Show the error code returned from the USB subsystem in
the debug messages.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a module param to disable auto clock selection.
This is provided for users that expect the audio stream to
fail when the clock source is invalid (e.g., the word clock
was unintentionally disconnected).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If a selector is available on a device, it may be pointing to a
clock source which is currently invalid.
If there is a valid clock source which can be selected, switch
to it.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Move the check that parse_audio_format_rates_v2() do after
receiving the clock source entity ID directly into the find
function and add a validation flag to the function.

This patch does not introduce any logic flow change.

It is provided to allow introducing automatic clock switching
easier later. By moving this uac_clock_source_is_valid callsite,
2 additional callsites can be avoided.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Replace the endianness conversions with the kernel-wide swabbing macros
in get/set_sample_rate_v2.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Correct spelling of snd_usb_endpoint_implict_feedback_sink in all
occurances.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Put EXPORT_SYMBOLS directly under the exported function.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Minor style fix, following a general code style in the kernel.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Change occurances of list_for_each into list_for_each_entry where
applicable.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just for cleaning up, introduce a new function get_sample_rate_v2()
for replacing two identical calls in set_sample_rate_v2().

No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Back-merge for cleaning up usb-audio code the recent commit modified,
and further UAC2 autoclock patches.

The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.

Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.

The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.

Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch let ELD debug message show 'pin_eld->monitor_present' which reflects
the real pin response to verb GET_PIN_SENSE.

'eld->monitor_present' should not be used here because 'eld' is a temp
structure now and so its "monitor_present" is not set.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In function snd_hdmi_get_eld(), the variable 'ret' should be initialized to 0.
Otherwise it will be returned uninitialized as non-zero after ELD info is got
successfully. Thus hdmi_present_sense() will always assume ELD info is invalid
by mistake, and /proc file system cannot show the proper ELD info.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: stable@vger.kernel.org
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-fix-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v3.9

A few more fixes here and there, including quite a few nasty driver
specific ones, but nothing that has a major general impact.

Turing on the headphone amp interferes with the impedance measurement
used to detect a TRRS style headset microphone.  Delay the HP turn on
until 500ms after the jack is detected, allowing the mic detection
state machine to run to completion.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Used kmemdup instead of replicating it's behaviour with kmalloc followed
by memcpy.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Used kmemdup instead of replicating it's behaviour with kmalloc followed
by memcpy.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull SCSI target fixes from Nicholas Bellinger:
 "These are mostly minor fixes this time around.  The iscsi-target CHAP
  big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
  1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
  stable.

  Also, there is a persistent reservations regression that has recently
  been reported for >= v3.8.x code, that is currently being tracked down
  for v3.9."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target/pscsi: Reject cross page boundary case in pscsi_map_sg
  target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
  tcm_vhost: Flush vhost_work in vhost_scsi_flush()
  tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
  target: fix possible memory leak in core_tpg_register()
  target/iscsi: Fix mutual CHAP auth on big-endian arches
  target_core_sbc: use noop for SYNCHRONIZE_CACHE

Pull md fixes from NeilBrown:
 "A few bugfixes for md

   - recent regressions in raid5
   - recent regressions in dmraid
   - a few instances of CONFIG_MULTICORE_RAID456 linger

  Several tagged for -stable"

* tag 'md-3.9-fixes' of git://neil.brown.name/md:
  md: remove CONFIG_MULTICORE_RAID456 entirely
  md/raid5: ensure sync and DISCARD don't happen at the same time.
  MD: Prevent sysfs operations on uninitialized kobjects
  MD RAID5: Avoid accessing gendisk or queue structs when not available
  md/raid5: schedule_construction should abort if nothing to do.

Pull libata updates from Jeff Garzik:
 "Simple stuff.  See one-line summaries."

* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  pata_samsung_cf: use module_platform_driver_probe()
  [libata] Avoid specialized TLA's in ZPODD's Kconfig
  libata-acpi.c: fix copy and paste mistake in ata_acpi_register_power_resource
  sata_fsl: Remove redundant NULL check before kfree
  ahci: Add Device IDs for Intel Wellsburg PCH
  ata_piix: Add MODULE_PARM_DESC to prefer_ms_hyperv

Pull i2c fixes from Wolfram Sang:
 "One bugfix for the tegra driver.  Two updates regarding email
  addresses and MAINTAINERS which I like to have up-to-date so people
  can be reached immediately.  While we are here, there is on PCI_ID
  addition."

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: add maintainer entry for atmel i2c driver
  i2c: Fix my e-mail address in drivers and documentation
  i2c: iSMT: add Intel Avoton DeviceIDs
  i2c: tegra: check the clk_prepare_enable() return value

Pull watchdog fixes from Wim Van Sebroeck:
 "Fix a boot issues and correct the AcpiMmioSel bitmask in the
  sp5100_tco watchdog device driver"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
  watchdog: sp5100_tco: Remove code that may cause a boot failure

When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed.  Consecutive (debug-) output of that mode thus yields 0 for
vsync.  This simple fix also speeds up future invocations of
drm_mode_vrefresh().

While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.

Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these.  The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.

See

   http://en.wikipedia.org/wiki/EDID

and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.

Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NVMe driver update from Matthew Wilcox:
 "These patches have mostly been baking for a few months; sorry I didn't
  get them in during the merge window.  They're all bug fixes, except
  for the addition of the SMART log and the addition to MAINTAINERS."

* git://git.infradead.org/users/willy/linux-nvme:
  NVMe: Add namespaces with no LBA range feature
  MAINTAINERS: Add entry for the NVMe driver
  NVMe: Initialize iod nents to 0
  NVMe: Define SMART log
  NVMe: Add result to nvme_get_features
  NVMe: Set result from user admin command
  NVMe: End queued bio requests when freeing queue
  NVMe: Free cmdid on nvme_submit_bio error

Merge misc fixes from Andrew Morton.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
  mm/hotplug: only free wait_table if it's allocated by vmalloc
  dma-debug: update DMA debug API to better handle multiple mappings of a buffer
  dma-debug: fix locking bug in check_unmap()
  drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
  drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
  drivers/rtc/rtc-da9052.c: fix for rtc device registration
  mm: zone_end_pfn is too small
  poweroff: change orderly_poweroff() to use schedule_work()
  mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
  printk: Provide a wake_up_klogd() off-case
  irq_work.h: fix warning when CONFIG_IRQ_WORK=n

mnt_drop_write() must be called only if mnt_want_write() succeeded,
otherwise the mnt_writers counter will diverge.

mnt_writers counters are used to check if remounting FS as read-only is
OK, so after an extra mnt_drop_write() call, it would be impossible to
remount mqueue FS as read-only.  Besides, on umount a warning would be
printed like this one:

  =====================================
  [ BUG: bad unlock balance detected! ]
  3.9.0-rc3 #5 Not tainted
  -------------------------------------
  a.out/12486 is trying to release lock (sb_writers) at:
  mnt_drop_write+0x1f/0x30
  but there are no more locks to release!
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zone->wait_table may be allocated from bootmem, it can not be freed.
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Reviewed-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There were reports of the igb driver unmapping buffers without calling
dma_mapping_error.  On closer inspection issues were found in the DMA
debug API and how it handled multiple mappings of the same buffer.

The issue I found is the fact that the debug_dma_mapping_error would
only set the map_err_type to MAP_ERR_CHECKED in the case that the was
only one match for device and device address.  However in the case of
non-IOMMU, multiple addresses existed and as a result it was not setting
this field once a second mapping was instantiated.  I have resolved this
by changing the search so that it instead will now set MAP_ERR_CHECKED
on the first buffer that matches the device and DMA address that is
currently in the state MAP_ERR_NOT_CHECKED.

A secondary side effect of this patch is that in the case of multiple
buffers using the same address only the last mapping will have a valid
map_err_type.  The previous mappings will all end up with map_err_type
set to MAP_ERR_CHECKED because of the dma_mapping_error call in
debug_dma_map_page.  However this behavior may be preferable as it means
you will likely only see one real error per multi-mapped buffer, versus
the current behavior of multiple false errors mer multi-mapped buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In check_unmap() it is possible to get into a dead-locked state if
dma_mapping_error is called.  The problem is that the bucket is locked in
check_unmap, and locked again by debug_dma_mapping_error which is called
by dma_mapping_error.  To resolve that we must release the lock on the
bucket before making the call to dma_mapping_error.

[akpm@linux-foundation.org: restore 80-col trickery to be consistent with the rest of the file]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>