- 09 Dec, 2020 32 commits
-
-
Adrian Hunter authored
Intel controllers can end up in an unrecoverable state after a hibernate exit error unless a full reset and restore is done before anything else. Force that to happen. Link: https://lore.kernel.org/r/20201207083120.26732-4-adrian.hunter@intel.comSigned-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Adrian Hunter authored
The expectation for suspend-to-disk is that devices will be powered-off, so the UFS device should be put in PowerDown mode. If spm_lvl is not 5, then that will not happen. Change the pm callbacks to force spm_lvl 5 for suspend-to-disk poweroff. Link: https://lore.kernel.org/r/20201207083120.26732-3-adrian.hunter@intel.comSigned-off-by:
-
Adrian Hunter authored
Currently, ufshcd-pci is the only UFS driver with support for suspend-to-disk PM callbacks (i.e. freeze/thaw/restore/poweroff). These callbacks are set by the macro SET_SYSTEM_SLEEP_PM_OPS to the same functions as system suspend/resume. That will work with spm_lvl 5 because spm_lvl 5 will result in a full restore for the ->restore() callback. In the absence of a full restore, the host controller registers will have values set up by the restore kernel (the kernel that boots and loads the restore image) which are not necessarily the same. However it turns out, the only registers that sometimes need restore are the base address registers. This has gone un-noticed because, depending on IOMMU settings, the kernel can end up allocating the same addresses every time. For Intel controllers, an spm_lvl other than 5 can be used, so to support S4 (suspend-to-disk) with spm_lvl other than 5, restore the base address registers. Link: https://lore.kernel.org/r/20201207083120.26732-2-adrian.hunter@intel.comSigned-off-by:
-
Stanley Chu authored
For some devices which need extra delay after VCC power down, VCC shall be kept always-on in some MediaTek UFS platforms to ensure the stability of such devices because the extra delay may not be enough in those platforms. Link: https://lore.kernel.org/r/20201207054955.24366-3-stanley.chu@mediatek.comReviewed-by:
Andy Teng <andy.teng@mediatek.com> Signed-off-by:
Stanley Chu <stanley.chu@mediatek.com> Signed-off-by:
-
Stanley Chu authored
Introduce a flag "always_on" in struct ufs_vreg to allow vendors to keep the regulator always-on. Link: https://lore.kernel.org/r/20201207054955.24366-2-stanley.chu@mediatek.comReviewed-by:
-
Randall Huang authored
If RPMB is not provisioned, we may see RPMB failure after UFS suspend/resume. Inject request_sense to clear uac in ufshcd reset flow. Link: https://lore.kernel.org/r/20201201041402.3860525-1-jaegeuk@kernel.orgReported-by:
kernel test robot <lkp@intel.com> Reviewed-by:
Randall Huang <huangrandall@google.com> Signed-off-by:
Leo Liou <leoliou@google.com> Signed-off-by:
Jaegeuk Kim <jaegeuk@google.com> Signed-off-by:
-
Bean Huo authored
Change dev_err() print message from "dme-reset" to "dme_enable" in function ufshcd_dme_enable(). Link: https://lore.kernel.org/r/20201207190137.6858-3-huobean@gmail.comAcked-by:
Alim Akhtar <alim.akhtar@samsung.com> Acked-by:
Avri Altman <avri.altman@wdc.com> Signed-off-by:
Bean Huo <beanhuo@micron.com> Signed-off-by:
-
Bean Huo authored
POWER_DESC_MAX_SIZE is unused, remove it. Link: https://lore.kernel.org/r/20201207190137.6858-2-huobean@gmail.comAcked-by:
-
Suganath Prabu S authored
Update driver version to 36.100.00.00 Link: https://lore.kernel.org/r/20201126094311.8686-9-suganath-prabu.subramani@broadcom.comSigned-off-by:
Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by:
-
Suganath Prabu S authored
If a firmware update adds support for the trigger pages, then the driver should handle this by writing the existing trigger data from the driver's internal data structure to the corresponding trigger pages in NVRAM. Also handle the case where the trigger page capability is no longer present after a firmware downgrade. Link: https://lore.kernel.org/r/20201126094311.8686-8-suganath-prabu.subramani@broadcom.comSigned-off-by:
-
Suganath Prabu S authored
This page is used to store information about MPI (IOC Status & LogInfo) triggers. Driver Persistent Trigger Page-4 format: ------------------------------------------------------- | 31 24 23 16 15 8 7 0| Byte ------------------------------------------------------- | PageType | PageNumber | Reserved | PageVersion | 0x00 -------------------------------------------------------- | Reserved | ExtPageType | ExtPageLength | 0x04 -------------------------------------------------------- | Reserved | NumMpiTriggerEntries | 0x08 -------------------------------------------------------- | MPITriggerEntry[0] | 0x0C -------------------------------------------------------- | … | -------------------------------------------------------- | MPITriggerEntry[19] | 0xA4 -------------------------------------------------------- NumMpiTriggerEntries: This field indicates number of MPI (IOC Status & LogInfo) trigger entries stored in this page. Currently driver is supporting a maximum of 20-MPI trigger entries. MPITriggerEntry: ----------------------------------------------------- | 31 16 15 0 | ----------------------------------------------------- | Reserved | IOCStatus | ----------------------------------------------------- | IOCLogInfo | ----------------------------------------------------- IOCStatus => Status value from the IOC IOCLogInfo => Specific value that supplements the IOCStatus. Link: https://lore.kernel.org/r/20201126094311.8686-7-suganath-prabu.subramani@broadcom.comReported-by:
-
Suganath Prabu S authored
Trigger Page3 is used to store information about SCSI Sense triggers: Persistent Trigger Page-3 ------------------------------------------------------------------ | 31 24 23 16 15 8 7 0| Byte ------------------------------------------------------------------ | PageType | PageNumber | Reserved | PageVersion | 0x00 ------------------------------------------------------------------ | Reserved | ExtPageType | ExtPageLen | 0x04 ------------------------------------------------------------------ | Reserved | NumScsiSense | TriggerEntries | 0x08 ------------------------------------------------------------------ | ScsiSenseTriggerEntry[0] | 0x0C ------------------------------------------------------------------ | … … | ------------------------------------------------------------------ | ScsiSenseTriggerEntry[19] | 0x58 ------------------------------------------------------------------ NumScsiSenseTriggerEntries: This field indicates number of SCSI Sense trigger entries stored in this page. Currently driver is supporting a maximum of 20-SCSI Sense trigger entries. ScsiSenseTriggerEntry: ----------------------------------------------- | 31 24 23 16 15 8 7 0 | ----------------------------------------------- | Reserved | SenseKey | ASC | ASCQ | ----------------------------------------------- ASCQ => Additional Sense Code Qualifier ASC => Additional Sense Code SenseKey => Sense Key values ASCQ => Additional Sense Code Qualifier ASC => Additional Sense Code SenseKey => Sense Key values Link: https://lore.kernel.org/r/20201126094311.8686-6-suganath-prabu.subramani@broadcom.comReported-by:
-
Suganath Prabu S authored
Trigger Page2 is used to store information about Event triggers: 31 24 23 16 15 8 7 0 Byte ----------------------------------------------- |PageType |PageNumber |Reserved |PageVersion| 0x00 ----------------------------------------------- |Reserved |ExtPageType | ExtPageLength | 0x04 ----------------------------------------------- | Reserved | NumMPIEventTriggers | 0x08 ----------------------------------------------- | MPIEventTriggerEntries | 0x0C | | 0xFC ----------------------------------------------- Number of MPI Event Trigger Entries currently stored in this page. If this is set to zero, there are no valid MPI-Event-Trigger entries available in this page. MPIEventTriggerEntry: - MPIEventCode [15:00] MPI Event code specified in MPI-Spec - MPIEventCodeSpecific [16:31] For Event Code “MPI2_EVENT_LOG_ENTRY_ADDED (0x0021)”, this field specifies the Log-Entry-Qualifier. For all other Event Codes, this field is reserved and not used Maximum of 20-event trigger entries can be stored in this page. Link: https://lore.kernel.org/r/20201126094311.8686-5-suganath-prabu.subramani@broadcom.comReported-by:
-
Suganath Prabu S authored
Trigger Page 1 is used to store information about Master triggers. Below are the Master trigger conditions: Bit[3] Trigger condition for Device Removal event Bit[2] Trigger condition for TM command issued by driver Bit[1] Trigger condition for Adapter reset issued by driver Bit[0] Trigger condition for IOC Fault state During driver load, if Master trigger type bit is enabled in the Persistent Trigger Page0, then read the Persistent Trigger Page1 and update the IOC instance's diag_trigger_master.MasterData with Persistent Trigger Page1's MasterTriggerFlags. Link: https://lore.kernel.org/r/20201126094311.8686-4-suganath-prabu.subramani@broadcom.comReported-by:
-
Suganath Prabu S authored
The user can set trigger values in order to collect the IOC's host trace buffer automatically upon detecting certain conditions. However, the trigger values that the user sets are not persistent across system reboot or reload of the driver. In order to make the user trigger settings persistent, these trigger values need to be saved in the IOC's NVRAM pages: - Driver Persistent Trigger Page 0: This page is used to store list of trigger types that are enabled - Driver Persistent Trigger Page 1: This page stores the list of Master triggers that are enabled - Driver Persistent Trigger Page 2: This page stores the list of MPI Event Triggers that are enabled - Driver Persistent Trigger Page 3: This page stores the list of SCSI Sense Triggers that are enabled - Driver Persistent Trigger Page 4: This page stores the list of IOCStatus-LogInfo Triggers that are enabled. Whenever user configures triggers, the driver persists the values in the corresponding trigger pages. When the driver is subsequently reloaded, the driver reads the values from the trigger pages and configures the triggers accordingly. During firmware upload operation, if the newer firmware supports the trigger page feature, then driver persists the configured diag trigger values to NVRAM. Link: https://lore.kernel.org/r/20201126094311.8686-3-suganath-prabu.subramani@broadcom.comReported-by: -
Suganath Prabu S authored
The controller time currently gets updated with host time during driver load or when a controller reset is issued. I.e. when host issues the IOCInit request message to the HBA firmware. This IOCInit message has a field named 'TimeStamp' with which the host updates the controller time. Sometimes controller time drifts with respect to the host and it is difficult to correlate host logs with controller logs. Issuing a controller reset to sync the time would impact in-flight I/O and is not a viable option. Instead the driver now sends an IO_UNIT_CONTROL Request to sync the time periodically. This is done from the watchdog thread which gets invoked every second. The time synchronization interval is specified in the 'TimeSyncInterval' field in Manufacturing Page11 by the controller: TimeSyncInterval - 8 bits bits 0-6: Time stamp Synchronization interval value bit 7: Time stamp Synchronization interval unit, (if this bit is one then Timestamp Synchronization interval value is specified in terms of hours else Timestamp Synchronization interval value is specified in terms of minutes). The driver keeps track of the timer using IOC's timestamp_update_count field. This field value gets incremented whenever the watchdog thread gets invoked. And whenever this field value is greater than or equal to the Time Stamp Synchronization interval value, the driver sends the IO_UNIT_CONTROL Request message to controller to update the time and then it resets the timestamp_update_count field to zero. Link: https://lore.kernel.org/r/20201126094311.8686-2-suganath-prabu.subramani@broadcom.comReported-by: -
Nilesh Javali authored
Link: https://lore.kernel.org/r/20201202132312.19966-16-njavali@marvell.comReviewed-by:
Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
Nilesh Javali <njavali@marvell.com> Signed-off-by:
-
Arun Easi authored
Due to a bug in the older scan logic, when a once lost device re-appeared, it was not discovered. Fix this by resetting login_retry counter upon device discovery. This is applicable only for 4G and older HBAs. Link: https://lore.kernel.org/r/20201202132312.19966-15-njavali@marvell.comReviewed-by:
Arun Easi <aeasi@marvell.com> Signed-off-by:
-
Saurav Kashyap authored
Driver unload with I/Os in flight causes server to crash. Complete I/O with DID_IMM_RETRY if fcport undergoing deletion. CPU: 44 PID: 35008 Comm: qla2xxx_4_dpc Kdump: loaded Tainted: G OE X 5.3.18-22-default #1 SLE15-SP2 (unreleased) Hardware name: HPE ProLiant DL380 Gen10/ProLiant DL380 Gen10, BIOS U30 07/16/2020 RIP: 0010:dma_direct_unmap_sg+0x24/0x60 Code: 4c 8b 04 24 eb b9 0f 1f 44 00 00 85 d2 7e 4e 41 57 4d 89 c7 41 56 41 89 ce 41 55 49 89 fd 41 54 41 89 d4 55 31 ed 53 48 89 f3 <8b> 53 18 48 8b 73 10 4d 89 f8 44 89 f1 4c 89 ef 83 c5 01 e8 44 ff RSP: 0018:ffffc0c661037d88 EFLAGS: 00010046 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000002 RDX: 000000000000001d RSI: 0000000000000000 RDI: ffff9a51ee53b0b0 RBP: 0000000000000000 R08: 0000000000000000 R09: ffff9a51ee53b0b0 R10: ffffc0c646463dc8 R11: ffff9a4a067087c8 R12: 000000000000001d R13: ffff9a51ee53b0b0 R14: 0000000000000002 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff9a523f800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000018 CR3: 000000043740a004 CR4: 00000000007606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: qla2xxx_qpair_sp_free_dma+0x20d/0x3c0 [qla2xxx] qla2xxx_qpair_sp_compl+0x35/0x90 [qla2xxx] __qla2x00_abort_all_cmds+0x180/0x390 [qla2xxx] ? qla24xx_process_purex_list+0x100/0x100 [qla2xxx] qla2x00_abort_all_cmds+0x5e/0x80 [qla2xxx] qla2x00_do_dpc+0x317/0xa30 [qla2xxx] kthread+0x10d/0x130 ? kthread_park+0xa0/0xa0 ret_from_fork+0x35/0x40 Link: https://lore.kernel.org/r/20201202132312.19966-14-njavali@marvell.comReviewed-by:Saurav Kashyap <skashyap@marvell.com> Signed-off-by:
-
Saurav Kashyap authored
The call trace was because workqueue was allocated without any flags, added WQ_MEM_RECLAIM as flag when allocating. kernel: workqueue: WQ_MEM_RECLAIM kblockd:blk_mq_run_work_fn is flushing !WQ_MEM_RECLAIM qla2xxx_wq:0x0 kernel: WARNING: CPU: 0 PID: 2475 at kernel/workqueue.c:2593 check_flush_dependency+0x110/0x130 kernel: CPU: 0 PID: 2475 Comm: kworker/0:1H Kdump: loaded Tainted: G OE --------- - - 4.18.0-193.el8.x86_64 #1 kernel: Hardware name: HPE ProLiant XL170r Gen10/ProLiant XL170r Gen10, BIOS U38 05/21/2019 kernel: Workqueue: kblockd blk_mq_run_work_fn kernel: RIP: 0010:check_flush_dependency+0x110/0x130 kernel: Code: ff ff 48 8b 50 18 48 8d 8b b0 00 00 00 49 89 e8 48 81 c6 b0 00 00 00 48 c7 c7 00 1e e9 95 c6 05 dc 9a 2f 01 01 e8 1a 42 fe ff <0f> 0b e9 0a ff ff ff 80 3d ca 9a 2f 01 0 0 75 95 e9 41 ff ff ff 90 kernel: RSP: 0018:ffffa40f48b2baf8 EFLAGS: 00010282 kernel: RAX: 0000000000000000 RBX: ffff946795282600 RCX: 0000000000000000 kernel: RDX: 000000000000005f RSI: ffffffff96a1af7f RDI: 0000000000000246 kernel: RBP: 0000000000000000 R08: ffffffff96a1af20 R09: 0000000000029480 kernel: R10: 00080c89bb3e7462 R11: 00000000000009ab R12: ffff946773628000 kernel: R13: 0000000000000282 R14: 0000000000000246 R15: ffffa40f48b2bb40 kernel: FS: 0000000000000000(0000) GS:ffff94679fa00000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00005570c4b60110 CR3: 000000029140a005 CR4: 00000000007606f0 kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 kernel: PKRU: 55555554 kernel: Call Trace: kernel: flush_workqueue+0x13a/0x440 kernel: qla2x00_wait_for_sess_deletion+0x1d6/0x200 [qla2xxx] kernel: ? finish_wait+0x80/0x80 kernel: qla2xxx_disable_port+0x2b/0x30 [qla2xxx] kernel: qla2x00_process_vendor_specific+0x1dc9/0x2d20 [qla2xxx] kernel: ? blk_rq_map_sg+0x195/0x570 kernel: qla24xx_bsg_request+0x1a3/0xf90 [qla2xxx] Link: https://lore.kernel.org/r/20201202132312.19966-13-njavali@marvell.comReviewed-by:
-
Arun Easi authored
Flash update failed due to missing endian conversion in FLT region access as well as in checksum computation. Link: https://lore.kernel.org/r/20201202132312.19966-12-njavali@marvell.comReviewed-by:
-
Saurav Kashyap authored
Call trace observed while shutting down the adapter ports (LINK DOWN). Handle aborts correctly. localhost kernel: INFO: task nvme:44209 blocked for more than 120 seconds. localhost kernel: "echo 0 >/proc/sys/kernel/hung_task_timeout_secs" disables this message. localhost kernel: nvme D ffff88b45fb5acc0 0 44209 1 0x00000080 localhost kernel: Call Trace: localhost kernel: [<ffffffffbd187169>] schedule+0x29/0x70 localhost kernel: [<ffffffffbd184c51>] schedule_timeout+0x221/0x2d0 localhost kernel: [<ffffffffbcad7229>] ? ttwu_do_wakeup+0x19/0xe0 localhost kernel: [<ffffffffbcad735f>] ? ttwu_do_activate+0x6f/0x80 localhost kernel: [<ffffffffbcada830>] ? try_to_wake_up+0x190/0x390 localhost kernel: [<ffffffffbd18751d>] wait_for_completion+0xfd/0x140 localhost kernel: [<ffffffffbcadaaf0>] ? wake_up_state+0x20/0x20 localhost kernel: [<ffffffffbcabe3da>] flush_work+0x10a/0x1b0 localhost kernel: [<ffffffffbcabb0f0>] ? move_linked_works+0x90/0x90 localhost kernel: [<ffffffffbcabe6cf>] flush_delayed_work+0x3f/0x50 localhost kernel: [<ffffffffc0452767>] nvme_fc_init_ctrl+0x657/0x6a0 [nvme_fc] localhost kernel: [<ffffffffc045293a>] nvme_fc_create_ctrl+0x18a/0x210 [nvme_fc] localhost kernel: [<ffffffffc028962f>] nvmf_dev_write+0x98f/0xb35 [nvme_fabrics] localhost kernel: [<ffffffffbcd08927>] ? security_file_permission+0x27/0xa0 localhost kernel: [<ffffffffbcc4db50>] vfs_write+0xc0/0x1f0 localhost kernel: [<ffffffffbcc4e92f>] SyS_write+0x7f/0xf0 localhost kernel: [<ffffffffbd193f92>] system_call_fastpath+0x25/0x2a Link: https://lore.kernel.org/r/20201202132312.19966-11-njavali@marvell.comReviewed-by:
-
Quinn Tran authored
FC-NVMe target discovery failed when initiator wwpn < target wwpn in an N2N (Direct Attach) config, where the driver was stuck on FCP PRLI mode and failed to retry with NVMe PRLI. Link: https://lore.kernel.org/r/20201202132312.19966-10-njavali@marvell.com Fixes: 84ed362a ("scsi: qla2xxx: Dual FCP-NVMe target port support”) Fixes: 983f1276 ("scsi: qla2xxx: Retry PLOGI on FC-NVMe PRLI failure”) Signed-off-by:
Quinn Tran <qutran@marvell.com> Signed-off-by:
-
Arun Easi authored
Some fields are not correctly byte swapped causing failure during initialization. As probe() returns failure, HBAs will not be claimed when this happens. qla2xxx [0007:01:00.0]-ffff:3: Secure Flash Update in FW: Supported qla2xxx [0007:01:00.0]-ffff:3: SCM in FW: Supported qla2xxx [0007:01:00.0]-00d2:3: Init Firmware **** FAILED ****. qla2xxx [0007:01:00.0]-00d6:3: Failed to initialize adapter - Adapter flags 2. qla2xxx 0007:01:00.1: enabling device (0140 -> 0142) qla2xxx [0007:01:00.1]-011c: : MSI-X vector count: 128. qla2xxx [0007:01:00.1]-001d: : Found an ISP2289 irq 18 iobase 0xd000080080004000. qla2xxx 0007:01:00.1: Using 64-bit direct DMA at offset 800000000000000 BUG: Bad page state in process insmod pfn:67118 page:f00000000168bd40 count:-1 mapcount:0 mapping: (null) index:0x0 page flags: 0x3ffff800000000() page dumped because: nonzero _count Modules linked in: qla2xxx(OE+) nvme_fc nvme_fabrics nvme_core scsi_transport_fc scsi_tgt nls_utf8 isofs ip6t_rpfilter ipt_REJECT nf_reject_ipv4 ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute bridge stp llc ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter nx_crypto ses enclosure scsi_transport_sas pseries_rng sg ip_tables xfs libcrc32c sr_mod cdrom sd_mod crc_t10dif crct10dif_generic crct10dif_common usb_storage ipr libata tg3 ptp pps_core dm_mirror dm_region_hash dm_log dm_mod CPU: 32 PID: 8560 Comm: insmod Kdump: loaded Tainted: G OE ------------ 3.10.0-957.el7.ppc64 #1 Call Trace: [c0000006dd7caa70] [c00000000001cca8] .show_stack+0x88/0x330 (unreliable) [c0000006dd7cab30] [c000000000ac3d88] .dump_stack+0x28/0x3c [c0000006dd7caba0] [c00000000029e48c] .bad_page+0x15c/0x1c0 [c0000006dd7cac40] [c00000000029f938] .get_page_from_freelist+0x11e8/0x1ea0 [c0000006dd7caf40] [c0000000002a1d30] .__alloc_pages_nodemask+0x1c0/0xc70 [c0000006dd7cb140] [c00000000002ba0c] .__dma_direct_alloc_coherent+0x8c/0x170 [c0000006dd7cb1e0] [d000000010a94688] .qla2x00_mem_alloc+0x10f8/0x1370 [qla2xxx] [c0000006dd7cb2d0] [d000000010a9c790] .qla2x00_probe_one+0xb60/0x22e0 [qla2xxx] [c0000006dd7cb540] [c0000000005de764] .pci_device_probe+0x204/0x300 [c0000006dd7cb600] [c0000000006ca61c] .driver_probe_device+0x2cc/0x6f0 [c0000006dd7cb6b0] [c0000000006cabec] .__driver_attach+0x10c/0x110 [c0000006dd7cb740] [c0000000006c5f04] .bus_for_each_dev+0x94/0x100 [c0000006dd7cb7e0] [c0000000006c94f4] .driver_attach+0x34/0x50 [c0000006dd7cb860] [c0000000006c8f58] .bus_add_driver+0x298/0x3b0 [c0000006dd7cb900] [c0000000006cb6e0] .driver_register+0xb0/0x1a0 [c0000006dd7cb980] [c0000000005dc474] .__pci_register_driver+0xc4/0xf0 [c0000006dd7cba10] [d000000010b94e20] .qla2x00_module_init+0x2a8/0x328 [qla2xxx] [c0000006dd7cbaa0] [c00000000000c130] .do_one_initcall+0x130/0x2e0 [c0000006dd7cbb50] [c0000000001b2e8c] .load_module+0x1afc/0x2340 [c0000006dd7cbd40] [c0000000001b3920] .SyS_finit_module+0xd0/0x130 [c0000006dd7cbe30] [c00000000000a284] system_call+0x38/0xfc Link: https://lore.kernel.org/r/20201202132312.19966-9-njavali@marvell.com Fixes: 9f2475fe ("scsi: qla2xxx: SAN congestion management implementation") Fixes: cf3c54fb ("scsi: qla2xxx: Add SLER and PI control support”) Reviewed-by:
-
Arun Easi authored
Crash stack: [576544.715489] Unable to handle kernel paging request for data at address 0xd00000000f970000 [576544.715497] Faulting instruction address: 0xd00000000f880f64 [576544.715503] Oops: Kernel access of bad area, sig: 11 [#1] [576544.715506] SMP NR_CPUS=2048 NUMA pSeries : [576544.715703] NIP [d00000000f880f64] .qla27xx_fwdt_template_valid+0x94/0x100 [qla2xxx] [576544.715722] LR [d00000000f7952dc] .qla24xx_load_risc_flash+0x2fc/0x590 [qla2xxx] [576544.715726] Call Trace: [576544.715731] [c0000004d0ffb000] [c0000006fe02c350] 0xc0000006fe02c350 (unreliable) [576544.715750] [c0000004d0ffb080] [d00000000f7952dc] .qla24xx_load_risc_flash+0x2fc/0x590 [qla2xxx] [576544.715770] [c0000004d0ffb170] [d00000000f7aa034] .qla81xx_load_risc+0x84/0x1a0 [qla2xxx] [576544.715789] [c0000004d0ffb210] [d00000000f79f7c8] .qla2x00_setup_chip+0xc8/0x910 [qla2xxx] [576544.715808] [c0000004d0ffb300] [d00000000f7a631c] .qla2x00_initialize_adapter+0x4dc/0xb00 [qla2xxx] [576544.715826] [c0000004d0ffb3e0] [d00000000f78ce28] .qla2x00_probe_one+0xf08/0x2200 [qla2xxx] Link: https://lore.kernel.org/r/20201202132312.19966-8-njavali@marvell.com Fixes: f73cb695 ("[SCSI] qla2xxx: Add support for ISP2071.") Cc: stable@vger.kernel.org Reviewed-by:
-
Arun Easi authored
Fix compile time errors reported on PPC systems, qla_gbl.h:991:20: error: inlining failed in call to always_inline ‘qla_nvme_abort_set_option’: function body not available Link: https://lore.kernel.org/r/20201202132312.19966-7-njavali@marvell.comSigned-off-by: -
Saurav Kashyap authored
NVMe commands can come only after successful addition of rport and NVMe connect, and rport is only registered after FW started bit is set. Remove the redundant check. Link: https://lore.kernel.org/r/20201202132312.19966-6-njavali@marvell.comReviewed-by:
-
Quinn Tran authored
The completion status 0x28 (ppc = be = 0x2800) below indicates session is not there, trigger session deletion. qla2xxx [000b:04:00.1]-8009:8: DEVICE RESET ISSUED nexus=8:1:51 cmd=c000001432d0f600. qla2xxx [000b:04:00.1]-5039:8: Async-tmf error - hdl=67b completion status(2800). qla2xxx [000b:04:00.1]-8030:8: TM IOCB failed (102). qla2xxx [000b:04:00.1]-800c:8: do_reset failed for cmd=c000001432d0f600. qla2xxx [000b:04:00.1]-800f:8: DEVICE RESET FAILED: Task management failed nexus=8:1:51 cmd=c000001432d0f600. qla2xxx [000b:04:00.1]-8009:8: DEVICE RESET ISSUED nexus=8:1:52 cmd=c000001432d0c200. qla2xxx [000b:04:00.1]-5039:8: Async-tmf error - hdl=67c completion status(2800). qla2xxx [000b:04:00.1]-8030:8: TM IOCB failed (102). Link: https://lore.kernel.org/r/20201202132312.19966-5-njavali@marvell.comReviewed-by:
-
Quinn Tran authored
Driver created too many QPairs(126) with 28xx adapter. Limit to the number of CPUs to minimize wasted resources. Link: https://lore.kernel.org/r/20201202132312.19966-4-njavali@marvell.comReviewed-by:
-
Saurav Kashyap authored
Change the message debug level. Link: https://lore.kernel.org/r/20201202132312.19966-3-njavali@marvell.comSigned-off-by:
-
Daniel Wagner authored
When the fcport is about to be deleted we should return EBUSY instead of ENODEV. Only for EBUSY will the request be requeued in a multipath setup. Also return EBUSY when the firmware has not yet started to avoid dropping the request. Link: https://lore.kernel.org/r/20201014073048.36219-1-dwagner@suse.de Link: https://lore.kernel.org/r/20201202132312.19966-2-njavali@marvell.comReviewed-by:
Daniel Wagner <dwagner@suse.de> Signed-off-by:
-
Colin Ian King authored
The variable rval is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed. Link: https://lore.kernel.org/r/20201204191810.1150995-1-colin.king@canonical.comSigned-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
- 08 Dec, 2020 5 commits
-
-
Tom Rix authored
The macro use will already have a semicolon. Remove unneeded escaped newline. Link: https://lore.kernel.org/r/20201130205509.3447316-1-trix@redhat.comReviewed-by:
Tom Rix <trix@redhat.com> Signed-off-by:
-
Zhang Changzhong authored
Return a negative error code from the error handling case instead of 0 as done elsewhere in this function. Link: https://lore.kernel.org/r/1607068060-31203-1-git-send-email-zhangchangzhong@huawei.com Fixes: 5df6d737 ("[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA") Reported-by:
Hulk Robot <hulkci@huawei.com> Reviewed-by:
Karan Tilak Kumar <kartilak@cisco.com> Signed-off-by:
Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by:
-
Arnd Bergmann authored
clang complains about a possible code path in which a variable is used without an initialization: drivers/scsi/ufs/ufshcd.c:7690:3: error: variable 'sdp' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized] BUG_ON(1); ^~~~~~~~~ include/asm-generic/bug.h:63:36: note: expanded from macro 'BUG_ON' #define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0) ^~~~~~~~~~~~~~~~~~~ Turn the BUG_ON(1) into an unconditional BUG() that makes it clear to clang that this code path is never hit. Link: https://lore.kernel.org/r/20201203223137.1205933-1-arnd@kernel.org Fixes: 4f3e900b ("scsi: ufs: Clear UAC for FFU and RPMB LUNs") Reviewed-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Ahmed S. Darwish authored
NCR5380_poll_politely2() uses in_interrupt() and irqs_disabled() to check if it is safe to sleep. Such usage in drivers is phased out and Linus clearly requested that code which changes behaviour depending on context should either be separated, or the context be explicitly conveyed in an argument passed by the caller. Below is a context analysis of NCR5380_poll_politely2() uppermost callers: - NCR5380_maybe_reset_bus(), task, invoked during device probe. -> NCR5380_poll_politely() -> do_abort() - NCR5380_select(), task, but can only sleep in the "release, then re-acquire" regions of the spinlock held by its caller. Sleeping invocations (lock released): -> NCR5380_poll_politely2() Atomic invocations (lock acquired): -> NCR5380_reselect() -> NCR5380_poll_politely() -> do_abort() -> NCR5380_transfer_pio() - NCR5380_intr(), interrupt handler -> NCR5380_dma_complete() -> NCR5380_transfer_pio() -> NCR5380_poll_politely() -> NCR5380_reselect() (see above) - NCR5380_information_transfer(), task, but can only sleep in the "release, then re-acquire" regions of the caller-held spinlock. Sleeping invocations (lock released): - NCR5380_transfer_pio() -> NCR5380_poll_politely() - NCR5380_poll_politely() Atomic invocations (lock acquired): - NCR5380_transfer_dma() -> NCR5380_dma_recv_setup() => generic_NCR5380_precv() -> NCR5380_poll_politely() => macscsi_pread() -> NCR5380_poll_politely() -> NCR5380_dma_send_setup() => generic_NCR5380_psend -> NCR5380_poll_politely2() => macscsi_pwrite() -> NCR5380_poll_politely() -> NCR5380_poll_politely2() -> NCR5380_dma_complete() -> NCR5380_transfer_pio() -> NCR5380_poll_politely() - NCR5380_transfer_pio() -> NCR5380_poll_politely - NCR5380_reselect(), atomic, always called with hostdata spinlock held. Since NCR5380_poll_politely2() already takes a "wait" argument in jiffies, use it to determine if the function can sleep. Modify atomic callers, which passed an unused wait value in terms of HZ, to pass zero. Link: https://lore.kernel.org/r/20201206075157.19067-1-a.darwish@linutronix.de Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: <linux-m68k@lists.linux-m68k.org> Suggested-by:Finn Thain <fthain@telegraphics.com.au> Co-developed-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by:
Ahmed S. Darwish <a.darwish@linutronix.de> Signed-off-by:
-
jintae jang authored
Invalidation check of arguments should have been checked before ufshcd_hold(). This can help to prevent ufshcd_hold()/ ufshcd_release() from being invoked unnecessarily. [mkp: removed unused out: labels] Link: https://lore.kernel.org/r/1606973132-5937-1-git-send-email-user@jang-Samsung-DeskTop-SystemReviewed-by:
jintae jang <jt77.jang@samsung.com> Signed-off-by:
-
- 07 Dec, 2020 3 commits
-
-
Can Guo authored
Dump registers and states prior to leaving IRQ handler when an AH8 error occurs. Link: https://lore.kernel.org/r/1606910644-21185-4-git-send-email-cang@codeaurora.orgReviewed-by:
Bao D. Nguyen <nguyenb@codeaurora.org> Reviewed-by:
Asutosh Das <asutoshd@codeaurora.org> Reviewed-by:
Hongwu Su <hongwus@codeaurora.org> Signed-off-by:
Can Guo <cang@codeaurora.org> Signed-off-by:
-
Can Guo authored
In current task abort routine, if task abort happens to the device W-LUN, the code directly jumps to ufshcd_eh_host_reset_handler() to perform a full reset and restore then returns FAIL or SUCCESS. Commands sent to the device W-LUN are most likely the SSU cmds sent during UFS PM operations. If such SSU cmd enters task abort routine when ufshcd_eh_host_reset_handler() flushes eh_work, it will get stuck there since err_handler is serialized with PM operations. In order to unblock above call path, we merely clean up the lrb taken by this cmd, queue the eh_work and return SUCCESS. Once the cmd is aborted, the PM operation which sends out the cmd just errors out, then err_handler shall be able to proceed with the full reset and restore. In this scenario, the cmd is aborted even before it is actually cleared by HW, set the lrb->in_use flag to prevent subsequent cmds, including SCSI cmds and dev cmds, from taking the lrb released from abort. The flag shall evetually be cleared in __ufshcd_transfer_req_compl() invoked by the full reset and restore from err_handler. [mkp: conflict with event logging series] Link: https://lore.kernel.org/r/1606910644-21185-3-git-send-email-cang@codeaurora.orgReviewed-by:
-
Can Guo authored
Serialize eh_work with system PM events and async scan to make sure eh_work does not run in parallel with them. Link: https://lore.kernel.org/r/1606910644-21185-2-git-send-email-cang@codeaurora.orgReviewed-by:
-
