Merge tag 'mmc-v4.5' of git://git.linaro.org/people/ulf.hansson/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Optimize boot time by detecting cards simultaneously
   - Make runtime resume default behavior for MMC/SD
   - Enable MMC/SD/SDIO devices to suspend/resume asynchronously
   - Allow more than 8 partitions per card
   - Introduce MMC_CAP2_NO_SDIO to prevent unsupported SDIO commands
   - Support the standard DT wakeup-source property
   - Fix driver strength switching for HS200 and HS400
   - Fix switch command timeout
   - Fix invalid vdd in voltage switch power cycle for SDIO

  MMC host:
   - sdhci: Restore behavior when setting VDD via external regulator
   - sdhci: A couple of changes/fixes related to the dma support
   - sdhci-tegra: Add Tegra210 support
   - sdhci-tegra: Support for UHS-I cards including tuning support
   - sdhci-of-at91: Add PM support
   - sh_mmcif: Rework dma channel handling
   - mvsdio: Delete platform data code path"

* tag 'mmc-v4.5' of git://git.linaro.org/people/ulf.hansson/mmc: (52 commits)
  mmc: dw_mmc: remove the unused quirks
  mmc: sdhci-pci: use to_pci_dev()
  mmc: cb710: use to_platform_device()
  mmc: tegra: use correct accessor for misc ctrl register
  mmc: tegra: enable UHS-I modes
  mmc: tegra: implement UHS tuning
  mmc: tegra: disable SPI_MODE_CLKEN
  mmc: tegra: implement module external clock change
  mmc: sdhci: restore behavior when setting VDD via external regulator
  mmc: It is not an error for the card to be removed while suspended
  mmc: block: Allow more than 8 partitions per card
  mmc: core: Optimize boot time by detecting cards simultaneously
  mmc: dw_mmc: use resource_size_t to store physical address
  mmc: core: fix __mmc_switch timeout caused by preempt
  mmc: usdhi6rol0: handle NULL data in timeout
  mmc: of_mmc_spi: Add IRQF_ONESHOT to interrupt flags
  mmc: mediatek: change some dev_err to dev_dbg
  mmc: enable MMC/SD/SDIO device to suspend/resume asynchronously
  mmc: sdhci: Fix sdhci_runtime_pm_bus_on/off()
  mmc: sdhci: 64-bit DMA actually has 4-byte alignment
  ...

Documentation/devicetree/bindings/mmc/renesas,mmcif.txt

@@ -11,6 +11,7 @@ Required properties:
 	- "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs
 	- "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs
 	- "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs
+	- "renesas,mmcif-r8a7793" for the MMCIF found in r8a7793 SoCs
 	- "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs
 
 - clocks: reference to the functional clock

MAINTAINERS

@@ -1896,7 +1896,6 @@ ATMEL AT91 / AT32 MCI DRIVER
 M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 S:	Maintained
 F:	drivers/mmc/host/atmel-mci.c
-F:	drivers/mmc/host/atmel-mci-regs.h
 
 ATMEL AT91 / AT32 SERIAL DRIVER
 M:	Nicolas Ferre <nicolas.ferre@atmel.com>

drivers/mmc/card/block.c

@@ -171,11 +171,7 @@ static struct mmc_blk_data *mmc_blk_get(struct gendisk *disk)
 
 static inline int mmc_get_devidx(struct gendisk *disk)
 {
-	int devmaj = MAJOR(disk_devt(disk));
-	int devidx = MINOR(disk_devt(disk)) / perdev_minors;
-
-	if (!devmaj)
-		devidx = disk->first_minor / perdev_minors;
+	int devidx = disk->first_minor / perdev_minors;
 	return devidx;
 }
 
@@ -344,7 +340,7 @@ static struct mmc_blk_ioc_data *mmc_blk_ioctl_copy_from_user(
 	struct mmc_blk_ioc_data *idata;
 	int err;
 
-	idata = kzalloc(sizeof(*idata), GFP_KERNEL);
+	idata = kmalloc(sizeof(*idata), GFP_KERNEL);
 	if (!idata) {
 		err = -ENOMEM;
 		goto out;
@@ -364,7 +360,7 @@ static struct mmc_blk_ioc_data *mmc_blk_ioctl_copy_from_user(
 	if (!idata->buf_bytes)
 		return idata;
 
-	idata->buf = kzalloc(idata->buf_bytes, GFP_KERNEL);
+	idata->buf = kmalloc(idata->buf_bytes, GFP_KERNEL);
 	if (!idata->buf) {
 		err = -ENOMEM;
 		goto idata_err;
@@ -2244,6 +2240,7 @@ static struct mmc_blk_data *mmc_blk_alloc_req(struct mmc_card *card,
 	md->disk->queue = md->queue.queue;
 	md->disk->driverfs_dev = parent;
 	set_disk_ro(md->disk, md->read_only || default_ro);
+	md->disk->flags = GENHD_FL_EXT_DEVT;
 	if (area_type & (MMC_BLK_DATA_AREA_RPMB | MMC_BLK_DATA_AREA_BOOT))
 		md->disk->flags |= GENHD_FL_NO_PART_SCAN;
 

drivers/mmc/core/bus.c

@@ -349,6 +349,8 @@ int mmc_add_card(struct mmc_card *card)
 
 	card->dev.of_node = mmc_of_find_child_device(card->host, 0);
 
+	device_enable_async_suspend(&card->dev);
+
 	ret = device_add(&card->dev);
 	if (ret)
 		return ret;

drivers/mmc/core/core.c

@@ -55,7 +55,6 @@
  */
 #define MMC_BKOPS_MAX_TIMEOUT	(4 * 60 * 1000) /* max time to wait in ms */
 
-static struct workqueue_struct *workqueue;
 static const unsigned freqs[] = { 400000, 300000, 200000, 100000 };
 
 /*
@@ -66,21 +65,16 @@ static const unsigned freqs[] = { 400000, 300000, 200000, 100000 };
 bool use_spi_crc = 1;
 module_param(use_spi_crc, bool, 0);
 
-/*
- * Internal function. Schedule delayed work in the MMC work queue.
- */
 static int mmc_schedule_delayed_work(struct delayed_work *work,
 				     unsigned long delay)
 {
-	return queue_delayed_work(workqueue, work, delay);
-}
-
-/*
- * Internal function. Flush all scheduled work from the MMC work queue.
+	/*
+	 * We use the system_freezable_wq, because of two reasons.
+	 * First, it allows several works (not the same work item) to be
+	 * executed simultaneously. Second, the queue becomes frozen when
+	 * userspace becomes frozen during system PM.
 	 */
-static void mmc_flush_scheduled_work(void)
-{
-	flush_workqueue(workqueue);
+	return queue_delayed_work(system_freezable_wq, work, delay);
 }
 
 #ifdef CONFIG_FAIL_MMC_REQUEST
@@ -1485,7 +1479,7 @@ int mmc_regulator_get_supply(struct mmc_host *mmc)
 	if (IS_ERR(mmc->supply.vmmc)) {
 		if (PTR_ERR(mmc->supply.vmmc) == -EPROBE_DEFER)
 			return -EPROBE_DEFER;
-		dev_info(dev, "No vmmc regulator found\n");
+		dev_dbg(dev, "No vmmc regulator found\n");
 	} else {
 		ret = mmc_regulator_get_ocrmask(mmc->supply.vmmc);
 		if (ret > 0)
@@ -1497,7 +1491,7 @@ int mmc_regulator_get_supply(struct mmc_host *mmc)
 	if (IS_ERR(mmc->supply.vqmmc)) {
 		if (PTR_ERR(mmc->supply.vqmmc) == -EPROBE_DEFER)
 			return -EPROBE_DEFER;
-		dev_info(dev, "No vqmmc regulator found\n");
+		dev_dbg(dev, "No vqmmc regulator found\n");
 	}
 
 	return 0;
@@ -2476,15 +2470,20 @@ static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq)
 	 * sdio_reset sends CMD52 to reset card.  Since we do not know
 	 * if the card is being re-initialized, just send it.  CMD52
 	 * should be ignored by SD/eMMC cards.
+	 * Skip it if we already know that we do not support SDIO commands
 	 */
+	if (!(host->caps2 & MMC_CAP2_NO_SDIO))
 		sdio_reset(host);
+
 	mmc_go_idle(host);
 
 	mmc_send_if_cond(host, host->ocr_avail);
 
 	/* Order's important: probe SDIO, then SD, then MMC */
+	if (!(host->caps2 & MMC_CAP2_NO_SDIO))
 		if (!mmc_attach_sdio(host))
 			return 0;
+
 	if (!mmc_attach_sd(host))
 		return 0;
 	if (!mmc_attach_mmc(host))
@@ -2498,9 +2497,6 @@ int _mmc_detect_card_removed(struct mmc_host *host)
 {
 	int ret;
 
-	if (host->caps & MMC_CAP_NONREMOVABLE)
-		return 0;
-
 	if (!host->card || mmc_card_removed(host->card))
 		return 1;
 
@@ -2536,6 +2532,9 @@ int mmc_detect_card_removed(struct mmc_host *host)
 	if (!card)
 		return 1;
 
+	if (host->caps & MMC_CAP_NONREMOVABLE)
+		return 0;
+
 	ret = mmc_card_removed(card);
 	/*
 	 * The card will be considered unchanged unless we have been asked to
@@ -2567,11 +2566,6 @@ void mmc_rescan(struct work_struct *work)
 		container_of(work, struct mmc_host, detect.work);
 	int i;
 
-	if (host->trigger_card_event && host->ops->card_event) {
-		host->ops->card_event(host);
-		host->trigger_card_event = false;
-	}
-
 	if (host->rescan_disable)
 		return;
 
@@ -2580,6 +2574,13 @@ void mmc_rescan(struct work_struct *work)
 		return;
 	host->rescan_entered = 1;
 
+	if (host->trigger_card_event && host->ops->card_event) {
+		mmc_claim_host(host);
+		host->ops->card_event(host);
+		mmc_release_host(host);
+		host->trigger_card_event = false;
+	}
+
 	mmc_bus_get(host);
 
 	/*
@@ -2611,15 +2612,14 @@ void mmc_rescan(struct work_struct *work)
 	 */
 	mmc_bus_put(host);
 
+	mmc_claim_host(host);
 	if (!(host->caps & MMC_CAP_NONREMOVABLE) && host->ops->get_cd &&
 			host->ops->get_cd(host) == 0) {
-		mmc_claim_host(host);
 		mmc_power_off(host);
 		mmc_release_host(host);
 		goto out;
 	}
 
-	mmc_claim_host(host);
 	for (i = 0; i < ARRAY_SIZE(freqs); i++) {
 		if (!mmc_rescan_try_freq(host, max(freqs[i], host->f_min)))
 			break;
@@ -2663,7 +2663,6 @@ void mmc_stop_host(struct mmc_host *host)
 
 	host->rescan_disable = 1;
 	cancel_delayed_work_sync(&host->detect);
-	mmc_flush_scheduled_work();
 
 	/* clear pm flags now and let card drivers set them as needed */
 	host->pm_flags = 0;
@@ -2759,13 +2758,12 @@ int mmc_flush_cache(struct mmc_card *card)
 }
 EXPORT_SYMBOL(mmc_flush_cache);
 
-#ifdef CONFIG_PM
-
+#ifdef CONFIG_PM_SLEEP
 /* Do the card removal on suspend if card is assumed removeable
  * Do that in pm notifier while userspace isn't yet frozen, so we will be able
    to sync the card.
 */
-int mmc_pm_notify(struct notifier_block *notify_block,
+static int mmc_pm_notify(struct notifier_block *notify_block,
 			unsigned long mode, void *unused)
 {
 	struct mmc_host *host = container_of(
@@ -2813,6 +2811,17 @@ int mmc_pm_notify(struct notifier_block *notify_block,
 
 	return 0;
 }
+
+void mmc_register_pm_notifier(struct mmc_host *host)
+{
+	host->pm_notify.notifier_call = mmc_pm_notify;
+	register_pm_notifier(&host->pm_notify);
+}
+
+void mmc_unregister_pm_notifier(struct mmc_host *host)
+{
+	unregister_pm_notifier(&host->pm_notify);
+}
 #endif
 
 /**
@@ -2836,13 +2845,9 @@ static int __init mmc_init(void)
 {
 	int ret;
 
-	workqueue = alloc_ordered_workqueue("kmmcd", 0);
-	if (!workqueue)
-		return -ENOMEM;
-
 	ret = mmc_register_bus();
 	if (ret)
-		goto destroy_workqueue;
+		return ret;
 
 	ret = mmc_register_host_class();
 	if (ret)
@@ -2858,9 +2863,6 @@ static int __init mmc_init(void)
 	mmc_unregister_host_class();
 unregister_bus:
 	mmc_unregister_bus();
-destroy_workqueue:
-	destroy_workqueue(workqueue);
-
 	return ret;
 }
 
@@ -2869,7 +2871,6 @@ static void __exit mmc_exit(void)
 	sdio_unregister_bus();
 	mmc_unregister_host_class();
 	mmc_unregister_bus();
-	destroy_workqueue(workqueue);
 }
 
 subsys_initcall(mmc_init);

drivers/mmc/core/core.h

@@ -90,5 +90,13 @@ int mmc_execute_tuning(struct mmc_card *card);
 int mmc_hs200_to_hs400(struct mmc_card *card);
 int mmc_hs400_to_hs200(struct mmc_card *card);
 
+#ifdef CONFIG_PM_SLEEP
+void mmc_register_pm_notifier(struct mmc_host *host);
+void mmc_unregister_pm_notifier(struct mmc_host *host);
+#else
+static inline void mmc_register_pm_notifier(struct mmc_host *host) { }
+static inline void mmc_unregister_pm_notifier(struct mmc_host *host) { }
+#endif
+
 #endif
 

drivers/mmc/core/host.c

@@ -21,7 +21,6 @@
 #include <linux/export.h>
 #include <linux/leds.h>
 #include <linux/slab.h>
-#include <linux/suspend.h>
 
 #include <linux/mmc/host.h>
 #include <linux/mmc/card.h>
@@ -275,7 +274,8 @@ int mmc_of_parse(struct mmc_host *host)
 		host->caps2 |= MMC_CAP2_FULL_PWR_CYCLE;
 	if (of_property_read_bool(np, "keep-power-in-suspend"))
 		host->pm_caps |= MMC_PM_KEEP_POWER;
-	if (of_property_read_bool(np, "enable-sdio-wakeup"))
+	if (of_property_read_bool(np, "wakeup-source") ||
+	    of_property_read_bool(np, "enable-sdio-wakeup")) /* legacy */
 		host->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
 	if (of_property_read_bool(np, "mmc-ddr-1_8v"))
 		host->caps |= MMC_CAP_1_8V_DDR;
@@ -348,9 +348,6 @@ struct mmc_host *mmc_alloc_host(int extra, struct device *dev)
 	spin_lock_init(&host->lock);
 	init_waitqueue_head(&host->wq);
 	INIT_DELAYED_WORK(&host->detect, mmc_rescan);
-#ifdef CONFIG_PM
-	host->pm_notify.notifier_call = mmc_pm_notify;
-#endif
 	setup_timer(&host->retune_timer, mmc_retune_timer, (unsigned long)host);
 
 	/*
@@ -395,7 +392,7 @@ int mmc_add_host(struct mmc_host *host)
 #endif
 
 	mmc_start_host(host);
-	register_pm_notifier(&host->pm_notify);
+	mmc_register_pm_notifier(host);
 
 	return 0;
 }
@@ -412,7 +409,7 @@ EXPORT_SYMBOL(mmc_add_host);
  */
 void mmc_remove_host(struct mmc_host *host)
 {
-	unregister_pm_notifier(&host->pm_notify);
+	mmc_unregister_pm_notifier(host);
 	mmc_stop_host(host);
 
 #ifdef CONFIG_DEBUG_FS

drivers/mmc/core/mmc.c

@@ -1076,8 +1076,7 @@ static int mmc_select_hs400(struct mmc_card *card)
 	mmc_set_clock(host, max_dtr);
 
 	/* Switch card to HS mode */
-	val = EXT_CSD_TIMING_HS |
-	      card->drive_strength << EXT_CSD_DRV_STR_SHIFT;
+	val = EXT_CSD_TIMING_HS;
 	err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
 			   EXT_CSD_HS_TIMING, val,
 			   card->ext_csd.generic_cmd6_time,
@@ -1160,8 +1159,7 @@ int mmc_hs400_to_hs200(struct mmc_card *card)
 	mmc_set_clock(host, max_dtr);
 
 	/* Switch HS400 to HS DDR */
-	val = EXT_CSD_TIMING_HS |
-	      card->drive_strength << EXT_CSD_DRV_STR_SHIFT;
+	val = EXT_CSD_TIMING_HS;
 	err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING,
 			   val, card->ext_csd.generic_cmd6_time,
 			   true, send_status, true);
@@ -1907,16 +1905,8 @@ static int mmc_shutdown(struct mmc_host *host)
  */
 static int mmc_resume(struct mmc_host *host)
 {
-	int err = 0;
-
-	if (!(host->caps & MMC_CAP_RUNTIME_RESUME)) {
-		err = _mmc_resume(host);
-		pm_runtime_set_active(&host->card->dev);
-		pm_runtime_mark_last_busy(&host->card->dev);
-	}
 	pm_runtime_enable(&host->card->dev);
-
-	return err;
+	return 0;
 }
 
 /*
@@ -1944,12 +1934,9 @@ static int mmc_runtime_resume(struct mmc_host *host)
 {
 	int err;
 
-	if (!(host->caps & (MMC_CAP_AGGRESSIVE_PM | MMC_CAP_RUNTIME_RESUME)))
-		return 0;
-
 	err = _mmc_resume(host);
-	if (err)
-		pr_err("%s: error %d doing aggressive resume\n",
+	if (err && err != -ENOMEDIUM)
+		pr_err("%s: error %d doing runtime resume\n",
 			mmc_hostname(host), err);
 
 	return 0;

drivers/mmc/core/mmc_ops.c

@@ -489,6 +489,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
 	unsigned long timeout;
 	u32 status = 0;
 	bool use_r1b_resp = use_busy_signal;
+	bool expired = false;
 
 	mmc_retune_hold(host);
 
@@ -545,6 +546,12 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
 	timeout = jiffies + msecs_to_jiffies(timeout_ms);
 	do {
 		if (send_status) {
+			/*
+			 * Due to the possibility of being preempted after
+			 * sending the status command, check the expiration
+			 * time first.
+			 */
+			expired = time_after(jiffies, timeout);
 			err = __mmc_send_status(card, &status, ignore_crc);
 			if (err)
 				goto out;
@@ -565,7 +572,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value,
 		}
 
 		/* Timeout if the device never leaves the program state. */
-		if (time_after(jiffies, timeout)) {
+		if (expired && R1_CURRENT_STATE(status) == R1_STATE_PRG) {
 			pr_err("%s: Card stuck in programming state! %s\n",
 				mmc_hostname(host), __func__);
 			err = -ETIMEDOUT;

drivers/mmc/core/pwrseq.h

@@ -16,7 +16,7 @@ struct mmc_pwrseq_ops {
 };
 
 struct mmc_pwrseq {
-	struct mmc_pwrseq_ops *ops;
+	const struct mmc_pwrseq_ops *ops;
 };
 
 #ifdef CONFIG_OF

drivers/mmc/core/pwrseq_emmc.c

@@ -51,7 +51,7 @@ static void mmc_pwrseq_emmc_free(struct mmc_host *host)
 	kfree(pwrseq);
 }
 
-static struct mmc_pwrseq_ops mmc_pwrseq_emmc_ops = {
+static const struct mmc_pwrseq_ops mmc_pwrseq_emmc_ops = {
 	.post_power_on = mmc_pwrseq_emmc_reset,
 	.free = mmc_pwrseq_emmc_free,
 };

drivers/mmc/core/pwrseq_simple.c

@@ -87,7 +87,7 @@ static void mmc_pwrseq_simple_free(struct mmc_host *host)
 	kfree(pwrseq);
 }
 
-static struct mmc_pwrseq_ops mmc_pwrseq_simple_ops = {
+static const struct mmc_pwrseq_ops mmc_pwrseq_simple_ops = {
 	.pre_power_on = mmc_pwrseq_simple_pre_power_on,
 	.post_power_on = mmc_pwrseq_simple_post_power_on,
 	.power_off = mmc_pwrseq_simple_power_off,

drivers/mmc/core/sd.c

@@ -1128,16 +1128,8 @@ static int _mmc_sd_resume(struct mmc_host *host)
  */
 static int mmc_sd_resume(struct mmc_host *host)
 {
-	int err = 0;
-
-	if (!(host->caps & MMC_CAP_RUNTIME_RESUME)) {
-		err = _mmc_sd_resume(host);
-		pm_runtime_set_active(&host->card->dev);
-		pm_runtime_mark_last_busy(&host->card->dev);
-	}
 	pm_runtime_enable(&host->card->dev);
-
-	return err;
+	return 0;
 }
 
 /*
@@ -1165,12 +1157,9 @@ static int mmc_sd_runtime_resume(struct mmc_host *host)
 {
 	int err;
 
-	if (!(host->caps & (MMC_CAP_AGGRESSIVE_PM | MMC_CAP_RUNTIME_RESUME)))
-		return 0;
-
 	err = _mmc_sd_resume(host);
-	if (err)
-		pr_err("%s: error %d doing aggressive resume\n",
+	if (err && err != -ENOMEDIUM)
+		pr_err("%s: error %d doing runtime resume\n",
 			mmc_hostname(host), err);
 
 	return 0;

drivers/mmc/core/sdio.c

@@ -630,7 +630,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
 	 */
 	if (!powered_resume && (rocr & ocr & R4_18V_PRESENT)) {
 		err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
-					ocr);
+					ocr_card);
 		if (err == -EAGAIN) {
 			sdio_reset(host);
 			mmc_go_idle(host);

drivers/mmc/core/sdio_bus.c

@@ -322,6 +322,7 @@ int sdio_add_func(struct sdio_func *func)
 
 	sdio_set_of_node(func);
 	sdio_acpi_set_handle(func);
+	device_enable_async_suspend(&func->dev);
 	ret = device_add(&func->dev);
 	if (ret == 0)
 		sdio_func_set_present(func);

drivers/mmc/host/Kconfig

@@ -455,6 +455,7 @@ config MMC_TIFM_SD
 config MMC_MVSDIO
 	tristate "Marvell MMC/SD/SDIO host driver"
 	depends on PLAT_ORION
+	depends on OF
 	---help---
 	  This selects the Marvell SDIO host driver.
 	  SDIO may currently be found on the Kirkwood 88F6281 and 88F6192

drivers/mmc/host/atmel-mci-regs.h

-/*
- * Atmel MultiMedia Card Interface driver
- *
- * Copyright (C) 2004-2006 Atmel Corporation
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/*
- * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
- * Registers and bitfields marked with [2] are only available in MCI2
- */
-
-#ifndef __DRIVERS_MMC_ATMEL_MCI_H__
-#define __DRIVERS_MMC_ATMEL_MCI_H__
-
-/* MCI Register Definitions */
-#define ATMCI_CR			0x0000	/* Control */
-# define ATMCI_CR_MCIEN			(  1 <<  0)	/* MCI Enable */
-# define ATMCI_CR_MCIDIS		(  1 <<  1)	/* MCI Disable */
-# define ATMCI_CR_PWSEN			(  1 <<  2)	/* Power Save Enable */
-# define ATMCI_CR_PWSDIS		(  1 <<  3)	/* Power Save Disable */
-# define ATMCI_CR_SWRST			(  1 <<  7)	/* Software Reset */
-#define ATMCI_MR			0x0004	/* Mode */
-# define ATMCI_MR_CLKDIV(x)		((x) <<  0)	/* Clock Divider */
-# define ATMCI_MR_PWSDIV(x)		((x) <<  8)	/* Power Saving Divider */
-# define ATMCI_MR_RDPROOF		(  1 << 11)	/* Read Proof */
-# define ATMCI_MR_WRPROOF		(  1 << 12)	/* Write Proof */
-# define ATMCI_MR_PDCFBYTE		(  1 << 13)	/* Force Byte Transfer */
-# define ATMCI_MR_PDCPADV		(  1 << 14)	/* Padding Value */
-# define ATMCI_MR_PDCMODE		(  1 << 15)	/* PDC-oriented Mode */
-# define ATMCI_MR_CLKODD(x)		((x) << 16)	/* LSB of Clock Divider */
-#define ATMCI_DTOR			0x0008	/* Data Timeout */
-# define ATMCI_DTOCYC(x)		((x) <<  0)	/* Data Timeout Cycles */
-# define ATMCI_DTOMUL(x)		((x) <<  4)	/* Data Timeout Multiplier */
-#define ATMCI_SDCR			0x000c	/* SD Card / SDIO */
-# define ATMCI_SDCSEL_SLOT_A		(  0 <<  0)	/* Select SD slot A */
-# define ATMCI_SDCSEL_SLOT_B		(  1 <<  0)	/* Select SD slot A */
-# define ATMCI_SDCSEL_MASK		(  3 <<  0)
-# define ATMCI_SDCBUS_1BIT		(  0 <<  6)	/* 1-bit data bus */
-# define ATMCI_SDCBUS_4BIT		(  2 <<  6)	/* 4-bit data bus */
-# define ATMCI_SDCBUS_8BIT		(  3 <<  6)	/* 8-bit data bus[2] */
-# define ATMCI_SDCBUS_MASK		(  3 <<  6)
-#define ATMCI_ARGR			0x0010	/* Command Argument */
-#define ATMCI_CMDR			0x0014	/* Command */
-# define ATMCI_CMDR_CMDNB(x)		((x) <<  0)	/* Command Opcode */
-# define ATMCI_CMDR_RSPTYP_NONE		(  0 <<  6)	/* No response */
-# define ATMCI_CMDR_RSPTYP_48BIT	(  1 <<  6)	/* 48-bit response */
-# define ATMCI_CMDR_RSPTYP_136BIT	(  2 <<  6)	/* 136-bit response */
-# define ATMCI_CMDR_SPCMD_INIT		(  1 <<  8)	/* Initialization command */
-# define ATMCI_CMDR_SPCMD_SYNC		(  2 <<  8)	/* Synchronized command */
-# define ATMCI_CMDR_SPCMD_INT		(  4 <<  8)	/* Interrupt command */
-# define ATMCI_CMDR_SPCMD_INTRESP	(  5 <<  8)	/* Interrupt response */
-# define ATMCI_CMDR_OPDCMD		(  1 << 11)	/* Open Drain */
-# define ATMCI_CMDR_MAXLAT_5CYC		(  0 << 12)	/* Max latency 5 cycles */
-# define ATMCI_CMDR_MAXLAT_64CYC	(  1 << 12)	/* Max latency 64 cycles */
-# define ATMCI_CMDR_START_XFER		(  1 << 16)	/* Start data transfer */
-# define ATMCI_CMDR_STOP_XFER		(  2 << 16)	/* Stop data transfer */
-# define ATMCI_CMDR_TRDIR_WRITE		(  0 << 18)	/* Write data */
-# define ATMCI_CMDR_TRDIR_READ		(  1 << 18)	/* Read data */
-# define ATMCI_CMDR_BLOCK		(  0 << 19)	/* Single-block transfer */
-# define ATMCI_CMDR_MULTI_BLOCK		(  1 << 19)	/* Multi-block transfer */
-# define ATMCI_CMDR_STREAM		(  2 << 19)	/* MMC Stream transfer */
-# define ATMCI_CMDR_SDIO_BYTE		(  4 << 19)	/* SDIO Byte transfer */
-# define ATMCI_CMDR_SDIO_BLOCK		(  5 << 19)	/* SDIO Block transfer */
-# define ATMCI_CMDR_SDIO_SUSPEND	(  1 << 24)	/* SDIO Suspend Command */
-# define ATMCI_CMDR_SDIO_RESUME		(  2 << 24)	/* SDIO Resume Command */
-#define ATMCI_BLKR			0x0018	/* Block */
-# define ATMCI_BCNT(x)			((x) <<  0)	/* Data Block Count */
-# define ATMCI_BLKLEN(x)		((x) << 16)	/* Data Block Length */
-#define ATMCI_CSTOR			0x001c	/* Completion Signal Timeout[2] */
-# define ATMCI_CSTOCYC(x)		((x) <<  0)	/* CST cycles */
-# define ATMCI_CSTOMUL(x)		((x) <<  4)	/* CST multiplier */
-#define ATMCI_RSPR			0x0020	/* Response 0 */
-#define ATMCI_RSPR1			0x0024	/* Response 1 */
-#define ATMCI_RSPR2			0x0028	/* Response 2 */
-#define ATMCI_RSPR3			0x002c	/* Response 3 */
-#define ATMCI_RDR			0x0030	/* Receive Data */
-#define ATMCI_TDR			0x0034	/* Transmit Data */
-#define ATMCI_SR			0x0040	/* Status */
-#define ATMCI_IER			0x0044	/* Interrupt Enable */
-#define ATMCI_IDR			0x0048	/* Interrupt Disable */
-#define ATMCI_IMR			0x004c	/* Interrupt Mask */
-# define ATMCI_CMDRDY			(  1 <<   0)	/* Command Ready */
-# define ATMCI_RXRDY			(  1 <<   1)	/* Receiver Ready */
-# define ATMCI_TXRDY			(  1 <<   2)	/* Transmitter Ready */
-# define ATMCI_BLKE			(  1 <<   3)	/* Data Block Ended */
-# define ATMCI_DTIP			(  1 <<   4)	/* Data Transfer In Progress */
-# define ATMCI_NOTBUSY			(  1 <<   5)	/* Data Not Busy */
-# define ATMCI_ENDRX			(  1 <<   6)    /* End of RX Buffer */
-# define ATMCI_ENDTX			(  1 <<   7)    /* End of TX Buffer */
-# define ATMCI_SDIOIRQA			(  1 <<   8)	/* SDIO IRQ in slot A */
-# define ATMCI_SDIOIRQB			(  1 <<   9)	/* SDIO IRQ in slot B */
-# define ATMCI_SDIOWAIT			(  1 <<  12)    /* SDIO Read Wait Operation Status */
-# define ATMCI_CSRCV			(  1 <<  13)    /* CE-ATA Completion Signal Received */
-# define ATMCI_RXBUFF			(  1 <<  14)    /* RX Buffer Full */
-# define ATMCI_TXBUFE			(  1 <<  15)    /* TX Buffer Empty */
-# define ATMCI_RINDE			(  1 <<  16)	/* Response Index Error */
-# define ATMCI_RDIRE			(  1 <<  17)	/* Response Direction Error */
-# define ATMCI_RCRCE			(  1 <<  18)	/* Response CRC Error */
-# define ATMCI_RENDE			(  1 <<  19)	/* Response End Bit Error */
-# define ATMCI_RTOE			(  1 <<  20)	/* Response Time-Out Error */
-# define ATMCI_DCRCE			(  1 <<  21)	/* Data CRC Error */
-# define ATMCI_DTOE			(  1 <<  22)	/* Data Time-Out Error */
-# define ATMCI_CSTOE			(  1 <<  23)    /* Completion Signal Time-out Error */
-# define ATMCI_BLKOVRE			(  1 <<  24)    /* DMA Block Overrun Error */
-# define ATMCI_DMADONE			(  1 <<  25)    /* DMA Transfer Done */
-# define ATMCI_FIFOEMPTY		(  1 <<  26)    /* FIFO Empty Flag */
-# define ATMCI_XFRDONE			(  1 <<  27)    /* Transfer Done Flag */
-# define ATMCI_ACKRCV			(  1 <<  28)    /* Boot Operation Acknowledge Received */
-# define ATMCI_ACKRCVE			(  1 <<  29)    /* Boot Operation Acknowledge Error */
-# define ATMCI_OVRE			(  1 <<  30)	/* RX Overrun Error */
-# define ATMCI_UNRE			(  1 <<  31)	/* TX Underrun Error */
-#define ATMCI_DMA			0x0050	/* DMA Configuration[2] */
-# define ATMCI_DMA_OFFSET(x)		((x) <<  0)	/* DMA Write Buffer Offset */
-# define ATMCI_DMA_CHKSIZE(x)		((x) <<  4)	/* DMA Channel Read and Write Chunk Size */
-# define ATMCI_DMAEN			(  1 <<  8)	/* DMA Hardware Handshaking Enable */
-#define ATMCI_CFG			0x0054	/* Configuration[2] */
-# define ATMCI_CFG_FIFOMODE_1DATA	(  1 <<  0)	/* MCI Internal FIFO control mode */
-# define ATMCI_CFG_FERRCTRL_COR		(  1 <<  4)	/* Flow Error flag reset control mode */
-# define ATMCI_CFG_HSMODE		(  1 <<  8)	/* High Speed Mode */
-# define ATMCI_CFG_LSYNC		(  1 << 12)	/* Synchronize on the last block */
-#define ATMCI_WPMR			0x00e4	/* Write Protection Mode[2] */
-# define ATMCI_WP_EN			(  1 <<  0)	/* WP Enable */
-# define ATMCI_WP_KEY			(0x4d4349 << 8)	/* WP Key */
-#define ATMCI_WPSR			0x00e8	/* Write Protection Status[2] */
-# define ATMCI_GET_WP_VS(x)		((x) & 0x0f)
-# define ATMCI_GET_WP_VSRC(x)		(((x) >> 8) & 0xffff)
-#define ATMCI_VERSION			0x00FC  /* Version */
-#define ATMCI_FIFO_APERTURE		0x0200	/* FIFO Aperture[2] */
-
-/* This is not including the FIFO Aperture on MCI2 */
-#define ATMCI_REGS_SIZE		0x100
-
-/* Register access macros */
-#ifdef CONFIG_AVR32
-#define atmci_readl(port, reg)			\
-	__raw_readl((port)->regs + reg)
-#define atmci_writel(port, reg, value)			\
-	__raw_writel((value), (port)->regs + reg)
-#else
-#define atmci_readl(port, reg)			\
-	readl_relaxed((port)->regs + reg)
-#define atmci_writel(port, reg, value)			\
-	writel_relaxed((value), (port)->regs + reg)
-#endif
-
-/* On AVR chips the Peripheral DMA Controller is not connected to MCI. */
-#ifdef CONFIG_AVR32
-#	define ATMCI_PDC_CONNECTED	0
-#else
-#	define ATMCI_PDC_CONNECTED	1
-#endif
-
-/*
- * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
- * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
- *
- * This can be done by finding most significant bit set.
- */
-static inline unsigned int atmci_convert_chksize(unsigned int maxburst)
-{
-	if (maxburst > 1)
-		return fls(maxburst) - 2;
-	else
-		return 0;
-}
-
-#endif /* __DRIVERS_MMC_ATMEL_MCI_H__ */

drivers/mmc/host/atmel-mci.c

@@ -44,7 +44,141 @@
 #include <asm/io.h>
 #include <asm/unaligned.h>
 
-#include "atmel-mci-regs.h"
+/*
+ * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
+ * Registers and bitfields marked with [2] are only available in MCI2
+ */
+
+/* MCI Register Definitions */
+#define	ATMCI_CR			0x0000	/* Control */
+#define		ATMCI_CR_MCIEN			BIT(0)		/* MCI Enable */
+#define		ATMCI_CR_MCIDIS			BIT(1)		/* MCI Disable */
+#define		ATMCI_CR_PWSEN			BIT(2)		/* Power Save Enable */
+#define		ATMCI_CR_PWSDIS			BIT(3)		/* Power Save Disable */
+#define		ATMCI_CR_SWRST			BIT(7)		/* Software Reset */
+#define	ATMCI_MR			0x0004	/* Mode */
+#define		ATMCI_MR_CLKDIV(x)		((x) <<  0)	/* Clock Divider */
+#define		ATMCI_MR_PWSDIV(x)		((x) <<  8)	/* Power Saving Divider */
+#define		ATMCI_MR_RDPROOF		BIT(11)		/* Read Proof */
+#define		ATMCI_MR_WRPROOF		BIT(12)		/* Write Proof */
+#define		ATMCI_MR_PDCFBYTE		BIT(13)		/* Force Byte Transfer */
+#define		ATMCI_MR_PDCPADV		BIT(14)		/* Padding Value */
+#define		ATMCI_MR_PDCMODE		BIT(15)		/* PDC-oriented Mode */
+#define		ATMCI_MR_CLKODD(x)		((x) << 16)	/* LSB of Clock Divider */
+#define	ATMCI_DTOR			0x0008	/* Data Timeout */
+#define		ATMCI_DTOCYC(x)			((x) <<  0)	/* Data Timeout Cycles */
+#define		ATMCI_DTOMUL(x)			((x) <<  4)	/* Data Timeout Multiplier */
+#define	ATMCI_SDCR			0x000c	/* SD Card / SDIO */
+#define		ATMCI_SDCSEL_SLOT_A		(0 <<  0)	/* Select SD slot A */
+#define		ATMCI_SDCSEL_SLOT_B		(1 <<  0)	/* Select SD slot A */
+#define		ATMCI_SDCSEL_MASK		(3 <<  0)
+#define		ATMCI_SDCBUS_1BIT		(0 <<  6)	/* 1-bit data bus */
+#define		ATMCI_SDCBUS_4BIT		(2 <<  6)	/* 4-bit data bus */
+#define		ATMCI_SDCBUS_8BIT		(3 <<  6)	/* 8-bit data bus[2] */
+#define		ATMCI_SDCBUS_MASK		(3 <<  6)
+#define	ATMCI_ARGR			0x0010	/* Command Argument */
+#define	ATMCI_CMDR			0x0014	/* Command */
+#define		ATMCI_CMDR_CMDNB(x)		((x) <<  0)	/* Command Opcode */
+#define		ATMCI_CMDR_RSPTYP_NONE		(0 <<  6)	/* No response */
+#define		ATMCI_CMDR_RSPTYP_48BIT		(1 <<  6)	/* 48-bit response */
+#define		ATMCI_CMDR_RSPTYP_136BIT	(2 <<  6)	/* 136-bit response */
+#define		ATMCI_CMDR_SPCMD_INIT		(1 <<  8)	/* Initialization command */
+#define		ATMCI_CMDR_SPCMD_SYNC		(2 <<  8)	/* Synchronized command */
+#define		ATMCI_CMDR_SPCMD_INT		(4 <<  8)	/* Interrupt command */
+#define		ATMCI_CMDR_SPCMD_INTRESP	(5 <<  8)	/* Interrupt response */
+#define		ATMCI_CMDR_OPDCMD		(1 << 11)	/* Open Drain */
+#define		ATMCI_CMDR_MAXLAT_5CYC		(0 << 12)	/* Max latency 5 cycles */
+#define		ATMCI_CMDR_MAXLAT_64CYC		(1 << 12)	/* Max latency 64 cycles */
+#define		ATMCI_CMDR_START_XFER		(1 << 16)	/* Start data transfer */
+#define		ATMCI_CMDR_STOP_XFER		(2 << 16)	/* Stop data transfer */
+#define		ATMCI_CMDR_TRDIR_WRITE		(0 << 18)	/* Write data */
+#define		ATMCI_CMDR_TRDIR_READ		(1 << 18)	/* Read data */
+#define		ATMCI_CMDR_BLOCK		(0 << 19)	/* Single-block transfer */
+#define		ATMCI_CMDR_MULTI_BLOCK		(1 << 19)	/* Multi-block transfer */
+#define		ATMCI_CMDR_STREAM		(2 << 19)	/* MMC Stream transfer */
+#define		ATMCI_CMDR_SDIO_BYTE		(4 << 19)	/* SDIO Byte transfer */
+#define		ATMCI_CMDR_SDIO_BLOCK		(5 << 19)	/* SDIO Block transfer */
+#define		ATMCI_CMDR_SDIO_SUSPEND		(1 << 24)	/* SDIO Suspend Command */
+#define		ATMCI_CMDR_SDIO_RESUME		(2 << 24)	/* SDIO Resume Command */
+#define	ATMCI_BLKR			0x0018	/* Block */
+#define		ATMCI_BCNT(x)			((x) <<  0)	/* Data Block Count */
+#define		ATMCI_BLKLEN(x)			((x) << 16)	/* Data Block Length */
+#define	ATMCI_CSTOR			0x001c	/* Completion Signal Timeout[2] */
+#define		ATMCI_CSTOCYC(x)		((x) <<  0)	/* CST cycles */
+#define		ATMCI_CSTOMUL(x)		((x) <<  4)	/* CST multiplier */
+#define	ATMCI_RSPR			0x0020	/* Response 0 */
+#define	ATMCI_RSPR1			0x0024	/* Response 1 */
+#define	ATMCI_RSPR2			0x0028	/* Response 2 */
+#define	ATMCI_RSPR3			0x002c	/* Response 3 */
+#define	ATMCI_RDR			0x0030	/* Receive Data */
+#define	ATMCI_TDR			0x0034	/* Transmit Data */
+#define	ATMCI_SR			0x0040	/* Status */
+#define	ATMCI_IER			0x0044	/* Interrupt Enable */
+#define	ATMCI_IDR			0x0048	/* Interrupt Disable */
+#define	ATMCI_IMR			0x004c	/* Interrupt Mask */
+#define		ATMCI_CMDRDY			BIT(0)		/* Command Ready */
+#define		ATMCI_RXRDY			BIT(1)		/* Receiver Ready */
+#define		ATMCI_TXRDY			BIT(2)		/* Transmitter Ready */
+#define		ATMCI_BLKE			BIT(3)		/* Data Block Ended */
+#define		ATMCI_DTIP			BIT(4)		/* Data Transfer In Progress */
+#define		ATMCI_NOTBUSY			BIT(5)		/* Data Not Busy */
+#define		ATMCI_ENDRX			BIT(6)		/* End of RX Buffer */
+#define		ATMCI_ENDTX			BIT(7)		/* End of TX Buffer */
+#define		ATMCI_SDIOIRQA			BIT(8)		/* SDIO IRQ in slot A */
+#define		ATMCI_SDIOIRQB			BIT(9)		/* SDIO IRQ in slot B */
+#define		ATMCI_SDIOWAIT			BIT(12)		/* SDIO Read Wait Operation Status */
+#define		ATMCI_CSRCV			BIT(13)		/* CE-ATA Completion Signal Received */
+#define		ATMCI_RXBUFF			BIT(14)		/* RX Buffer Full */
+#define		ATMCI_TXBUFE			BIT(15)		/* TX Buffer Empty */
+#define		ATMCI_RINDE			BIT(16)		/* Response Index Error */
+#define		ATMCI_RDIRE			BIT(17)		/* Response Direction Error */
+#define		ATMCI_RCRCE			BIT(18)		/* Response CRC Error */
+#define		ATMCI_RENDE			BIT(19)		/* Response End Bit Error */
+#define		ATMCI_RTOE			BIT(20)		/* Response Time-Out Error */
+#define		ATMCI_DCRCE			BIT(21)		/* Data CRC Error */
+#define		ATMCI_DTOE			BIT(22)		/* Data Time-Out Error */
+#define		ATMCI_CSTOE			BIT(23)		/* Completion Signal Time-out Error */
+#define		ATMCI_BLKOVRE			BIT(24)		/* DMA Block Overrun Error */
+#define		ATMCI_DMADONE			BIT(25)		/* DMA Transfer Done */
+#define		ATMCI_FIFOEMPTY			BIT(26)		/* FIFO Empty Flag */
+#define		ATMCI_XFRDONE			BIT(27)		/* Transfer Done Flag */
+#define		ATMCI_ACKRCV			BIT(28)		/* Boot Operation Acknowledge Received */
+#define		ATMCI_ACKRCVE			BIT(29)		/* Boot Operation Acknowledge Error */
+#define		ATMCI_OVRE			BIT(30)		/* RX Overrun Error */
+#define		ATMCI_UNRE			BIT(31)		/* TX Underrun Error */
+#define	ATMCI_DMA			0x0050	/* DMA Configuration[2] */
+#define		ATMCI_DMA_OFFSET(x)		((x) <<  0)	/* DMA Write Buffer Offset */
+#define		ATMCI_DMA_CHKSIZE(x)		((x) <<  4)	/* DMA Channel Read and Write Chunk Size */
+#define		ATMCI_DMAEN			BIT(8)	/* DMA Hardware Handshaking Enable */
+#define	ATMCI_CFG			0x0054	/* Configuration[2] */
+#define		ATMCI_CFG_FIFOMODE_1DATA	BIT(0)		/* MCI Internal FIFO control mode */
+#define		ATMCI_CFG_FERRCTRL_COR		BIT(4)		/* Flow Error flag reset control mode */
+#define		ATMCI_CFG_HSMODE		BIT(8)		/* High Speed Mode */
+#define		ATMCI_CFG_LSYNC			BIT(12)		/* Synchronize on the last block */
+#define	ATMCI_WPMR			0x00e4	/* Write Protection Mode[2] */
+#define		ATMCI_WP_EN			BIT(0)		/* WP Enable */
+#define		ATMCI_WP_KEY			(0x4d4349 << 8)	/* WP Key */
+#define	ATMCI_WPSR			0x00e8	/* Write Protection Status[2] */
+#define		ATMCI_GET_WP_VS(x)		((x) & 0x0f)
+#define		ATMCI_GET_WP_VSRC(x)		(((x) >> 8) & 0xffff)
+#define	ATMCI_VERSION			0x00FC  /* Version */
+#define	ATMCI_FIFO_APERTURE		0x0200	/* FIFO Aperture[2] */
+
+/* This is not including the FIFO Aperture on MCI2 */
+#define	ATMCI_REGS_SIZE		0x100
+
+/* Register access macros */
+#define	atmci_readl(port, reg)				\
+	__raw_readl((port)->regs + reg)
+#define	atmci_writel(port, reg, value)			\
+	__raw_writel((value), (port)->regs + reg)
+
+/* On AVR chips the Peripheral DMA Controller is not connected to MCI. */
+#ifdef CONFIG_AVR32
+#	define ATMCI_PDC_CONNECTED	0
+#else
+#	define ATMCI_PDC_CONNECTED	1
+#endif
 
 #define AUTOSUSPEND_DELAY	50
 
@@ -584,6 +718,29 @@ static inline unsigned int atmci_get_version(struct atmel_mci *host)
 	return atmci_readl(host, ATMCI_VERSION) & 0x00000fff;
 }
 
+/*
+ * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
+ * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
+ * With version 0x600, we need to convert them as: 1 -> 0, 2 -> 1, 4 -> 2,
+ * 8 -> 3, 16 -> 4.
+ *
+ * This can be done by finding most significant bit set.
+ */
+static inline unsigned int atmci_convert_chksize(struct atmel_mci *host,
+						 unsigned int maxburst)
+{
+	unsigned int version = atmci_get_version(host);
+	unsigned int offset = 2;
+
+	if (version >= 0x600)
+		offset = 1;
+
+	if (maxburst > 1)
+		return fls(maxburst) - offset;
+	else
+		return 0;
+}
+
 static void atmci_timeout_timer(unsigned long data)
 {
 	struct atmel_mci *host;
@@ -1034,11 +1191,13 @@ atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
 	if (data->flags & MMC_DATA_READ) {
 		direction = DMA_FROM_DEVICE;
 		host->dma_conf.direction = slave_dirn = DMA_DEV_TO_MEM;
-		maxburst = atmci_convert_chksize(host->dma_conf.src_maxburst);
+		maxburst = atmci_convert_chksize(host,
+						 host->dma_conf.src_maxburst);
 	} else {
 		direction = DMA_TO_DEVICE;
 		host->dma_conf.direction = slave_dirn = DMA_MEM_TO_DEV;
-		maxburst = atmci_convert_chksize(host->dma_conf.dst_maxburst);
+		maxburst = atmci_convert_chksize(host,
+						 host->dma_conf.dst_maxburst);
 	}
 
 	if (host->caps.has_dma_conf_reg)

drivers/mmc/host/cb710-mmc.h

@@ -29,8 +29,7 @@ static inline struct mmc_host *cb710_slot_to_mmc(struct cb710_slot *slot)
 
 static inline struct cb710_slot *cb710_mmc_to_slot(struct mmc_host *mmc)
 {
-	struct platform_device *pdev = container_of(mmc_dev(mmc),
-		struct platform_device, dev);
+	struct platform_device *pdev = to_platform_device(mmc_dev(mmc));
 	return cb710_pdev_to_slot(pdev);
 }
 

drivers/mmc/host/dw_mmc-pltfm.c

@@ -60,7 +60,7 @@ int dw_mci_pltfm_register(struct platform_device *pdev,
 
 	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	/* Get registers' physical base address */
-	host->phy_regs = (void *)(regs->start);
+	host->phy_regs = regs->start;
 	host->regs = devm_ioremap_resource(&pdev->dev, regs);
 	if (IS_ERR(host->regs))
 		return PTR_ERR(host->regs);

drivers/mmc/host/dw_mmc-rockchip.c

@@ -239,20 +239,12 @@ static int dw_mci_rockchip_init(struct dw_mci *host)
 	return 0;
 }
 
-/* Common capabilities of RK3288 SoC */
-static unsigned long dw_mci_rk3288_dwmmc_caps[4] = {
-	MMC_CAP_RUNTIME_RESUME, /* emmc */
-	MMC_CAP_RUNTIME_RESUME, /* sdmmc */
-	MMC_CAP_RUNTIME_RESUME, /* sdio0 */
-	MMC_CAP_RUNTIME_RESUME, /* sdio1 */
-};
 static const struct dw_mci_drv_data rk2928_drv_data = {
 	.prepare_command        = dw_mci_rockchip_prepare_command,
 	.init			= dw_mci_rockchip_init,
 };
 
 static const struct dw_mci_drv_data rk3288_drv_data = {
-	.caps			= dw_mci_rk3288_dwmmc_caps,
 	.prepare_command        = dw_mci_rockchip_prepare_command,
 	.set_ios		= dw_mci_rk3288_set_ios,
 	.execute_tuning		= dw_mci_rk3288_execute_tuning,

drivers/mmc/host/dw_mmc.c

@@ -699,7 +699,7 @@ static int dw_mci_edmac_start_dma(struct dw_mci *host,
 	int ret = 0;
 
 	/* Set external dma config: burst size, burst width */
-	cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
+	cfg.dst_addr = host->phy_regs + fifo_offset;
 	cfg.src_addr = cfg.dst_addr;
 	cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
 	cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
@@ -1634,12 +1634,6 @@ static int dw_mci_command_complete(struct dw_mci *host, struct mmc_command *cmd)
 	else
 		cmd->error = 0;
 
-	if (cmd->error) {
-		/* newer ip versions need a delay between retries */
-		if (host->quirks & DW_MCI_QUIRK_RETRY_DELAY)
-			mdelay(20);
-	}
-
 	return cmd->error;
 }
 
@@ -2355,16 +2349,6 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
 
 	pending = mci_readl(host, MINTSTS); /* read-only mask reg */
 
-	/*
-	 * DTO fix - version 2.10a and below, and only if internal DMA
-	 * is configured.
-	 */
-	if (host->quirks & DW_MCI_QUIRK_IDMAC_DTO) {
-		if (!pending &&
-		    ((mci_readl(host, STATUS) >> 17) & 0x1fff))
-			pending |= SDMMC_INT_DATA_OVER;
-	}
-
 	if (pending) {
 		/* Check volt switch first, since it can look like an error */
 		if ((host->state == STATE_SENDING_CMD11) &&
@@ -3165,9 +3149,6 @@ int dw_mci_probe(struct dw_mci *host)
 	/* Now that slots are all setup, we can enable card detect */
 	dw_mci_enable_cd(host);
 
-	if (host->quirks & DW_MCI_QUIRK_IDMAC_DTO)
-		dev_info(host->dev, "Internal DMAC interrupt fix enabled.\n");
-
 	return 0;
 
 err_dmaunmap:

drivers/mmc/host/mtk-sd.c

@@ -972,7 +972,7 @@ static bool msdc_data_xfer_done(struct msdc_host *host, u32 events,
 		if ((events & MSDC_INT_XFER_COMPL) && (!stop || !stop->error)) {
 			data->bytes_xfered = data->blocks * data->blksz;
 		} else {
-			dev_err(host->dev, "interrupt events: %x\n", events);
+			dev_dbg(host->dev, "interrupt events: %x\n", events);
 			msdc_reset_hw(host);
 			host->error |= REQ_DAT_ERR;
 			data->bytes_xfered = 0;
@@ -982,9 +982,9 @@ static bool msdc_data_xfer_done(struct msdc_host *host, u32 events,
 			else if (events & MSDC_INT_DATCRCERR)
 				data->error = -EILSEQ;
 
-			dev_err(host->dev, "%s: cmd=%d; blocks=%d",
+			dev_dbg(host->dev, "%s: cmd=%d; blocks=%d",
 				__func__, mrq->cmd->opcode, data->blocks);
-			dev_err(host->dev, "data_error=%d xfer_size=%d\n",
+			dev_dbg(host->dev, "data_error=%d xfer_size=%d\n",
 				(int)data->error, data->bytes_xfered);
 		}
 
@@ -1543,7 +1543,6 @@ static int msdc_drv_probe(struct platform_device *pdev)
 	mmc->f_min = host->src_clk_freq / (4 * 255);
 
 	mmc->caps |= MMC_CAP_ERASE | MMC_CAP_CMD23;
-	mmc->caps |= MMC_CAP_RUNTIME_RESUME;
 	/* MMC core transfer sizes tunable parameters */
 	mmc->max_segs = MAX_BD_NUM;
 	mmc->max_seg_size = BDMA_DESC_BUFLEN;

drivers/mmc/host/mvsdio.c

@@ -20,15 +20,12 @@
 #include <linux/scatterlist.h>
 #include <linux/irq.h>
 #include <linux/clk.h>
-#include <linux/gpio.h>
-#include <linux/of_gpio.h>
 #include <linux/of_irq.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/slot-gpio.h>
 
 #include <asm/sizes.h>
 #include <asm/unaligned.h>
-#include <linux/platform_data/mmc-mvsdio.h>
 
 #include "mvsdio.h"
 
@@ -704,6 +701,10 @@ static int mvsd_probe(struct platform_device *pdev)
 	struct resource *r;
 	int ret, irq;
 
+	if (!np) {
+		dev_err(&pdev->dev, "no DT node\n");
+		return -ENODEV;
+	}
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	irq = platform_get_irq(pdev, 0);
 	if (!r || irq < 0)
@@ -727,7 +728,11 @@ static int mvsd_probe(struct platform_device *pdev)
 	 * fixed rate clock).
 	 */
 	host->clk = devm_clk_get(&pdev->dev, NULL);
-	if (!IS_ERR(host->clk))
+	if (IS_ERR(host->clk)) {
+		dev_err(&pdev->dev, "no clock associated\n");
+		ret = -EINVAL;
+		goto out;
+	}
 	clk_prepare_enable(host->clk);
 
 	mmc->ops = &mvsd_ops;
@@ -744,45 +749,10 @@ static int mvsd_probe(struct platform_device *pdev)
 	mmc->max_seg_size = mmc->max_blk_size * mmc->max_blk_count;
 	mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
 
-	if (np) {
-		if (IS_ERR(host->clk)) {
-			dev_err(&pdev->dev, "DT platforms must have a clock associated\n");
-			ret = -EINVAL;
-			goto out;
-		}
-
 	host->base_clock = clk_get_rate(host->clk) / 2;
 	ret = mmc_of_parse(mmc);
 	if (ret < 0)
 		goto out;
-	} else {
-		const struct mvsdio_platform_data *mvsd_data;
-
-		mvsd_data = pdev->dev.platform_data;
-		if (!mvsd_data) {
-			ret = -ENXIO;
-			goto out;
-		}
-		mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ |
-			    MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
-		host->base_clock = mvsd_data->clock / 2;
-		/* GPIO 0 regarded as invalid for backward compatibility */
-		if (mvsd_data->gpio_card_detect &&
-		    gpio_is_valid(mvsd_data->gpio_card_detect)) {
-			ret = mmc_gpio_request_cd(mmc,
-						  mvsd_data->gpio_card_detect,
-						  0);
-			if (ret)
-				goto out;
-		} else {
-			mmc->caps |= MMC_CAP_NEEDS_POLL;
-		}
-
-		if (mvsd_data->gpio_write_protect &&
-		    gpio_is_valid(mvsd_data->gpio_write_protect))
-			mmc_gpio_request_ro(mmc, mvsd_data->gpio_write_protect);
-	}
-
 	if (maxfreq)
 		mmc->f_max = maxfreq;
 

drivers/mmc/host/of_mmc_spi.c

@@ -55,8 +55,8 @@ static int of_mmc_spi_init(struct device *dev,
 {
 	struct of_mmc_spi *oms = to_of_mmc_spi(dev);
 
-	return request_threaded_irq(oms->detect_irq, NULL, irqhandler, 0,
-				    dev_name(dev), mmc);
+	return request_threaded_irq(oms->detect_irq, NULL, irqhandler,
+					IRQF_ONESHOT, dev_name(dev), mmc);
 }
 
 static void of_mmc_spi_exit(struct device *dev, void *mmc)

drivers/mmc/host/omap_hsmmc.c

@@ -2250,9 +2250,7 @@ static int omap_hsmmc_remove(struct platform_device *pdev)
 	pm_runtime_get_sync(host->dev);
 	mmc_remove_host(host->mmc);
 
-	if (host->tx_chan)
 	dma_release_channel(host->tx_chan);
-	if (host->rx_chan)
 	dma_release_channel(host->rx_chan);
 
 	pm_runtime_put_sync(host->dev);

drivers/mmc/host/sdhci-esdhc-imx.c

@@ -76,6 +76,7 @@
 #define ESDHC_STD_TUNING_EN		(1 << 24)
 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
 #define ESDHC_TUNING_START_TAP		0x1
+#define ESDHC_TUNING_STEP_MASK		0x00070000
 #define ESDHC_TUNING_STEP_SHIFT		16
 
 /* pinctrl state */
@@ -489,8 +490,10 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 				m |= ESDHC_MIX_CTRL_FBCLK_SEL;
 				tuning_ctrl = readl(host->ioaddr + ESDHC_TUNING_CTRL);
 				tuning_ctrl |= ESDHC_STD_TUNING_EN | ESDHC_TUNING_START_TAP;
-				if (imx_data->boarddata.tuning_step)
+				if (imx_data->boarddata.tuning_step) {
+					tuning_ctrl &= ~ESDHC_TUNING_STEP_MASK;
 					tuning_ctrl |= imx_data->boarddata.tuning_step << ESDHC_TUNING_STEP_SHIFT;
+				}
 				writel(tuning_ctrl, host->ioaddr + ESDHC_TUNING_CTRL);
 			} else {
 				v &= ~ESDHC_MIX_CTRL_EXE_TUNE;

drivers/mmc/host/sdhci-of-at91.c

@@ -21,6 +21,8 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
 
 #include "sdhci-pltfm.h"
 
@@ -51,6 +53,60 @@ static const struct of_device_id sdhci_at91_dt_match[] = {
 	{}
 };
 
+#ifdef CONFIG_PM
+static int sdhci_at91_runtime_suspend(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_at91_priv *priv = pltfm_host->priv;
+	int ret;
+
+	ret = sdhci_runtime_suspend_host(host);
+
+	clk_disable_unprepare(priv->gck);
+	clk_disable_unprepare(priv->hclock);
+	clk_disable_unprepare(priv->mainck);
+
+	return ret;
+}
+
+static int sdhci_at91_runtime_resume(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_at91_priv *priv = pltfm_host->priv;
+	int ret;
+
+	ret = clk_prepare_enable(priv->mainck);
+	if (ret) {
+		dev_err(dev, "can't enable mainck\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(priv->hclock);
+	if (ret) {
+		dev_err(dev, "can't enable hclock\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(priv->gck);
+	if (ret) {
+		dev_err(dev, "can't enable gck\n");
+		return ret;
+	}
+
+	return sdhci_runtime_resume_host(host);
+}
+#endif /* CONFIG_PM */
+
+static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(sdhci_at91_runtime_suspend,
+			   sdhci_at91_runtime_resume,
+			   NULL)
+};
+
 static int sdhci_at91_probe(struct platform_device *pdev)
 {
 	const struct of_device_id	*match;
@@ -144,12 +200,23 @@ static int sdhci_at91_probe(struct platform_device *pdev)
 
 	sdhci_get_of_property(pdev);
 
+	pm_runtime_get_noresume(&pdev->dev);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
+	pm_runtime_use_autosuspend(&pdev->dev);
+
 	ret = sdhci_add_host(host);
 	if (ret)
-		goto clocks_disable_unprepare;
+		goto pm_runtime_disable;
+
+	pm_runtime_put_autosuspend(&pdev->dev);
 
 	return 0;
 
+pm_runtime_disable:
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
 clocks_disable_unprepare:
 	clk_disable_unprepare(priv->gck);
 	clk_disable_unprepare(priv->mainck);
@@ -165,6 +232,10 @@ static int sdhci_at91_remove(struct platform_device *pdev)
 	struct sdhci_pltfm_host	*pltfm_host = sdhci_priv(host);
 	struct sdhci_at91_priv	*priv = pltfm_host->priv;
 
+	pm_runtime_get_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+
 	sdhci_pltfm_unregister(pdev);
 
 	clk_disable_unprepare(priv->gck);
@@ -178,7 +249,7 @@ static struct platform_driver sdhci_at91_driver = {
 	.driver		= {
 		.name	= "sdhci-at91",
 		.of_match_table = sdhci_at91_dt_match,
-		.pm	= SDHCI_PLTFM_PMOPS,
+		.pm	= &sdhci_at91_dev_pm_ops,
 	},
 	.probe		= sdhci_at91_probe,
 	.remove		= sdhci_at91_remove,

drivers/mmc/host/sdhci-of-esdhc.c

@@ -584,6 +584,8 @@ static int sdhci_esdhc_probe(struct platform_device *pdev)
 {
 	struct sdhci_host *host;
 	struct device_node *np;
+	struct sdhci_pltfm_host *pltfm_host;
+	struct sdhci_esdhc *esdhc;
 	int ret;
 
 	np = pdev->dev.of_node;
@@ -600,6 +602,14 @@ static int sdhci_esdhc_probe(struct platform_device *pdev)
 
 	sdhci_get_of_property(pdev);
 
+	pltfm_host = sdhci_priv(host);
+	esdhc = pltfm_host->priv;
+	if (esdhc->vendor_ver == VENDOR_V_22)
+		host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;
+
+	if (esdhc->vendor_ver > VENDOR_V_22)
+		host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
+
 	if (of_device_is_compatible(np, "fsl,p5040-esdhc") ||
 	    of_device_is_compatible(np, "fsl,p5020-esdhc") ||
 	    of_device_is_compatible(np, "fsl,p4080-esdhc") ||

drivers/mmc/host/sdhci-pci-core.c

@@ -277,7 +277,7 @@ static int spt_select_drive_strength(struct sdhci_host *host,
 	if (sdhci_pci_spt_drive_strength > 0)
 		drive_strength = sdhci_pci_spt_drive_strength & 0xf;
 	else
-		drive_strength = 1; /* 33-ohm */
+		drive_strength = 0; /* Default 50-ohm */
 
 	if ((mmc_driver_type_mask(drive_strength) & card_drv) == 0)
 		drive_strength = 0; /* Default 50-ohm */
@@ -1464,7 +1464,7 @@ static int sdhci_pci_resume(struct device *dev)
 
 static int sdhci_pci_runtime_suspend(struct device *dev)
 {
-	struct pci_dev *pdev = container_of(dev, struct pci_dev, dev);
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct sdhci_pci_chip *chip;
 	struct sdhci_pci_slot *slot;
 	int i, ret;
@@ -1500,7 +1500,7 @@ static int sdhci_pci_runtime_suspend(struct device *dev)
 
 static int sdhci_pci_runtime_resume(struct device *dev)
 {
-	struct pci_dev *pdev = container_of(dev, struct pci_dev, dev);
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct sdhci_pci_chip *chip;
 	struct sdhci_pci_slot *slot;
 	int i, ret;

drivers/mmc/host/sdhci-pltfm.c

@@ -104,7 +104,8 @@ void sdhci_get_of_property(struct platform_device *pdev)
 	if (of_find_property(np, "keep-power-in-suspend", NULL))
 		host->mmc->pm_caps |= MMC_PM_KEEP_POWER;
 
-	if (of_find_property(np, "enable-sdio-wakeup", NULL))
+	if (of_property_read_bool(np, "wakeup-source") ||
+	    of_property_read_bool(np, "enable-sdio-wakeup")) /* legacy */
 		host->mmc->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
 }
 #else

drivers/mmc/host/sdhci-tegra.c

@@ -22,12 +22,20 @@
 #include <linux/of_device.h>
 #include <linux/mmc/card.h>
 #include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
 #include <linux/mmc/slot-gpio.h>
 #include <linux/gpio/consumer.h>
 
 #include "sdhci-pltfm.h"
 
 /* Tegra SDHOST controller vendor register definitions */
+#define SDHCI_TEGRA_VENDOR_CLOCK_CTRL			0x100
+#define SDHCI_CLOCK_CTRL_TAP_MASK			0x00ff0000
+#define SDHCI_CLOCK_CTRL_TAP_SHIFT			16
+#define SDHCI_CLOCK_CTRL_SDR50_TUNING_OVERRIDE		BIT(5)
+#define SDHCI_CLOCK_CTRL_PADPIPE_CLKEN_OVERRIDE		BIT(3)
+#define SDHCI_CLOCK_CTRL_SPI_MODE_CLKEN_OVERRIDE	BIT(2)
+
 #define SDHCI_TEGRA_VENDOR_MISC_CTRL		0x120
 #define SDHCI_MISC_CTRL_ENABLE_SDR104		0x8
 #define SDHCI_MISC_CTRL_ENABLE_SDR50		0x10
@@ -37,9 +45,9 @@
 #define NVQUIRK_FORCE_SDHCI_SPEC_200	BIT(0)
 #define NVQUIRK_ENABLE_BLOCK_GAP_DET	BIT(1)
 #define NVQUIRK_ENABLE_SDHCI_SPEC_300	BIT(2)
-#define NVQUIRK_DISABLE_SDR50		BIT(3)
-#define NVQUIRK_DISABLE_SDR104		BIT(4)
-#define NVQUIRK_DISABLE_DDR50		BIT(5)
+#define NVQUIRK_ENABLE_SDR50		BIT(3)
+#define NVQUIRK_ENABLE_SDR104		BIT(4)
+#define NVQUIRK_ENABLE_DDR50		BIT(5)
 
 struct sdhci_tegra_soc_data {
 	const struct sdhci_pltfm_data *pdata;
@@ -49,6 +57,7 @@ struct sdhci_tegra_soc_data {
 struct sdhci_tegra {
 	const struct sdhci_tegra_soc_data *soc_data;
 	struct gpio_desc *power_gpio;
+	bool ddr_signaling;
 };
 
 static u16 tegra_sdhci_readw(struct sdhci_host *host, int reg)
@@ -124,25 +133,33 @@ static void tegra_sdhci_reset(struct sdhci_host *host, u8 mask)
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_tegra *tegra_host = pltfm_host->priv;
 	const struct sdhci_tegra_soc_data *soc_data = tegra_host->soc_data;
-	u32 misc_ctrl;
+	u32 misc_ctrl, clk_ctrl;
 
 	sdhci_reset(host, mask);
 
 	if (!(mask & SDHCI_RESET_ALL))
 		return;
 
-	misc_ctrl = sdhci_readw(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);
+	misc_ctrl = sdhci_readl(host, SDHCI_TEGRA_VENDOR_MISC_CTRL);
 	/* Erratum: Enable SDHCI spec v3.00 support */
 	if (soc_data->nvquirks & NVQUIRK_ENABLE_SDHCI_SPEC_300)
 		misc_ctrl |= SDHCI_MISC_CTRL_ENABLE_SDHCI_SPEC_300;
-	/* Don't advertise UHS modes which aren't supported yet */
-	if (soc_data->nvquirks & NVQUIRK_DISABLE_SDR50)
-		misc_ctrl &= ~SDHCI_MISC_CTRL_ENABLE_SDR50;
-	if (soc_data->nvquirks & NVQUIRK_DISABLE_DDR50)
-		misc_ctrl &= ~SDHCI_MISC_CTRL_ENABLE_DDR50;
-	if (soc_data->nvquirks & NVQUIRK_DISABLE_SDR104)
-		misc_ctrl &= ~SDHCI_MISC_CTRL_ENABLE_SDR104;
-	sdhci_writew(host, misc_ctrl, SDHCI_TEGRA_VENDOR_MISC_CTRL);
+	/* Advertise UHS modes as supported by host */
+	if (soc_data->nvquirks & NVQUIRK_ENABLE_SDR50)
+		misc_ctrl |= SDHCI_MISC_CTRL_ENABLE_SDR50;
+	if (soc_data->nvquirks & NVQUIRK_ENABLE_DDR50)
+		misc_ctrl |= SDHCI_MISC_CTRL_ENABLE_DDR50;
+	if (soc_data->nvquirks & NVQUIRK_ENABLE_SDR104)
+		misc_ctrl |= SDHCI_MISC_CTRL_ENABLE_SDR104;
+	sdhci_writel(host, misc_ctrl, SDHCI_TEGRA_VENDOR_MISC_CTRL);
+
+	clk_ctrl = sdhci_readl(host, SDHCI_TEGRA_VENDOR_CLOCK_CTRL);
+	clk_ctrl &= ~SDHCI_CLOCK_CTRL_SPI_MODE_CLKEN_OVERRIDE;
+	if (soc_data->nvquirks & SDHCI_MISC_CTRL_ENABLE_SDR50)
+		clk_ctrl |= SDHCI_CLOCK_CTRL_SDR50_TUNING_OVERRIDE;
+	sdhci_writel(host, clk_ctrl, SDHCI_TEGRA_VENDOR_CLOCK_CTRL);
+
+	tegra_host->ddr_signaling = false;
 }
 
 static void tegra_sdhci_set_bus_width(struct sdhci_host *host, int bus_width)
@@ -164,15 +181,99 @@ static void tegra_sdhci_set_bus_width(struct sdhci_host *host, int bus_width)
 	sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 }
 
+static void tegra_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_tegra *tegra_host = pltfm_host->priv;
+	unsigned long host_clk;
+
+	if (!clock)
+		return;
+
+	host_clk = tegra_host->ddr_signaling ? clock * 2 : clock;
+	clk_set_rate(pltfm_host->clk, host_clk);
+	host->max_clk = clk_get_rate(pltfm_host->clk);
+
+	return sdhci_set_clock(host, clock);
+}
+
+static void tegra_sdhci_set_uhs_signaling(struct sdhci_host *host,
+					  unsigned timing)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_tegra *tegra_host = pltfm_host->priv;
+
+	if (timing == MMC_TIMING_UHS_DDR50)
+		tegra_host->ddr_signaling = true;
+
+	return sdhci_set_uhs_signaling(host, timing);
+}
+
+static unsigned int tegra_sdhci_get_max_clock(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+	/*
+	 * DDR modes require the host to run at double the card frequency, so
+	 * the maximum rate we can support is half of the module input clock.
+	 */
+	return clk_round_rate(pltfm_host->clk, UINT_MAX) / 2;
+}
+
+static void tegra_sdhci_set_tap(struct sdhci_host *host, unsigned int tap)
+{
+	u32 reg;
+
+	reg = sdhci_readl(host, SDHCI_TEGRA_VENDOR_CLOCK_CTRL);
+	reg &= ~SDHCI_CLOCK_CTRL_TAP_MASK;
+	reg |= tap << SDHCI_CLOCK_CTRL_TAP_SHIFT;
+	sdhci_writel(host, reg, SDHCI_TEGRA_VENDOR_CLOCK_CTRL);
+}
+
+static int tegra_sdhci_execute_tuning(struct sdhci_host *host, u32 opcode)
+{
+	unsigned int min, max;
+
+	/*
+	 * Start search for minimum tap value at 10, as smaller values are
+	 * may wrongly be reported as working but fail at higher speeds,
+	 * according to the TRM.
+	 */
+	min = 10;
+	while (min < 255) {
+		tegra_sdhci_set_tap(host, min);
+		if (!mmc_send_tuning(host->mmc, opcode, NULL))
+			break;
+		min++;
+	}
+
+	/* Find the maximum tap value that still passes. */
+	max = min + 1;
+	while (max < 255) {
+		tegra_sdhci_set_tap(host, max);
+		if (mmc_send_tuning(host->mmc, opcode, NULL)) {
+			max--;
+			break;
+		}
+		max++;
+	}
+
+	/* The TRM states the ideal tap value is at 75% in the passing range. */
+	tegra_sdhci_set_tap(host, min + ((max - min) * 3 / 4));
+
+	return mmc_send_tuning(host->mmc, opcode, NULL);
+}
+
 static const struct sdhci_ops tegra_sdhci_ops = {
 	.get_ro     = tegra_sdhci_get_ro,
 	.read_w     = tegra_sdhci_readw,
 	.write_l    = tegra_sdhci_writel,
-	.set_clock  = sdhci_set_clock,
+	.set_clock  = tegra_sdhci_set_clock,
 	.set_bus_width = tegra_sdhci_set_bus_width,
 	.reset      = tegra_sdhci_reset,
-	.set_uhs_signaling = sdhci_set_uhs_signaling,
-	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
+	.platform_execute_tuning = tegra_sdhci_execute_tuning,
+	.set_uhs_signaling = tegra_sdhci_set_uhs_signaling,
+	.get_max_clock = tegra_sdhci_get_max_clock,
 };
 
 static const struct sdhci_pltfm_data sdhci_tegra20_pdata = {
@@ -184,7 +285,7 @@ static const struct sdhci_pltfm_data sdhci_tegra20_pdata = {
 	.ops  = &tegra_sdhci_ops,
 };
 
-static struct sdhci_tegra_soc_data soc_data_tegra20 = {
+static const struct sdhci_tegra_soc_data soc_data_tegra20 = {
 	.pdata = &sdhci_tegra20_pdata,
 	.nvquirks = NVQUIRK_FORCE_SDHCI_SPEC_200 |
 		    NVQUIRK_ENABLE_BLOCK_GAP_DET,
@@ -197,14 +298,15 @@ static const struct sdhci_pltfm_data sdhci_tegra30_pdata = {
 		  SDHCI_QUIRK_NO_HISPD_BIT |
 		  SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC |
 		  SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
 	.ops  = &tegra_sdhci_ops,
 };
 
-static struct sdhci_tegra_soc_data soc_data_tegra30 = {
+static const struct sdhci_tegra_soc_data soc_data_tegra30 = {
 	.pdata = &sdhci_tegra30_pdata,
 	.nvquirks = NVQUIRK_ENABLE_SDHCI_SPEC_300 |
-		    NVQUIRK_DISABLE_SDR50 |
-		    NVQUIRK_DISABLE_SDR104,
+		    NVQUIRK_ENABLE_SDR50 |
+		    NVQUIRK_ENABLE_SDR104,
 };
 
 static const struct sdhci_ops tegra114_sdhci_ops = {
@@ -212,11 +314,12 @@ static const struct sdhci_ops tegra114_sdhci_ops = {
 	.read_w     = tegra_sdhci_readw,
 	.write_w    = tegra_sdhci_writew,
 	.write_l    = tegra_sdhci_writel,
-	.set_clock  = sdhci_set_clock,
+	.set_clock  = tegra_sdhci_set_clock,
 	.set_bus_width = tegra_sdhci_set_bus_width,
 	.reset      = tegra_sdhci_reset,
-	.set_uhs_signaling = sdhci_set_uhs_signaling,
-	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
+	.platform_execute_tuning = tegra_sdhci_execute_tuning,
+	.set_uhs_signaling = tegra_sdhci_set_uhs_signaling,
+	.get_max_clock = tegra_sdhci_get_max_clock,
 };
 
 static const struct sdhci_pltfm_data sdhci_tegra114_pdata = {
@@ -226,17 +329,34 @@ static const struct sdhci_pltfm_data sdhci_tegra114_pdata = {
 		  SDHCI_QUIRK_NO_HISPD_BIT |
 		  SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC |
 		  SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
 	.ops  = &tegra114_sdhci_ops,
 };
 
-static struct sdhci_tegra_soc_data soc_data_tegra114 = {
+static const struct sdhci_tegra_soc_data soc_data_tegra114 = {
 	.pdata = &sdhci_tegra114_pdata,
-	.nvquirks = NVQUIRK_DISABLE_SDR50 |
-		    NVQUIRK_DISABLE_DDR50 |
-		    NVQUIRK_DISABLE_SDR104,
+	.nvquirks = NVQUIRK_ENABLE_SDR50 |
+		    NVQUIRK_ENABLE_DDR50 |
+		    NVQUIRK_ENABLE_SDR104,
+};
+
+static const struct sdhci_pltfm_data sdhci_tegra210_pdata = {
+	.quirks = SDHCI_QUIRK_BROKEN_TIMEOUT_VAL |
+		  SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
+		  SDHCI_QUIRK_SINGLE_POWER_WRITE |
+		  SDHCI_QUIRK_NO_HISPD_BIT |
+		  SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC |
+		  SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+	.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
+	.ops  = &tegra114_sdhci_ops,
+};
+
+static const struct sdhci_tegra_soc_data soc_data_tegra210 = {
+	.pdata = &sdhci_tegra210_pdata,
 };
 
 static const struct of_device_id sdhci_tegra_dt_match[] = {
+	{ .compatible = "nvidia,tegra210-sdhci", .data = &soc_data_tegra210 },
 	{ .compatible = "nvidia,tegra124-sdhci", .data = &soc_data_tegra114 },
 	{ .compatible = "nvidia,tegra114-sdhci", .data = &soc_data_tegra114 },
 	{ .compatible = "nvidia,tegra30-sdhci", .data = &soc_data_tegra30 },
@@ -271,6 +391,7 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
 		rc = -ENOMEM;
 		goto err_alloc_tegra_host;
 	}
+	tegra_host->ddr_signaling = false;
 	tegra_host->soc_data = soc_data;
 	pltfm_host->priv = tegra_host;
 
@@ -278,6 +399,9 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
 	if (rc)
 		goto err_parse_dt;
 
+	if (tegra_host->soc_data->nvquirks & NVQUIRK_ENABLE_DDR50)
+		host->mmc->caps |= MMC_CAP_1_8V_DDR;
+
 	tegra_host->power_gpio = devm_gpiod_get_optional(&pdev->dev, "power",
 							 GPIOD_OUT_HIGH);
 	if (IS_ERR(tegra_host->power_gpio)) {

drivers/mmc/host/sdhci.c

@@ -492,7 +492,7 @@ static int sdhci_adma_table_pre(struct sdhci_host *host,
 		host->align_buffer, host->align_buffer_sz, direction);
 	if (dma_mapping_error(mmc_dev(host->mmc), host->align_addr))
 		goto fail;
-	BUG_ON(host->align_addr & host->align_mask);
+	BUG_ON(host->align_addr & SDHCI_ADMA2_MASK);
 
 	host->sg_count = sdhci_pre_dma_transfer(host, data);
 	if (host->sg_count < 0)
@@ -514,8 +514,8 @@ static int sdhci_adma_table_pre(struct sdhci_host *host,
 		 * the (up to three) bytes that screw up the
 		 * alignment.
 		 */
-		offset = (host->align_sz - (addr & host->align_mask)) &
-			 host->align_mask;
+		offset = (SDHCI_ADMA2_ALIGN - (addr & SDHCI_ADMA2_MASK)) &
+			 SDHCI_ADMA2_MASK;
 		if (offset) {
 			if (data->flags & MMC_DATA_WRITE) {
 				buffer = sdhci_kmap_atomic(sg, &flags);
@@ -529,8 +529,8 @@ static int sdhci_adma_table_pre(struct sdhci_host *host,
 
 			BUG_ON(offset > 65536);
 
-			align += host->align_sz;
-			align_addr += host->align_sz;
+			align += SDHCI_ADMA2_ALIGN;
+			align_addr += SDHCI_ADMA2_ALIGN;
 
 			desc += host->desc_sz;
 
@@ -540,9 +540,12 @@ static int sdhci_adma_table_pre(struct sdhci_host *host,
 
 		BUG_ON(len > 65536);
 
+		if (len) {
 			/* tran, valid */
-		sdhci_adma_write_desc(host, desc, addr, len, ADMA2_TRAN_VALID);
+			sdhci_adma_write_desc(host, desc, addr, len,
+					      ADMA2_TRAN_VALID);
 			desc += host->desc_sz;
+		}
 
 		/*
 		 * If this triggers then we have a calculation bug
@@ -608,7 +611,7 @@ static void sdhci_adma_table_post(struct sdhci_host *host,
 	/* Do a quick scan of the SG list for any unaligned mappings */
 	has_unaligned = false;
 	for_each_sg(data->sg, sg, host->sg_count, i)
-		if (sg_dma_address(sg) & host->align_mask) {
+		if (sg_dma_address(sg) & SDHCI_ADMA2_MASK) {
 			has_unaligned = true;
 			break;
 		}
@@ -620,15 +623,15 @@ static void sdhci_adma_table_post(struct sdhci_host *host,
 		align = host->align_buffer;
 
 		for_each_sg(data->sg, sg, host->sg_count, i) {
-			if (sg_dma_address(sg) & host->align_mask) {
-				size = host->align_sz -
-				       (sg_dma_address(sg) & host->align_mask);
+			if (sg_dma_address(sg) & SDHCI_ADMA2_MASK) {
+				size = SDHCI_ADMA2_ALIGN -
+				       (sg_dma_address(sg) & SDHCI_ADMA2_MASK);
 
 				buffer = sdhci_kmap_atomic(sg, &flags);
 				memcpy(buffer, align, size);
 				sdhci_kunmap_atomic(buffer, &flags);
 
-				align += host->align_sz;
+				align += SDHCI_ADMA2_ALIGN;
 			}
 		}
 	}
@@ -768,8 +771,7 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
 		if (unlikely(broken)) {
 			for_each_sg(data->sg, sg, data->sg_len, i) {
 				if (sg->length & 0x3) {
-					DBG("Reverting to PIO because of "
-						"transfer size (%d)\n",
+					DBG("Reverting to PIO because of transfer size (%d)\n",
 						sg->length);
 					host->flags &= ~SDHCI_REQ_USE_DMA;
 					break;
@@ -803,8 +805,7 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
 		if (unlikely(broken)) {
 			for_each_sg(data->sg, sg, data->sg_len, i) {
 				if (sg->offset & 0x3) {
-					DBG("Reverting to PIO because of "
-						"bad alignment\n");
+					DBG("Reverting to PIO because of bad alignment\n");
 					host->flags &= ~SDHCI_REQ_USE_DMA;
 					break;
 				}
@@ -1016,8 +1017,8 @@ void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
 
 	while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
 		if (timeout == 0) {
-			pr_err("%s: Controller never released "
-				"inhibit bit(s).\n", mmc_hostname(host->mmc));
+			pr_err("%s: Controller never released inhibit bit(s).\n",
+			       mmc_hostname(host->mmc));
 			sdhci_dumpregs(host);
 			cmd->error = -EIO;
 			tasklet_schedule(&host->finish_tasklet);
@@ -1254,8 +1255,8 @@ void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
 	while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
 		& SDHCI_CLOCK_INT_STABLE)) {
 		if (timeout == 0) {
-			pr_err("%s: Internal clock never "
-				"stabilised.\n", mmc_hostname(host->mmc));
+			pr_err("%s: Internal clock never stabilised.\n",
+			       mmc_hostname(host->mmc));
 			sdhci_dumpregs(host);
 			return;
 		}
@@ -1274,19 +1275,6 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
 	struct mmc_host *mmc = host->mmc;
 	u8 pwr = 0;
 
-	if (!IS_ERR(mmc->supply.vmmc)) {
-		spin_unlock_irq(&host->lock);
-		mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
-		spin_lock_irq(&host->lock);
-
-		if (mode != MMC_POWER_OFF)
-			sdhci_writeb(host, SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
-		else
-			sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
-
-		return;
-	}
-
 	if (mode != MMC_POWER_OFF) {
 		switch (1 << vdd) {
 		case MMC_VDD_165_195:
@@ -1301,7 +1289,9 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
 			pwr = SDHCI_POWER_330;
 			break;
 		default:
-			BUG();
+			WARN(1, "%s: Invalid vdd %#x\n",
+			     mmc_hostname(host->mmc), vdd);
+			break;
 		}
 	}
 
@@ -1345,6 +1335,12 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
 		if (host->quirks & SDHCI_QUIRK_DELAY_AFTER_POWER)
 			mdelay(10);
 	}
+
+	if (!IS_ERR(mmc->supply.vmmc)) {
+		spin_unlock_irq(&host->lock);
+		mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
+		spin_lock_irq(&host->lock);
+	}
 }
 
 /*****************************************************************************\
@@ -1540,8 +1536,8 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
 			else if (ios->drv_type == MMC_SET_DRIVER_TYPE_D)
 				ctrl_2 |= SDHCI_CTRL_DRV_TYPE_D;
 			else {
-				pr_warn("%s: invalid driver type, default to "
-					"driver type B\n", mmc_hostname(mmc));
+				pr_warn("%s: invalid driver type, default to driver type B\n",
+					mmc_hostname(mmc));
 				ctrl_2 |= SDHCI_CTRL_DRV_TYPE_B;
 			}
 
@@ -2015,10 +2011,7 @@ static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
 		spin_lock_irqsave(&host->lock, flags);
 
 		if (!host->tuning_done) {
-			pr_info(DRIVER_NAME ": Timeout waiting for "
-				"Buffer Read Ready interrupt during tuning "
-				"procedure, falling back to fixed sampling "
-				"clock\n");
+			pr_info(DRIVER_NAME ": Timeout waiting for Buffer Read Ready interrupt during tuning procedure, falling back to fixed sampling clock\n");
 			ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 			ctrl &= ~SDHCI_CTRL_TUNED_CLK;
 			ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
@@ -2046,9 +2039,7 @@ static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
 		sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
 	}
 	if (!(ctrl & SDHCI_CTRL_TUNED_CLK)) {
-		pr_info(DRIVER_NAME ": Tuning procedure"
-			" failed, falling back to fixed sampling"
-			" clock\n");
+		pr_info(DRIVER_NAME ": Tuning procedure failed, falling back to fixed sampling clock\n");
 		err = -EIO;
 	}
 
@@ -2293,8 +2284,8 @@ static void sdhci_timeout_timer(unsigned long data)
 	spin_lock_irqsave(&host->lock, flags);
 
 	if (host->mrq) {
-		pr_err("%s: Timeout waiting for hardware "
-			"interrupt.\n", mmc_hostname(host->mmc));
+		pr_err("%s: Timeout waiting for hardware interrupt.\n",
+		       mmc_hostname(host->mmc));
 		sdhci_dumpregs(host);
 
 		if (host->data) {
@@ -2325,8 +2316,7 @@ static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *mask)
 	BUG_ON(intmask == 0);
 
 	if (!host->cmd) {
-		pr_err("%s: Got command interrupt 0x%08x even "
-			"though no command operation was in progress.\n",
+		pr_err("%s: Got command interrupt 0x%08x even though no command operation was in progress.\n",
 		       mmc_hostname(host->mmc), (unsigned)intmask);
 		sdhci_dumpregs(host);
 		return;
@@ -2356,8 +2346,7 @@ static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *mask)
 	 */
 	if (host->cmd->flags & MMC_RSP_BUSY) {
 		if (host->cmd->data)
-			DBG("Cannot wait for busy signal when also "
-				"doing a data transfer");
+			DBG("Cannot wait for busy signal when also doing a data transfer");
 		else if (!(host->quirks & SDHCI_QUIRK_NO_BUSY_IRQ)
 				&& !host->busy_handle) {
 			/* Mark that command complete before busy is ended */
@@ -2451,8 +2440,7 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
 			}
 		}
 
-		pr_err("%s: Got data interrupt 0x%08x even "
-			"though no data operation was in progress.\n",
+		pr_err("%s: Got data interrupt 0x%08x even though no data operation was in progress.\n",
 		       mmc_hostname(host->mmc), (unsigned)intmask);
 		sdhci_dumpregs(host);
 
@@ -2760,7 +2748,7 @@ static int sdhci_runtime_pm_put(struct sdhci_host *host)
 
 static void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
 {
-	if (host->runtime_suspended || host->bus_on)
+	if (host->bus_on)
 		return;
 	host->bus_on = true;
 	pm_runtime_get_noresume(host->mmc->parent);
@@ -2768,7 +2756,7 @@ static void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
 
 static void sdhci_runtime_pm_bus_off(struct sdhci_host *host)
 {
-	if (host->runtime_suspended || !host->bus_on)
+	if (!host->bus_on)
 		return;
 	host->bus_on = false;
 	pm_runtime_put_noidle(host->mmc->parent);
@@ -2896,9 +2884,8 @@ int sdhci_add_host(struct sdhci_host *host)
 	host->version = (host->version & SDHCI_SPEC_VER_MASK)
 				>> SDHCI_SPEC_VER_SHIFT;
 	if (host->version > SDHCI_SPEC_300) {
-		pr_err("%s: Unknown controller version (%d). "
-			"You may experience problems.\n", mmc_hostname(mmc),
-			host->version);
+		pr_err("%s: Unknown controller version (%d). You may experience problems.\n",
+		       mmc_hostname(mmc), host->version);
 	}
 
 	caps[0] = (host->quirks & SDHCI_QUIRK_MISSING_CAPS) ? host->caps :
@@ -2967,24 +2954,17 @@ int sdhci_add_host(struct sdhci_host *host)
 		if (host->flags & SDHCI_USE_64_BIT_DMA) {
 			host->adma_table_sz = (SDHCI_MAX_SEGS * 2 + 1) *
 					      SDHCI_ADMA2_64_DESC_SZ;
-			host->align_buffer_sz = SDHCI_MAX_SEGS *
-						SDHCI_ADMA2_64_ALIGN;
 			host->desc_sz = SDHCI_ADMA2_64_DESC_SZ;
-			host->align_sz = SDHCI_ADMA2_64_ALIGN;
-			host->align_mask = SDHCI_ADMA2_64_ALIGN - 1;
 		} else {
 			host->adma_table_sz = (SDHCI_MAX_SEGS * 2 + 1) *
 					      SDHCI_ADMA2_32_DESC_SZ;
-			host->align_buffer_sz = SDHCI_MAX_SEGS *
-						SDHCI_ADMA2_32_ALIGN;
 			host->desc_sz = SDHCI_ADMA2_32_DESC_SZ;
-			host->align_sz = SDHCI_ADMA2_32_ALIGN;
-			host->align_mask = SDHCI_ADMA2_32_ALIGN - 1;
 		}
 		host->adma_table = dma_alloc_coherent(mmc_dev(mmc),
 						      host->adma_table_sz,
 						      &host->adma_addr,
 						      GFP_KERNEL);
+		host->align_buffer_sz = SDHCI_MAX_SEGS * SDHCI_ADMA2_ALIGN;
 		host->align_buffer = kmalloc(host->align_buffer_sz, GFP_KERNEL);
 		if (!host->adma_table || !host->align_buffer) {
 			if (host->adma_table)
@@ -2998,7 +2978,7 @@ int sdhci_add_host(struct sdhci_host *host)
 			host->flags &= ~SDHCI_USE_ADMA;
 			host->adma_table = NULL;
 			host->align_buffer = NULL;
-		} else if (host->adma_addr & host->align_mask) {
+		} else if (host->adma_addr & (SDHCI_ADMA2_DESC_ALIGN - 1)) {
 			pr_warn("%s: unable to allocate aligned ADMA descriptor\n",
 				mmc_hostname(mmc));
 			host->flags &= ~SDHCI_USE_ADMA;
@@ -3031,8 +3011,8 @@ int sdhci_add_host(struct sdhci_host *host)
 	if (host->max_clk == 0 || host->quirks &
 			SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN) {
 		if (!host->ops->get_max_clock) {
-			pr_err("%s: Hardware doesn't specify base clock "
-			       "frequency.\n", mmc_hostname(mmc));
+			pr_err("%s: Hardware doesn't specify base clock frequency.\n",
+			       mmc_hostname(mmc));
 			return -ENODEV;
 		}
 		host->max_clk = host->ops->get_max_clock(host);
@@ -3294,8 +3274,8 @@ int sdhci_add_host(struct sdhci_host *host)
 		mmc->ocr_avail_mmc &= host->ocr_avail_mmc;
 
 	if (mmc->ocr_avail == 0) {
-		pr_err("%s: Hardware doesn't report any "
-			"support voltages.\n", mmc_hostname(mmc));
+		pr_err("%s: Hardware doesn't report any support voltages.\n",
+		       mmc_hostname(mmc));
 		return -ENODEV;
 	}
 

drivers/mmc/host/sdhci.h

@@ -272,22 +272,27 @@
 /* ADMA2 32-bit DMA descriptor size */
 #define SDHCI_ADMA2_32_DESC_SZ	8
 
-/* ADMA2 32-bit DMA alignment */
-#define SDHCI_ADMA2_32_ALIGN	4
-
 /* ADMA2 32-bit descriptor */
 struct sdhci_adma2_32_desc {
 	__le16	cmd;
 	__le16	len;
 	__le32	addr;
-}  __packed __aligned(SDHCI_ADMA2_32_ALIGN);
+}  __packed __aligned(4);
+
+/* ADMA2 data alignment */
+#define SDHCI_ADMA2_ALIGN	4
+#define SDHCI_ADMA2_MASK	(SDHCI_ADMA2_ALIGN - 1)
+
+/*
+ * ADMA2 descriptor alignment.  Some controllers (e.g. Intel) require 8 byte
+ * alignment for the descriptor table even in 32-bit DMA mode.  Memory
+ * allocation is at least 8 byte aligned anyway, so just stipulate 8 always.
+ */
+#define SDHCI_ADMA2_DESC_ALIGN	8
 
 /* ADMA2 64-bit DMA descriptor size */
 #define SDHCI_ADMA2_64_DESC_SZ	12
 
-/* ADMA2 64-bit DMA alignment */
-#define SDHCI_ADMA2_64_ALIGN	8
-
 /*
  * ADMA2 64-bit descriptor. Note 12-byte descriptor can't always be 8-byte
  * aligned.
@@ -482,8 +487,6 @@ struct sdhci_host {
 	dma_addr_t align_addr;	/* Mapped bounce buffer */
 
 	unsigned int desc_sz;	/* ADMA descriptor size */
-	unsigned int align_sz;	/* ADMA alignment */
-	unsigned int align_mask;	/* ADMA alignment mask */
 
 	struct tasklet_struct finish_tasklet;	/* Tasklet structures */
 

drivers/mmc/host/sh_mmcif.c

@@ -397,38 +397,26 @@ static void sh_mmcif_start_dma_tx(struct sh_mmcif_host *host)
 }
 
 static struct dma_chan *
-sh_mmcif_request_dma_one(struct sh_mmcif_host *host,
-			 struct sh_mmcif_plat_data *pdata,
-			 enum dma_transfer_direction direction)
+sh_mmcif_request_dma_pdata(struct sh_mmcif_host *host, uintptr_t slave_id)
 {
-	struct dma_slave_config cfg = { 0, };
-	struct dma_chan *chan;
-	void *slave_data = NULL;
-	struct resource *res;
-	struct device *dev = sh_mmcif_host_to_dev(host);
 	dma_cap_mask_t mask;
-	int ret;
 
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_SLAVE, mask);
+	if (slave_id <= 0)
+		return NULL;
 
-	if (pdata)
-		slave_data = direction == DMA_MEM_TO_DEV ?
-			(void *)pdata->slave_id_tx :
-			(void *)pdata->slave_id_rx;
-
-	chan = dma_request_slave_channel_compat(mask, shdma_chan_filter,
-				slave_data, dev,
-				direction == DMA_MEM_TO_DEV ? "tx" : "rx");
-
-	dev_dbg(dev, "%s: %s: got channel %p\n", __func__,
-		direction == DMA_MEM_TO_DEV ? "TX" : "RX", chan);
+	return dma_request_channel(mask, shdma_chan_filter, (void *)slave_id);
+}
 
-	if (!chan)
-		return NULL;
+static int sh_mmcif_dma_slave_config(struct sh_mmcif_host *host,
+				     struct dma_chan *chan,
+				     enum dma_transfer_direction direction)
+{
+	struct resource *res;
+	struct dma_slave_config cfg = { 0, };
 
 	res = platform_get_resource(host->pd, IORESOURCE_MEM, 0);
-
 	cfg.direction = direction;
 
 	if (direction == DMA_DEV_TO_MEM) {
@@ -439,38 +427,42 @@ sh_mmcif_request_dma_one(struct sh_mmcif_host *host,
 		cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
 	}
 
-	ret = dmaengine_slave_config(chan, &cfg);
-	if (ret < 0) {
-		dma_release_channel(chan);
-		return NULL;
-	}
-
-	return chan;
+	return dmaengine_slave_config(chan, &cfg);
 }
 
-static void sh_mmcif_request_dma(struct sh_mmcif_host *host,
-				 struct sh_mmcif_plat_data *pdata)
+static void sh_mmcif_request_dma(struct sh_mmcif_host *host)
 {
 	struct device *dev = sh_mmcif_host_to_dev(host);
 	host->dma_active = false;
 
-	if (pdata) {
-		if (pdata->slave_id_tx <= 0 || pdata->slave_id_rx <= 0)
-			return;
-	} else if (!dev->of_node) {
-		return;
+	/* We can only either use DMA for both Tx and Rx or not use it at all */
+	if (IS_ENABLED(CONFIG_SUPERH) && dev->platform_data) {
+		struct sh_mmcif_plat_data *pdata = dev->platform_data;
+
+		host->chan_tx = sh_mmcif_request_dma_pdata(host,
+							pdata->slave_id_tx);
+		host->chan_rx = sh_mmcif_request_dma_pdata(host,
+							pdata->slave_id_rx);
+	} else {
+		host->chan_tx = dma_request_slave_channel(dev, "tx");
+		host->chan_tx = dma_request_slave_channel(dev, "rx");
 	}
+	dev_dbg(dev, "%s: got channel TX %p RX %p\n", __func__, host->chan_tx,
+		host->chan_rx);
+
+	if (!host->chan_tx || !host->chan_rx ||
+	    sh_mmcif_dma_slave_config(host, host->chan_tx, DMA_MEM_TO_DEV) ||
+	    sh_mmcif_dma_slave_config(host, host->chan_rx, DMA_DEV_TO_MEM))
+		goto error;
 
-	/* We can only either use DMA for both Tx and Rx or not use it at all */
-	host->chan_tx = sh_mmcif_request_dma_one(host, pdata, DMA_MEM_TO_DEV);
-	if (!host->chan_tx)
 	return;
 
-	host->chan_rx = sh_mmcif_request_dma_one(host, pdata, DMA_DEV_TO_MEM);
-	if (!host->chan_rx) {
+error:
+	if (host->chan_tx)
 		dma_release_channel(host->chan_tx);
-		host->chan_tx = NULL;
-	}
+	if (host->chan_rx)
+		dma_release_channel(host->chan_rx);
+	host->chan_tx = host->chan_rx = NULL;
 }
 
 static void sh_mmcif_release_dma(struct sh_mmcif_host *host)
@@ -1102,7 +1094,7 @@ static void sh_mmcif_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	if (ios->power_mode == MMC_POWER_UP) {
 		if (!host->card_present) {
 			/* See if we also get DMA */
-			sh_mmcif_request_dma(host, dev->platform_data);
+			sh_mmcif_request_dma(host);
 			host->card_present = true;
 		}
 		sh_mmcif_set_power(host, ios);

drivers/mmc/host/usdhi6rol0.c

@@ -1634,7 +1634,7 @@ static void usdhi6_timeout_work(struct work_struct *work)
 	struct usdhi6_host *host = container_of(d, struct usdhi6_host, timeout_work);
 	struct mmc_request *mrq = host->mrq;
 	struct mmc_data *data = mrq ? mrq->data : NULL;
-	struct scatterlist *sg = host->sg ?: data->sg;
+	struct scatterlist *sg;
 
 	dev_warn(mmc_dev(host->mmc),
 		 "%s timeout wait %u CMD%d: IRQ 0x%08x:0x%08x, last IRQ 0x%08x\n",
@@ -1666,6 +1666,7 @@ static void usdhi6_timeout_work(struct work_struct *work)
 	case USDHI6_WAIT_FOR_MWRITE:
 	case USDHI6_WAIT_FOR_READ:
 	case USDHI6_WAIT_FOR_WRITE:
+		sg = host->sg ?: data->sg;
 		dev_dbg(mmc_dev(host->mmc),
 			"%c: page #%u @ +0x%zx %ux%u in SG%u. Current SG %u bytes @ %u\n",
 			data->flags & MMC_DATA_READ ? 'R' : 'W', host->page_idx,

include/linux/mmc/dw_mmc.h

@@ -172,7 +172,7 @@ struct dw_mci {
 	/* For edmac */
 	struct dw_mci_dma_slave *dms;
 	/* Registers's physical base address */
-	void                    *phy_regs;
+	resource_size_t		phy_regs;
 
 	u32			cmd_status;
 	u32			data_status;
@@ -235,16 +235,10 @@ struct dw_mci_dma_ops {
 };
 
 /* IP Quirks/flags. */
-/* DTO fix for command transmission with IDMAC configured */
-#define DW_MCI_QUIRK_IDMAC_DTO			BIT(0)
-/* delay needed between retries on some 2.11a implementations */
-#define DW_MCI_QUIRK_RETRY_DELAY		BIT(1)
-/* High Speed Capable - Supports HS cards (up to 50MHz) */
-#define DW_MCI_QUIRK_HIGHSPEED			BIT(2)
 /* Unreliable card detection */
-#define DW_MCI_QUIRK_BROKEN_CARD_DETECTION	BIT(3)
+#define DW_MCI_QUIRK_BROKEN_CARD_DETECTION	BIT(0)
 /* Timer for broken data transfer over scheme */
-#define DW_MCI_QUIRK_BROKEN_DTO			BIT(4)
+#define DW_MCI_QUIRK_BROKEN_DTO			BIT(1)
 
 struct dma_pdata;
 

include/linux/mmc/host.h

@@ -212,7 +212,9 @@ struct mmc_host {
 	u32			ocr_avail_sdio;	/* SDIO-specific OCR */
 	u32			ocr_avail_sd;	/* SD-specific OCR */
 	u32			ocr_avail_mmc;	/* MMC-specific OCR */
+#ifdef CONFIG_PM_SLEEP
 	struct notifier_block	pm_notify;
+#endif
 	u32			max_current_330;
 	u32			max_current_300;
 	u32			max_current_180;
@@ -259,7 +261,6 @@ struct mmc_host {
 #define MMC_CAP_UHS_SDR50	(1 << 17)	/* Host supports UHS SDR50 mode */
 #define MMC_CAP_UHS_SDR104	(1 << 18)	/* Host supports UHS SDR104 mode */
 #define MMC_CAP_UHS_DDR50	(1 << 19)	/* Host supports UHS DDR50 mode */
-#define MMC_CAP_RUNTIME_RESUME	(1 << 20)	/* Resume at runtime_resume. */
 #define MMC_CAP_DRIVER_TYPE_A	(1 << 23)	/* Host supports Driver Type A */
 #define MMC_CAP_DRIVER_TYPE_C	(1 << 24)	/* Host supports Driver Type C */
 #define MMC_CAP_DRIVER_TYPE_D	(1 << 25)	/* Host supports Driver Type D */
@@ -289,6 +290,7 @@ struct mmc_host {
 #define MMC_CAP2_HSX00_1_2V	(MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V)
 #define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
 #define MMC_CAP2_NO_WRITE_PROTECT (1 << 18)	/* No physical write protect pin, assume that card is always read-write */
+#define MMC_CAP2_NO_SDIO	(1 << 19)	/* Do not send SDIO commands during initialization */
 
 	mmc_pm_flag_t		pm_caps;	/* supported pm features */
 
@@ -434,8 +436,6 @@ static inline int mmc_regulator_set_vqmmc(struct mmc_host *mmc,
 
 int mmc_regulator_get_supply(struct mmc_host *mmc);
 
-int mmc_pm_notify(struct notifier_block *notify_block, unsigned long, void *);
-
 static inline int mmc_card_is_removable(struct mmc_host *host)
 {
 	return !(host->caps & MMC_CAP_NONREMOVABLE);

include/linux/platform_data/mmc-mvsdio.h

-/*
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MMC_MVSDIO_H
-#define __MMC_MVSDIO_H
-
-#include <linux/mbus.h>
-
-struct mvsdio_platform_data {
-	unsigned int clock;
-	int gpio_card_detect;
-	int gpio_write_protect;
-};
-
-#endif

lib/Kconfig.debug

@@ -1534,8 +1534,7 @@ config FAIL_IO_TIMEOUT
 
 config FAIL_MMC_REQUEST
 	bool "Fault-injection capability for MMC IO"
-	select DEBUG_FS
-	depends on FAULT_INJECTION && MMC
+	depends on FAULT_INJECTION_DEBUG_FS && MMC
 	help
 	  Provide fault-injection capability for MMC IO.
 	  This will make the mmc core return data errors. This is