Commit f0b7d43c authored by Brad Campbell's avatar Brad Campbell Committed by Marcel Holtmann

cc2520: Add support for CC2591 amplifier.

The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.

Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.

This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.

The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: default avatarBrad Campbell <bradjc5@gmail.com>
Acked-by: default avatarVarka Bhadram <varkabhadram@gmail.com>
Signed-off-by: default avatarMarcel Holtmann <marcel@holtmann.org>
parent 0db055c9
......@@ -13,11 +13,15 @@ Required properties:
- cca-gpio: GPIO spec for the CCA pin
- vreg-gpio: GPIO spec for the VREG pin
- reset-gpio: GPIO spec for the RESET pin
Optional properties:
- amplified: include if the CC2520 is connected to a CC2591 amplifier
Example:
cc2520@0 {
compatible = "ti,cc2520";
reg = <0>;
spi-max-frequency = <4000000>;
amplified;
pinctrl-names = "default";
pinctrl-0 = <&cc2520_cape_pins>;
fifo-gpio = <&gpio1 18 0>;
......
......@@ -738,6 +738,8 @@ static int cc2520_get_platform_data(struct spi_device *spi,
pdata->vreg = of_get_named_gpio(np, "vreg-gpio", 0);
pdata->reset = of_get_named_gpio(np, "reset-gpio", 0);
pdata->amplified = of_property_read_bool(np, "amplified");
return 0;
}
......@@ -746,6 +748,11 @@ static int cc2520_hw_init(struct cc2520_private *priv)
u8 status = 0, state = 0xff;
int ret;
int timeout = 100;
struct cc2520_platform_data pdata;
ret = cc2520_get_platform_data(priv->spi, &pdata);
if (ret)
goto err_ret;
ret = cc2520_read_register(priv, CC2520_FSMSTAT1, &state);
if (ret)
......@@ -768,11 +775,47 @@ static int cc2520_hw_init(struct cc2520_private *priv)
dev_vdbg(&priv->spi->dev, "oscillator brought up\n");
/* Registers default value: section 28.1 in Datasheet */
/* If the CC2520 is connected to a CC2591 amplifier, we must both
* configure GPIOs on the CC2520 to correctly configure the CC2591
* and change a couple settings of the CC2520 to work with the
* amplifier. See section 8 page 17 of TI application note AN065.
* http://www.ti.com/lit/an/swra229a/swra229a.pdf
*/
if (pdata.amplified) {
ret = cc2520_write_register(priv, CC2520_TXPOWER, 0xF9);
if (ret)
goto err_ret;
ret = cc2520_write_register(priv, CC2520_AGCCTRL1, 0x16);
if (ret)
goto err_ret;
ret = cc2520_write_register(priv, CC2520_GPIOCTRL0, 0x46);
if (ret)
goto err_ret;
ret = cc2520_write_register(priv, CC2520_GPIOCTRL5, 0x47);
if (ret)
goto err_ret;
ret = cc2520_write_register(priv, CC2520_GPIOPOLARITY, 0x1e);
if (ret)
goto err_ret;
ret = cc2520_write_register(priv, CC2520_TXCTRL, 0xc1);
if (ret)
goto err_ret;
} else {
ret = cc2520_write_register(priv, CC2520_TXPOWER, 0xF7);
if (ret)
goto err_ret;
ret = cc2520_write_register(priv, CC2520_AGCCTRL1, 0x11);
if (ret)
goto err_ret;
}
/* Registers default value: section 28.1 in Datasheet */
ret = cc2520_write_register(priv, CC2520_CCACTRL0, 0x1A);
if (ret)
goto err_ret;
......@@ -797,10 +840,6 @@ static int cc2520_hw_init(struct cc2520_private *priv)
if (ret)
goto err_ret;
ret = cc2520_write_register(priv, CC2520_AGCCTRL1, 0x11);
if (ret)
goto err_ret;
ret = cc2520_write_register(priv, CC2520_ADCTEST0, 0x10);
if (ret)
goto err_ret;
......
......@@ -21,6 +21,7 @@ struct cc2520_platform_data {
int sfd;
int reset;
int vreg;
bool amplified;
};
#endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment