Currently we set the length field in the DAWR to 0 which defaults it to one
double word (64bits) which is the same as the DABR.

Change this so that we can set it to longer values as supported by the DAWR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

perf/Power: PERF_EVENT_IOC_ENABLE does not reenable event

If we disable a perf event because we exceeded the specified ->event_limit,
power_pmu_stop() sets the PERF_HES_STOPPED flag on the event.

If the application then re-enables the event using PERF_EVENT_IOC_ENABLE
ioctl, we don't ever clear this STOPPED flag. Consequently, the user space
is never notified of the event.

Following message has more background and test case.

    http://lists.eecs.utk.edu/pipermail/ptools-perfapi/2012-October/002528.html

Used the following test cases to verify that this patch works on latest PAPI.

	$ papi.git/src/ctests/nonthread PAPI_TOT_CYC@5000000

	$ papi.git/src/ctests/overflow_single_event

Changelog[v2]:
	- [Paul Mackerras] Also clear PERF_HES_UPTODATE flag since we are
	  restarting the event; cleanup comments and patch description.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Use local_paca directly in macro SHARED_PROCESSOR, as all processors
have the same value for the field shared_proc, so we don't need care
racy here.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Uprobes uses emulate_step in sstep.c, but we haven't explicitly specified
the dependency. On pseries HAVE_HW_BREAKPOINT protects us, but 44x has no
such luxury.

Consolidate other users that depend on sstep and create a new config option.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: linuxppc-dev@ozlabs.org
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

CTS-1000 is based on P4080. GPIO 27 is used to signal the FPGA to
switch off power, and also associates IRQ 8 with front-panel button
press (which we use to call orderly_poweroff()).

The relevant device-tree looks like this:

	gpio0: gpio@130000 {
		compatible = "fsl,qoriq-gpio";
		reg = <0x130000 0x1000>;
		interrupts = <55 2 0 0>;
		#gpio-cells = <2>;
		gpio-controller;

		/* Allows powering off the system via GPIO signal. */
		gpio-halt@27 {
			compatible = "sgy,gpio-halt";
			gpios = <&gpio0 27 0>;
			interrupts = <8 1 0 0>;
		};
	};

Because the driver cannot match on sgy,gpio-halt (because the node is never
processed through of_platform), it matches on fsl,qoriq-gpio and then
checks child nodes for the matching sgy,gpio-halt. This also ensures that
the GPIO controller is detected prior to sgy_cts1000's probe callback,
since that node wont match via of_platform until the controller is
registered.

Also, because the GPIO handler for triggering system poweroff might sleep,
the IRQ uses a workqueue to call orderly_poweroff().

As a final note, this driver may be expanded for other features specific to
the CTS-1000.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Jack Smith <jack.s@servergy.com>
Cc: Vihar Rai <vihar.r@servergy.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

While this should be harmless now that distribute_irqs
obeys MPIC_SINGLE_DEST_CPU, there's no reason to enable this
on mpc85xx/mpc86xx since MPIC_SINGLE_DEST_CPU will always be set.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Previously we were setting an illegal configuration on mpc85xx
MPICs if CONFIG_IRQ_ALL_CPUS is enabled (which for some reason it is
in mpc85xx_smp_defconfig).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We have a mix of decimal and hex here, so lets make them consistently
hex.  Also, strace will print them in hex if it can't decode them, so
having them in hex here makes it easier to match up.

No functional change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The only persistent change made by this loop is calling
memblock_set_node() once for each memblock, which is not useful (and has
no effect) as memblock_set_node() is not called with any
memblock-specific parameters.

Subsistute a single memblock_set_node().
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Merge "merge" branch to bring in various bug fixes that are
going into 3.8

With lazy interrupt, we always call __check_irq_replaysome with
decrementers_next_tb to check if we need to replay timer interrupt.
So in hotplug case we also need to set decrementers_next_tb as MAX
to make sure __check_irq_replay don't replay timer interrupt
when return as we expect, otherwise we'll trap here infinitely.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

the variable backup_current_thread_info isn't freed before existing the
function.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an
error.  The calculation is should be to shift left by (max_cntrs - cntr) times
the width of the pmsel field width.  However, the #define OPROFILE_MAX_PMC_NUM
was used instead of OPROFILE_PMSEL_FIELD_WIDTH.  This patch fixes the
calculation.
Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

commit f96972f2 "kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()"

added a call to disable_nonboot_cpus() on kernel_restart(), which tries
to shutdown all the CPUs except the first one. The issue with the PA
Semi, is that it does not support CPU hotplug.

When the call is made to __cpu_down(), it calls the notifiers
CPU_DOWN_PREPARE, and then tries to take the CPU down.

One of the notifiers to the CPU hotplug code, is the cpufreq. The
DOWN_PREPARE will call __cpufreq_remove_dev() which calls
cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O
that is used by an interrupt that goes off constantly
(system_reset_common, but it goes off during normal system operations
too). I'm not sure exactly what this interrupt does.

Running a simple function trace, you can see it goes off quite a bit:

# tracer: function
#
#           TASK-PID    CPU#    TIMESTAMP  FUNCTION
#              | |       |          |         |
          <idle>-0     [001]  1558.859363: .pasemi_system_reset_exception <-.system_reset_exception
          <idle>-0     [000]  1558.860112: .pasemi_system_reset_exception <-.system_reset_exception
          <idle>-0     [000]  1558.861109: .pasemi_system_reset_exception <-.system_reset_exception
          <idle>-0     [001]  1558.861361: .pasemi_system_reset_exception <-.system_reset_exception
          <idle>-0     [000]  1558.861437: .pasemi_system_reset_exception <-.system_reset_exception

When the region is unmapped, the system crashes with:

Disabling non-boot CPUs ...
Error taking CPU1 down: -38
Unable to handle kernel paging request for data at address 0xd0000800903a0100
Faulting instruction address: 0xc000000000055fcc
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=64 NUMA PA Semi PWRficient
Modules linked in: shpchp
NIP: c000000000055fcc LR: c000000000055fb4 CTR: c0000000000df1fc
REGS: c0000000012175d0 TRAP: 0300   Not tainted  (3.8.0-rc4-test-dirty)
MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI>  CR: 24000088  XER: 00000000
SOFTE: 0
DAR: d0000800903a0100, DSISR: 42000000
TASK = c0000000010e9008[0] 'swapper/0' THREAD: c000000001214000 CPU: 0
GPR00: d0000800903a0000 c000000001217850 c0000000012167e0 0000000000000000
GPR04: 0000000000000000 0000000000000724 0000000000000724 0000000000000000
GPR08: 0000000000000000 0000000000000000 0000000000000001 0000000000a70000
GPR12: 0000000024000080 c00000000fff0000 ffffffffffffffff 000000003ffffae0
GPR16: ffffffffffffffff 0000000000a21198 0000000000000060 0000000000000000
GPR20: 00000000008fdd35 0000000000a21258 000000003ffffaf0 0000000000000417
GPR24: 0000000000a226d0 c000000000000000 0000000000000000 0000000000000000
GPR28: c00000000138b358 0000000000000000 c000000001144818 d0000800903a0100
NIP [c000000000055fcc] .set_astate+0x5c/0xa4
LR [c000000000055fb4] .set_astate+0x44/0xa4
Call Trace:
[c000000001217850] [c000000000055fb4] .set_astate+0x44/0xa4 (unreliable)
[c0000000012178f0] [c00000000005647c] .restore_astate+0x2c/0x34
[c000000001217980] [c000000000054668] .pasemi_system_reset_exception+0x6c/0x88
[c000000001217a00] [c000000000019ef0] .system_reset_exception+0x48/0x84
[c000000001217a80] [c000000000001e40] system_reset_common+0x140/0x180
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit 12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull GFS2 fix from Steven Whitehouse.

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: fix skip unlock condition

Pull IOMMU fix from Joerg Roedel:
 "One fix for the AMD IOMMU driver to work around broken BIOSes found in
  the field.  Some BIOSes forget to enable a workaround for a hardware
  problem which might cause the IOMMU to stop working under high load
  conditions.  The fix makes sure this workaround is enabled."

* tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround

Pull MFD fixes from Samuel Ortiz:
 "This is the first pull request for MFD fixes for 3.8

  We have some build failure fixes (twl4030, vexpress, abx500 and
  tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
  and some more hypothetical NULL pointers dereferences fixes for
  pcf50633 and max776xx.

  Then we also have additional rtsx fixes for a correct switch output
  voltage and clock divider correctness for rtl8411 (rtsx driver), and
  irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
  arizona and wm5102."

* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
  mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
  mfd: twl4030: Don't warn about uninitialized return code
  mfd: da9052/53 lockup fix
  mfd: rtsx: Add clock divider hook
  mmc: rtsx: Call MFD hook to switch output voltage
  mfd: rtsx: Add output voltage switch hook
  mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
  mfd: vexpress: Export global functions to fix build error
  mfd: arizona: Check errors from regcache_sync()
  mfd: tc3589x: Use simple irqdomain
  mfd: pcf50633: Init pcf->dev before using it
  mfd: max77693: Init max77693->dev before using it
  mfd: max77686: Init max77686->dev before using it
  mfd: db8500-prcmu: Fix irqdomain usage
  mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
  mfd: arizona: Disable control interface reporting for WM5102 and WM5110

Pull networking updates from David Miller:
 "Much more accumulated than I would have liked due to an unexpected
  bout with a nasty flu:

   1) AH and ESP input don't set ECN field correctly because the
      transport head of the SKB isn't set correctly, fix from Li
      RongQing.

   2) If netfilter conntrack zones are disabled, we can return an
      uninitialized variable instead of the proper error code.  Fix from
      Borislav Petkov.

   3) Fix double SKB free in ath9k driver beacon handling, from Felix
      Feitkau.

   4) Remove bogus assumption about netns cleanup ordering in
      nf_conntrack, from Pablo Neira Ayuso.

   5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric
      Dumazet.  It uses spin_is_locked() in it's test and is therefore
      unsuitable for UP.

   6) Fix SELINUX labelling regressions added by the tuntap multiqueue
      changes, from Paul Moore.

   7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin
      Nayak Sujir.

   8) CXGB4 driver sets interrupt coalescing parameters only on first
      queue, rather than all of them.  Fix from Thadeu Lima de Souza
      Cascardo.

   9) Fix regression in the dispatch of read/write registers in dm9601
      driver, from Tushar Behera.

  10) ipv6_append_data miscalculates header length, from Romain KUNTZ.

  11) Fix PMTU handling regressions on ipv4 routes, from Steffen
      Klassert, Timo Teräs, and Julian Anastasov.

  12) In 3c574_cs driver, add necessary parenthesis to "x << y & z"
      expression.  From Nickolai Zeldovich.

  13) macvlan_get_size() causes underallocation netlink message space,
      fix from Eric Dumazet.

  14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai
      Zeldovich.  Amusingly the zero check was already there, we were
      just performing it after the modulus :-)

  15) Some more splice bug fixes from Eric Dumazet, which fix things
      mostly eminating from how we now more aggressively use high-order
      pages in SKBs.

  16) Fix size calculation bug when freeing hash tables in the IPSEC
      xfrm code, from Michal Kubecek.

  17) Fix PMTU event propagation into socket cached routes, from Steffen
      Klassert.

  18) Fix off by one in TX buffer release in netxen driver, from Eric
      Dumazet.

  19) Fix rediculous memory allocation requirements introduced by the
      tuntap multiqueue changes, from Jason Wang.

  20) Remove bogus AMD platform workaround in r8169 driver that causes
      major problems in normal operation, from Timo Teräs.

  21) virtio-net set affinity and select queue don't handle
      discontiguous cpu numbers properly, fix from Wanlong Gao.

  22) Fix a route refcounting issue in loopback driver, from Eric
      Dumazet.  There's a similar fix coming that we might add to the
      macvlan driver as well.

  23) Fix SKB leaks in batman-adv's distributed arp table code, from
      Matthias Schiffer.

  24) r8169 driver gives descriptor ownership back the hardware before
      we're done reading the VLAN tag out of it, fix from Francois
      Romieu.

  25) Checksums not calculated properly in GRE tunnel driver fix from
      Pravin B Shelar.

26) Fix SCTP memory leak on namespace exit."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
  dm9601: support dm9620 variant
  SCTP: Free the per-net sysctl table on net exit. v2
  net: phy: icplus: fix broken INTR pin settings
  net: phy: icplus: Use the RGMII interface mode to configure clock delays
  IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
  sctp: set association state to established in dupcook_a handler
  ip6mr: limit IPv6 MRT_TABLE identifiers
  r8169: fix vlan tag read ordering.
  net: cdc_ncm: use IAD provided by the USB core
  batman-adv: filter ARP packets with invalid MAC addresses in DAT
  batman-adv: check for more types of invalid IP addresses in DAT
  batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
  net: loopback: fix a dst refcounting issue
  virtio-net: reset virtqueue affinity when doing cpu hotplug
  virtio-net: split out clean affinity function
  virtio-net: fix the set affinity bug when CPU IDs are not consecutive
  can: pch_can: fix invalid error codes
  can: ti_hecc: fix invalid error codes
  can: c_can: fix invalid error codes
  r8169: remove the obsolete and incorrect AMD workaround
  ...

The IOMMU may stop processing page translations due to a perceived lack
of credits for writing upstream peripheral page service request (PPR)
or event logs. If the L2B miscellaneous clock gating feature is enabled
the IOMMU does not properly register credits after the log request has
completed, leading to a potential system hang.

BIOSes are supposed to disable L2B micellaneous clock gating by setting
L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This
patch corrects that for those which do not enable this workaround.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>

The recent commit fb6791d1
included the wrong logic.  The lvbptr check was incorrectly
added after the patch was tested.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.

This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.

Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per-net sysctl table needs to be explicitly freed at
net exit.  Otherwise we see the following with kmemleak:

unreferenced object 0xffff880402d08000 (size 2048):
  comm "chrome_sandbox", pid 18437, jiffies 4310887172 (age 9097.630s)
  hex dump (first 32 bytes):
    b2 68 89 81 ff ff ff ff 20 04 04 f8 01 88 ff ff  .h...... .......
    04 00 00 00 a4 01 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff815b4aad>] kmemleak_alloc+0x21/0x3e
    [<ffffffff81110352>] slab_post_alloc_hook+0x28/0x2a
    [<ffffffff81113fad>] __kmalloc_track_caller+0xf1/0x104
    [<ffffffff810f10c2>] kmemdup+0x1b/0x30
    [<ffffffff81571e9f>] sctp_sysctl_net_register+0x1f/0x72
    [<ffffffff8155d305>] sctp_net_init+0x100/0x39f
    [<ffffffff814ad53c>] ops_init+0xc6/0xf5
    [<ffffffff814ad5b7>] setup_net+0x4c/0xd0
    [<ffffffff814ada5e>] copy_net_ns+0x6d/0xd6
    [<ffffffff810938b1>] create_new_namespaces+0xd7/0x147
    [<ffffffff810939f4>] copy_namespaces+0x63/0x99
    [<ffffffff81076733>] copy_process+0xa65/0x1233
    [<ffffffff81077030>] do_fork+0x10b/0x271
    [<ffffffff8100a0e9>] sys_clone+0x23/0x25
    [<ffffffff815dda73>] stub_clone+0x13/0x20
    [<ffffffffffffffff>] 0xffffffffffffffff

I fixed the spelling of sysctl_header so the code actually
compiles. -- EWB.
Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to IP_GRE GSO support, GRE can recieve non linear skb which
results in panic in case of GRE_CSUM.  Following patch fixes it by
using correct csum API.

Bug introduced in commit 6b78f16e (gre: add GSO support)
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While sctp handling a duplicate COOKIE-ECHO and the action is
'Association restart', sctp_sf_do_dupcook_a() will processing
the unexpected COOKIE-ECHO for peer restart, but it does not set
the association state to SCTP_STATE_ESTABLISHED, so the association
could stuck in SCTP_STATE_SHUTDOWN_PENDING state forever.
This violates the sctp specification:
  RFC 4960 5.2.4. Handle a COOKIE ECHO when a TCB Exists
  Action
  A) In this case, the peer may have restarted. .....
     After this, the endpoint shall enter the ESTABLISHED state.

To resolve this problem, adding a SCTP_CMD_NEW_STATE cmd to the
command list before SCTP_CMD_REPLY cmd, this will set the restart
association to SCTP_STATE_ESTABLISHED state properly and also avoid
I-bit being set in the DATA chunk header when COOKIE_ACK is bundled
with DATA chunks.
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We did this for IPv4 in b49d3c1e "net: ipmr: limit MRT_TABLE
identifiers" but we need to do it for IPv6 as well.  On IPv6 the name
is "pim6reg" instead of "pimreg" so there is one less digit allowed.

The strcpy() is in ip6mr_reg_vif().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.

VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 9992c2e2 (net: cdc_ncm: workaround for missing CDC Union)
added code to lookup an IAD for the interface we are probing.
This is redundant.  The USB core has already done the lookup
and saved the result in the USB interface struct.  Use that
instead.

Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included changes ares:
- fix an skb memleak in DAT
- fix the ARP filtering routine in DAT by preventing bogus entries to overwrite
  already existing ones in the local cache.
- fix the ARP filtering routine in DAT by preventing it to parse and add to the
  cache bogus entries
Signed-off-by: David S. Miller <davem@davemloft.net>

We never want multicast MAC addresses in the Distributed ARP Table, so it's
best to completely ignore ARP packets containing them where we expect unicast
addresses.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

There are more types of IP addresses that may appear in ARP packets that we
don't want to process. While some of these should never appear in sane ARP
packets, a 0.0.0.0 source is used for duplicate address detection and thus seen
quite often.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

The callers of batadv_dat_snoop_incoming_arp_reply() assume the skb has been
freed when it returns true; fix this by calling kfree_skb before returning as
it is done in batadv_dat_snoop_incoming_arp_request().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

John W. Linville says:

====================
This is a batch of fixes intende for the 3.8 stream.

