Merge tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu into next/dt

Merge "mvebu/dt #2" from Andrew Lunn:

Second set of dt patches for mvebu for v3.20.

* tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: make DTS comments reflect DEBUG_LL changes
  ARM: mvebu: Armada 385 GP: Add regulators to the SATA port
  ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
  ARM: mvebu: fix compatible strings of MBus on Armada 375 and Armada 38x
  dt: bindings: update mvebu-mbus DT binding with new compatible properties
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/bus/mvebu-mbus.txt

@@ -6,8 +6,8 @@ Required properties:
 - compatible:	 Should be set to one of the following:
 		 marvell,armada370-mbus
 		 marvell,armadaxp-mbus
-		 marvell,armada370-mbus
-		 marvell,armadaxp-mbus
+		 marvell,armada375-mbus
+		 marvell,armada380-mbus
 		 marvell,kirkwood-mbus
 		 marvell,dove-mbus
 		 marvell,orion5x-88f5281-mbus

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -35,6 +35,7 @@ chipidea	Chipidea, Inc
 chrp	Common Hardware Reference Platform
 chunghwa	Chunghwa Picture Tubes Ltd.
 cirrus	Cirrus Logic, Inc.
+cloudengines	Cloud Engines, Inc.
 cnm	Chips&Media, Inc.
 cortina	Cortina Systems, Inc.
 crystalfontz	Crystalfontz America, Inc.

arch/arm/boot/dts/Makefile

@@ -187,6 +187,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
 	kirkwood-openrd-base.dtb \
 	kirkwood-openrd-client.dtb \
 	kirkwood-openrd-ultimate.dtb \
+	kirkwood-pogo_e02.dtb \
 	kirkwood-rd88f6192.dtb \
 	kirkwood-rd88f6281-z0.dtb \
 	kirkwood-rd88f6281-a.dtb \

arch/arm/boot/dts/armada-375.dtsi

@@ -63,7 +63,7 @@ cpu@1 {
 	};
 
 	soc {
-		compatible = "marvell,armada375-mbus", "marvell,armada370-mbus", "simple-bus";
+		compatible = "marvell,armada375-mbus", "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
 		controller = <&mbusc>;

arch/arm/boot/dts/armada-388-gp.dts

@@ -173,6 +173,16 @@ sata@a8000 {
 				status = "okay";
 				#address-cells = <1>;
 				#size-cells = <0>;
+
+				sata0: sata-port@0 {
+					reg = <0>;
+					target-supply = <&reg_5v_sata0>;
+				};
+
+				sata1: sata-port@1 {
+					reg = <1>;
+					target-supply = <&reg_5v_sata1>;
+				};
 			};
 
 			sata@e0000 {
@@ -181,6 +191,16 @@ sata@e0000 {
 				status = "okay";
 				#address-cells = <1>;
 				#size-cells = <0>;
+
+				sata2: sata-port@0 {
+					reg = <0>;
+					target-supply = <&reg_5v_sata2>;
+				};
+
+				sata3: sata-port@1 {
+					reg = <1>;
+					target-supply = <&reg_5v_sata3>;
+				};
 			};
 
 			sdhci@d8000 {
@@ -278,6 +298,112 @@ reg_usb2_1_vbus: v5-vbus1 {
 		regulator-always-on;
 		gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
 	};
+
+	reg_sata0: pwr-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata0";
+		enable-active-high;
+		regulator-always-on;
+
+	};
+
+	reg_5v_sata0: v5-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata0>;
+	};
+
+	reg_12v_sata0: v12-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata0>;
+	};
+
+	reg_sata1: pwr-sata1 {
+		regulator-name = "pwr_en_sata1";
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata1: v5-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata1>;
+	};
+
+	reg_12v_sata1: v12-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata1";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata1>;
+	};
+
+	reg_sata2: pwr-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata2";
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata2: v5-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata2";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata2>;
+	};
+
+	reg_12v_sata2: v12-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata2";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata2>;
+	};
+
+	reg_sata3: pwr-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata3";
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata3: v5-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata3";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata3>;
+	};
+
+	reg_12v_sata3: v12-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata3";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata3>;
+	};
 };
 
 &pinctrl {

arch/arm/boot/dts/armada-38x.dtsi

@@ -31,8 +31,7 @@ aliases {
 	};
 
 	soc {
-		compatible = "marvell,armada380-mbus", "marvell,armada370-mbus",
-			     "simple-bus";
+		compatible = "marvell,armada380-mbus", "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <1>;
 		controller = <&mbusc>;

arch/arm/boot/dts/armada-xp-axpwifiap.dts

@@ -3,8 +3,8 @@
  *
  * Note: this board is shipped with a new generation boot loader that
  * remaps internal registers at 0xf1000000. Therefore, if earlyprintk
- * is used, the CONFIG_DEBUG_MVEBU_UART_ALTERNATE option should be
- * used.
+ * is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option or the
+ * CONFIG_DEBUG_MVEBU_UART1_ALTERNATE option should be used.
  *
  * Copyright (C) 2013 Marvell
  *
@@ -60,10 +60,12 @@ pcie@3,0 {
 		};
 
 		internal-regs {
+			/* UART0 */
 			serial@12000 {
 				status = "okay";
 			};
 
+			/* UART1 */
 			serial@12100 {
 				status = "okay";
 			};

arch/arm/boot/dts/kirkwood-pogo_e02.dts

+/*
+ * kirkwood-pogo_e02.dts - Device tree file for Pogoplug E02
+ *
+ * Copyright (C) 2015 Christoph Junghans <ottxor@gentoo.org>
+ *
+ * based on information of dts files from
+ *  Arch Linux ARM by Oleg Rakhmanov <moonman.ca@gmail.com>
+ *  OpenWrt by Felix Kaechele <heffer@fedoraproject.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Cloud Engines Pogoplug E02";
+	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281",
+		     "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		health {
+			label = "pogo_e02:green:health";
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		fault {
+			label = "pogo_e02:orange:fault";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+		      &pmx_led_green >;
+	pinctrl-names = "default";
+
+	pmx_usb_power_enable: pmx-usb-power-enable {
+		marvell,pins = "mpp29";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_green: pmx-led-green {
+		marvell,pins = "mpp48";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_orange: pmx-led-orange {
+		marvell,pins = "mpp49";
+		marvell,function = "gpio";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&nand {
+	chip-delay = <40>;
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition@500000 {
+		label = "pogoplug";
+		reg = <0x0500000 0x2000000>;
+	};
+
+	partition@2500000 {
+		label = "root";
+		reg = <0x02500000 0x5b00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};