Commit f164b845 authored by Mark Rustad's avatar Mark Rustad Committed by Jeff Kirsher

ixgbe: Prevent KR PHY reset in ixgbe_init_phy_ops_x550em

This patch removes KR PHY reset from ixgbe_init_phy_ops_x550em,
since this function is meant to initialize function pointers for
the detected PHY type. Internal PHY reset was moved to
ixgbe_setup_internal_phy_t_x550em which will now detect which
mode the internal PHY operates in and set it up as required.
Signed-off-by: default avatarMark Rustad <mark.d.rustad@intel.com>
Tested-by: default avatarDarin Miller <darin.j.miller@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 6f24e5d5
......@@ -1727,6 +1727,12 @@ static s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw)
if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
return IXGBE_ERR_CONFIG;
if (hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE) {
speed = IXGBE_LINK_SPEED_10GB_FULL |
IXGBE_LINK_SPEED_1GB_FULL;
return ixgbe_setup_kr_speed_x550em(hw, speed);
}
/* If link is not up, then there is no setup necessary so return */
status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
if (status)
......@@ -1931,7 +1937,6 @@ static s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
{
struct ixgbe_phy_info *phy = &hw->phy;
ixgbe_link_speed speed;
s32 ret_val;
hw->mac.ops.set_lan_id(hw);
......@@ -1944,10 +1949,6 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
* to determine internal PHY mode.
*/
phy->nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL);
if (phy->nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE) {
speed = IXGBE_LINK_SPEED_10GB_FULL |
IXGBE_LINK_SPEED_1GB_FULL;
}
}
/* Identify the PHY or SFP module */
......@@ -1979,14 +1980,8 @@ static s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw)
/* If internal link mode is XFI, then setup iXFI internal link,
* else setup KR now.
*/
if (!(phy->nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
phy->ops.setup_internal_link =
ixgbe_setup_internal_phy_t_x550em;
} else {
speed = IXGBE_LINK_SPEED_10GB_FULL |
IXGBE_LINK_SPEED_1GB_FULL;
ret_val = ixgbe_setup_kr_speed_x550em(hw, speed);
}
/* setup SW LPLU only for first revision */
if (!(IXGBE_FUSES0_REV1 & IXGBE_READ_REG(hw,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment