There is a very simple mechanism to change and SDI's voltage which
consists of toggling some GPIOs. This scenario can be better handled
if we convert it to a GPIO regulator. This patch provides one which
can be read from Device Tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

So far, each ST-Ericsson board supported by Device Tree has been similar
enough to run though a single DT_MACHINE_INIT call. On the back of that
it has been suggested that we should reduce the number of compatible
strings in our dt_compat structure. After subsequent discussion with Arnd
Bergmann the conclusion was to list entries by platform as opposed to by
board.

The other suggestion was to use a single string which would cover all
supported platforms, but any wildcard entries would include unsupported
chipsets, such as the u5500 and potential new chips which no not yet have
DT functionality. Hence, the best solution which encompasses all supported
platforms, but no unsupported ones was to list the currently enabled four
chipsets; u8500, u8540, u9500 and u9540 instead.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The u8500 and u9540 DT_MACHINE_START calls are almost identical
at the moment, referencing exactly the same function pointers.
Until this changes we may as well convert the original one to
be more generic and use that instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When enabling ST-Ericsson's ccu9540 development board the board's
full name has not been used. This patch adapts all references of
the board's short name to how it should be referenced.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The u9540 supports 3 MMC devices. This patch enables two of them
and updates the configuration of the already enabled SDI4 port.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we add the device node for the SDI4 (MMC) port to the u9540
Device Tree source file. This will allow successful probing of
the internal MMC storage device when booting with DT enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the 3 UART nodes required to enable serial ports on the u9540.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

First level board support for the u9540.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch sees the creation of a sparse Device Tree file for
ST-Ericsson's latest development board supporting the latest
dual-core Cortex-a9 u9540 SoC.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

'st-ericsson,u8500' is too much of a broad name to be used for
any of the supported development boards supported by ST-Ericsson.
As such it was never used. It has no place to remain in the board
compatible list, hence why it's being removed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch allows the STMPE keypad driver to be successfully probed
and initialised during a Device Tree enabled boot sequence. It
contains all of the required properties needed to setup and map
each key on the 6x3 keypad located on the ST User Interface Board.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we apply the STMPE Multi-Functional Device's node to the
ST User Interface Board Device Tree file. It includes all of
the properties required for correct device initialsation.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The regulator_has_full_constraints() call is not required if we
are booting with Device Tree as it's assumed in this case.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It is possible to connect a BU21013 Touch Screen to all version
of the HREF which support the ST-UIB. This patch applies all the
necessary settings to the pre-v60 and v60+ HREF Device Trees.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

As there will be a Device Tree created for the UIBs, there is no
need to call the UIB initiation functions. Each device will be
detailed and registered from the Device Tree instead.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is a skeleton creation which will be populated with the devices
found on one of ST-Ericsson's (UIB) User Interface Board.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we apply required documentation for the Rohm BU21013 Touch
Screen driver which describe available properties and how to use
them.

Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

We're currently carrying two 'struct bu21013_platform_device's which
are identical for no apparent reason. Here we remove the extra burden
and apply the same information to the two different instances of the
bu21012_tp driver registration.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

To aid the kernel in its effort to move to DT only booting, we're
transplanting all Device Tree related code to cpu-db8500 which will
remain persistent throughout the transition. This change paths the
way for complete removal of board-mop500, which will be done once
the all DMA settings are moved into the respective DT source files.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Most devices have now been successfully DT:ed and each supported
platform has its own Device Tree source file. Hence the majority
of the platform specific device registration calls can now be
successfully removed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we ensure the SFH7741 Proximity Sensor is registered through
gpio-keys when booting with Device Tree enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

In ux500 platform code we currently support a number of devices.
Two of these devices are fairly similar, but have key differences.
Early (pre-v60) HREFs and the more up-to-date versions (v60+), and
they both need to be supported by Device Tree. Here we apply a DT
source file for the earlier versions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

There are two main versions of the ST-Ericsson hardware reference board,
each with subtle differences. These versions are described in current
platform data as 'mop500' for HREF v1.1 & v2.0 and 'hrefv60+' for latter
incarnations. However, the boards have much in common, so this patch
creates a .dtsi (Device Tree Source Include) file which describes the
similarities between the two boards and individual 'hrefprev60' and
'hrefv60plus' .dts files which depict the differences.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Snowball's external SD/MMC slot is only capable of 4 bit data
transfer, not 8 bits as previously thought. This is a simple
fixup moving to the correct settings.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we add the Device Tree nodes which are required to successfully
probe the MMCI driver which will enable the four cards available on
ST-Ericsson's HREF hardware development platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

In the DB8500 Reference Manual SDI devices are described as being
part of peripheral blocks. This is more in line with how these devices
are actually represented in hardware, so here we detail which
peripheral block each of the SDI devices belong in the node name.
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

An earlier change prevented User Interface Boards (UIBs) from being
initialised on boards which did not support them. This change had
the undesired effect of reordering the UIB initialisation calls with
I2C registration. Here we ensure UIBs are only setup after all
required infrastructure is already in place.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.
Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull ktest confusion fix from Steven Rostedt:
 "With the v3.7-rc2 kernel, the network cards on my target boxes were
  not being brought up.

  I found that the modules for the network was not being installed.
  This was due to the config CONFIG_MODULES_USE_ELF_RELA that came
  before CONFIG_MODULES, and confused ktest in thinking that
  CONFIG_MODULES=y was not found.

  Ktest needs to test all configs and not just stop if something starts
  with CONFIG_MODULES."

* tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Fix ktest confusion with CONFIG_MODULES_USE_ELF_RELA

Pull minor spi MXS fixes from Mark Brown:
 "These fixes are both pretty minor ones and are driver local."

* tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
  spi: mxs: Terminate DMA in case of DMA timeout
  spi: mxs: Assign message status after transfer finished

Pull arm-soc fixes from Arnd Bergmann:
 "Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.

  These come a little later than I had hoped but unfortunately we had a
  few of these patches cause regressions themselves and had to work out
  how to deal with those in the meantime."

* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
  Revert "ARM i.MX25: Fix PWM per clock lookups"
  ARM: versatile: fix versatile_defconfig
  ARM: mvebu: update defconfig with 3.7 changes
  ARM: at91: fix at91x40 build
  ARM: socfpga: Fix socfpga compilation with early_printk() enabled
  ARM: SPEAr: Remove unused empty files
  MAINTAINERS: Add arm-soc tree entry
  ARM: dts: mxs: add the "clock-names" for gpmi-nand
  ARM: ux500: Correct SDI5 address and add some format changes
  ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
  ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
  ARM: at91: drop duplicated config SOC_AT91SAM9 entry
  ARM: at91/i2c: change id to let i2c-at91 work
  ARM: at91/i2c: change id to let i2c-gpio work
  ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
  ARM: at91: fix external interrupt specification in board code
  ARM: at91: fix external interrupts in non-DT case
  ARM: at91: at91sam9g10: fix SOC type detection
  ARM: at91/tc: fix typo in the DT document
  ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
  ...

Functions generic_file_splice_read and generic_file_splice_write access
the pagecache directly. For block devices these functions must be locked
so that block size is not changed while they are in progress.

This patch is an additional fix for commit b87570f5 ("Fix a crash
when block device is read and block size is changed at the same time")
that locked aio_read, aio_write and mmap against block size change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use rcu_read_lock_sched / rcu_read_unlock_sched / synchronize_sched
instead of rcu_read_lock / rcu_read_unlock / synchronize_rcu.

This is an optimization. The RCU-protected region is very small, so
there will be no latency problems if we disable preempt in this region.

So we use rcu_read_lock_sched / rcu_read_unlock_sched that translates
to preempt_disable / preempt_disable. It is smaller (and supposedly
faster) than preemptible rcu_read_lock / rcu_read_unlock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch introduces new barrier pair light_mb() and heavy_mb() for
percpu rw semaphores.

This patch fixes a bug in percpu-rw-semaphores where a barrier was
missing in percpu_up_write.

This patch improves performance on the read path of
percpu-rw-semaphores: on non-x86 cpus, there was a smp_mb() in
percpu_up_read. This patch changes it to a compiler barrier and removes
the "#if defined(X86) ..." condition.

From: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 92063cee, it
was applied prematurely, causing this build error for
imx_v4_v5_defconfig:

arch/arm/mach-imx/clk-imx25.c: In function 'mx25_clocks_init':
arch/arm/mach-imx/clk-imx25.c:206:26: error: 'pwm_ipg_per' undeclared (first use in this function)
arch/arm/mach-imx/clk-imx25.c:206:26: note: each undeclared identifier is reported only once for each function it appears in

Sascha Hauer explains:
> There are several gates missing in clk-imx25.c. I have a patch which
> adds support for them and I seem to have missed that the above depends
> on it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

With the introduction of CONFIG_ARCH_MULTIPLATFORM, versatile is
no longer the default platform, so we need to enable
CONFIG_ARCH_VERSATILE explicitly in order for that to be selected
rather than the multiplatform configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The split of 370 and XP into two Kconfig options and the multiplatform
kernel support has changed a few Kconfig symbols, so let's update the
mvebu_defconfig file with the latest changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

patch 738a0fd7 "ARM: at91: fix external interrupts in non-DT case"
fixed a run-time error on some at91 platforms but did not apply
the same change to at91x40, which now doesn't build.

This changes at91x40 in the same way that the other platforms
were changed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Pull networking fixes from David Miller:
 "This is what we usually expect at this stage of the game, lots of
  little things, mostly in drivers.  With the occasional 'oops didn't
  mean to do that' kind of regressions in the core code."

 1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann

 2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.

 3) Lost error code on return from _rtl_usb_receive(), from Christian
    Lamparter.

 4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.

 5) Release resources on error in pch_gbe driver, from Veaceslav Falico.

 6) Default hop limit not set correctly in ip6_template_metrics[], fix
    from Li RongQing.

 7) Gianfar PTP code requests wrong kind of resource during probe, fix
    from Wei Yang.

 8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.

 9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
    Shoua, Dotan Barak, and Uri Habusha.

10) usbnet leaks memory on TX path, fix from Hemant Kumar.

11) Use socket state test, rather than presence of FIN bit packet, to
    determine FIONREAD/SIOCINQ value.  Fix from Eric Dumazet.

12) Fix cxgb4 build failure, from Vipul Pandya.

13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
    info dumps.  From Yuchung Cheng.

14) Fix leak of security path in kfree_skb_partial().  Fix from Eric
    Dumazet.

15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
    Veaceslav Falico.

16) Fix MAINTAINERS file pattern for networking drivers, from Jean
    Delvare.

17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.

18) VLAN device type change restriction is too strict, and should not
    trigger for the automatically generated vlan0 device.  Fix from Jiri
    Pirko.

19) Make PMTU/redirect flushing work properly again in ipv4, from
    Steffen Klassert.

20) Fix memory corruptions by using kfree_rcu() in netlink_release().
    From Eric Dumazet.

21) More qmi_wwan device IDs, from Bjørn Mork.

22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
    infrastructure, from Elison Niven.

23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
  tilegx: fix some issues in the SW TSO support
  qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
  net: usb: Fix memory leak on Tx data path
  net/mlx4_core: Unmap UAR also in the case of error flow
  net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
  net/mlx4_en: Fix double-release-range in tx-rings
  bas_gigaset: fix pre_reset handling
  vhost: fix mergeable bufs on BE hosts
  gianfar_ptp: use iomem, not ioports resource tree in probe
  ipv6: Set default hoplimit as zero.
  NET_VENDOR_TI: make available for am33xx as well
  pch_gbe: fix error handling in pch_gbe_up()
  b43: Fix oops on unload when firmware not found
  mwifiex: clean up scan state on error
  mwifiex: return -EBUSY if specific scan request cannot be honored
  brcmfmac: fix potential NULL dereference
  Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
  ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
  rt2x00: usb: fix reset resume
  rtlwifi: pass rx setup error code to caller
  ...