- 28 Jun, 2016 8 commits
-
-
Giuseppe CAVALLARO authored
In case of SGMII more, for example when a MAC2MAC connection is needed, the port selection bits (inside the MAC configuration registers) have to be programmed according to the link selected. So the patch adds a new DT parameter to pass the port selection and to programmed related PCS and CORE to use it. Signed-off-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Giuseppe CAVALLARO authored
By default, all gmac cores disable the PCS block and always enable the PMT. Note that this is done in a different way by 3.x and 4.x cores. With this rework, PCS and PMT interrupt masks can be driven by parameters now moved inside the mac_device_info structure and the settings follow what the HW capability register reports. Signed-off-by:
-
Giuseppe CAVALLARO authored
The 3.xx and 4.xx synopsys gmacs have a very similar PCS embedded module and they share almost the same registers: for example: AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability, AN_Expansion, TBI_Extended_Status. Just the RGMII/SMII Control/Status register differs. So This patch aims to reorganize and enhance the PCS support. It removes the existent support from the dwmac1000/dwmac4_core.c moving basic PCS functions inside a new file called: stmmac_pcs.h. The patch also reviews the available APIs to be better shared among different hardware and easily enhanced to support new features. Signed-off-by:
-
Arnd Bergmann authored
Calling the fixed-phy functions when CONFIG_FIXED_PHY=m as a previous change tried cannot work if the caller is in built-in code: drivers/of/built-in.o: In function `of_phy_register_fixed_link': of_reserved_mem.c:(.text+0x85e0): undefined reference to `fixed_phy_register' Making of_mdio depend on 'FIXED_PHY || !FIXED_PHY' would solve this dependency by enforcing that OF_MDIO itself becomes a loadable module when FIXED_PHY=y, but that creates a different dependency as it breaks any built-in ethernet driver that uses of_mdio. Making FIXED_PHY a bool option also cannot work, since it depends on PHYLIB, which again is tristate. This version now uses 'select FIXED_PHY' to ensure that the fixed-phy portion of of_mdio is not optional. The main downside of this is a small increase in code size for cases that do not need fixed phy support, but it should avoid all of the link-time problems. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: d1bd330a ("of_mdio: Enable fixed PHY support if driver is a module") Acked-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Amitoj Kaur Chawla authored
Drop redundant include of moduleparam.h The Coccinelle semantic patch used to make this change is as follows: @ includesmodule @ @@ #include <linux/module.h> @ depends on includesmodule @ @@ - #include <linux/moduleparam.h> Signed-off-by:
Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by:
-
David Ahern authored
Add support to inet_diag facility to filter sockets based on device index. If an interface index is in the filter only sockets bound to that index (sk_bound_dev_if) are returned. Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Philippe Reynes authored
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by:Philippe Reynes <tremyfr@gmail.com> Signed-off-by:
-
Philippe Reynes authored
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by:
-
- 27 Jun, 2016 30 commits
-
-
David S. Miller authored
Russell King says: ==================== Initial SFP support patches Please review and merge this initial patch set, which is part of a larger set previously posted adding SFP support to phy and mvneta. This initial set are focused on cleaning up and reorganising the fixed-phy code to allow the core software-phy code to be re-used. These are based on net-next. ==================== Signed-off-by: -
Russell King authored
There is no prevention of a concurrent call to both fixed_mdio_read() and fixed_phy_update_state(), which can result in the state being modified while it's being inspected. Fix this by using a seqcount to detect modifications, and memcpy()ing the state. We remain slightly naughty here, calling link_update() and updating the link status within the read-side loop - which would need rework of the design to change. Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Russell King authored
Generate software phy registers as and when requested, rather than duplicating the state in fixed_phy. This allows us to eliminate the duplicate storage of of the same data, which is only different in format. As fixed_phy_update_regs() no longer updates register state, rename it to fixed_phy_update(). Reviewed-by:
-
Russell King authored
Separate out the generation of MII registers from the state validation. This allows us to simplify the error handing in fixed_phy() by allowing earlier error detection. Reviewed-by:
-
Russell King authored
Convert the swphy register generation to tabular form which allows us to eliminate multiple switch() statements. This results in a smaller object code size, more efficient, and easier to add support for faster speeds. Before: Idx Name Size VMA LMA File off Algn 0 .text 00000164 00000000 00000000 00000034 2**2 text data bss dec hex filename 388 0 0 388 184 swphy.o After: Idx Name Size VMA LMA File off Algn 0 .text 000000fc 00000000 00000000 00000034 2**2 5 .rodata 00000028 00000000 00000000 00000138 2**2 text data bss dec hex filename 324 0 0 324 144 swphy.o Reviewed-by: -
Russell King authored
Move the fixed_phy MII register generation to a library to allow other software phy implementations to use this code. Reviewed-by:
-
David S. Miller authored
Merge tag 'linux-can-next-for-4.8-20160623' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2016-06-17 this is a pull request of 4 patches for net-next/master. Arnd Bergmann's patch fixes a regresseion in af_can introduced in linux-can-next-for-4.8-20160617. There are two patches by Ramesh Shanmugasundaram, which add CAN-2.0 support to the rcar_canfd driver. And a patch by Ed Spiridonov that adds better error diagnoses messages to the Ed Spiridonov driver. ==================== Signed-off-by:
-
Amitoj Kaur Chawla authored
Replace calls to kmalloc followed by a memcpy with a direct call to kmemdup. The Coccinelle semantic patch used to make this change is as follows: @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Colin Ian King authored
trivial fixes to spelling mistakes of the words "excessive collisions" Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Colin Ian King authored
trivial fixes to spelling mistakes of the word "descriptors" Signed-off-by:
-
David S. Miller authored
Saeed Mahameed says: ==================== Mellanox 100G mlx5e Ethernet extensions This series includes multiple features extensions for mlx5 Ethernet netdevice driver. Namely, TX Rate limiting, RX interrupt moderation, ethtool settings. TX Rate limiting: - ConnectX-4 rate limiting infrastructure - Set max rate NDO support RX interrupt moderation: - CQE based coalescing option (controlled via priv flags) - Adaptive RX coalescing ethtool settings: - priv flags callbacks - Support new ksettings API - Add 50G missing link mode - Support auto negotiation on/off Applied on top: 0e9390eb ("Merge branch 'mlxsw-next'") ==================== Signed-off-by:
-
Gal Pressman authored
Previous to this patch auto negotiation was reported off although it was on by default in hardware. This patch reports the correct information to ethtool and allows the user to toggle it on/off. Added another parameter to set port proto function in order to pass the auto negotiation field to the hardware. Signed-off-by:
Gal Pressman <galp@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Gal Pressman authored
Use new get/set link ksettings and remove get/set settings legacy callbacks. This allows us to use bitmasks longer than 32 bit for supported and advertised link modes and use modes that were previously not supported. Signed-off-by:
-
Gal Pressman authored
Add MLX5E_50GBASE_SR2 as ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT. Signed-off-by:
-
Gal Pressman authored
Add ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT bit. Signed-off-by:
David Decotigny <decot@googlers.com> Signed-off-by:
-
Gal Pressman authored
Add a dedicated function to toggle port link. It should be called only after setting a port register. Toggle will set port link to down and bring it back up in case that it's admin status was up. Signed-off-by:
-
Gil Rockah authored
Striving for high message rate and low interrupt rate. Usage: ethtool -C <interface> adaptive-rx on/off Signed-off-by:Gil Rockah <gilr@mellanox.com> Signed-off-by:
Achiad Shochat <achiad@mellanox.com> Signed-off-by:
-
Tariq Toukan authored
In this mode the moderation timer will restart upon new completion (CQE) generation rather than upon interrupt generation. The outcome is that for bursty traffic the period timer will never expire and thus only the moderation frames counter will dictate interrupt generation, thus the interrupt rate will be relative to the incoming packets size. If the burst seizes for "moderation period" time then an interrupt will be issued immediately. CQE based moderation is off by default and can be controlled via ethtool set_priv_flags. Performance tested on ConnectX4-Lx 50G. Less packet loss in netperf UDP and TCP tests, with no bw degradation, for both single and multi streams, with message sizes of 64, 1024, 1472 and 32768 byte. Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Gal Pressman authored
Introduce an infrastructure for getting/setting private net device flags. Currently a 'nop' priv flag is added, following patches will override the flag will actual feature specific flags. Signed-off-by:
-
Yevgeny Petrilin authored
Implement set_maxrate ndo. Use the rate index from the hardware table to attach to channel SQ/TXQ. In case of failure to configure new rate, the queue remains with unlimited rate. We save the configuration on priv structure and apply it each time Send Queues are being reinitialized (after open/close) operations. Signed-off-by:
Yevgeny Petrilin <yevgenyp@mellanox.com> Signed-off-by:
-
Yevgeny Petrilin authored
Configuring and managing HW rate limit tables. The HW holds a table of rate limits, each rate is associated with an index in that table. Later a Send Queue uses this index to set the rate limit. Multiple Send Queues can have the same rate limit, which is represented by a single entry in this table. Even though a rate can be shared, each queue is being rate limited independently of others. The SW shadow of this table holds the rate itself, the index in the HW table and the refcount (number of queues) working with this rate. The exported functions are mlx5_rl_add_rate and mlx5_rl_remove_rate. Number of different rates and their values are derived from HW capabilities. Signed-off-by:
-
David S. Miller authored
Sathya Perla says: ==================== be2net: patch set Hi Dave, pls consider commiting the following patches to the net-next tree. Thanks! Patch 1 replaces the be_max_eqs() macro with two new macros called be_max_nic_eqs() and be_max_func_eqs() to clear confusion in that part of the code. Patch 2 adds support to configure asymmetric number of rx/tx queues via ethtool set-channels option. Patch 3 disables EVB when VFs are not enabled on a BE3 SR-IOV config to avoid the broadcast echo problem. Patch 4 updates copyright markings in be2net src files Patch 5 updates the be2net maintainers' list ==================== Signed-off-by: -
Sathya Perla authored
This patch removes Padmanabh's name from the maintainers list as he's no longer with the company. It also adds the driver name on the headline to make it easy to lookup the maintainers list by the driver name. Signed-off-by:
Sathya Perla <sathya.perla@broadcom.com> Signed-off-by:
-
Somnath Kotur authored
This patch updates year and company name in the copyright markings in the be2net source files. Signed-off-by:
Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by:
-
Somnath Kotur authored
On SR-IOV profiles, when the user connects a Linux Bridge or OVS to a BE3 vport, they suffer the "broadcast/multicast echo" problem. BE3 EVB echoes broadcast and multicast packets back to PF's vport confusing the Linux bridge. BE3 relies on the src-mac addr being programmed on the interface to avoid sending back an echo of a broadcast or multicast packet on a vPort. When a Linux bridge is connected to a BE3, the mac-addr of the VM behind the bridge doesn't get configured on the vPort and so echo cancellation doesn't work. This patch worksaround this problem by disabling the EVB initially and re-enabling it *only* when SR-IOV is enabled by the user. For the driver fix to work, the BE3 FW version must be >= 11.1.84.0. Signed-off-by:
-
Sathya Perla authored
be2net so far supported creation of RX/TX queues only in pairs. On configs where rx and tx queue counts are different, creation of only the lesser number of queues has been supported. This patch now allows a combination of RX/TX-only channels along with combined channels. N TX-queues and M RX-queues can be created with the following cmds: ethtool -L ethX combined N rx M-N (when N < M) ethtool -L ethX combined M tx N-M (when M < N) Setting both RX-only and TX-only channels is still not supported. It is mandatory to create atleast one combined channel. Signed-off-by:
-
Sathya Perla authored
The EQs available on a function are shared between NIC and RoCE. The be_max_eqs() macro was so far being used to refer to the max number of EQs available for NIC. This has caused some confusion in the code. To fix this confusion this patch introduces a new macro called be_max_nic_eqs() to refer to the max number of EQs avialable for NIC only and renames be_max_eqs() to be_max_func_eqs(). Signed-off-by:
-
David S. Miller authored
Andy Duan says: ==================== net: fec: add new type device Different i.MX SOC FEC support different features like : - i.MX6Q/DL FEC does not support AVB and interrupt coalesc - i.MX6SX/i.MX7D supports AVB and interrupt coalesc - i.MX6UL/ULL does not support AVB, but support interrupt coalesc Then, add new quirk flag to judge the supported features, and add new type device for i.MX6UL. ==================== Signed-off-by: -
Fugang Duan authored
i.MX6UL is a member in i.MX series family, the SOC FEC inherits from i.MX6SX but removes some IP features, lets define a new type for fec device. Signed-off-by:
Fugang Duan <fugang.duan@nxp.com> Signed-off-by:
-
Fugang Duan authored
Different i.MX SOC FEC support different features like : - i.MX6Q/DL FEC does not support AVB and interrupt coalesc - i.MX6SX/i.MX7D supports AVB and interrupt coalesc - i.MX6UL/ULL does not support AVB, but support interrupt coalesc So, add new quirk flag to judge the supported features. Signed-off-by:
-
- 26 Jun, 2016 2 commits
-
-
David S. Miller authored
Merge tag 'rxrpc-rewrite-20160622-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs David Howells says: ==================== rxrpc: Get rid of conn bundle and transport structs Here's the next part of the AF_RXRPC rewrite. The primary purpose of this set is to get rid of the rxrpc_conn_bundle and rxrpc_transport structs. This simplifies things for future development of the connection handling. To this end, the following significant changes are made: (1) The rxrpc_connection struct is given pointers to the local and peer endpoints, inside the rxrpc_conn_parameters struct. Pointers to the transport's copy of these pointers are then redirected to the connection struct. (2) Exclusive connection handling is fixed. Exclusive connections should do just one call and then be retired. They are used in security negotiations and, I believe, the idea is to avoid reuse of negotiated security contexts. The current code is doing a single connection per socket and doing all the calls over that. With this change it gets a new connection for each call made. (3) A new sendmsg() control message marker is added to make individual calls operate over exclusive connections. This should be used in future in preference to the sockopt that marks a socket as "exclusive connection". (4) IDs for client connections initiated by a machine are now allocated from a global pool using the IDR facility and are unique across all client connections, no matter their destination. The IDR facility is then used to look up a connection on the connection ID alone. Other parameters are then verified afterwards. Note that the IDR facility may use a lot of memory if the IDs it holds are widely scattered. Given this, in a future commit, client connections will be retired if they are more than a certain distance from the last ID allocated. The client epoch is advanced by 1 each time the client ID counter wraps. Connections outside the current epoch will also be retired in a future commit. (5) The connection bundle concept is removed and the client connection tree is moved into the local endpoint. The queue for waiting for a call channel is moved to the rxrpc_connection struct as there can only be one connection for any particular key going to any particular peer now. (6) The rxrpc_transport struct is removed and the service connection tree is moved into the peer struct. ==================== Signed-off-by:
-
Xing Zheng authored
Add constants and callback functions for the dwmac on rk3228/rk3229 socs. As can be seen, the base structure is the same, only registers and the bits in them moved slightly. Signed-off-by:
Xing Zheng <zhengxing@rock-chips.com> Reviewed-by:
Heiko Stuebner <heiko@sntech.de> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