Regarding the iwlwifi bits, Johannes says this:

"Please pull to get a single fix from Emmanuel for a bug I introduced due
to misunderstanding the code."

Regarding the mac80211 bits, Johannes says this:

"I have a few small fixes for you:
 * some mesh frames would cause encryption warnings -- fixes from Bob
 * scanning would pretty much break an association if we transmitted
   anything to the AP while scanning -- fix from Stanislaw
 * mode injection was broken by channel contexts -- fix from Felix
 * FT roaming was broken: hardware crypto would get disabled by it"

Along with that, a handful of other fixes confined to specific drivers.

Avinash Patil fixes a typo in a NULL check in mwifiex.

Larry Finger fixes a build warning in rtlwifi.  Seems safe...

Stanislaw Gruszka fixes iwlegacy to prevent microcode errors when
switching from IBSS mode to STA mode.

Felix Fietkau provides a trio of ath9k fixes related to proper tuning.

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Greear reported crashes in ip_rcv_finish() on a stress
test involving many macvlans.

We tracked the bug to a dst use after free. ip_rcv_finish()
was calling dst->input() and got garbage for dst->input value.

It appears the bug is in loopback driver, lacking
a skb_dst_force() before calling netif_rx().

As a result, a non refcounted dst, normally protected by a
RCU read_lock section, was escaping this section and could
be freed before the packet being processed.

  [<ffffffff813a3c4d>] loopback_xmit+0x64/0x83
  [<ffffffff81477364>] dev_hard_start_xmit+0x26c/0x35e
  [<ffffffff8147771a>] dev_queue_xmit+0x2c4/0x37c
  [<ffffffff81477456>] ? dev_hard_start_xmit+0x35e/0x35e
  [<ffffffff8148cfa6>] ? eth_header+0x28/0xb6
  [<ffffffff81480f09>] neigh_resolve_output+0x176/0x1a7
  [<ffffffff814ad835>] ip_finish_output2+0x297/0x30d
  [<ffffffff814ad6d5>] ? ip_finish_output2+0x137/0x30d
  [<ffffffff814ad90e>] ip_finish_output+0x63/0x68
  [<ffffffff814ae412>] ip_output+0x61/0x67
  [<ffffffff814ab904>] dst_output+0x17/0x1b
  [<ffffffff814adb6d>] ip_local_out+0x1e/0x23
  [<ffffffff814ae1c4>] ip_queue_xmit+0x315/0x353
  [<ffffffff814adeaf>] ? ip_send_unicast_reply+0x2cc/0x2cc
  [<ffffffff814c018f>] tcp_transmit_skb+0x7ca/0x80b
  [<ffffffff814c3571>] tcp_connect+0x53c/0x587
  [<ffffffff810c2f0c>] ? getnstimeofday+0x44/0x7d
  [<ffffffff810c2f56>] ? ktime_get_real+0x11/0x3e
  [<ffffffff814c6f9b>] tcp_v4_connect+0x3c2/0x431
  [<ffffffff814d6913>] __inet_stream_connect+0x84/0x287
  [<ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
  [<ffffffff8108d695>] ? _local_bh_enable_ip+0x84/0x9f
  [<ffffffff8108d6c8>] ? local_bh_enable+0xd/0x11
  [<ffffffff8146763c>] ? lock_sock_nested+0x6e/0x79
  [<ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
  [<ffffffff814d6b49>] inet_stream_connect+0x33/0x49
  [<ffffffff814632c6>] sys_connect+0x75/0x98

This bug was introduced in linux-2.6.35, in commit
7fee226a (net: add a noref bit on skb dst)

skb_dst_force() is enforced in dev_queue_xmit() for devices having a
qdisc.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a cpu notifier to virtio-net, so that we can reset the
virtqueue affinity if the cpu hotplug happens. It improve
the performance through enabling or disabling the virtqueue
affinity after doing cpu hotplug.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split out the clean affinity function to virtnet_clean_affinity().

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As Michael mentioned, set affinity and select queue will not work very
well when CPU IDs are not consecutive, this can happen with hot unplug.
Fix this bug by traversal the online CPUs, and create a per cpu variable
to find the mapping from CPU to the preferable virtual-queue.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>