iwlwifi: mvm: load regdomain at INIT stage

We used to load the regdomain only in the load stage,
this caused the 'iw phy phy0 reg get' command to fail if we
booted a machine with wifi off.
Therefor we should load it in INIT stage already.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.a6077801d7d5.I7d8d5c895bc467efbf81ea055dde366ea01cced1@changeidSigned-off-by: Luca Coelho <luciano.coelho@intel.com>

drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c

@@ -1381,6 +1381,25 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 		reg_query_regdb_wmm(regd->alpha2, center_freq, rule);
 	}
 
+	/*
+	 * Certain firmware versions might report no valid channels
+	 * if booted in RF-kill, i.e. not all calibrations etc. are
+	 * running. We'll get out of this situation later when the
+	 * rfkill is removed and we update the regdomain again, but
+	 * since cfg80211 doesn't accept an empty regdomain, add a
+	 * dummy (unusable) rule here in this case so we can init.
+	 */
+	if (!valid_rules) {
+		valid_rules = 1;
+		rule = &regd->reg_rules[valid_rules - 1];
+		rule->freq_range.start_freq_khz = MHZ_TO_KHZ(2412);
+		rule->freq_range.end_freq_khz = MHZ_TO_KHZ(2413);
+		rule->freq_range.max_bandwidth_khz = MHZ_TO_KHZ(1);
+		rule->power_rule.max_antenna_gain = DBI_TO_MBI(6);
+		rule->power_rule.max_eirp =
+			DBM_TO_MBM(IWL_DEFAULT_MAX_TX_POWER);
+	}
+
 	regd->n_reg_rules = valid_rules;
 
 	/*

drivers/net/wireless/intel/iwlwifi/mvm/nvm.c

 // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
 /*
- * Copyright (C) 2012-2014, 2018-2019 Intel Corporation
+ * Copyright (C) 2012-2014, 2018-2019, 2021 Intel Corporation
  * Copyright (C) 2013-2015 Intel Mobile Communications GmbH
  * Copyright (C) 2016-2017 Intel Deutschland GmbH
  */
@@ -416,7 +416,7 @@ iwl_mvm_update_mcc(struct iwl_mvm *mvm, const char *alpha2,
 	struct iwl_rx_packet *pkt;
 	struct iwl_host_cmd cmd = {
 		.id = MCC_UPDATE_CMD,
-		.flags = CMD_WANT_SKB,
+		.flags = CMD_WANT_SKB | CMD_SEND_IN_RFKILL,
 		.data = { &mcc_update_cmd },
 	};
 

drivers/net/wireless/intel/iwlwifi/mvm/ops.c

@@ -692,11 +692,16 @@ static int iwl_mvm_start_get_nvm(struct iwl_mvm *mvm)
 
 	if (ret && ret != -ERFKILL)
 		iwl_fw_dbg_error_collect(&mvm->fwrt, FW_DBG_TRIGGER_DRIVER);
+	if (!ret && iwl_mvm_is_lar_supported(mvm)) {
+		mvm->hw->wiphy->regulatory_flags |= REGULATORY_WIPHY_SELF_MANAGED;
+		ret = iwl_mvm_init_mcc(mvm);
+	}
 
 	if (!iwlmvm_mod_params.init_dbg || !ret)
 		iwl_mvm_stop_device(mvm);
 
 	mutex_unlock(&mvm->mutex);
+	rtnl_unlock();
 
 	if (ret < 0)
 		IWL_ERR(mvm, "Failed to run INIT ucode: %d\n", ret);