This was a write only member
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

use brcms_pub->cur_etheraddr instead
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This was a read only member, replace it with pub->up.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This was a read only member.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replaced the usage with pub->associated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This was a read only member. The checks using BSS are replaced by
better fitting checks of the new type member.

The change in brcms_c_tbtt() was based on code from b43, in
brcms_c_ps_allowed() the same happens with BSS being true or false,
beaconing and probe responses are just needed in ap mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This makes it possible to easily check in which mode the device is
currently running. This also adds a function to start station mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

setting the tsf is needed to start a timer to make beaconing in AP mode
work.

This is based on older versions of brcmsmac and b43.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of defining the magic values in the code use constants.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

FW can be woken up even by accessing device registers; we need
not explicitily enable interrupts for doing this. Future PCIe
devices will not be woken up by writing to host registers.
This patch enables driver to wake up device by reading FW status
register.

Also devices with sleep cookie enabled need some more time before
proceeding with processing. Handle this by adding a delay loop.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We have received interrupt from device means FW is not sleeping.
In this case make sure wakeup handler for PCIe is not invoked by
setting adapter->pm_wakeup_fw_try to false.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enabling PCIe host interrupt may accidently wake up the card
when it's in sleep.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

commit 6236dc2e ("brcmsmac: remove some redundant chip common workarounds")
removed the last uses.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The spectral data provided via relay-fs introduces a buffering
latency given by the subbuf_size. To meet the requirements for
delay-sensitive applications (like real-time spectral plotter),
reduce subbuf_size and increase n_subbufs.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The BCM5354 SoC has a build in ieee80211 core rev 13 with a LP-PHY on
it. This devices has a sprom version 3 stored in the nvram. This patch
removes the warning and uses the opo values from the sprom as mentioned
in the specs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These attributes should be in the sprom for rev 2 and 3, but they were
not read out.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This was done accordingly to new specs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With this patch the same registers are written, but this access is now
protected by a lock.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using that IDs we can write workarounds for various cards
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, default VHT configuration from the firmware is used
for the VHT operations. Adding vhtcfg command to configure the
firmware based on input received from cfg.

Enable VHT for AP mode only when cfg80211_ap_settings has a
VHT IE i.e., when ieee80211ac is set to 1 in the hostapd.conf.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add proper alignment at first packet copy, to avoid extra copies made later
in networking stack.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move processing of received packets to tasklet from hard-irq context.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

RX path has extra copying of packets, that can be avoided.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use dedicated DMA coherent buffers for RX urbs, to avoid allocation of large
skbuffs in hard-irq context and improve performance.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Spin locks and completions are expensive in hard IRQ context and cause
problems with RT kernels.  In RT kernels, both spin locks and
completions can schedule(), so we can't use them in hard irq context.

Move handling code into the irq thread function to avoid that.
Reported-by: Gregoire Gentil <gregoire@alwaysinnovating.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

We were printing out all the hex dumps regardless of whether dynamic
debugging was enabled or not.  Now that print_hex_dump_debug() has
been implemented, we can use that instead.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Don't ignore dummy packets when our queues are empty. This causes dummy
packets never to be sent when traffic is not suspended by FW thresholds,
which happens only in high Tx throughput situations. This may hurt Rx
performance.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The wlcore state was checked without the mutex being taken. This leads
to WARN_ONs sometimes if a notification arrives when the driver
is on, but the mutex is only taken after it is off. This usually
happens if stopping the driver while connected to a network.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Save the sequence number of the broadcast AP link in the wlvif. For each
connected station, save the sequence number in the drv_priv part of
ieee80211_sta. Use the saved numbers on recovery/resume, with the
obligatory increment on recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Dont use free_sta() on AP global links. It would fail an internal check
within the function and various structures within the link struct would
not be reset.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Print board type, PG with metal and ROM versions.
This might help debugging HW related issues.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

For STA we report beacon loss to higher levels so that wpa_s
can attempt to roam without disconnecting. In case of P2P CLI
we don't want to attempt roaming and instead disconnect immediately
upon beacon loss.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>