Commit fcdc2ea7 authored by Igor Plyatov's avatar Igor Plyatov Committed by Nicolas Ferre

AT91: Support for gsia18s board

The GS_IA18_S (GMS) is a carrier board from GeoSIG Ltd used with the
Stamp9G20 SoM from Taskit company.
It operate as an internet accelerometer.
Signed-off-by: default avatarIgor Plyatov <plyatov@gmail.com>
[nicolas.ferre@atmel.com: rm Kconfig, whitespace fixes, change machine name]
Signed-off-by: default avatarNicolas Ferre <nicolas.ferre@atmel.com>
parent 0fb55d3b
......@@ -387,6 +387,13 @@ config MACH_PCONTROL_G20
Select this if you are using taskit's Stamp9G20 CPU module on this
carrier board, beeing the decentralized unit of a building automation
system; featuring nvram, eth-switch, iso-rs485, display, io
config MACH_GSIA18S
bool "GS_IA18_S board"
help
This enables support for the GS_IA18_S board
produced by GeoSIG Ltd company. This is an internet accelerograph.
<http://www.geosig.com>
endif
if (ARCH_AT91SAM9260 || ARCH_AT91SAM9G20)
......
......@@ -67,6 +67,7 @@ obj-$(CONFIG_MACH_ACMENETUSFOXG20) += board-foxg20.o
obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o
obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o
obj-$(CONFIG_MACH_PCONTROL_G20) += board-pcontrol-g20.o board-stamp9g20.o
obj-$(CONFIG_MACH_GSIA18S) += board-gsia18s.o board-stamp9g20.o
# AT91SAM9260/AT91SAM9G20 board-specific support
obj-$(CONFIG_MACH_SNAPPER_9260) += board-snapper9260.o
......
This diff is collapsed.
/* Buttons */
#define GPIO_TRIG_NET_IN AT91_PIN_PB21
#define GPIO_CARD_UNMOUNT_0 AT91_PIN_PB13
#define GPIO_CARD_UNMOUNT_1 AT91_PIN_PB12
#define GPIO_KEY_POWER AT91_PIN_PA25
/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */
#define GS_IA18_S_PCF_GPIO_BASE0 NR_BUILTIN_GPIO
#define PCF_GPIO_HDC_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 0)
#define PCF_GPIO_WIFI_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 1)
#define PCF_GPIO_WIFI_ENABLE (GS_IA18_S_PCF_GPIO_BASE0 + 2)
#define PCF_GPIO_WIFI_RESET (GS_IA18_S_PCF_GPIO_BASE0 + 3)
#define PCF_GPIO_ETH_DETECT 4 /* this is a GPI */
#define PCF_GPIO_GPS_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 5)
#define PCF_GPIO_GPS_STANDBY (GS_IA18_S_PCF_GPIO_BASE0 + 6)
#define PCF_GPIO_GPS_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 7)
/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
#define GS_IA18_S_PCF_GPIO_BASE1 (GS_IA18_S_PCF_GPIO_BASE0 + 8)
#define PCF_GPIO_ALARM1 (GS_IA18_S_PCF_GPIO_BASE1 + 0)
#define PCF_GPIO_ALARM2 (GS_IA18_S_PCF_GPIO_BASE1 + 1)
#define PCF_GPIO_ALARM3 (GS_IA18_S_PCF_GPIO_BASE1 + 2)
#define PCF_GPIO_ALARM4 (GS_IA18_S_PCF_GPIO_BASE1 + 3)
/* bits 4, 5, 6 not used */
#define PCF_GPIO_ALARM_V_RELAY_ON (GS_IA18_S_PCF_GPIO_BASE1 + 7)
/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */
#define GS_IA18_S_PCF_GPIO_BASE2 (GS_IA18_S_PCF_GPIO_BASE1 + 8)
#define PCF_GPIO_MODEM_POWER (GS_IA18_S_PCF_GPIO_BASE2 + 0)
#define PCF_GPIO_MODEM_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 3)
/* bits 1, 2, 4, 5 not used */
#define PCF_GPIO_TRX_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 6)
/* bit 7 not used */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment