s390: remove SALIPL loader

There is no known user, therefore remove the code.
Acked-by: Rob Van Der Heij <robvdheij@nl.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

arch/s390/kernel/head.S

@@ -60,19 +60,6 @@ __HEAD
 	.long	0x020006e0,0x20000050
 
 	.org	0x200
-#
-# subroutine to set architecture mode
-#
-.Lsetmode:
-	mvi	__LC_AR_MODE_ID,1	# set esame flag
-	slr	%r0,%r0 		# set cpuid to zero
-	lhi	%r1,2			# mode 2 = esame (dump)
-	sigp	%r1,%r0,0x12		# switch to esame mode
-	bras	%r13,0f
-	.fill	16,4,0x0
-0:	lmh	%r0,%r15,0(%r13)	# clear high-order half of gprs
-	sam31				# switch to 31 bit addressing mode
-	br	%r14
 
 #
 # subroutine to wait for end I/O
@@ -160,7 +147,14 @@ __HEAD
 	.long	0x02200050,0x00000000
 
 iplstart:
-	bas	%r14,.Lsetmode		# Immediately switch to 64 bit mode
+	mvi	__LC_AR_MODE_ID,1	# set esame flag
+	slr	%r0,%r0			# set cpuid to zero
+	lhi	%r1,2			# mode 2 = esame (dump)
+	sigp	%r1,%r0,0x12		# switch to esame mode
+	bras	%r13,0f
+	.fill	16,4,0x0
+0:	lmh	%r0,%r15,0(%r13)	# clear high-order half of gprs
+	sam31				# switch to 31 bit addressing mode
 	lh	%r1,0xb8		# test if subchannel number
 	bct	%r1,.Lnoload		#  is valid
 	l	%r1,0xb8		# load ipl subchannel number
@@ -269,71 +263,6 @@ iplstart:
 	.align	8
 .Lcpuid:.fill	8,1,0
 
-#
-# SALIPL loader support. Based on a patch by Rob van der Heij.
-# This entry point is called directly from the SALIPL loader and
-# doesn't need a builtin ipl record.
-#
-	.org	0x800
-ENTRY(start)
-	stm	%r0,%r15,0x07b0		# store registers
-	bas	%r14,.Lsetmode		# Immediately switch to 64 bit mode
-	basr	%r12,%r0
-.base:
-	l	%r11,.parm
-	l	%r8,.cmd		# pointer to command buffer
-
-	ltr	%r9,%r9			# do we have SALIPL parameters?
-	bp	.sk8x8
-
-	mvc	0(64,%r8),0x00b0	# copy saved registers
-	xc	64(240-64,%r8),0(%r8)	# remainder of buffer
-	tr	0(64,%r8),.lowcase
-	b	.gotr
-.sk8x8:
-	mvc	0(240,%r8),0(%r9)	# copy iplparms into buffer
-.gotr:
-	slr	%r0,%r0
-	st	%r0,INITRD_SIZE+ARCH_OFFSET-PARMAREA(%r11)
-	st	%r0,INITRD_START+ARCH_OFFSET-PARMAREA(%r11)
-	j	startup 		# continue with startup
-.cmd:	.long	COMMAND_LINE		# address of command line buffer
-.parm:	.long	PARMAREA
-.lowcase:
-	.byte 0x00,0x01,0x02,0x03,0x04,0x05,0x06,0x07
-	.byte 0x08,0x09,0x0a,0x0b,0x0c,0x0d,0x0e,0x0f
-	.byte 0x10,0x11,0x12,0x13,0x14,0x15,0x16,0x17
-	.byte 0x18,0x19,0x1a,0x1b,0x1c,0x1d,0x1e,0x1f
-	.byte 0x20,0x21,0x22,0x23,0x24,0x25,0x26,0x27
-	.byte 0x28,0x29,0x2a,0x2b,0x2c,0x2d,0x2e,0x2f
-	.byte 0x30,0x31,0x32,0x33,0x34,0x35,0x36,0x37
-	.byte 0x38,0x39,0x3a,0x3b,0x3c,0x3d,0x3e,0x3f
-	.byte 0x40,0x41,0x42,0x43,0x44,0x45,0x46,0x47
-	.byte 0x48,0x49,0x4a,0x4b,0x4c,0x4d,0x4e,0x4f
-	.byte 0x50,0x51,0x52,0x53,0x54,0x55,0x56,0x57
-	.byte 0x58,0x59,0x5a,0x5b,0x5c,0x5d,0x5e,0x5f
-	.byte 0x60,0x61,0x62,0x63,0x64,0x65,0x66,0x67
-	.byte 0x68,0x69,0x6a,0x6b,0x6c,0x6d,0x6e,0x6f
-	.byte 0x70,0x71,0x72,0x73,0x74,0x75,0x76,0x77
-	.byte 0x78,0x79,0x7a,0x7b,0x7c,0x7d,0x7e,0x7f
-
-	.byte 0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87
-	.byte 0x88,0x89,0x8a,0x8b,0x8c,0x8d,0x8e,0x8f
-	.byte 0x90,0x91,0x92,0x93,0x94,0x95,0x96,0x97
-	.byte 0x98,0x99,0x9a,0x9b,0x9c,0x9d,0x9e,0x9f
-	.byte 0xa0,0xa1,0xa2,0xa3,0xa4,0xa5,0xa6,0xa7
-	.byte 0xa8,0xa9,0xaa,0xab,0xac,0xad,0xae,0xaf
-	.byte 0xb0,0xb1,0xb2,0xb3,0xb4,0xb5,0xb6,0xb7
-	.byte 0xb8,0xb9,0xba,0xbb,0xbc,0xbd,0xbe,0xbf
-	.byte 0xc0,0x81,0x82,0x83,0x84,0x85,0x86,0x87	# .abcdefg
-	.byte 0x88,0x89,0xca,0xcb,0xcc,0xcd,0xce,0xcf	# hi
-	.byte 0xd0,0x91,0x92,0x93,0x94,0x95,0x96,0x97	# .jklmnop
-	.byte 0x98,0x99,0xda,0xdb,0xdc,0xdd,0xde,0xdf	# qr
-	.byte 0xe0,0xe1,0xa2,0xa3,0xa4,0xa5,0xa6,0xa7	# ..stuvwx
-	.byte 0xa8,0xa9,0xea,0xeb,0xec,0xed,0xee,0xef	# yz
-	.byte 0xf0,0xf1,0xf2,0xf3,0xf4,0xf5,0xf6,0xf7
-	.byte 0xf8,0xf9,0xfa,0xfb,0xfc,0xfd,0xfe,0xff
-
 #
 # startup-code at 0x10000, running in absolute addressing mode
 # this is called either by the ipl loader or directly by PSW restart