i40e: Add functions to blink led on 10GBaseT PHY

This patch adds functions to blink led on devices using
10GBaseT PHY since MAC registers used in other designs
do not work in this device configuration.

Change-ID: Id4b88c93c649fd2b88073a00b42867a77c761ca3
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/i40e/i40e_common.c

@@ -4214,3 +4214,332 @@ i40e_status i40e_aq_configure_partition_bw(struct i40e_hw *hw,
 
 	return status;
 }
+
+/**
+ * i40e_read_phy_register
+ * @hw: pointer to the HW structure
+ * @page: registers page number
+ * @reg: register address in the page
+ * @phy_adr: PHY address on MDIO interface
+ * @value: PHY register value
+ *
+ * Reads specified PHY register value
+ **/
+i40e_status i40e_read_phy_register(struct i40e_hw *hw,
+				   u8 page, u16 reg, u8 phy_addr,
+				   u16 *value)
+{
+	i40e_status status = I40E_ERR_TIMEOUT;
+	u32 command = 0;
+	u16 retry = 1000;
+	u8 port_num = hw->func_caps.mdio_port_num;
+
+	command = (reg << I40E_GLGEN_MSCA_MDIADD_SHIFT) |
+		  (page << I40E_GLGEN_MSCA_DEVADD_SHIFT) |
+		  (phy_addr << I40E_GLGEN_MSCA_PHYADD_SHIFT) |
+		  (I40E_MDIO_OPCODE_ADDRESS) |
+		  (I40E_MDIO_STCODE) |
+		  (I40E_GLGEN_MSCA_MDICMD_MASK) |
+		  (I40E_GLGEN_MSCA_MDIINPROGEN_MASK);
+	wr32(hw, I40E_GLGEN_MSCA(port_num), command);
+	do {
+		command = rd32(hw, I40E_GLGEN_MSCA(port_num));
+		if (!(command & I40E_GLGEN_MSCA_MDICMD_MASK)) {
+			status = 0;
+			break;
+		}
+		usleep_range(10, 20);
+		retry--;
+	} while (retry);
+
+	if (status) {
+		i40e_debug(hw, I40E_DEBUG_PHY,
+			   "PHY: Can't write command to external PHY.\n");
+		goto phy_read_end;
+	}
+
+	command = (page << I40E_GLGEN_MSCA_DEVADD_SHIFT) |
+		  (phy_addr << I40E_GLGEN_MSCA_PHYADD_SHIFT) |
+		  (I40E_MDIO_OPCODE_READ) |
+		  (I40E_MDIO_STCODE) |
+		  (I40E_GLGEN_MSCA_MDICMD_MASK) |
+		  (I40E_GLGEN_MSCA_MDIINPROGEN_MASK);
+	status = I40E_ERR_TIMEOUT;
+	retry = 1000;
+	wr32(hw, I40E_GLGEN_MSCA(port_num), command);
+	do {
+		command = rd32(hw, I40E_GLGEN_MSCA(port_num));
+		if (!(command & I40E_GLGEN_MSCA_MDICMD_MASK)) {
+			status = 0;
+			break;
+		}
+		usleep_range(10, 20);
+		retry--;
+	} while (retry);
+
+	if (!status) {
+		command = rd32(hw, I40E_GLGEN_MSRWD(port_num));
+		*value = (command & I40E_GLGEN_MSRWD_MDIRDDATA_MASK) >>
+			 I40E_GLGEN_MSRWD_MDIRDDATA_SHIFT;
+	} else {
+		i40e_debug(hw, I40E_DEBUG_PHY,
+			   "PHY: Can't read register value from external PHY.\n");
+	}
+
+phy_read_end:
+	return status;
+}
+
+/**
+ * i40e_write_phy_register
+ * @hw: pointer to the HW structure
+ * @page: registers page number
+ * @reg: register address in the page
+ * @phy_adr: PHY address on MDIO interface
+ * @value: PHY register value
+ *
+ * Writes value to specified PHY register
+ **/
+i40e_status i40e_write_phy_register(struct i40e_hw *hw,
+				    u8 page, u16 reg, u8 phy_addr,
+				    u16 value)
+{
+	i40e_status status = I40E_ERR_TIMEOUT;
+	u32 command = 0;
+	u16 retry = 1000;
+	u8 port_num = hw->func_caps.mdio_port_num;
+
+	command = (reg << I40E_GLGEN_MSCA_MDIADD_SHIFT) |
+		  (page << I40E_GLGEN_MSCA_DEVADD_SHIFT) |
+		  (phy_addr << I40E_GLGEN_MSCA_PHYADD_SHIFT) |
+		  (I40E_MDIO_OPCODE_ADDRESS) |
+		  (I40E_MDIO_STCODE) |
+		  (I40E_GLGEN_MSCA_MDICMD_MASK) |
+		  (I40E_GLGEN_MSCA_MDIINPROGEN_MASK);
+	wr32(hw, I40E_GLGEN_MSCA(port_num), command);
+	do {
+		command = rd32(hw, I40E_GLGEN_MSCA(port_num));
+		if (!(command & I40E_GLGEN_MSCA_MDICMD_MASK)) {
+			status = 0;
+			break;
+		}
+		usleep_range(10, 20);
+		retry--;
+	} while (retry);
+	if (status) {
+		i40e_debug(hw, I40E_DEBUG_PHY,
+			   "PHY: Can't write command to external PHY.\n");
+		goto phy_write_end;
+	}
+
+	command = value << I40E_GLGEN_MSRWD_MDIWRDATA_SHIFT;
+	wr32(hw, I40E_GLGEN_MSRWD(port_num), command);
+
+	command = (page << I40E_GLGEN_MSCA_DEVADD_SHIFT) |
+		  (phy_addr << I40E_GLGEN_MSCA_PHYADD_SHIFT) |
+		  (I40E_MDIO_OPCODE_WRITE) |
+		  (I40E_MDIO_STCODE) |
+		  (I40E_GLGEN_MSCA_MDICMD_MASK) |
+		  (I40E_GLGEN_MSCA_MDIINPROGEN_MASK);
+	status = I40E_ERR_TIMEOUT;
+	retry = 1000;
+	wr32(hw, I40E_GLGEN_MSCA(port_num), command);
+	do {
+		command = rd32(hw, I40E_GLGEN_MSCA(port_num));
+		if (!(command & I40E_GLGEN_MSCA_MDICMD_MASK)) {
+			status = 0;
+			break;
+		}
+		usleep_range(10, 20);
+		retry--;
+	} while (retry);
+
+phy_write_end:
+	return status;
+}
+
+/**
+ * i40e_get_phy_address
+ * @hw: pointer to the HW structure
+ * @dev_num: PHY port num that address we want
+ * @phy_addr: Returned PHY address
+ *
+ * Gets PHY address for current port
+ **/
+u8 i40e_get_phy_address(struct i40e_hw *hw, u8 dev_num)
+{
+	u8 port_num = hw->func_caps.mdio_port_num;
+	u32 reg_val = rd32(hw, I40E_GLGEN_MDIO_I2C_SEL(port_num));
+
+	return (u8)(reg_val >> ((dev_num + 1) * 5)) & 0x1f;
+}
+
+/**
+ * i40e_blink_phy_led
+ * @hw: pointer to the HW structure
+ * @time: time how long led will blinks in secs
+ * @interval: gap between LED on and off in msecs
+ *
+ * Blinks PHY link LED
+ **/
+i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
+				    u32 time, u32 interval)
+{
+	i40e_status status = 0;
+	u32 i;
+	u16 led_ctl;
+	u16 gpio_led_port;
+	u16 led_reg;
+	u16 led_addr = I40E_PHY_LED_PROV_REG_1;
+	u8 phy_addr = 0;
+	u8 port_num;
+
+	i = rd32(hw, I40E_PFGEN_PORTNUM);
+	port_num = (u8)(i & I40E_PFGEN_PORTNUM_PORT_NUM_MASK);
+	phy_addr = i40e_get_phy_address(hw, port_num);
+
+	for (gpio_led_port = 0; gpio_led_port < 3; gpio_led_port++,
+	     led_addr++) {
+		status = i40e_read_phy_register(hw, I40E_PHY_COM_REG_PAGE,
+						led_addr, phy_addr, &led_reg);
+		if (status)
+			goto phy_blinking_end;
+		led_ctl = led_reg;
+		if (led_reg & I40E_PHY_LED_LINK_MODE_MASK) {
+			led_reg = 0;
+			status = i40e_write_phy_register(hw,
+							 I40E_PHY_COM_REG_PAGE,
+							 led_addr, phy_addr,
+							 led_reg);
+			if (status)
+				goto phy_blinking_end;
+			break;
+		}
+	}
+
+	if (time > 0 && interval > 0) {
+		for (i = 0; i < time * 1000; i += interval) {
+			status = i40e_read_phy_register(hw,
+							I40E_PHY_COM_REG_PAGE,
+							led_addr, phy_addr,
+							&led_reg);
+			if (status)
+				goto restore_config;
+			if (led_reg & I40E_PHY_LED_MANUAL_ON)
+				led_reg = 0;
+			else
+				led_reg = I40E_PHY_LED_MANUAL_ON;
+			status = i40e_write_phy_register(hw,
+							 I40E_PHY_COM_REG_PAGE,
+							 led_addr, phy_addr,
+							 led_reg);
+			if (status)
+				goto restore_config;
+			msleep(interval);
+		}
+	}
+
+restore_config:
+	status = i40e_write_phy_register(hw, I40E_PHY_COM_REG_PAGE, led_addr,
+					 phy_addr, led_ctl);
+
+phy_blinking_end:
+	return status;
+}
+
+/**
+ * i40e_led_get_phy - return current on/off mode
+ * @hw: pointer to the hw struct
+ * @led_addr: address of led register to use
+ * @val: original value of register to use
+ *
+ **/
+i40e_status i40e_led_get_phy(struct i40e_hw *hw, u16 *led_addr,
+			     u16 *val)
+{
+	i40e_status status = 0;
+	u16 gpio_led_port;
+	u8 phy_addr = 0;
+	u16 reg_val;
+	u16 temp_addr;
+	u8 port_num;
+	u32 i;
+
+	temp_addr = I40E_PHY_LED_PROV_REG_1;
+	i = rd32(hw, I40E_PFGEN_PORTNUM);
+	port_num = (u8)(i & I40E_PFGEN_PORTNUM_PORT_NUM_MASK);
+	phy_addr = i40e_get_phy_address(hw, port_num);
+
+	for (gpio_led_port = 0; gpio_led_port < 3; gpio_led_port++,
+	     temp_addr++) {
+		status = i40e_read_phy_register(hw, I40E_PHY_COM_REG_PAGE,
+						temp_addr, phy_addr, &reg_val);
+		if (status)
+			return status;
+		*val = reg_val;
+		if (reg_val & I40E_PHY_LED_LINK_MODE_MASK) {
+			*led_addr = temp_addr;
+			break;
+		}
+	}
+	return status;
+}
+
+/**
+ * i40e_led_set_phy
+ * @hw: pointer to the HW structure
+ * @on: true or false
+ * @mode: original val plus bit for set or ignore
+ * Set led's on or off when controlled by the PHY
+ *
+ **/
+i40e_status i40e_led_set_phy(struct i40e_hw *hw, bool on,
+			     u16 led_addr, u32 mode)
+{
+	i40e_status status = 0;
+	u16 led_ctl = 0;
+	u16 led_reg = 0;
+	u8 phy_addr = 0;
+	u8 port_num;
+	u32 i;
+
+	i = rd32(hw, I40E_PFGEN_PORTNUM);
+	port_num = (u8)(i & I40E_PFGEN_PORTNUM_PORT_NUM_MASK);
+	phy_addr = i40e_get_phy_address(hw, port_num);
+
+	status = i40e_read_phy_register(hw, I40E_PHY_COM_REG_PAGE, led_addr,
+					phy_addr, &led_reg);
+	if (status)
+		return status;
+	led_ctl = led_reg;
+	if (led_reg & I40E_PHY_LED_LINK_MODE_MASK) {
+		led_reg = 0;
+		status = i40e_write_phy_register(hw, I40E_PHY_COM_REG_PAGE,
+						 led_addr, phy_addr, led_reg);
+		if (status)
+			return status;
+	}
+	status = i40e_read_phy_register(hw, I40E_PHY_COM_REG_PAGE,
+					led_addr, phy_addr, &led_reg);
+	if (status)
+		goto restore_config;
+	if (on)
+		led_reg = I40E_PHY_LED_MANUAL_ON;
+	else
+		led_reg = 0;
+	status = i40e_write_phy_register(hw, I40E_PHY_COM_REG_PAGE,
+					 led_addr, phy_addr, led_reg);
+	if (status)
+		goto restore_config;
+	if (mode & I40E_PHY_LED_MODE_ORIG) {
+		led_ctl = (mode & I40E_PHY_LED_MODE_MASK);
+		status = i40e_write_phy_register(hw,
+						 I40E_PHY_COM_REG_PAGE,
+						 led_addr, phy_addr, led_ctl);
+	}
+	return status;
+restore_config:
+	status = i40e_write_phy_register(hw, I40E_PHY_COM_REG_PAGE, led_addr,
+					 phy_addr, led_ctl);
+	return status;
+}

drivers/net/ethernet/intel/i40e/i40e_prototype.h

@@ -74,6 +74,12 @@ i40e_status i40e_aq_set_rss_key(struct i40e_hw *hw,
 
 u32 i40e_led_get(struct i40e_hw *hw);
 void i40e_led_set(struct i40e_hw *hw, u32 mode, bool blink);
+i40e_status i40e_led_set_phy(struct i40e_hw *hw, bool on,
+			     u16 led_addr, u32 mode);
+i40e_status i40e_led_get_phy(struct i40e_hw *hw, u16 *led_addr,
+			     u16 *val);
+i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
+				    u32 time, u32 interval);
 
 /* admin send queue commands */
 
@@ -336,4 +342,11 @@ i40e_status i40e_aq_debug_dump(struct i40e_hw *hw, u8 cluster_id,
 			       struct i40e_asq_cmd_details *cmd_details);
 void i40e_add_filter_to_drop_tx_flow_control_frames(struct i40e_hw *hw,
 						    u16 vsi_seid);
+i40e_status i40e_read_phy_register(struct i40e_hw *hw, u8 page,
+				   u16 reg, u8 phy_addr, u16 *value);
+i40e_status i40e_write_phy_register(struct i40e_hw *hw, u8 page,
+				    u16 reg, u8 phy_addr, u16 value);
+u8 i40e_get_phy_address(struct i40e_hw *hw, u8 dev_num);
+i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
+				    u32 time, u32 interval);
 #endif /* _I40E_PROTOTYPE_H_ */

drivers/net/ethernet/intel/i40e/i40e_type.h

@@ -90,6 +90,22 @@ enum i40e_debug_mask {
 	I40E_DEBUG_ALL			= 0xFFFFFFFF
 };
 
+#define I40E_MDIO_STCODE                0
+#define I40E_MDIO_OPCODE_ADDRESS        0
+#define I40E_MDIO_OPCODE_WRITE          I40E_MASK(1, \
+						  I40E_GLGEN_MSCA_OPCODE_SHIFT)
+#define I40E_MDIO_OPCODE_READ_INC_ADDR  I40E_MASK(2, \
+						  I40E_GLGEN_MSCA_OPCODE_SHIFT)
+#define I40E_MDIO_OPCODE_READ           I40E_MASK(3, \
+						  I40E_GLGEN_MSCA_OPCODE_SHIFT)
+
+#define I40E_PHY_COM_REG_PAGE                   0x1E
+#define I40E_PHY_LED_LINK_MODE_MASK             0xF0
+#define I40E_PHY_LED_MANUAL_ON                  0x100
+#define I40E_PHY_LED_PROV_REG_1                 0xC430
+#define I40E_PHY_LED_MODE_MASK                  0xFFFF
+#define I40E_PHY_LED_MODE_ORIG                  0x80000000
+
 /* These are structs for managing the hardware information and the operations.
  * The structures of function pointers are filled out at init time when we
  * know for sure exactly which hardware we're working with.  This gives us the

drivers/net/ethernet/intel/i40evf/i40e_prototype.h

@@ -103,4 +103,11 @@ i40e_status i40e_aq_add_rem_control_packet_filter(struct i40e_hw *hw,
 				struct i40e_asq_cmd_details *cmd_details);
 void i40e_add_filter_to_drop_tx_flow_control_frames(struct i40e_hw *hw,
 						    u16 vsi_seid);
+i40e_status i40e_read_phy_register(struct i40e_hw *hw, u8 page,
+				   u16 reg, u8 phy_addr, u16 *value);
+i40e_status i40e_write_phy_register(struct i40e_hw *hw, u8 page,
+				    u16 reg, u8 phy_addr, u16 value);
+u8 i40e_get_phy_address(struct i40e_hw *hw, u8 dev_num);
+i40e_status i40e_blink_phy_link_led(struct i40e_hw *hw,
+				    u32 time, u32 interval);
 #endif /* _I40E_PROTOTYPE_H_ */