Merge branch 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6

arch/avr32/boards/atngw100/Kconfig

@@ -2,8 +2,15 @@
 
 if BOARD_ATNGW100
 
+choice
+	prompt "Select an NGW100 add-on board to support"
+	default BOARD_ATNGW100_ADDON_NONE
+
+config BOARD_ATNGW100_ADDON_NONE
+	bool "None"
+
 config BOARD_ATNGW100_EVKLCD10X
-	bool "Add support for EVKLCD10X addon board"
+	bool "EVKLCD10X addon board"
 	help
 	  This enables support for the EVKLCD100 (QVGA) or EVKLCD101 (VGA)
 	  addon board for the NGW100. By enabling this the LCD controller and
@@ -14,7 +21,19 @@ config BOARD_ATNGW100_EVKLCD10X
 	  The MCI pins can be reenabled by editing the "add device function" but
 	  this may break the setup for other displays that use these pins.
 
-	  Choose 'Y' here if you have a EVKLCD100/101 connected to the NGW100.
+config BOARD_ATNGW100_MRMT
+	bool "Mediama RMT1/2 add-on board"
+	help
+	  This enables support for the Mediama RMT1 or RMT2 board.
+	  RMT provides LCD support, AC97 codec and other
+	  optional peripherals to the Atmel NGW100.
+
+	  This choice disables the detect pin and the write-protect pin for the
+	  MCI platform device, since it conflicts with the LCD platform device.
+	  The MCI pins can be reenabled by editing the "add device function" but
+	  this may break the setup for other displays that use these pins.
+
+endchoice
 
 choice
 	prompt "LCD panel resolution on EVKLCD10X"
@@ -32,4 +51,8 @@ config BOARD_ATNGW100_EVKLCD10X_POW_QVGA
 
 endchoice
 
+if BOARD_ATNGW100_MRMT
+source	"arch/avr32/boards/atngw100/Kconfig_mrmt"
+endif
+
 endif	# BOARD_ATNGW100

arch/avr32/boards/atngw100/Kconfig_mrmt

+# RMT for NGW100 customization
+
+choice
+	prompt "RMT Version"
+	help
+	  Select the RMTx board version.
+
+config BOARD_MRMT_REV1
+	bool "RMT1"
+config BOARD_MRMT_REV2
+	bool "RMT2"
+
+endchoice
+
+config BOARD_MRMT_AC97
+	bool "Enable AC97 CODEC"
+	help
+	  Enable the UCB1400 AC97 CODEC driver.
+
+choice
+	prompt "Touchscreen Driver"
+	default BOARD_MRMT_ADS7846_TS
+
+config BOARD_MRMT_UCB1400_TS
+	bool "Use UCB1400 Touchscreen"
+
+config BOARD_MRMT_ADS7846_TS
+	bool "Use ADS7846 Touchscreen"
+
+endchoice
+
+choice
+	prompt "RMTx LCD Selection"
+	default BOARD_MRMT_LCD_DISABLE
+
+config BOARD_MRMT_LCD_DISABLE
+	bool "LCD Disabled"
+
+config BOARD_MRMT_LCD_LQ043T3DX0X
+	bool "Sharp LQ043T3DX0x or compatible"
+	help
+	  If using RMT2, be sure to load the resistor pack selectors accordingly
+
+if BOARD_MRMT_REV2
+config BOARD_MRMT_LCD_KWH043GM08
+	bool "Formike KWH043GM08 or compatible"
+	help
+	  Be sure to load the RMT2 resistor pack selectors accordingly
+endif
+
+endchoice
+
+if !BOARD_MRMT_LCD_DISABLE
+config BOARD_MRMT_BL_PWM
+	bool "Use PWM control for LCD Backlight"
+	help
+		Use PWM driver for controlling LCD Backlight.
+		Otherwise, LCD Backlight is always on.
+endif
+
+config BOARD_MRMT_RTC_I2C
+	bool "Use External RTC on I2C Bus"
+	help
+		RMT1 has an optional RTC device on the I2C bus.
+		It is a SII S35390A.  Be sure to select the
+		matching RTC driver.
+
+choice
+	prompt "Wireless Module on ttyS2"
+	default BOARD_MRMT_WIRELESS_ZB
+
+config BOARD_MRMT_WIRELESS_ZB
+	bool "Use ZigBee/802.15.4 Module"
+
+config BOARD_MRMT_WIRELESS_BT
+	bool "Use Bluetooth (HCI) Module"
+
+config BOARD_MRMT_WIRELESS_NONE
+	bool "Not Installed"
+endchoice

arch/avr32/boards/atngw100/Makefile

 obj-y					+= setup.o flash.o
 obj-$(CONFIG_BOARD_ATNGW100_EVKLCD10X)	+= evklcd10x.o
+obj-$(CONFIG_BOARD_ATNGW100_MRMT)	+= mrmt.o

arch/avr32/boards/atngw100/setup.c

@@ -56,8 +56,13 @@ static struct spi_board_info spi0_board_info[] __initdata = {
 static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
+#if defined(CONFIG_BOARD_ATNGW100_EVKLCD10X) || defined(CONFIG_BOARD_ATNGW100_MRMT1)
+		.detect_pin     = GPIO_PIN_NONE,
+		.wp_pin         = GPIO_PIN_NONE,
+#else
 		.detect_pin	= GPIO_PIN_PC(25),
 		.wp_pin		= GPIO_PIN_PE(0),
+#endif
 	},
 };
 

arch/avr32/boards/merisc/setup.c

@@ -97,6 +97,7 @@ static struct mci_platform_data __initdata mci0_data = {
 		.bus_width		= 4,
 		.detect_pin		= GPIO_PIN_PE(19),
 		.wp_pin			= GPIO_PIN_PE(20),
+		.detect_is_active_high	= true,
 	},
 };
 

arch/avr32/include/asm/hw_irq.h

 #ifndef __ASM_AVR32_HW_IRQ_H
 #define __ASM_AVR32_HW_IRQ_H
 
-static inline void hw_resend_irq(struct hw_interrupt_type *h, unsigned int i)
+static inline void hw_resend_irq(struct irq_chip *h, unsigned int i)
 {
 	/* Nothing to do */
 }

drivers/mmc/host/atmel-mci.c

@@ -177,6 +177,7 @@ struct atmel_mci {
  *	available.
  * @wp_pin: GPIO pin used for card write protect sending, or negative
  *	if not available.
+ * @detect_is_active_high: The state of the detect pin when it is active.
  * @detect_timer: Timer used for debouncing @detect_pin interrupts.
  */
 struct atmel_mci_slot {
@@ -196,6 +197,7 @@ struct atmel_mci_slot {
 
 	int			detect_pin;
 	int			wp_pin;
+	bool			detect_is_active_high;
 
 	struct timer_list	detect_timer;
 };
@@ -924,7 +926,8 @@ static int atmci_get_cd(struct mmc_host *mmc)
 	struct atmel_mci_slot	*slot = mmc_priv(mmc);
 
 	if (gpio_is_valid(slot->detect_pin)) {
-		present = !gpio_get_value(slot->detect_pin);
+		present = !(gpio_get_value(slot->detect_pin) ^
+			    slot->detect_is_active_high);
 		dev_dbg(&mmc->class_dev, "card is %spresent\n",
 				present ? "" : "not ");
 	}
@@ -1028,7 +1031,8 @@ static void atmci_detect_change(unsigned long data)
 		return;
 
 	enable_irq(gpio_to_irq(slot->detect_pin));
-	present = !gpio_get_value(slot->detect_pin);
+	present = !(gpio_get_value(slot->detect_pin) ^
+		    slot->detect_is_active_high);
 	present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
 
 	dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
@@ -1456,6 +1460,7 @@ static int __init atmci_init_slot(struct atmel_mci *host,
 	slot->host = host;
 	slot->detect_pin = slot_data->detect_pin;
 	slot->wp_pin = slot_data->wp_pin;
+	slot->detect_is_active_high = slot_data->detect_is_active_high;
 	slot->sdc_reg = sdc_reg;
 
 	mmc->ops = &atmci_ops;
@@ -1477,7 +1482,8 @@ static int __init atmci_init_slot(struct atmel_mci *host,
 		if (gpio_request(slot->detect_pin, "mmc_detect")) {
 			dev_dbg(&mmc->class_dev, "no detect pin available\n");
 			slot->detect_pin = -EBUSY;
-		} else if (gpio_get_value(slot->detect_pin)) {
+		} else if (gpio_get_value(slot->detect_pin) ^
+				slot->detect_is_active_high) {
 			clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
 		}
 	}

include/linux/atmel-mci.h

@@ -10,6 +10,7 @@
  * @bus_width: Number of data lines wired up the slot
  * @detect_pin: GPIO pin wired to the card detect switch
  * @wp_pin: GPIO pin wired to the write protect sensor
+ * @detect_is_active_high: The state of the detect pin when it is active
  *
  * If a given slot is not present on the board, @bus_width should be
  * set to 0. The other fields are ignored in this case.
@@ -24,6 +25,7 @@ struct mci_slot_pdata {
 	unsigned int		bus_width;
 	int			detect_pin;
 	int			wp_pin;
+	bool			detect_is_active_high;
 };
 
 /**