Merge master.kernel.org:/home/rmk/linux-2.6-mmc

* master.kernel.org:/home/rmk/linux-2.6-mmc:
  [ARM] 3457/1: i.MX: SD/MMC support for i.MX/MX1
  [ARM] 3456/1: AT91RM9200 support for 2.6 (MMC/SD driver)

arch/arm/mach-imx/generic.c

@@ -33,6 +33,7 @@
 #include <asm/arch/imx-regs.h>
 
 #include <asm/mach/map.h>
+#include <asm/arch/mmc.h>
 
 void imx_gpio_mode(int gpio_mode)
 {
@@ -175,13 +176,25 @@ static struct resource imx_mmc_resources[] = {
 	},
 };
 
+static u64 imxmmmc_dmamask = 0xffffffffUL;
+
 static struct platform_device imx_mmc_device = {
 	.name		= "imx-mmc",
 	.id		= 0,
+	.dev		= {
+		.dma_mask = &imxmmmc_dmamask,
+		.coherent_dma_mask = 0xffffffff,
+	},
 	.num_resources	= ARRAY_SIZE(imx_mmc_resources),
 	.resource	= imx_mmc_resources,
 };
 
+void __init imx_set_mmc_info(struct imxmmc_platform_data *info)
+{
+	imx_mmc_device.dev.platform_data = info;
+}
+EXPORT_SYMBOL(imx_set_mmc_info);
+
 static struct resource imx_uart1_resources[] = {
 	[0] = {
 		.start	= 0x00206000,

drivers/mmc/Kconfig

@@ -91,4 +91,22 @@ config MMC_AU1X
 
 	  If unsure, say N.
 
+config MMC_AT91RM9200
+	tristate "AT91RM9200 SD/MMC Card Interface support"
+	depends on ARCH_AT91RM9200 && MMC
+	help
+	  This selects the AT91RM9200 MCI controller.
+
+	  If unsure, say N.
+
+config MMC_IMX
+	tristate "Motorola i.MX Multimedia Card Interface support"
+	depends on ARCH_IMX && MMC
+	help
+	  This selects the Motorola i.MX Multimedia card Interface.
+	  If you have a i.MX platform with a Multimedia Card slot,
+	  say Y or M here.
+
+	  If unsure, say N.
+
 endmenu

drivers/mmc/Makefile

@@ -17,10 +17,12 @@ obj-$(CONFIG_MMC_BLOCK)		+= mmc_block.o
 #
 obj-$(CONFIG_MMC_ARMMMCI)	+= mmci.o
 obj-$(CONFIG_MMC_PXA)		+= pxamci.o
+obj-$(CONFIG_MMC_IMX)		+= imxmmc.o
 obj-$(CONFIG_MMC_SDHCI)		+= sdhci.o
 obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
 obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
 obj-$(CONFIG_MMC_OMAP)		+= omap.o
+obj-$(CONFIG_MMC_AT91RM9200)	+= at91_mci.o
 
 mmc_core-y := mmc.o mmc_queue.o mmc_sysfs.o
 

drivers/mmc/imxmmc.h

+
+# define __REG16(x)	(*((volatile u16 *)IO_ADDRESS(x)))
+
+#define MMC_STR_STP_CLK  __REG16(IMX_MMC_BASE + 0x00)
+#define MMC_STATUS       __REG16(IMX_MMC_BASE + 0x04)
+#define MMC_CLK_RATE     __REG16(IMX_MMC_BASE + 0x08)
+#define MMC_CMD_DAT_CONT __REG16(IMX_MMC_BASE + 0x0C)
+#define MMC_RES_TO       __REG16(IMX_MMC_BASE + 0x10)
+#define MMC_READ_TO      __REG16(IMX_MMC_BASE + 0x14)
+#define MMC_BLK_LEN      __REG16(IMX_MMC_BASE + 0x18)
+#define MMC_NOB          __REG16(IMX_MMC_BASE + 0x1C)
+#define MMC_REV_NO       __REG16(IMX_MMC_BASE + 0x20)
+#define MMC_INT_MASK     __REG16(IMX_MMC_BASE + 0x24)
+#define MMC_CMD          __REG16(IMX_MMC_BASE + 0x28)
+#define MMC_ARGH         __REG16(IMX_MMC_BASE + 0x2C)
+#define MMC_ARGL         __REG16(IMX_MMC_BASE + 0x30)
+#define MMC_RES_FIFO     __REG16(IMX_MMC_BASE + 0x34)
+#define MMC_BUFFER_ACCESS __REG16(IMX_MMC_BASE + 0x38)
+#define MMC_BUFFER_ACCESS_OFS 0x38
+
+
+#define STR_STP_CLK_ENDIAN              (1<<5)
+#define STR_STP_CLK_RESET               (1<<3)
+#define STR_STP_CLK_ENABLE              (1<<2)
+#define STR_STP_CLK_START_CLK           (1<<1)
+#define STR_STP_CLK_STOP_CLK            (1<<0)
+#define STATUS_CARD_PRESENCE            (1<<15)
+#define STATUS_SDIO_INT_ACTIVE          (1<<14)
+#define STATUS_END_CMD_RESP             (1<<13)
+#define STATUS_WRITE_OP_DONE            (1<<12)
+#define STATUS_DATA_TRANS_DONE          (1<<11)
+#define STATUS_WR_CRC_ERROR_CODE_MASK   (3<<10)
+#define STATUS_CARD_BUS_CLK_RUN         (1<<8)
+#define STATUS_APPL_BUFF_FF             (1<<7)
+#define STATUS_APPL_BUFF_FE             (1<<6)
+#define STATUS_RESP_CRC_ERR             (1<<5)
+#define STATUS_CRC_READ_ERR             (1<<3)
+#define STATUS_CRC_WRITE_ERR            (1<<2)
+#define STATUS_TIME_OUT_RESP            (1<<1)
+#define STATUS_TIME_OUT_READ            (1<<0)
+#define STATUS_ERR_MASK                 0x2f
+#define CLK_RATE_PRESCALER(x)           ((x) & 0x7)
+#define CLK_RATE_CLK_RATE(x)            (((x) & 0x7) << 3)
+#define CMD_DAT_CONT_CMD_RESP_LONG_OFF  (1<<12)
+#define CMD_DAT_CONT_STOP_READWAIT      (1<<11)
+#define CMD_DAT_CONT_START_READWAIT     (1<<10)
+#define CMD_DAT_CONT_BUS_WIDTH_1        (0<<8)
+#define CMD_DAT_CONT_BUS_WIDTH_4        (2<<8)
+#define CMD_DAT_CONT_INIT               (1<<7)
+#define CMD_DAT_CONT_BUSY               (1<<6)
+#define CMD_DAT_CONT_STREAM_BLOCK       (1<<5)
+#define CMD_DAT_CONT_WRITE              (1<<4)
+#define CMD_DAT_CONT_DATA_ENABLE        (1<<3)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R1 (1)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R2 (2)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R3 (3)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R4 (4)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R5 (5)
+#define CMD_DAT_CONT_RESPONSE_FORMAT_R6 (6)
+#define INT_MASK_AUTO_CARD_DETECT       (1<<6)
+#define INT_MASK_DAT0_EN                (1<<5)
+#define INT_MASK_SDIO                   (1<<4)
+#define INT_MASK_BUF_READY              (1<<3)
+#define INT_MASK_END_CMD_RES            (1<<2)
+#define INT_MASK_WRITE_OP_DONE          (1<<1)
+#define INT_MASK_DATA_TRAN              (1<<0)
+#define INT_ALL                         (0x7f)

