Commit f42ac38c authored by Steven Rostedt's avatar Steven Rostedt Committed by Linus Torvalds

ftrace: disable tracing for suspend to ram

I've been painstakingly debugging the issue with suspend to ram and
ftraced. The 2.6.28 code does not have this issue, but since the mcount
recording is not going to be in 27, this must be solved for the ftrace
daemon version.

The resume from suspend to ram would reboot because it was triple
faulting. Debugging further, I found that calling the mcount function
itself was not an issue, but it would fault when it incremented
preempt_count. preempt_count is on the tasks info structure that is on the
low memory address of the task's stack.  For some reason, it could not
write to it. Resuming out of suspend to ram does quite a lot of funny
tricks to get to work, so it is not surprising at all that simply doing a
preempt_disable() would cause a fault.

Thanks to Rafael for suggesting to add a "while (1);" to find the place in
resuming that is causing the fault. I would place the loop somewhere in
the code, compile and reboot and see if it would either reboot (hit the
fault) or simply hang (hit the loop).  Doing this over and over again, I
narrowed it down that it was happening in enable_nonboot_cpus.

At this point, I found that it is easier to simply disable tracing around
the suspend code, instead of searching for the particular function that
can not handle doing a preempt_disable.

This patch disables the tracer as it suspends and reenables it on resume.

I tested this patch on my Laptop, and it can resume fine with the patch.
Signed-off-by: default avatarSteven Rostedt <srostedt@redhat.com>
Acked-by: default avatarRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 8560c650
...@@ -21,6 +21,7 @@ ...@@ -21,6 +21,7 @@
#include <linux/freezer.h> #include <linux/freezer.h>
#include <linux/vmstat.h> #include <linux/vmstat.h>
#include <linux/syscalls.h> #include <linux/syscalls.h>
#include <linux/ftrace.h>
#include "power.h" #include "power.h"
...@@ -310,7 +311,7 @@ static int suspend_enter(suspend_state_t state) ...@@ -310,7 +311,7 @@ static int suspend_enter(suspend_state_t state)
*/ */
int suspend_devices_and_enter(suspend_state_t state) int suspend_devices_and_enter(suspend_state_t state)
{ {
int error; int error, ftrace_save;
if (!suspend_ops) if (!suspend_ops)
return -ENOSYS; return -ENOSYS;
...@@ -321,6 +322,7 @@ int suspend_devices_and_enter(suspend_state_t state) ...@@ -321,6 +322,7 @@ int suspend_devices_and_enter(suspend_state_t state)
goto Close; goto Close;
} }
suspend_console(); suspend_console();
ftrace_save = __ftrace_enabled_save();
suspend_test_start(); suspend_test_start();
error = device_suspend(PMSG_SUSPEND); error = device_suspend(PMSG_SUSPEND);
if (error) { if (error) {
...@@ -352,6 +354,7 @@ int suspend_devices_and_enter(suspend_state_t state) ...@@ -352,6 +354,7 @@ int suspend_devices_and_enter(suspend_state_t state)
suspend_test_start(); suspend_test_start();
device_resume(PMSG_RESUME); device_resume(PMSG_RESUME);
suspend_test_finish("resume devices"); suspend_test_finish("resume devices");
__ftrace_enabled_restore(ftrace_save);
resume_console(); resume_console();
Close: Close:
if (suspend_ops->end) if (suspend_ops->end)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment