C_CON, Bit 15 is the I2C enable bit */
@@ -36,20 +35,6 @@
 
 #define MAX_OMAP_I2C_HWMOD_NAME_LEN	16
 
-static void __init omap2_i2c_mux_pins(int bus_id)
-{
-	char mux_name[sizeof("i2c2_scl.i2c2_scl")];
-
-	/* First I2C bus is not muxable */
-	if (bus_id == 1)
-		return;
-
-	sprintf(mux_name, "i2c%i_scl.i2c%i_scl", bus_id, bus_id);
-	omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
-	sprintf(mux_name, "i2c%i_sda.i2c%i_sda", bus_id, bus_id);
-	omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
-}
-
 /**
  * omap_i2c_reset - reset the omap i2c module.
  * @oh: struct omap_hwmod *
@@ -107,85 +92,3 @@ int omap_i2c_reset(struct omap_hwmod *oh)
 
 	return 0;
 }
-
-static int __init omap_i2c_nr_ports(void)
-{
-	int ports = 0;
-
-	if (cpu_is_omap24xx())
-		ports = 2;
-	else if (cpu_is_omap34xx())
-		ports = 3;
-	else if (cpu_is_omap44xx())
-		ports = 4;
-	return ports;
-}
-
-/*
- * XXX This function is a temporary compatibility wrapper - only
- * needed until the I2C driver can be converted to call
- * omap_pm_set_max_dev_wakeup_lat() and handle a return code.
- */
-static void omap_pm_set_max_mpu_wakeup_lat_compat(struct device *dev, long t)
-{
-	omap_pm_set_max_mpu_wakeup_lat(dev, t);
-}
-
-static const char name[] = "omap_i2c";
-
-int __init omap_i2c_add_bus(struct omap_i2c_bus_platform_data *i2c_pdata,
-				int bus_id)
-{
-	int l;
-	struct omap_hwmod *oh;
-	struct platform_device *pdev;
-	char oh_name[MAX_OMAP_I2C_HWMOD_NAME_LEN];
-	struct omap_i2c_bus_platform_data *pdata;
-	struct omap_i2c_dev_attr *dev_attr;
-
-	if (bus_id > omap_i2c_nr_ports())
-		return -EINVAL;
-
-	omap2_i2c_mux_pins(bus_id);
-
-	l = snprintf(oh_name, MAX_OMAP_I2C_HWMOD_NAME_LEN, "i2c%d", bus_id);
-	WARN(l >= MAX_OMAP_I2C_HWMOD_NAME_LEN,
-		"String buffer overflow in I2C%d device setup\n", bus_id);
-	oh = omap_hwmod_lookup(oh_name);
-	if (!oh) {
-			pr_err("Could not look up %s\n", oh_name);
-			return -EEXIST;
-	}
-
-	pdata = i2c_pdata;
-	/*
-	 * pass the hwmod class's CPU-specific knowledge of I2C IP revision in
-	 * use, and functionality implementation flags, up to the OMAP I2C
-	 * driver via platform data
-	 */
-	pdata->rev = oh->class->rev;
-
-	dev_attr = (struct omap_i2c_dev_attr *)oh->dev_attr;
-	pdata->flags = dev_attr->flags;
-
-	/*
-	 * When waiting for completion of a i2c transfer, we need to
-	 * set a wake up latency constraint for the MPU. This is to
-	 * ensure quick enough wakeup from idle, when transfer
-	 * completes.
-	 * Only omap3 has support for constraints
-	 */
-	if (cpu_is_omap34xx())
-		pdata->set_mpu_wkup_lat = omap_pm_set_max_mpu_wakeup_lat_compat;
-	pdev = omap_device_build(name, bus_id, oh, pdata,
-				 sizeof(struct omap_i2c_bus_platform_data));
-	WARN(IS_ERR(pdev), "Could not build omap_device for %s\n", name);
-
-	return PTR_ERR_OR_ZERO(pdev);
-}
-
-static  int __init omap_i2c_cmdline(void)
-{
-	return omap_register_i2c_bus_cmdline();
-}
-omap_subsys_initcall(omap_i2c_cmdline);

arch/arm/mach-omap2/io.c

@@ -427,7 +427,6 @@ static void __init omap_hwmod_init_postsetup(void)
 
 static void __init __maybe_unused omap_common_late_init(void)
 {
-	omap_mux_late_init();
 	omap2_common_pm_late_init();
 	omap_soc_device_init();
 }
@@ -717,10 +716,11 @@ void __init omap5_init_early(void)
 			      OMAP2_L4_IO_ADDRESS(OMAP54XX_SCM_BASE));
 	omap2_set_globals_prcm_mpu(OMAP2_L4_IO_ADDRESS(OMAP54XX_PRCM_MPU_BASE));
 	omap2_control_base_init();
-	omap4_pm_init_early();
 	omap2_prcm_base_init();
 	omap5xxx_check_revision();
 	omap4_sar_ram_init();
+	omap4_mpuss_early_init();
+	omap4_pm_init_early();
 	omap54xx_voltagedomains_init();
 	omap54xx_powerdomains_init();
 	omap54xx_clockdomains_init();

arch/arm/mach-omap2/msdi.c

@@ -30,7 +30,6 @@
 #include "control.h"
 #include "omap_hwmod.h"
 #include "omap_device.h"
-#include "mux.h"
 #include "mmc.h"
 
 /*

arch/arm/mach-omap2/mux.h

-/*
- * Copyright (C) 2009 Nokia
- * Copyright (C) 2009-2010 Texas Instruments
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include "mux34xx.h"
-
-#define OMAP_MUX_TERMINATOR	0xffff
-
-/* 34xx mux mode options for each pin. See TRM for options */
-#define OMAP_MUX_MODE0      0
-#define OMAP_MUX_MODE1      1
-#define OMAP_MUX_MODE2      2
-#define OMAP_MUX_MODE3      3
-#define OMAP_MUX_MODE4      4
-#define OMAP_MUX_MODE5      5
-#define OMAP_MUX_MODE6      6
-#define OMAP_MUX_MODE7      7
-
-/* 24xx/34xx mux bit defines */
-#define OMAP_PULL_ENA			(1 << 3)
-#define OMAP_PULL_UP			(1 << 4)
-#define OMAP_ALTELECTRICALSEL		(1 << 5)
-
-/* omap3/4/5 specific mux bit defines */
-#define OMAP_INPUT_EN			(1 << 8)
-#define OMAP_OFF_EN			(1 << 9)
-#define OMAP_OFFOUT_EN			(1 << 10)
-#define OMAP_OFFOUT_VAL			(1 << 11)
-#define OMAP_OFF_PULL_EN		(1 << 12)
-#define OMAP_OFF_PULL_UP		(1 << 13)
-#define OMAP_WAKEUP_EN			(1 << 14)
-#define OMAP_WAKEUP_EVENT		(1 << 15)
-
-/* Active pin states */
-#define OMAP_PIN_OUTPUT			0
-#define OMAP_PIN_INPUT			OMAP_INPUT_EN
-#define OMAP_PIN_INPUT_PULLUP		(OMAP_PULL_ENA | OMAP_INPUT_EN \
-						| OMAP_PULL_UP)
-#define OMAP_PIN_INPUT_PULLDOWN		(OMAP_PULL_ENA | OMAP_INPUT_EN)
-
-/* Off mode states */
-#define OMAP_PIN_OFF_NONE		0
-#define OMAP_PIN_OFF_OUTPUT_HIGH	(OMAP_OFF_EN | OMAP_OFFOUT_EN \
-						| OMAP_OFFOUT_VAL)
-#define OMAP_PIN_OFF_OUTPUT_LOW		(OMAP_OFF_EN | OMAP_OFFOUT_EN)
-#define OMAP_PIN_OFF_INPUT_PULLUP	(OMAP_OFF_EN | OMAP_OFF_PULL_EN \
-						| OMAP_OFF_PULL_UP)
-#define OMAP_PIN_OFF_INPUT_PULLDOWN	(OMAP_OFF_EN | OMAP_OFF_PULL_EN)
-#define OMAP_PIN_OFF_WAKEUPENABLE	OMAP_WAKEUP_EN
-
-#define OMAP_MODE_GPIO(partition, x)	(((x) & OMAP_MUX_MODE7) == \
-					  partition->gpio)
-#define OMAP_MODE_UART(x)	(((x) & OMAP_MUX_MODE7) == OMAP_MUX_MODE0)
-
-/* Flags for omapX_mux_init */
-#define OMAP_PACKAGE_MASK		0xffff
-#define OMAP_PACKAGE_CBP		6		/* 515-pin 0.40 0.50 */
-#define OMAP_PACKAGE_CUS		5		/* 423-pin 0.65 */
-#define OMAP_PACKAGE_CBB		4		/* 515-pin 0.40 0.50 */
-#define OMAP_PACKAGE_CBC		3		/* 515-pin 0.50 0.65 */
-
-#define OMAP_MUX_NR_MODES		8		/* Available modes */
-#define OMAP_MUX_NR_SIDES		2		/* Bottom & top */
-
-/*
- * omap_mux_init flags definition:
- *
- * OMAP_GPIO_MUX_MODE, bits 0-2: gpio muxing mode, same like pad control
- *      register which includes values from 0-7.
- * OMAP_MUX_REG_8BIT: Ensure that access to padconf is done in 8 bits.
- * The default value is 16 bits.
- */
-#define OMAP_MUX_GPIO_IN_MODE0		OMAP_MUX_MODE0
-#define OMAP_MUX_GPIO_IN_MODE1		OMAP_MUX_MODE1
-#define OMAP_MUX_GPIO_IN_MODE2		OMAP_MUX_MODE2
-#define OMAP_MUX_GPIO_IN_MODE3		OMAP_MUX_MODE3
-#define OMAP_MUX_GPIO_IN_MODE4		OMAP_MUX_MODE4
-#define OMAP_MUX_GPIO_IN_MODE5		OMAP_MUX_MODE5
-#define OMAP_MUX_GPIO_IN_MODE6		OMAP_MUX_MODE6
-#define OMAP_MUX_GPIO_IN_MODE7		OMAP_MUX_MODE7
-#define OMAP_MUX_REG_8BIT		(1 << 3)
-
-/**
- * struct omap_board_data - board specific device data
- * @id: instance id
- * @flags: additional flags for platform init code
- * @pads: array of device specific pads
- * @pads_cnt: ARRAY_SIZE() of pads
- */
-struct omap_board_data {
-	int			id;
-	u32			flags;
-	struct omap_device_pad	*pads;
-	int			pads_cnt;
-};
-
-/**
- * struct mux_partition - contain partition related information
- * @name: name of the current partition
- * @flags: flags specific to this partition
- * @gpio: gpio mux mode
- * @phys: physical address
- * @size: partition size
- * @base: virtual address after ioremap
- * @muxmodes: list of nodes that belong to a partition
- * @node: list node for the partitions linked list
- */
-struct omap_mux_partition {
-	const char		*name;
-	u32			flags;
-	u32			gpio;
-	u32			phys;
-	u32			size;
-	void __iomem		*base;
-	struct list_head	muxmodes;
-	struct list_head	node;
-};
-
-/**
- * struct omap_mux - data for omap mux register offset and it's value
- * @reg_offset:	mux register offset from the mux base
- * @gpio:	GPIO number
- * @muxnames:	available signal modes for a ball
- * @balls:	available balls on the package
- */
-struct omap_mux {
-	u16	reg_offset;
-	u16	gpio;
-#ifdef CONFIG_OMAP_MUX
-	char	*muxnames[OMAP_MUX_NR_MODES];
-#ifdef CONFIG_DEBUG_FS
-	char	*balls[OMAP_MUX_NR_SIDES];
-#endif
-#endif
-};
-
-/**
- * struct omap_ball - data for balls on omap package
- * @reg_offset:	mux register offset from the mux base
- * @balls:	available balls on the package
- */
-struct omap_ball {
-	u16	reg_offset;
-	char	*balls[OMAP_MUX_NR_SIDES];
-};
-
-/**
- * struct omap_board_mux - data for initializing mux registers
- * @reg_offset:	mux register offset from the mux base
- * @mux_value:	desired mux value to set
- */
-struct omap_board_mux {
-	u16	reg_offset;
-	u16	value;
-};
-
-#define OMAP_DEVICE_PAD_REMUX		BIT(1)	/* Dynamically remux a pad,
-						   needs enable, idle and off
-						   values */
-#define OMAP_DEVICE_PAD_WAKEUP		BIT(0)	/* Pad is wake-up capable */
-
-/**
- * struct omap_device_pad - device specific pad configuration
- * @name:		signal name
- * @flags:		pad specific runtime flags
- * @enable:		runtime value for a pad
- * @idle:		idle value for a pad
- * @off:		off value for a pad, defaults to safe mode
- * @partition:		mux partition
- * @mux:		mux register
- */
-struct omap_device_pad {
-	char				*name;
-	u8				flags;
-	u16				enable;
-	u16				idle;
-	u16				off;
-	struct omap_mux_partition	*partition;
-	struct omap_mux			*mux;
-};
-
-struct omap_hwmod_mux_info;
-
-#define OMAP_MUX_STATIC(signal, mode)					\
-{									\
-	.name	= (signal),						\
-	.enable	= (mode),						\
-}
-
-#if defined(CONFIG_OMAP_MUX)
-
-/**
- * omap_mux_init_gpio - initialize a signal based on the GPIO number
- * @gpio:		GPIO number
- * @val:		Options for the mux register value
- */
-int omap_mux_init_gpio(int gpio, int val);
-
-/**
- * omap_mux_init_signal - initialize a signal based on the signal name
- * @muxname:		Mux name in mode0_name.signal_name format
- * @val:		Options for the mux register value
- */
-int omap_mux_init_signal(const char *muxname, int val);
-
-/**
- * omap_hwmod_mux_init - initialize hwmod specific mux data
- * @bpads:		Board specific device signal names
- * @nr_pads:		Number of signal names for the device
- */
-extern struct omap_hwmod_mux_info *
-omap_hwmod_mux_init(struct omap_device_pad *bpads, int nr_pads);
-
-/**
- * omap_hwmod_mux - omap hwmod specific pin muxing
- * @hmux:		Pads for a hwmod
- * @state:		Desired _HWMOD_STATE
- *
- * Called only from omap_hwmod.c, do not use.
- */
-void omap_hwmod_mux(struct omap_hwmod_mux_info *hmux, u8 state);
-
-int omap_mux_get_by_name(const char *muxname,
-		struct omap_mux_partition **found_partition,
-		struct omap_mux **found_mux);
-#else
-
-static inline int omap_mux_get_by_name(const char *muxname,
-		struct omap_mux_partition **found_partition,
-		struct omap_mux **found_mux)
-{
-	return 0;
-}
-
-static inline int omap_mux_init_gpio(int gpio, int val)
-{
-	return 0;
-}
-static inline int omap_mux_init_signal(char *muxname, int val)
-{
-	return 0;
-}
-
-static inline struct omap_hwmod_mux_info *
-omap_hwmod_mux_init(struct omap_device_pad *bpads, int nr_pads)
-{
-	return NULL;
-}
-
-static inline void omap_hwmod_mux(struct omap_hwmod_mux_info *hmux, u8 state)
-{
-}
-
-static struct omap_board_mux *board_mux __maybe_unused;
-
-#endif
-
-/**
- * omap_mux_get_gpio() - get mux register value based on GPIO number
- * @gpio:		GPIO number
- *
- */
-u16 omap_mux_get_gpio(int gpio);
-
-/**
- * omap_mux_set_gpio() - set mux register value based on GPIO number
- * @val:		New mux register value
- * @gpio:		GPIO number
- *
- */
-void omap_mux_set_gpio(u16 val, int gpio);
-
-/**
- * omap_mux_get() - get a mux partition by name
- * @name:		Name of the mux partition
- *
- */
-struct omap_mux_partition *omap_mux_get(const char *name);
-
-/**
- * omap_mux_read() - read mux register
- * @partition:		Mux partition
- * @mux_offset:		Offset of the mux register
- *
- */
-u16 omap_mux_read(struct omap_mux_partition *p, u16 mux_offset);
-
-/**
- * omap_mux_write() - write mux register
- * @partition:		Mux partition
- * @val:		New mux register value
- * @mux_offset:		Offset of the mux register
- *
- * This should be only needed for dynamic remuxing of non-gpio signals.
- */
-void omap_mux_write(struct omap_mux_partition *p, u16 val, u16 mux_offset);
-
-/**
- * omap_mux_write_array() - write an array of mux registers
- * @partition:		Mux partition
- * @board_mux:		Array of mux registers terminated by MAP_MUX_TERMINATOR
- *
- * This should be only needed for dynamic remuxing of non-gpio signals.
- */
-void omap_mux_write_array(struct omap_mux_partition *p,
-			  struct omap_board_mux *board_mux);
-
-/**
- * omap2420_mux_init() - initialize mux system with board specific set
- * @board_mux:		Board specific mux table
- * @flags:		OMAP package type used for the board
- */
-int omap2420_mux_init(struct omap_board_mux *board_mux, int flags);
-
-/**
- * omap2430_mux_init() - initialize mux system with board specific set
- * @board_mux:		Board specific mux table
- * @flags:		OMAP package type used for the board
- */
-int omap2430_mux_init(struct omap_board_mux *board_mux, int flags);
-
-/**
- * omap3_mux_init() - initialize mux system with board specific set
- * @board_mux:		Board specific mux table
- * @flags:		OMAP package type used for the board
- */
-int omap3_mux_init(struct omap_board_mux *board_mux, int flags);
-
-/**
- * omap4_mux_init() - initialize mux system with board specific set
- * @board_subset:	Board specific mux table
- * @board_wkup_subset:	Board specific mux table for wakeup instance
- * @flags:		OMAP package type used for the board
- */
-int omap4_mux_init(struct omap_board_mux *board_subset,
-	struct omap_board_mux *board_wkup_subset, int flags);
-
-/**
- * omap_mux_init - private mux init function, do not call
- */
-int omap_mux_init(const char *name, u32 flags,
-		  u32 mux_pbase, u32 mux_size,
-		  struct omap_mux *superset,
-		  struct omap_mux *package_subset,
-		  struct omap_board_mux *board_mux,
-		  struct omap_ball *package_balls);
-

arch/arm/mach-omap2/omap-mpuss-lowpower.c

@@ -48,6 +48,7 @@
 #include <asm/smp_scu.h>
 #include <asm/pgalloc.h>
 #include <asm/suspend.h>
+#include <asm/virt.h>
 #include <asm/hardware/cache-l2x0.h>
 
 #include "soc.h"
@@ -244,10 +245,9 @@ int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
 		save_state = 1;
 		break;
 	case PWRDM_POWER_RET:
-		if (IS_PM44XX_ERRATUM(PM_OMAP4_CPU_OSWR_DISABLE)) {
+		if (IS_PM44XX_ERRATUM(PM_OMAP4_CPU_OSWR_DISABLE))
 			save_state = 0;
 		break;
-		}
 	default:
 		/*
 		 * CPUx CSWR is invalid hardware state. Also CPUx OSWR
@@ -371,8 +371,12 @@ int __init omap4_mpuss_init(void)
 	pm_info = &per_cpu(omap4_pm_info, 0x0);
 	if (sar_base) {
 		pm_info->scu_sar_addr = sar_base + SCU_OFFSET0;
+		if (cpu_is_omap44xx())
 			pm_info->wkup_sar_addr = sar_base +
 				CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
+		else
+			pm_info->wkup_sar_addr = sar_base +
+				OMAP5_CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
 		pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET0;
 	}
 	pm_info->pwrdm = pwrdm_lookup("cpu0_pwrdm");
@@ -391,8 +395,12 @@ int __init omap4_mpuss_init(void)
 	pm_info = &per_cpu(omap4_pm_info, 0x1);
 	if (sar_base) {
 		pm_info->scu_sar_addr = sar_base + SCU_OFFSET1;
+		if (cpu_is_omap44xx())
 			pm_info->wkup_sar_addr = sar_base +
 				CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
+		else
+			pm_info->wkup_sar_addr = sar_base +
+				OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
 		pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET1;
 	}
 
@@ -453,15 +461,24 @@ void __init omap4_mpuss_early_init(void)
 {
 	unsigned long startup_pa;
 
-	if (!cpu_is_omap44xx())
+	if (!(cpu_is_omap44xx() || soc_is_omap54xx()))
 		return;
 
 	sar_base = omap4_get_sar_ram_base();
 
 	if (cpu_is_omap443x())
 		startup_pa = virt_to_phys(omap4_secondary_startup);
-	else
+	else if (cpu_is_omap446x())
 		startup_pa = virt_to_phys(omap4460_secondary_startup);
+	else if ((__boot_cpu_mode & MODE_MASK) == HYP_MODE)
+		startup_pa = virt_to_phys(omap5_secondary_hyp_startup);
+	else
+		startup_pa = virt_to_phys(omap5_secondary_startup);
 
-	writel_relaxed(startup_pa, sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
+	if (cpu_is_omap44xx())
+		writel_relaxed(startup_pa, sar_base +
+			       CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
+	else
+		writel_relaxed(startup_pa, sar_base +
+			       OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
 }

arch/arm/mach-omap2/omap4-sar-layout.h

@@ -31,6 +31,8 @@
 /* CPUx Wakeup Non-Secure Physical Address offsets in SAR_BANK3 */
 #define CPU0_WAKEUP_NS_PA_ADDR_OFFSET		0xa04
 #define CPU1_WAKEUP_NS_PA_ADDR_OFFSET		0xa08
+#define OMAP5_CPU0_WAKEUP_NS_PA_ADDR_OFFSET	0xe00
+#define OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET	0xe04
 
 #define SAR_BACKUP_STATUS_OFFSET		(SAR_BANK3_OFFSET + 0x500)
 #define SAR_SECURE_RAM_SIZE_OFFSET		(SAR_BANK3_OFFSET + 0x504)

arch/arm/mach-oxnas/Makefile

+obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
+obj-$(CONFIG_HOTPLUG_CPU) 	+= hotplug.o