include/asm-arm/arch-at91rm9200/at91rm9200_mci.h

+/*
+ * include/asm-arm/arch-at91rm9200/at91rm9200_mci.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * MultiMedia Card Interface (MCI) registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91RM9200_MCI_H
+#define AT91RM9200_MCI_H
+
+#define AT91_MCI_CR		0x00		/* Control Register */
+#define		AT91_MCI_MCIEN		(1 <<  0)	/* Multi-Media Interface Enable */
+#define		AT91_MCI_MCIDIS		(1 <<  1)	/* Multi-Media Interface Disable */
+#define		AT91_MCI_PWSEN		(1 <<  2)	/* Power Save Mode Enable */
+#define		AT91_MCI_PWSDIS		(1 <<  3)	/* Power Save Mode Disable */
+#define		AT91_MCI_SWRST		(1 <<  7)	/* Software Reset */
+
+#define AT91_MCI_MR		0x04		/* Mode Register */
+#define		AT91_MCI_CLKDIV		(0xff  <<  0)	/* Clock Divider */
+#define		AT91_MCI_PWSDIV		(3     <<  8)	/* Power Saving Divider */
+#define		AT91_MCI_PDCPADV	(1     << 14)	/* PDC Padding Value */
+#define		AT91_MCI_PDCMODE	(1     << 15)	/* PDC-orientated Mode */
+#define		AT91_MCI_BLKLEN 	(0xfff << 18)	/* Data Block Length */
+
+#define AT91_MCI_DTOR		0x08		/* Data Timeout Register */
+#define		AT91_MCI_DTOCYC		(0xf << 0)	/* Data Timeout Cycle Number */
+#define		AT91_MCI_DTOMUL		(7   << 4)	/* Data Timeout Multiplier */
+#define		AT91_MCI_DTOMUL_1		(0 <<  4)
+#define		AT91_MCI_DTOMUL_16		(1 <<  4)
+#define		AT91_MCI_DTOMUL_128		(2 <<  4)
+#define		AT91_MCI_DTOMUL_256		(3 <<  4)
+#define		AT91_MCI_DTOMUL_1K		(4 <<  4)
+#define		AT91_MCI_DTOMUL_4K		(5 <<  4)
+#define		AT91_MCI_DTOMUL_64K		(6 <<  4)
+#define		AT91_MCI_DTOMUL_1M		(7 <<  4)
+
+#define AT91_MCI_SDCR		0x0c		/* SD Card Register */
+#define		AT91_MCI_SDCSEL		(0xf << 0)	/* SD Card Selector */
+#define		AT91_MCI_SDCBUS		(1   << 7)	/* 1-bit or 4-bit bus */
+
+#define AT91_MCI_ARGR		0x10		/* Argument Register */
+
+#define AT91_MCI_CMDR		0x14		/* Command Register */
+#define		AT91_MCI_CMDNB		(0x3f << 0)	/* Command Number */
+#define		AT91_MCI_RSPTYP		(3    << 6)	/* Response Type */
+#define			AT91_MCI_RSPTYP_NONE	(0 <<  6)
+#define			AT91_MCI_RSPTYP_48	(1 <<  6)
+#define			AT91_MCI_RSPTYP_136	(2 <<  6)
+#define		AT91_MCI_SPCMD		(7    << 8)	/* Special Command */
+#define			AT91_MCI_SPCMD_NONE	(0 <<  8)
+#define			AT91_MCI_SPCMD_INIT	(1 <<  8)
+#define			AT91_MCI_SPCMD_SYNC	(2 <<  8)
+#define			AT91_MCI_SPCMD_ICMD	(4 <<  8)
+#define			AT91_MCI_SPCMD_IRESP	(5 <<  8)
+#define		AT91_MCI_OPDCMD		(1 << 11)	/* Open Drain Command */
+#define		AT91_MCI_MAXLAT		(1 << 12)	/* Max Latency for Command to Response */
+#define		AT91_MCI_TRCMD		(3 << 16)	/* Transfer Command */
+#define			AT91_MCI_TRCMD_NONE	(0 << 16)
+#define			AT91_MCI_TRCMD_START	(1 << 16)
+#define			AT91_MCI_TRCMD_STOP	(2 << 16)
+#define		AT91_MCI_TRDIR		(1 << 18)	/* Transfer Direction */
+#define		AT91_MCI_TRTYP		(3 << 19)	/* Transfer Type */
+#define			AT91_MCI_TRTYP_BLOCK	(0 << 19)
+#define			AT91_MCI_TRTYP_MULTIPLE	(1 << 19)
+#define			AT91_MCI_TRTYP_STREAM	(2 << 19)
+
+#define AT91_MCI_RSPR(n)	(0x20 + ((n) * 4))	/* Response Registers 0-3 */
+#define AT91_MCR_RDR		0x30		/* Receive Data Register */
+#define AT91_MCR_TDR		0x34		/* Transmit Data Register */
+
+#define AT91_MCI_SR		0x40		/* Status Register */
+#define		AT91_MCI_CMDRDY		(1 <<  0)	/* Command Ready */
+#define		AT91_MCI_RXRDY		(1 <<  1) 	/* Receiver Ready */
+#define		AT91_MCI_TXRDY		(1 <<  2)	/* Transmit Ready */
+#define		AT91_MCI_BLKE		(1 <<  3)	/* Data Block Ended */
+#define		AT91_MCI_DTIP		(1 <<  4)	/* Data Transfer in Progress */
+#define		AT91_MCI_NOTBUSY	(1 <<  5)	/* Data Not Busy */
+#define		AT91_MCI_ENDRX		(1 <<  6)	/* End of RX Buffer */
+#define		AT91_MCI_ENDTX		(1 <<  7)	/* End fo TX Buffer */
+#define		AT91_MCI_RXBUFF		(1 << 14)	/* RX Buffer Full */
+#define		AT91_MCI_TXBUFE		(1 << 15)	/* TX Buffer Empty */
+#define		AT91_MCI_RINDE		(1 << 16)  	/* Response Index Error */
+#define		AT91_MCI_RDIRE		(1 << 17)	/* Response Direction Error */
+#define		AT91_MCI_RCRCE		(1 << 18)   	/* Response CRC Error */
+#define		AT91_MCI_RENDE		(1 << 19)	/* Response End Bit Error */
+#define		AT91_MCI_RTOE		(1 << 20)	/* Reponse Time-out Error */
+#define		AT91_MCI_DCRCE		(1 << 21)	/* Data CRC Error */
+#define		AT91_MCI_DTOE		(1 << 22)	/* Data Time-out Error */
+#define		AT91_MCI_OVRE		(1 << 30)	/* Overrun */
+#define		AT91_MCI_UNRE		(1 << 31)	/* Underrun */
+
+#define AT91_MCI_IER		0x44		/* Interrupt Enable Register */
+#define AT91_MCI_IDR		0x48		/* Interrupt Disable Register */
+#define AT91_MCI_IMR		0x4c		/* Interrupt Mask Register */
+
+#endif

include/asm-arm/arch-imx/mmc.h

+#ifndef ASMARM_ARCH_MMC_H
+#define ASMARM_ARCH_MMC_H
+
+#include <linux/mmc/protocol.h>
+
+struct imxmmc_platform_data {
+	int (*card_present)(void);
+};
+
+extern void imx_set_mmc_info(struct imxmmc_platform_data *info);
+
+#endif