While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.

Fixes: 7acc9973 ("usb: phy: generic: add vbus support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220425171412.1188485-3-sean.anderson@seco.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.

Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.

Fixes: 6d8a0196 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds the necessary PCI IDs for Intel Meteor Lake-P
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220425103518.44028-1-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-5.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for 5.18-rc4

Here's a fix for a potential overflow issue in the whiteheat driver when
using the old ARM ABI.

Included are also some new modem device ids.

All have been in linux-next with no reported issues.

* tag 'usb-serial-5.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: whiteheat: fix heap overflow in WHITEHEAT_GET_DTR_RTS
  USB: serial: cp210x: add PIDs for Kamstrup USB Meter Reader
  USB: serial: option: add support for Cinterion MV32-WA/MV32-WB
  USB: serial: option: add Telit 0x1057, 0x1058, 0x1075 compositions

Make sure not to set run_stop bit or link state change request while
initiating soft-reset. Register read-modify-write operation may
unintentionally start the controller before the initialization completes
with its previous DCTL value, which can cause initialization failure.

Fixes: f59dcab1 ("usb: dwc3: core: improve reset sequence")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6aecbd78328f102003d40ccf18ceeebd411d3703.1650594792.git.Thinh.Nguyen@synopsys.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If any function like UVC is deactivating gadget as part of composition
switch which results in not calling pullup enablement, it is not getting
enabled after switch to new composition due to this deactivation flag
not cleared. This results in USB enumeration not happening after switch
to new USB composition. Hence clear deactivation flag inside gadget
structure in configfs_composite_unbind() before switch to new USB
composition.
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220413211038.72797-1-w36195@motorola.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is odd to call devm_add_action_or_reset() before calling the function
that should be undone.

Either, the "_or_reset" part should be omitted, or the action should be
recorded after the resources have been allocated.

Switch the order of devm_add_action_or_reset() and usb_role_switch_get().

Fixes: 9a1bf58c ("usb: misc: eud: Add driver support for Embedded USB Debugger(EUD)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/362908699275ecec078381b42d87c817c6965fc6.1648979948.git.christophe.jaillet@wanadoo.frSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit ae8709b2 ("USB: core: Make do_proc_control() and
do_proc_bulk() killable") if a device has the USB_QUIRK_DELAY_CTRL_MSG
quirk set, it will temporarily block all other URBs (e.g. interrupts)
while sleeping due to a control.

This results in noticeable delays when, for example, a userspace usbfs
application is sending URB interrupts at a high rate to a keyboard and
simultaneously updates the lock indicators using controls. Interrupts
with direction set to IN are also affected by this, meaning that
delivery of HID reports (containing scancodes) to the usbfs application
is delayed as well.

This patch fixes the regression by calling msleep() while the device
mutex is unlocked, as was the case originally with usb_control_msg().

Fixes: ae8709b2 ("USB: core: Make do_proc_control() and do_proc_bulk() killable")
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Link: https://lore.kernel.org/r/3e299e2a-13b9-ddff-7fee-6845e868bc06@tasossah.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the PHY controller node has a "port" dwc3 tries to find an
extcon device even when "usb-role-switch" is present. This happens
because dwc3_get_extcon() sees that "port" node and then calls
extcon_find_edev_by_node() which will always return EPROBE_DEFER
in that case.

On the other hand, even if an extcon was present and dwc3_get_extcon()
was successful it would still be ignored in favor of "usb-role-switch".

Let's just first check if "usb-role-switch" is configured in the device
tree and directly use it instead and only try to look for an extcon
device otherwise.

Fixes: 8a0a1379 ("usb: dwc3: Registering a role switch in the DRD code.")
Cc: stable <stable@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20220411155300.9766-1-sven@svenpeter.devSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current driver logic checks against 0 to determine whether the
periodic tx/rx threshold settings are set, but we may get bogus values
from uninitialized variables if no device property is set. Properly
default these variables to 0.

Fixes: 938a5ad1 ("usb: dwc3: Check for ESS TX/RX threshold config")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cccfce990b11b730b0dae42f9d217dc6fb988c90.1649727139.git.Thinh.Nguyen@synopsys.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Issue description:
  When an OTG port has been switched to device role and then switch back
  to host role again, the USB 3.0 Host (XHCI) will not be able to detect
  "plug in event of a connected USB 2.0/1.0 ((Highspeed and Fullspeed)
  devices until system reboot.

Root cause and Solution:
  There is a condition checking flag "ssusb->otg_switch.is_u3_drd" in
  toggle_opstate(). At the end of role switch procedure, toggle_opstate()
  will be called to set DC_SESSION and SOFT_CONN bit. If "is_u3_drd" was
  set and switched the role to USB host 3.0, bit DC_SESSION and SOFT_CONN
  will be skipped hence caused the port cannot detect connected USB 2.0
  (Highspeed and Fullspeed) devices. Simply remove the condition check to
  solve this issue.

Fixes: d0ed062a ("usb: mtu3: dual-role mode support")
Cc: stable@vger.kernel.org
Tested-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Tainping Fang <tianping.fang@mediatek.com>
Link: https://lore.kernel.org/r/20220419081245.21015-1-macpaul.lin@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Alderlake has two XHCI controllers with PCI IDs 0x461e and 0x51ed. We
had previously added the quirk to default enable runtime PM for 0x461e,
now add it for 0x51ed as well.
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220408114225.1.Ibcff6b86ed4eacfe4c4bc89c90e18416f3900a3e@changeidSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 33fb697e ("usb: dwc3: Get clocks individually") moved from
the clk_bulk api to individual clocks, following the snps,dwc3.yaml
dt-binding for clock names.
Unfortunately the rk3328 (and upcoming rk356x support) use the
rockchip,dwc3.yaml which has different clock names, which are common on
devices using the glue layer.
The rk3328 does not use a glue layer, but attaches directly to the dwc3
core driver.
The offending patch series failed to account for this, thus dwc3 was
broken on rk3328.

To retain backwards compatibility with rk3328 device trees we must also
check for the alternate clock names.

Fixes: 33fb697e ("usb: dwc3: Get clocks individually")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220409152116.3834354-1-pgwipeout@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"reg" property is required on Samsung S5PV210/Exynos EHCI/OHCI
controllers.

Fixes: 4bf2283c ("dt-bindings: usb: samsung,exynos-usb2: convert to dtschema")
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220407192338.14849-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_put_dev shouldn't be called when uss720_probe succeeds because of
priv->usbdev. At the same time, priv->usbdev shouldn't be set to NULL
before destroy_priv in uss720_disconnect because usb_put_dev is in
destroy_priv.

Fix this by moving priv->usbdev = NULL after usb_put_dev.

Fixes: dcb4b8ad ("misc/uss720: fix memory leak in uss720_probe")
Cc: stable <stable@kernel.org>
Reviewed-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220407024001.11761-1-hbh25y@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In zhaoxin platform, some ehci projects will latch a wakeup signal
internal when plug in a device on port during system S0. This wakeup
signal will turn on when ehci runtime suspend, which will trigger a
system control interrupt that will resume ehci back to D0. As no
device connect, ehci will be set to runtime suspend and turn on the
internal latched wakeup signal again. It will cause a suspend-resume
loop and generate system control interrupt continuously.

Fixed this issue by clear wakeup signal latched in ehci internal when
ehci resume callback is called.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20220324121735.3803-1-WeitaoWang-oc@zhaoxin.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix:

  drivers/usb/typec/tcpm/tcpm.c: In function ‘run_state_machine’:
  drivers/usb/typec/tcpm/tcpm.c:4724:3: error: case label does not reduce to an integer constant
     case BDO_MODE_TESTDATA:
     ^~~~

See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20220405151517.29753-8-bp@alien8.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Building without CONFIG_POWER_SUPPLY will fail:

drivers/usb/typec/rt1719.o: In function `rt1719_psy_set_property':
rt1719.c:(.text+0x10a): undefined reference to `power_supply_get_drvdata'
drivers/usb/typec/rt1719.o: In function `rt1719_psy_get_property':
rt1719.c:(.text+0x2c8): undefined reference to `power_supply_get_drvdata'
drivers/usb/typec/rt1719.o: In function `devm_rt1719_psy_register':
rt1719.c:(.text+0x3e9): undefined reference to `devm_power_supply_register'
drivers/usb/typec/rt1719.o: In function `rt1719_irq_handler':
rt1719.c:(.text+0xf9f): undefined reference to `power_supply_changed'
drivers/usb/typec/rt1719.o: In function `rt1719_update_pwr_opmode.part.9':
rt1719.c:(.text+0x657): undefined reference to `power_supply_changed'
drivers/usb/typec/rt1719.o: In function `rt1719_attach':
rt1719.c:(.text+0x83e): undefined reference to `power_supply_changed'

Add POWER_SUPPLY dependency to Kconfig.

Fixes: 25d29b98 ("usb: typec: rt1719: Add support for Richtek RT1719")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Link: https://lore.kernel.org/r/20220418082425.41566-1-renzhijie2@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All attempts to swap the roles timed out because the
completion was done without releasing the port lock. Fixing
that by releasing the lock before starting to wait for the
completion.

Link: https://lore.kernel.org/linux-usb/037de7ac-e210-bdf5-ec7a-8c0c88a0be20@gmail.com/
Fixes: ad74b864 ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220405134824.68067-3-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The role swapping completion variable is reused, so it needs
to be reinitialised every time. Otherwise it will be marked
as done after the first time it's used and completing
immediately.

Link: https://lore.kernel.org/linux-usb/20220325203959.GA19752@jackp-linux.qualcomm.com/
Fixes: 6df475f8 ("usb: typec: ucsi: Start using struct typec_operations")
Cc: stable@vger.kernel.org
Reported-and-suggested-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220405134824.68067-2-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.

Fixes: 41a7426d ("usb: xhci: tegra: Unlink power domain devices")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220319023822.145641-1-zhangqilong3@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The sizeof(struct whitehat_dr_info) can be 4 bytes under CONFIG_AEABI=n
due to "-mabi=apcs-gnu", even though it has a single u8:

whiteheat_private {
        __u8                       mcr;                  /*     0     1 */

        /* size: 4, cachelines: 1, members: 1 */
        /* padding: 3 */
        /* last cacheline: 4 bytes */
};

The result is technically harmless, as both the source and the
destinations are currently the same allocation size (4 bytes) and don't
use their padding, but if anything were to ever be added after the
"mcr" member in "struct whiteheat_private", it would be overwritten. The
structs both have a single u8 "mcr" member, but are 4 bytes in padded
size. The memcpy() destination was explicitly targeting the u8 member
(size 1) with the length of the whole structure (size 4), triggering
the memcpy buffer overflow warning:

In file included from include/linux/string.h:253,
                 from include/linux/bitmap.h:11,
                 from include/linux/cpumask.h:12,
                 from include/linux/smp.h:13,
                 from include/linux/lockdep.h:14,
                 from include/linux/spinlock.h:62,
                 from include/linux/mmzone.h:8,
                 from include/linux/gfp.h:6,
                 from include/linux/slab.h:15,
                 from drivers/usb/serial/whiteheat.c:17:
In function 'fortify_memcpy_chk',
    inlined from 'firm_send_command' at drivers/usb/serial/whiteheat.c:587:4:
include/linux/fortify-string.h:328:25: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
  328 |                         __write_overflow_field(p_size_field, size);
      |                         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Instead, just assign the one byte directly.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202204142318.vDqjjSFn-lkp@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220421001234.2421107-1-keescook@chromium.orgSigned-off-by: Johan Hovold <johan@kernel.org>

Wireless reading of water and heat meters using 868 MHz wM-Bus mode C1.

The two different product IDs allow detection of dongle antenna
solution:
- Internal antenna
- External antenna using SMA connector

https://www.kamstrup.com/en-en/water-solutions/water-meter-reading/usb-meter-readerSigned-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20220414081202.5591-1-bruno.thomsen@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

Add support for Cinterion device MV32-WA/MV32-WB. MV32-WA PID is
0x00F1, and MV32-WB PID is 0x00F2.

Test evidence as below:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  4 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=1e2d ProdID=00f1 Rev=05.04
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00F1 USB Mobile Broadband
S:  SerialNumber=78ada8c4
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option

T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  3 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=1e2d ProdID=00f2 Rev=05.04
S:  Manufacturer=Cinterion
S:  Product=Cinterion PID 0x00F2 USB Mobile Broadband
S:  SerialNumber=cdd06a78
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option

Interface 0&1: MBIM, 2:Modem, 3: GNSS, 4: NMEA, 5: Diag
GNSS port don't use serial driver.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20220414074434.5699-1-slark_xiao@163.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

During the uvcg_video_pump() process, if an error occurs and
uvcg_queue_cancel() is called, the buffer queue will be cleared out, but
the current marker (queue->buf_used) of the active buffer (no longer
active) is not reset. On the next iteration of uvcg_video_pump() the
stale buf_used count will be used and the logic of min((unsigned
int)len, buf->bytesused - queue->buf_used) may incorrectly calculate a
nbytes size, causing an invalid memory access.

[80802.185460][  T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
[80802.185519][  T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
...
uvcg_queue_cancel() is called and the queue is cleared out, but the
marker queue->buf_used is not reset.
...
[80802.262328][ T8682] Unable to handle kernel paging request at virtual
address ffffffc03af9f000
...
...
[80802.263138][ T8682] Call trace:
[80802.263146][ T8682]  __memcpy+0x12c/0x180
[80802.263155][ T8682]  uvcg_video_pump+0xcc/0x1e0
[80802.263165][ T8682]  process_one_work+0x2cc/0x568
[80802.263173][ T8682]  worker_thread+0x28c/0x518
[80802.263181][ T8682]  kthread+0x160/0x170
[80802.263188][ T8682]  ret_from_fork+0x10/0x18
[80802.263198][ T8682] Code: a8c12829 a88130cb a8c130

Fixes: d6925225 ("usb: gadget/uvc: Port UVC webcam gadget to use videobuf2 framework")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220331184024.23918-1-w36195@motorola.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This has been reported to stall if queried

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220414123152.1700-1-oneukum@suse.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This device is reported to stall when enummerated.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220414110209.30924-1-oneukum@suse.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the following Telit FN980 and FN990 compositions:

0x1057: tty, adb, rmnet, tty, tty, tty, tty, tty
0x1058: tty, adb, tty, tty, tty, tty, tty
0x1075: adb, tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20220406141408.580669-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

Path fixes bug which occurs during resetting endpoint in
__cdns3_gadget_ep_clear_halt function. During resetting endpoint
controller will change HW/DMA owned TRB. It set Abort flag in
trb->control and will change trb->length field. If driver want
to use the aborted trb it must update the changed field in
TRB.

Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220329084605.4022-1-pawell@cadence.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The first U3 wake signal by the host may be lost if the USB 3 connection is
tunneled over USB4, with a runtime suspended USB4 host, and firmware
implemented connection manager.

Specs state the host must wait 100ms (tU3WakeupRetryDelay) before
resending a U3 wake signal if device doesn't respond, leading to U3 -> U0
link transition times around 270ms in the tunneled case.

Fixes: 0200b9f7 ("xhci: Wait until link state trainsits to U0 after setting USB_SS_PORT_LS_U0")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-4-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.

Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.

[check shared hcd exist before stopping its roothub polling -Mathias]

Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-3-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In some situations software handles TRB events slower than adding TRBs.
If the number of TRB events to be processed in a given interrupt is exactly
the same as the event ring size 256, then the local variable
"event_ring_deq" that holds the initial dequeue position is equal to
software_dequeue after handling all 256 interrupts.

It will cause driver to not update ERDP to hardware,

Software dequeue pointer is out of sync with ERDP on interrupt exit.
On the next interrupt, the event ring may full but driver will not
update ERDP as software_dequeue is equal to ERDP.

[  536.377115] xhci_hcd 0000:00:12.0: ERROR unknown event type 37
[  566.933173] sd 8:0:0:0: [sdb] tag#27 uas_eh_abort_handler 0 uas-tag 7 inflight: CMD OUT
[  566.933181] sd 8:0:0:0: [sdb] tag#27 CDB: Write(10) 2a 00 17 71 e6 78 00 00 08 00
[  572.041186] xhci_hcd On some situataions,the0000:00:12.0: xHCI host not responding to stop endpoint command.
[  572.057193] xhci_hcd 0000:00:12.0: Host halt failed, -110
[  572.057196] xhci_hcd 0000:00:12.0: xHCI host controller not responding, assume dead
[  572.057236] sd 8:0:0:0: [sdb] tag#26 uas_eh_abort_handler 0 uas-tag 6 inflight: CMD
[  572.057240] sd 8:0:0:0: [sdb] tag#26 CDB: Write(10) 2a 00 38 eb cc d8 00 00 08 00
[  572.057244] sd 8:0:0:0: [sdb] tag#25 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD

Hardware ERDP is updated mid event handling if there are more than 128
events in an interrupt (half of ring size).
Fix this by updating the software local variable at the same time as
hardware ERDP.

[commit message rewording -Mathias]

Fixes: dc0ffbea ("usb: host: xhci: update event ring dequeue pointer on purpose")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-2-mathias.nyman@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull more tracing updates from Steven Rostedt:

 - Rename the staging files to give them some meaning. Just
   stage1,stag2,etc, does not show what they are for

 - Check for NULL from allocation in bootconfig

 - Hold event mutex for dyn_event call in user events

 - Mark user events to broken (to work on the API)

 - Remove eBPF updates from user events

 - Remove user events from uapi header to keep it from being installed.

 - Move ftrace_graph_is_dead() into inline as it is called from hot
   paths and also convert it into a static branch.

* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Move user_events.h temporarily out of include/uapi
  ftrace: Make ftrace_graph_is_dead() a static branch
  tracing: Set user_events to BROKEN
  tracing/user_events: Remove eBPF interfaces
  tracing/user_events: Hold event_mutex during dyn_event_add
  proc: bootconfig: Add null pointer check
  tracing: Rename the staging files for trace_events

Pull clk fix from Stephen Boyd:
 "A single revert to fix a boot regression seen when clk_put() started
  dropping rate range requests. It's best to keep various systems
  booting so we'll kick this out and try again next time"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  Revert "clk: Drop the rate range on clk_put()"

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 fixes and updates:

   - Make the prctl() for enabling dynamic XSTATE components correct so
     it adds the newly requested feature to the permission bitmap
     instead of overwriting it. Add a selftest which validates that.

   - Unroll string MMIO for encrypted SEV guests as the hypervisor
     cannot emulate it.

   - Handle supervisor states correctly in the FPU/XSTATE code so it
     takes the feature set of the fpstate buffer into account. The
     feature sets can differ between host and guest buffers. Guest
     buffers do not contain supervisor states. So far this was not an
     issue, but with enabling PASID it needs to be handled in the buffer
     offset calculation and in the permission bitmaps.

   - Avoid a gazillion of repeated CPUID invocations in by caching the
     values early in the FPU/XSTATE code.

   - Enable CONFIG_WERROR in x86 defconfig.

   - Make the X86 defconfigs more useful by adapting them to Y2022
     reality"

* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu/xstate: Consolidate size calculations
  x86/fpu/xstate: Handle supervisor states in XSTATE permissions
  x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
  x86/fpu: Cache xfeature flags from CPUID
  x86/fpu/xsave: Initialize offset/size cache early
  x86/fpu: Remove unused supervisor only offsets
  x86/fpu: Remove redundant XCOMP_BV initialization
  x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
  x86/config: Make the x86 defconfigs a bit more usable
  x86/defconfig: Enable WERROR
  selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
  x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation

Pull RT signal fix from Thomas Gleixner:
 "Revert the RT related signal changes. They need to be reworked and
  generalized"

* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"

Pull more dma-mapping updates from Christoph Hellwig:

 - fix a regression in dma remap handling vs AMD memory encryption (me)

 - finally kill off the legacy PCI DMA API (Christophe JAILLET)

* tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: move pgprot_decrypted out of dma_pgprot
  PCI/doc: cleanup references to the legacy PCI DMA API
  PCI: Remove the deprecated "pci-dma-compat.h" API

Pull ARM fixes from Russell King:

 - avoid unnecessary rebuilds for library objects

 - fix return value of __setup handlers

 - fix invalid input check for "crashkernel=" kernel option

 - silence KASAN warnings in unwind_frame

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
  ARM: 9190/1: kdump: add invalid input check for 'crashkernel=0'
  ARM: 9187/1: JIVE: fix return value of __setup handler
  ARM: 9189/1: decompressor: fix unneeded rebuilds of library objects

This reverts commit 7dabfa2b. There are
multiple reports that this breaks boot on various systems. The common
theme is that orphan clks are having rates set on them when that isn't
expected. Let's revert it out for now so that -rc1 boots.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/366a0232-bb4a-c357-6aa8-636e398e05eb@samsung.com
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220403022818.39572-1-sboyd@kernel.org