Commit fe504c5c authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'boards2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC board updates, take 2 from Olof Johansson:
 "This branch contains board updates for shmobile that had dependencies
  on earlier branches past the first driver branch, and thus are merged
  separately.

  Most of these are to enable audio and USB on shmobile.  They contain a
  dependent ASoC branch that has been coordinated with Mark Brown."

* tag 'boards2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: shmobile: mackerel: Add FLCTL IRQ resource
  ARM: shmobile: use FSI driver's audio clock on ap4evb
  ARM: shmobile: use FSI driver's audio clock on mackerel
  ARM: shmobile: use FSI driver's audio clock on armadillo800eva
  ARM: shmobile: mackerel: enable DMAEngine on USB Host
  ARM: shmobile: marzen: add USB OHCI driver support
  ARM: shmobile: marzen: add USB EHCI driver support
  ARM: shmobile: marzen: add USB phy support
  ASoC: fsi: add master clock control functions
  ASoC: fsi: care fsi_hw_start/stop() return value
  ASoC: fsi: fsi_set_master_clk() was called from fsi_hw_xxx() only
  ASoC: fsi: use devm_request_irq()
  ASoC: fsi: fixup channels_min/max
parents 698d6012 d7460f4a
...@@ -47,6 +47,8 @@ CONFIG_DEVTMPFS_MOUNT=y ...@@ -47,6 +47,8 @@ CONFIG_DEVTMPFS_MOUNT=y
# CONFIG_STANDALONE is not set # CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set # CONFIG_PREVENT_FIRMWARE_BUILD is not set
# CONFIG_FW_LOADER is not set # CONFIG_FW_LOADER is not set
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_NETDEVICES=y CONFIG_NETDEVICES=y
# CONFIG_NET_VENDOR_BROADCOM is not set # CONFIG_NET_VENDOR_BROADCOM is not set
# CONFIG_NET_VENDOR_FARADAY is not set # CONFIG_NET_VENDOR_FARADAY is not set
...@@ -59,9 +61,8 @@ CONFIG_SMSC911X=y ...@@ -59,9 +61,8 @@ CONFIG_SMSC911X=y
# CONFIG_NET_VENDOR_STMICRO is not set # CONFIG_NET_VENDOR_STMICRO is not set
# CONFIG_WLAN is not set # CONFIG_WLAN is not set
# CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_KEYBOARD is not set CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_MOUSE is not set # CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
# CONFIG_VT is not set # CONFIG_VT is not set
# CONFIG_LEGACY_PTYS is not set # CONFIG_LEGACY_PTYS is not set
# CONFIG_DEVKMEM is not set # CONFIG_DEVKMEM is not set
...@@ -78,9 +79,16 @@ CONFIG_GPIO_SYSFS=y ...@@ -78,9 +79,16 @@ CONFIG_GPIO_SYSFS=y
CONFIG_THERMAL=y CONFIG_THERMAL=y
CONFIG_RCAR_THERMAL=y CONFIG_RCAR_THERMAL=y
CONFIG_SSB=y CONFIG_SSB=y
# CONFIG_USB_SUPPORT is not set CONFIG_USB=y
CONFIG_USB_RCAR_PHY=y
CONFIG_MMC=y CONFIG_MMC=y
CONFIG_MMC_SDHI=y CONFIG_MMC_SDHI=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_PLATFORM=y
CONFIG_USB_EHCI_HCD_PLATFORM=y
CONFIG_USB_STORAGE=y
CONFIG_UIO=y CONFIG_UIO=y
CONFIG_UIO_PDRV_GENIRQ=y CONFIG_UIO_PDRV_GENIRQ=y
# CONFIG_IOMMU_SUPPORT is not set # CONFIG_IOMMU_SUPPORT is not set
......
...@@ -29,6 +29,8 @@ config ARCH_R8A7779 ...@@ -29,6 +29,8 @@ config ARCH_R8A7779
select ARM_GIC select ARM_GIC
select CPU_V7 select CPU_V7
select SH_CLK_CPG select SH_CLK_CPG
select USB_ARCH_HAS_EHCI
select USB_ARCH_HAS_OHCI
config ARCH_EMEV2 config ARCH_EMEV2
bool "Emma Mobile EV2" bool "Emma Mobile EV2"
......
...@@ -658,133 +658,16 @@ static struct platform_device lcdc_device = { ...@@ -658,133 +658,16 @@ static struct platform_device lcdc_device = {
/* FSI */ /* FSI */
#define IRQ_FSI evt2irq(0x1840) #define IRQ_FSI evt2irq(0x1840)
static int __fsi_set_rate(struct clk *clk, long rate, int enable)
{
int ret = 0;
if (rate <= 0)
return ret;
if (enable) {
ret = clk_set_rate(clk, rate);
if (0 == ret)
ret = clk_enable(clk);
} else {
clk_disable(clk);
}
return ret;
}
static int __fsi_set_round_rate(struct clk *clk, long rate, int enable)
{
return __fsi_set_rate(clk, clk_round_rate(clk, rate), enable);
}
static int fsi_ak4642_set_rate(struct device *dev, int rate, int enable)
{
struct clk *fsia_ick;
struct clk *fsiack;
int ret = -EIO;
fsia_ick = clk_get(dev, "icka");
if (IS_ERR(fsia_ick))
return PTR_ERR(fsia_ick);
/*
* FSIACK is connected to AK4642,
* and use external clock pin from it.
* it is parent of fsia_ick now.
*/
fsiack = clk_get_parent(fsia_ick);
if (!fsiack)
goto fsia_ick_out;
/*
* we get 1/1 divided clock by setting same rate to fsiack and fsia_ick
*
** FIXME **
* Because the freq_table of external clk (fsiack) are all 0,
* the return value of clk_round_rate became 0.
* So, it use __fsi_set_rate here.
*/
ret = __fsi_set_rate(fsiack, rate, enable);
if (ret < 0)
goto fsiack_out;
ret = __fsi_set_round_rate(fsia_ick, rate, enable);
if ((ret < 0) && enable)
__fsi_set_round_rate(fsiack, rate, 0); /* disable FSI ACK */
fsiack_out:
clk_put(fsiack);
fsia_ick_out:
clk_put(fsia_ick);
return 0;
}
static int fsi_hdmi_set_rate(struct device *dev, int rate, int enable)
{
struct clk *fsib_clk;
struct clk *fdiv_clk = clk_get(NULL, "fsidivb");
long fsib_rate = 0;
long fdiv_rate = 0;
int ackmd_bpfmd;
int ret;
switch (rate) {
case 44100:
fsib_rate = rate * 256;
ackmd_bpfmd = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
break;
case 48000:
fsib_rate = 85428000; /* around 48kHz x 256 x 7 */
fdiv_rate = rate * 256;
ackmd_bpfmd = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
break;
default:
pr_err("unsupported rate in FSI2 port B\n");
return -EINVAL;
}
/* FSI B setting */
fsib_clk = clk_get(dev, "ickb");
if (IS_ERR(fsib_clk))
return -EIO;
ret = __fsi_set_round_rate(fsib_clk, fsib_rate, enable);
if (ret < 0)
goto fsi_set_rate_end;
/* FSI DIV setting */
ret = __fsi_set_round_rate(fdiv_clk, fdiv_rate, enable);
if (ret < 0) {
/* disable FSI B */
if (enable)
__fsi_set_round_rate(fsib_clk, fsib_rate, 0);
goto fsi_set_rate_end;
}
ret = ackmd_bpfmd;
fsi_set_rate_end:
clk_put(fsib_clk);
return ret;
}
static struct sh_fsi_platform_info fsi_info = { static struct sh_fsi_platform_info fsi_info = {
.port_a = { .port_a = {
.flags = SH_FSI_BRS_INV, .flags = SH_FSI_BRS_INV,
.set_rate = fsi_ak4642_set_rate,
}, },
.port_b = { .port_b = {
.flags = SH_FSI_BRS_INV | .flags = SH_FSI_BRS_INV |
SH_FSI_BRM_INV | SH_FSI_BRM_INV |
SH_FSI_LRS_INV | SH_FSI_LRS_INV |
SH_FSI_CLK_CPG |
SH_FSI_FMT_SPDIF, SH_FSI_FMT_SPDIF,
.set_rate = fsi_hdmi_set_rate,
}, },
}; };
...@@ -1144,25 +1027,6 @@ static void __init hdmi_init_pm_clock(void) ...@@ -1144,25 +1027,6 @@ static void __init hdmi_init_pm_clock(void)
clk_put(hdmi_ick); clk_put(hdmi_ick);
} }
static void __init fsi_init_pm_clock(void)
{
struct clk *fsia_ick;
int ret;
fsia_ick = clk_get(&fsi_device.dev, "icka");
if (IS_ERR(fsia_ick)) {
ret = PTR_ERR(fsia_ick);
pr_err("Cannot get FSI ICK: %d\n", ret);
return;
}
ret = clk_set_parent(fsia_ick, &sh7372_fsiack_clk);
if (ret < 0)
pr_err("Cannot set FSI-A parent: %d\n", ret);
clk_put(fsia_ick);
}
/* TouchScreen */ /* TouchScreen */
#ifdef CONFIG_AP4EVB_QHD #ifdef CONFIG_AP4EVB_QHD
# define GPIO_TSC_IRQ GPIO_FN_IRQ28_123 # define GPIO_TSC_IRQ GPIO_FN_IRQ28_123
...@@ -1476,7 +1340,6 @@ static void __init ap4evb_init(void) ...@@ -1476,7 +1340,6 @@ static void __init ap4evb_init(void)
ARRAY_SIZE(domain_devices)); ARRAY_SIZE(domain_devices));
hdmi_init_pm_clock(); hdmi_init_pm_clock();
fsi_init_pm_clock();
sh7372_pm_init(); sh7372_pm_init();
pm_clk_add(&fsi_device.dev, "spu2"); pm_clk_add(&fsi_device.dev, "spu2");
pm_clk_add(&lcdc1_device.dev, "hdmi"); pm_clk_add(&lcdc1_device.dev, "hdmi");
......
...@@ -768,32 +768,6 @@ static struct platform_device ceu0_device = { ...@@ -768,32 +768,6 @@ static struct platform_device ceu0_device = {
}; };
/* FSI */ /* FSI */
static int fsi_hdmi_set_rate(struct device *dev, int rate, int enable)
{
struct clk *fsib;
int ret;
/* it support 48KHz only */
if (48000 != rate)
return -EINVAL;
fsib = clk_get(dev, "ickb");
if (IS_ERR(fsib))
return -EINVAL;
if (enable) {
ret = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
clk_enable(fsib);
} else {
ret = 0;
clk_disable(fsib);
}
clk_put(fsib);
return ret;
}
static struct sh_fsi_platform_info fsi_info = { static struct sh_fsi_platform_info fsi_info = {
/* FSI-WM8978 */ /* FSI-WM8978 */
.port_a = { .port_a = {
...@@ -802,8 +776,8 @@ static struct sh_fsi_platform_info fsi_info = { ...@@ -802,8 +776,8 @@ static struct sh_fsi_platform_info fsi_info = {
/* FSI-HDMI */ /* FSI-HDMI */
.port_b = { .port_b = {
.flags = SH_FSI_FMT_SPDIF | .flags = SH_FSI_FMT_SPDIF |
SH_FSI_ENABLE_STREAM_MODE, SH_FSI_ENABLE_STREAM_MODE |
.set_rate = fsi_hdmi_set_rate, SH_FSI_CLK_CPG,
.tx_id = SHDMA_SLAVE_FSIB_TX, .tx_id = SHDMA_SLAVE_FSIB_TX,
} }
}; };
...@@ -938,13 +912,11 @@ static void __init eva_clock_init(void) ...@@ -938,13 +912,11 @@ static void __init eva_clock_init(void)
struct clk *xtal1 = clk_get(NULL, "extal1"); struct clk *xtal1 = clk_get(NULL, "extal1");
struct clk *usb24s = clk_get(NULL, "usb24s"); struct clk *usb24s = clk_get(NULL, "usb24s");
struct clk *fsibck = clk_get(NULL, "fsibck"); struct clk *fsibck = clk_get(NULL, "fsibck");
struct clk *fsib = clk_get(&fsi_device.dev, "ickb");
if (IS_ERR(system) || if (IS_ERR(system) ||
IS_ERR(xtal1) || IS_ERR(xtal1) ||
IS_ERR(usb24s) || IS_ERR(usb24s) ||
IS_ERR(fsibck) || IS_ERR(fsibck)) {
IS_ERR(fsib)) {
pr_err("armadillo800eva board clock init failed\n"); pr_err("armadillo800eva board clock init failed\n");
goto clock_error; goto clock_error;
} }
...@@ -956,9 +928,7 @@ static void __init eva_clock_init(void) ...@@ -956,9 +928,7 @@ static void __init eva_clock_init(void)
clk_set_parent(usb24s, system); clk_set_parent(usb24s, system);
/* FSIBCK is 12.288MHz, and it is parent of FSI-B */ /* FSIBCK is 12.288MHz, and it is parent of FSI-B */
clk_set_parent(fsib, fsibck);
clk_set_rate(fsibck, 12288000); clk_set_rate(fsibck, 12288000);
clk_set_rate(fsib, 12288000);
clock_error: clock_error:
if (!IS_ERR(system)) if (!IS_ERR(system))
...@@ -969,8 +939,6 @@ static void __init eva_clock_init(void) ...@@ -969,8 +939,6 @@ static void __init eva_clock_init(void)
clk_put(usb24s); clk_put(usb24s);
if (!IS_ERR(fsibck)) if (!IS_ERR(fsibck))
clk_put(fsibck); clk_put(fsibck);
if (!IS_ERR(fsib))
clk_put(fsib);
} }
/* /*
......
...@@ -816,6 +816,8 @@ static struct platform_device usbhs1_device = { ...@@ -816,6 +816,8 @@ static struct platform_device usbhs1_device = {
.id = 1, .id = 1,
.dev = { .dev = {
.platform_data = &usbhs1_private.info, .platform_data = &usbhs1_private.info,
.dma_mask = &usbhs1_device.dev.coherent_dma_mask,
.coherent_dma_mask = DMA_BIT_MASK(32),
}, },
.num_resources = ARRAY_SIZE(usbhs1_resources), .num_resources = ARRAY_SIZE(usbhs1_resources),
.resource = usbhs1_resources, .resource = usbhs1_resources,
...@@ -860,76 +862,6 @@ static struct platform_device leds_device = { ...@@ -860,76 +862,6 @@ static struct platform_device leds_device = {
/* FSI */ /* FSI */
#define IRQ_FSI evt2irq(0x1840) #define IRQ_FSI evt2irq(0x1840)
static int __fsi_set_round_rate(struct clk *clk, long rate, int enable)
{
int ret;
if (rate <= 0)
return 0;
if (!enable) {
clk_disable(clk);
return 0;
}
ret = clk_set_rate(clk, clk_round_rate(clk, rate));
if (ret < 0)
return ret;
return clk_enable(clk);
}
static int fsi_b_set_rate(struct device *dev, int rate, int enable)
{
struct clk *fsib_clk;
struct clk *fdiv_clk = clk_get(NULL, "fsidivb");
long fsib_rate = 0;
long fdiv_rate = 0;
int ackmd_bpfmd;
int ret;
/* clock start */
switch (rate) {
case 44100:
fsib_rate = rate * 256;
ackmd_bpfmd = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
break;
case 48000:
fsib_rate = 85428000; /* around 48kHz x 256 x 7 */
fdiv_rate = rate * 256;
ackmd_bpfmd = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
break;
default:
pr_err("unsupported rate in FSI2 port B\n");
return -EINVAL;
}
/* FSI B setting */
fsib_clk = clk_get(dev, "ickb");
if (IS_ERR(fsib_clk))
return -EIO;
/* fsib */
ret = __fsi_set_round_rate(fsib_clk, fsib_rate, enable);
if (ret < 0)
goto fsi_set_rate_end;
/* FSI DIV */
ret = __fsi_set_round_rate(fdiv_clk, fdiv_rate, enable);
if (ret < 0) {
/* disable FSI B */
if (enable)
__fsi_set_round_rate(fsib_clk, fsib_rate, 0);
goto fsi_set_rate_end;
}
ret = ackmd_bpfmd;
fsi_set_rate_end:
clk_put(fsib_clk);
return ret;
}
static struct sh_fsi_platform_info fsi_info = { static struct sh_fsi_platform_info fsi_info = {
.port_a = { .port_a = {
.flags = SH_FSI_BRS_INV, .flags = SH_FSI_BRS_INV,
...@@ -940,8 +872,8 @@ static struct sh_fsi_platform_info fsi_info = { ...@@ -940,8 +872,8 @@ static struct sh_fsi_platform_info fsi_info = {
.flags = SH_FSI_BRS_INV | .flags = SH_FSI_BRS_INV |
SH_FSI_BRM_INV | SH_FSI_BRM_INV |
SH_FSI_LRS_INV | SH_FSI_LRS_INV |
SH_FSI_CLK_CPG |
SH_FSI_FMT_SPDIF, SH_FSI_FMT_SPDIF,
.set_rate = fsi_b_set_rate,
} }
}; };
...@@ -1018,7 +950,11 @@ static struct resource nand_flash_resources[] = { ...@@ -1018,7 +950,11 @@ static struct resource nand_flash_resources[] = {
.start = 0xe6a30000, .start = 0xe6a30000,
.end = 0xe6a3009b, .end = 0xe6a3009b,
.flags = IORESOURCE_MEM, .flags = IORESOURCE_MEM,
} },
[1] = {
.start = evt2irq(0x0d80), /* flstei: status error irq */
.flags = IORESOURCE_IRQ,
},
}; };
static struct sh_flctl_platform_data nand_flash_data = { static struct sh_flctl_platform_data nand_flash_data = {
......
...@@ -34,6 +34,10 @@ ...@@ -34,6 +34,10 @@
#include <linux/spi/sh_hspi.h> #include <linux/spi/sh_hspi.h>
#include <linux/mmc/sh_mobile_sdhi.h> #include <linux/mmc/sh_mobile_sdhi.h>
#include <linux/mfd/tmio.h> #include <linux/mfd/tmio.h>
#include <linux/usb/otg.h>
#include <linux/usb/ehci_pdriver.h>
#include <linux/usb/ohci_pdriver.h>
#include <linux/pm_runtime.h>
#include <mach/hardware.h> #include <mach/hardware.h>
#include <mach/r8a7779.h> #include <mach/r8a7779.h>
#include <mach/common.h> #include <mach/common.h>
...@@ -144,13 +148,185 @@ static struct platform_device hspi_device = { ...@@ -144,13 +148,185 @@ static struct platform_device hspi_device = {
.num_resources = ARRAY_SIZE(hspi_resources), .num_resources = ARRAY_SIZE(hspi_resources),
}; };
/* USB PHY */
static struct resource usb_phy_resources[] = {
[0] = {
.start = 0xffe70000,
.end = 0xffe70900 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = 0xfff70000,
.end = 0xfff70900 - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device usb_phy_device = {
.name = "rcar_usb_phy",
.resource = usb_phy_resources,
.num_resources = ARRAY_SIZE(usb_phy_resources),
};
static struct platform_device *marzen_devices[] __initdata = { static struct platform_device *marzen_devices[] __initdata = {
&eth_device, &eth_device,
&sdhi0_device, &sdhi0_device,
&thermal_device, &thermal_device,
&hspi_device, &hspi_device,
&usb_phy_device,
};
/* USB */
static struct usb_phy *phy;
static int usb_power_on(struct platform_device *pdev)
{
if (!phy)
return -EIO;
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
usb_phy_init(phy);
return 0;
}
static void usb_power_off(struct platform_device *pdev)
{
if (!phy)
return;
usb_phy_shutdown(phy);
pm_runtime_put_sync(&pdev->dev);
pm_runtime_disable(&pdev->dev);
}
static struct usb_ehci_pdata ehcix_pdata = {
.power_on = usb_power_on,
.power_off = usb_power_off,
.power_suspend = usb_power_off,
}; };
static struct resource ehci0_resources[] = {
[0] = {
.start = 0xffe70000,
.end = 0xffe70400 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = gic_spi(44),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device ehci0_device = {
.name = "ehci-platform",
.id = 0,
.dev = {
.dma_mask = &ehci0_device.dev.coherent_dma_mask,
.coherent_dma_mask = 0xffffffff,
.platform_data = &ehcix_pdata,
},
.num_resources = ARRAY_SIZE(ehci0_resources),
.resource = ehci0_resources,
};
static struct resource ehci1_resources[] = {
[0] = {
.start = 0xfff70000,
.end = 0xfff70400 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = gic_spi(45),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device ehci1_device = {
.name = "ehci-platform",
.id = 1,
.dev = {
.dma_mask = &ehci1_device.dev.coherent_dma_mask,
.coherent_dma_mask = 0xffffffff,
.platform_data = &ehcix_pdata,
},
.num_resources = ARRAY_SIZE(ehci1_resources),
.resource = ehci1_resources,
};
static struct usb_ohci_pdata ohcix_pdata = {
.power_on = usb_power_on,
.power_off = usb_power_off,
.power_suspend = usb_power_off,
};
static struct resource ohci0_resources[] = {
[0] = {
.start = 0xffe70400,
.end = 0xffe70800 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = gic_spi(44),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device ohci0_device = {
.name = "ohci-platform",
.id = 0,
.dev = {
.dma_mask = &ohci0_device.dev.coherent_dma_mask,
.coherent_dma_mask = 0xffffffff,
.platform_data = &ohcix_pdata,
},
.num_resources = ARRAY_SIZE(ohci0_resources),
.resource = ohci0_resources,
};
static struct resource ohci1_resources[] = {
[0] = {
.start = 0xfff70400,
.end = 0xfff70800 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = gic_spi(45),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device ohci1_device = {
.name = "ohci-platform",
.id = 1,
.dev = {
.dma_mask = &ohci1_device.dev.coherent_dma_mask,
.coherent_dma_mask = 0xffffffff,
.platform_data = &ohcix_pdata,
},
.num_resources = ARRAY_SIZE(ohci1_resources),
.resource = ohci1_resources,
};
static struct platform_device *marzen_late_devices[] __initdata = {
&ehci0_device,
&ehci1_device,
&ohci0_device,
&ohci1_device,
};
void __init marzen_init_late(void)
{
/* get usb phy */
phy = usb_get_phy(USB_PHY_TYPE_USB2);
shmobile_init_late();
platform_add_devices(marzen_late_devices,
ARRAY_SIZE(marzen_late_devices));
}
static void __init marzen_init(void) static void __init marzen_init(void)
{ {
regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers, regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
...@@ -188,6 +364,14 @@ static void __init marzen_init(void) ...@@ -188,6 +364,14 @@ static void __init marzen_init(void)
gpio_request(GPIO_FN_HSPI_TX0, NULL); gpio_request(GPIO_FN_HSPI_TX0, NULL);
gpio_request(GPIO_FN_HSPI_RX0, NULL); gpio_request(GPIO_FN_HSPI_RX0, NULL);
/* USB (CN21) */
gpio_request(GPIO_FN_USB_OVC0, NULL);
gpio_request(GPIO_FN_USB_OVC1, NULL);
gpio_request(GPIO_FN_USB_OVC2, NULL);
/* USB (CN22) */
gpio_request(GPIO_FN_USB_PENC2, NULL);
r8a7779_add_standard_devices(); r8a7779_add_standard_devices();
platform_add_devices(marzen_devices, ARRAY_SIZE(marzen_devices)); platform_add_devices(marzen_devices, ARRAY_SIZE(marzen_devices));
} }
...@@ -200,6 +384,6 @@ MACHINE_START(MARZEN, "marzen") ...@@ -200,6 +384,6 @@ MACHINE_START(MARZEN, "marzen")
.init_irq = r8a7779_init_irq, .init_irq = r8a7779_init_irq,
.handle_irq = gic_handle_irq, .handle_irq = gic_handle_irq,
.init_machine = marzen_init, .init_machine = marzen_init,
.init_late = shmobile_init_late, .init_late = marzen_init_late,
.timer = &shmobile_timer, .timer = &shmobile_timer,
MACHINE_END MACHINE_END
...@@ -26,6 +26,7 @@ ...@@ -26,6 +26,7 @@
* A: inversion * A: inversion
* B: format mode * B: format mode
* C: chip specific * C: chip specific
* D: clock selecter if master mode
*/ */
/* A: clock inversion */ /* A: clock inversion */
...@@ -44,6 +45,11 @@ ...@@ -44,6 +45,11 @@
#define SH_FSI_OPTION_MASK 0x00000F00 #define SH_FSI_OPTION_MASK 0x00000F00
#define SH_FSI_ENABLE_STREAM_MODE (1 << 8) /* for 16bit data */ #define SH_FSI_ENABLE_STREAM_MODE (1 << 8) /* for 16bit data */
/* D: clock selecter if master mode */
#define SH_FSI_CLK_MASK 0x0000F000
#define SH_FSI_CLK_EXTERNAL (1 << 12)
#define SH_FSI_CLK_CPG (2 << 12) /* FSIxCK + FSI-DIV */
/* /*
* set_rate return value * set_rate return value
* *
......
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment