- 08 Nov, 2017 14 commits
-
-
Kasin Li authored
commit 4a630fad upstream. In function submit_create, if nr_cmds or nr_bos is assigned with negative value, the allocated buffer may be small than intended. Using this buffer will lead to buffer overflow issue. Signed-off-by:
Kasin Li <donglil@codeaurora.org> Signed-off-by:
Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by:
Rob Clark <robdclark@gmail.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jani Nikula authored
commit 7c838e2a upstream. Per my reading of the eDP spec, DP_DPCD_DISPLAY_CONTROL_CAPABLE bit in DP_EDP_CONFIGURATION_CAP should be set if the eDP display control registers starting at offset DP_EDP_DPCD_REV are "enabled". Currently we check the bit before reading the registers, and DP_EDP_DPCD_REV is the only way to detect eDP revision. Turns out there are (likely buggy) displays that require eDP 1.4+ features, such as supported link rates and link rate select, but do not have the bit set. Read the display control registers unconditionally. They are supposed to read zero anyway if they are not supported, so there should be no harm in this. This fixes the referenced bug by enabling the eDP version check, and thus reading of the supported link rates. The panel in question has 0 in DP_MAX_LINK_RATE which is only supported in eDP 1.4+. Without the supported link rates method we default to RBR which is insufficient for the panel native mode. As a curiosity, the panel also has a bogus value of 0x12 in DP_EDP_DPCD_REV, but that passes our check for >= DP_EDP_14 (which is 0x03). Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103400Reported-and-tested-by:
Nicolas P. <issun.artiste@gmail.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171026142932.17737-1-jani.nikula@intel.com (cherry picked from commit 0501a3b0) Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Ashish Samant authored
commit 105ddc93 upstream. The first cluster group descriptor is not stored at the start of the group but at an offset from the start. We need to take this into account while doing fstrim on the first cluster group. Otherwise we will wrongly start fstrim a few blocks after the desired start block and the range can cross over into the next cluster group and zero out the group descriptor there. This can cause filesytem corruption that cannot be fixed by fsck. Link: http://lkml.kernel.org/r/1507835579-7308-1-git-send-email-ashish.samant@oracle.comSigned-off-by:
Ashish Samant <ashish.samant@oracle.com> Reviewed-by:
Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by:
Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Leo Liu authored
commit cb4b02d7 upstream. Fixes init failures on polaris cards with harvested UVD. Signed-off-by:
Leo Liu <leo.liu@amd.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Arnd Bergmann authored
commit 1cce91df upstream. The asm-generic/unaligned.h header provides two different implementations for accessing unaligned variables: the access_ok.h version used when CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set pretends that all pointers are in fact aligned, while the le_struct.h version convinces gcc that the alignment of a pointer is '1', to make it issue the correct load/store instructions depending on the architecture flags. On ARMv5 and older, we always use the second version, to let the compiler use byte accesses. On ARMv6 and newer, we currently use the access_ok.h version, so the compiler can use any instruction including stm/ldm and ldrd/strd that will cause an alignment trap. This trap can significantly impact performance when we have to do a lot of fixups and, worse, has led to crashes in the LZ4 decompressor code that does not have a trap handler. This adds an ARM specific version of asm/unaligned.h that uses the le_struct.h/be_struct.h implementation unconditionally. This should lead to essentially the same code on ARMv6+ as before, with the exception of using regular load/store instructions instead of the trapping instructions multi-register variants. The crash in the LZ4 decompressor code was probably introduced by the patch replacing the LZ4 implementation, commit 4e1a33b1 ("lib: update LZ4 compressor module"), so linux-4.11 and higher would be affected most. However, we probably want to have this backported to all older stable kernels as well, to help with the performance issues. There are two follow-ups that I think we should also work on, but not backport to stable kernels, first to change the asm-generic version of the header to remove the ARM special case, and second to review all other uses of CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to see if they might be affected by the same problem on ARM. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Julien Thierry authored
commit f9b269f3 upstream. When HYP code runs into branch profiling code, it attempts to jump to unmapped memory, causing a HYP Panic. Disable the branch profiling for code designed to run at HYP mode. Signed-off-by:
Julien Thierry <julien.thierry@arm.com> Acked-by:
Marc Zyngier <marc.zyngier@arm.com> Cc: Christoffer Dall <christoffer.dall@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
-
Dongjiu Geng authored
commit fd6c8c20 upstream. When a exception is trapped to EL2, hardware uses ELR_ELx to hold the current fault instruction address. If KVM wants to inject a abort to 32 bit guest, it needs to set the LR register for the guest to emulate this abort happened in the guest. Because ARM32 architecture is pipelined execution, so the LR value has an offset to the fault instruction address. The offsets applied to Link value for exceptions as shown below, which should be added for the ARM32 link register(LR). Table taken from ARMv8 ARM DDI0487B-B, table G1-10: Exception Offset, for PE state of: A32 T32 Undefined Instruction +4 +2 Prefetch Abort +4 +4 Data Abort +8 +8 IRQ or FIQ +4 +4 [ Removed unused variables in inject_abt to avoid compile warnings. -- Christoffer ] Signed-off-by:
Dongjiu Geng <gengdongjiu@huawei.com> Tested-by:
Haibin Zhang <zhanghaibin7@huawei.com> Reviewed-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
-
Mark Rutland authored
commit 7a7003b1 upstream. It's possible for a user to deliberately trigger __dump_instr with a chosen kernel address. Let's avoid problems resulting from this by using get_user() rather than __get_user(), ensuring that we don't erroneously access kernel memory. Where we use __dump_instr() on kernel text, we already switch to KERNEL_DS, so this shouldn't adversely affect those cases. Fixes: 60ffc30d ("arm64: Exception handling") Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Ricard Wanderlof authored
commit 1e6f4fc0 upstream. The ADC in the ADAU1361 (and possibly other Analog Devices codecs) exhibits a cyclic variation in the noise floor (in our test setup between -87 and -93 dB), a new value being attained within this range whenever a new capture stream is started. The cycle repeats after about 10 or 11 restarts. The workaround recommended by the manufacturer is to toggle the ADOSR bit in the Converter Control 0 register each time a new capture stream is started. I have verified that the patch fixes this problem on the ADAU1361, and according to the manufacturer toggling the bit in question in this manner will at least have no detrimental effect on other chips served by this driver. Signed-off-by:
Ricard Wanderlof <ricardw@axis.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Eric Biggers authored
commit 2eb9eabf upstream. syzkaller with KASAN reported an out-of-bounds read in asn1_ber_decoder(). It can be reproduced by the following command, assuming CONFIG_X509_CERTIFICATE_PARSER=y and CONFIG_KASAN=y: keyctl add asymmetric desc $'\x30\x30' @s The bug is that the length of an ASN.1 data value isn't validated in the case where it is encoded using the short form, causing the decoder to read past the end of the input buffer. Fix it by validating the length. The bug report was: BUG: KASAN: slab-out-of-bounds in asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233 Read of size 1 at addr ffff88003cccfa02 by task syz-executor0/6818 CPU: 1 PID: 6818 Comm: syz-executor0 Not tainted 4.14.0-rc7-00008-g5f479447 #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0xb3/0x10b lib/dump_stack.c:52 print_address_description+0x79/0x2a0 mm/kasan/report.c:252 kasan_report_error mm/kasan/report.c:351 [inline] kasan_report+0x236/0x340 mm/kasan/report.c:409 __asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:427 asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233 x509_cert_parse+0x1db/0x650 crypto/asymmetric_keys/x509_cert_parser.c:89 x509_key_preparse+0x64/0x7a0 crypto/asymmetric_keys/x509_public_key.c:174 asymmetric_key_preparse+0xcb/0x1a0 crypto/asymmetric_keys/asymmetric_type.c:388 key_create_or_update+0x347/0xb20 security/keys/key.c:855 SYSC_add_key security/keys/keyctl.c:122 [inline] SyS_add_key+0x1cd/0x340 security/keys/keyctl.c:62 entry_SYSCALL_64_fastpath+0x1f/0xbe RIP: 0033:0x447c89 RSP: 002b:00007fca7a5d3bd8 EFLAGS: 00000246 ORIG_RAX: 00000000000000f8 RAX: ffffffffffffffda RBX: 00007fca7a5d46cc RCX: 0000000000447c89 RDX: 0000000020006f4a RSI: 0000000020006000 RDI: 0000000020001ff5 RBP: 0000000000000046 R08: fffffffffffffffd R09: 0000000000000000 R10: 0000000000000002 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 00007fca7a5d49c0 R15: 00007fca7a5d4700 Fixes: 42d5ec27 ("X.509: Add an ASN.1 decoder") Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
Eric Biggers authored
commit 3239b6f2 upstream. Commit e645016a ("KEYS: fix writing past end of user-supplied buffer in keyring_read()") made keyring_read() stop corrupting userspace memory when the user-supplied buffer is too small. However it also made the return value in that case be the short buffer size rather than the size required, yet keyctl_read() is actually documented to return the size required. Therefore, switch it over to the documented behavior. Note that for now we continue to have it fill the short buffer, since it did that before (pre-v3.13) and dump_key_tree_aux() in keyutils arguably relies on it. Fixes: e645016a ("KEYS: fix writing past end of user-supplied buffer in keyring_read()") Reported-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ronnie Sahlberg authored
commit f74bc7c6 upstream. And fix tcon leak in error path. Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
Steve French <smfrench@gmail.com> Reviewed-by:
David Disseldorp <ddiss@samba.org> Signed-off-by:
-
Takashi Iwai authored
commit 1f20f9ff upstream. syzkaller reported the lockdep splat due to the possible deadlock of grp->list_mutex of each sequencer client object. Actually this is rather a false-positive report due to the missing nested lock annotations. The sequencer client may deliver the event directly to another client which takes another own lock. For addressing this issue, this patch replaces the simple down_read() with down_read_nested(). As a lock subclass, the already existing "hop" can be re-used, which indicates the depth of the call. Reference: http://lkml.kernel.org/r/089e082686ac9b482e055c832617@google.comReported-by:
syzbot <bot+7feb8de6b4d6bf810cf098bef942cc387e79d0ad@syzkaller.appspotmail.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 79fb0518 upstream. The races among ioctl and other operations were protected by the commit af368027 ("ALSA: timer: Fix race among timer ioctls") and later fixes, but one code path was forgotten in the scenario: the 32bit compat ioctl. As syzkaller recently spotted, a very similar use-after-free may happen with the combination of compat ioctls. The fix is simply to apply the same ioctl_lock to the compat_ioctl callback, too. Fixes: af368027 ("ALSA: timer: Fix race among timer ioctls") Reference: http://lkml.kernel.org/r/089e082686ac9b482e055c832617@google.comReported-by:
syzbot <bot+e5f3c9783e7048a74233054febbe9f1bdf54b6da@syzkaller.appspotmail.com> Signed-off-by:
-
- 02 Nov, 2017 24 commits
-
-
Greg Kroah-Hartman authored
-
Eric Biggers authored
commit f66665c0 upstream. In eCryptfs, we failed to verify that the authentication token keys are not revoked before dereferencing their payloads, which is problematic because the payload of a revoked key is NULL. request_key() *does* skip revoked keys, but there is still a window where the key can be revoked before we acquire the key semaphore. Fix it by updating ecryptfs_get_key_payload_data() to return -EKEYREVOKED if the key payload is NULL. For completeness we check this for "encrypted" keys as well as "user" keys, although encrypted keys cannot be revoked currently. Alternatively we could use key_validate(), but since we'll also need to fix ecryptfs_get_key_payload_data() to validate the payload length, it seems appropriate to just check the payload pointer. Fixes: 237fead6 ("[PATCH] ecryptfs: fs/Makefile and fs/Kconfig") Reviewed-by:
-
Guillaume Tucker authored
commit fc1111b8 upstream. The device tree nodes all correctly describe the regulators as syr827 or syr828, but the I2C device id is currently set to the wildcard value of syr82x in the driver. This causes udev to fail to match the driver module with the modalias data from sysfs. Fix this by replacing the I2C device ids with ones that match the device tree descriptions, with syr827 and syr828. Tested on Firefly rk3288 board. The syr82x id was not used anywhere. Fixes: e80c47bd (regulator: fan53555: Export I2C module alias information) Signed-off-by:
Guillaume Tucker <guillaume.tucker@collabora.com> Signed-off-by:
-
Herbert Xu authored
commit 1137b5e2 upstream. An independent security researcher, Mohamed Ghannam, has reported this vulnerability to Beyond Security's SecuriTeam Secure Disclosure program. The xfrm_dump_policy_done function expects xfrm_dump_policy to have been called at least once or it will crash. This can be triggered if a dump fails because the target socket's receive buffer is full. This patch fixes it by using the cb->start mechanism to ensure that the initialisation is always done regardless of the buffer situation. Fixes: 12a169e7 ("ipsec: Put dumpers on the dump list") Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Johannes Berg authored
commit 51e13359 upstream. If we try to connect while already connected/connecting, but this fails, we set ssid_len=0 but leave current_bss hanging, leading to errors. Check all of this better, first of all ensuring that we can't try to connect to a different SSID while connected/ing; ensure that prev_bssid is set for re-association attempts even in the case of the driver supporting the connect() method, and don't reset ssid_len in the failure cases. While at it, also reset ssid_len while disconnecting unless we were connected and expect a disconnected event, and warn on a successful connection without ssid_len being set. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Jimmy Assarsson authored
commit e1d2d132 upstream. To avoid kernel warning "Unhandled message (68)", ignore the CMD_FLUSH_QUEUE_REPLY message for now. As of Leaf v2 firmware version v4.1.844 (2017-02-15), flush tx queue is synchronous. There is a capability bit indicating whether flushing tx queue is synchronous or asynchronous. A proper solution would be to query the device for capabilities. If the synchronous tx flush capability bit is set, we should wait for CMD_FLUSH_QUEUE_REPLY message, while flushing the tx queue. Signed-off-by:
Jimmy Assarsson <jimmyassarsson@gmail.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Jimmy Assarsson authored
commit 8f65a923 upstream. If the return value from kvaser_usb_send_simple_msg() was non-zero, the return value from kvaser_usb_flush_queue() was printed in the kernel warning. Signed-off-by:
-
Gerhard Bertelsmann authored
commit 3a379f5b upstream. Fix loopback mode by setting the right flag and remove presume mode. Signed-off-by:
Gerhard Bertelsmann <info@gerhard-bertelsmann.de> Signed-off-by:
-
Rex Zhu authored
commit 8b95f4f7 upstream. refresh_rate was not initialized when program display gap. this patch can fix vce ring test failed when do S3 on Polaris10. bug: https://bugs.freedesktop.org/show_bug.cgi?id=103102 bug: https://bugzilla.kernel.org/show_bug.cgi?id=196615Reviewed-by:
Rex Zhu <Rex.Zhu@amd.com> Signed-off-by:
-
Ben Hutchings authored
commit 587c3c9f upstream. Commit 109bade9 ("scsi: sg: use standard lists for sg_requests") introduced an off-by-one error in sg_ioctl(), which was fixed by commit bd46fc40 ("scsi: sg: off by one in sg_ioctl()"). Unfortunately commit 4759df90 ("scsi: sg: factor out sg_fill_request_table()") moved that code, and reintroduced the bug (perhaps due to a botched rebase). Fix it again. Fixes: 4759df90 ("scsi: sg: factor out sg_fill_request_table()") Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Steffen Maier authored
commit ab31fd0c upstream. v4.10 commit 6f2ce1c6 ("scsi: zfcp: fix rport unblock race with LUN recovery") extended accessing parent pointer fields of struct zfcp_erp_action for tracing. If an erp_action has never been enqueued before, these parent pointer fields are uninitialized and NULL. Examples are zfcp objects freshly added to the parent object's children list, before enqueueing their first recovery subsequently. In zfcp_erp_try_rport_unblock(), we iterate such list. Accessing erp_action fields can cause a NULL pointer dereference. Since the kernel can read from lowcore on s390, it does not immediately cause a kernel page fault. Instead it can cause hangs on trying to acquire the wrong erp_action->adapter->dbf->rec_lock in zfcp_dbf_rec_action_lvl() ^bogus^ while holding already other locks with IRQs disabled. Real life example from attaching lots of LUNs in parallel on many CPUs: crash> bt 17723 PID: 17723 TASK: ... CPU: 25 COMMAND: "zfcperp0.0.1800" LOWCORE INFO: -psw : 0x0404300180000000 0x000000000038e424 -function : _raw_spin_lock_wait_flags at 38e424 ... #0 [fdde8fc90] zfcp_dbf_rec_action_lvl at 3e0004e9862 [zfcp] #1 [fdde8fce8] zfcp_erp_try_rport_unblock at 3e0004dfddc [zfcp] #2 [fdde8fd38] zfcp_erp_strategy at 3e0004e0234 [zfcp] #3 [fdde8fda8] zfcp_erp_thread at 3e0004e0a12 [zfcp] #4 [fdde8fe60] kthread at 173550 #5 [fdde8feb8] kernel_thread_starter at 10add2 zfcp_adapter zfcp_port zfcp_unit <address>, 0x404040d600000000 scsi_device NULL, returning early! zfcp_scsi_dev.status = 0x40000000 0x40000000 ZFCP_STATUS_COMMON_RUNNING crash> zfcp_unit <address> struct zfcp_unit { erp_action = { adapter = 0x0, port = 0x0, unit = 0x0, }, } zfcp_erp_action is always fully embedded into its container object. Such container object is never moved in its object tree (only add or delete). Hence, erp_action parent pointers can never change. To fix the issue, initialize the erp_action parent pointers before adding the erp_action container to any list and thus before it becomes accessible from outside of its initializing function. In order to also close the time window between zfcp_erp_setup_act() memsetting the entire erp_action to zero and setting the parent pointers again, drop the memset and instead explicitly initialize individually all erp_action fields except for parent pointers. To be extra careful not to introduce any other unintended side effect, even keep zeroing the erp_action fields for list and timer. Also double-check with WARN_ON_ONCE that erp_action parent pointers never change, so we get to know when we would deviate from previous behavior. Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 6f2ce1c6 ("scsi: zfcp: fix rport unblock race with LUN recovery") Reviewed-by:
Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by:
-
David Howells authored
commit ea678998 upstream. This fixes CVE-2017-12193. Fix a case in the assoc_array implementation in which a new leaf is added that needs to go into a node that happens to be full, where the existing leaves in that node cluster together at that level to the exclusion of new leaf. What needs to happen is that the existing leaves get moved out to a new node, N1, at level + 1 and the existing node needs replacing with one, N0, that has pointers to the new leaf and to N1. The code that tries to do this gets this wrong in two ways: (1) The pointer that should've pointed from N0 to N1 is set to point recursively to N0 instead. (2) The backpointer from N0 needs to be set correctly in the case N0 is either the root node or reached through a shortcut. Fix this by removing this path and using the split_node path instead, which achieves the same end, but in a more general way (thanks to Eric Biggers for spotting the redundancy). The problem manifests itself as: BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 IP: assoc_array_apply_edit+0x59/0xe5 Fixes: 3cb98950 ("Add a generic associative array implementation.") Reported-and-tested-by:
WU Fan <u3536072@connect.hku.hk> Signed-off-by:
-
Dmitry Torokhov authored
commit a5082947 upstream. parse_hid_report_descriptor() has a while (i < length) loop, which only guarantees that there's at least 1 byte in the buffer, but the loop body can read multiple bytes which causes out-of-bounds access. Reported-by:
Andrey Konovalov <andreyknvl@google.com> Reviewed-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 57a95b41 upstream. ELAN0611 touchpad uses elan_i2c as its driver. It can be found on Lenovo ideapad 320-15IKB. So add it to ACPI table to enable the touchpad. [Ido Adiv <idoad123@gmail.com> reports that the same ACPI ID is used for Elan touchpad in ideapad 520]. BugLink: https://bugs.launchpad.net/bugs/1723736Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Juergen Gross authored
commit 298d275d upstream. In case gntdev_mmap() succeeds only partially in mapping grant pages it will leave some vital information uninitialized needed later for cleanup. This will lead to an out of bounds array access when unmapping the already mapped pages. So just initialize the data needed for unmapping the pages a little bit earlier. Reported-by:
Arthur Borsboom <arthurborsboom@gmail.com> Signed-off-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
-
Miklos Szeredi authored
commit c6cdd514 upstream. Marios Titas running a Haskell program noticed a problem with fuse's readdirplus: when it is interrupted by a signal, it skips one directory entry. The reason is that fuse erronously updates ctx->pos after a failed dir_emit(). The issue originates from the patch adding readdirplus support. Reported-by:
Jakob Unterwurzacher <jakobunt@gmail.com> Tested-by:
Marios Titas <redneb@gmx.com> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Fixes: 0b05b183 ("fuse: implement NFS-like readdirplus support") Signed-off-by:
-
Florian Fainelli authored
commit c0368e4d upstream. There was an inversion in how the error path in bcm_qspi_probe() is done which would make us trip over a KASAN use-after-free report. Turns out that qspi->dev_ids does not get allocated until later in the probe process. Fix this by introducing a new lable: qspi_resource_err which takes care of cleaning up the SPI master instance. Fixes: fa236a7e ("spi: bcm-qspi: Add Broadcom MSPI driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Baruch Siach authored
commit a2b4a79b upstream. The SPI_IOC_MESSAGE() macro references _IOC_SIZEBITS. Add linux/ioctl.h to make sure this macro is defined. This fixes the following build failure of lcdproc with the musl libc: In file included from .../sysroot/usr/include/sys/ioctl.h:7:0, from hd44780-spi.c:31: hd44780-spi.c: In function 'spi_transfer': hd44780-spi.c:89:24: error: '_IOC_SIZEBITS' undeclared (first use in this function) status = ioctl(p->fd, SPI_IOC_MESSAGE(1), &xfer); ^ Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
-
Greg Kurz authored
commit ac64115a upstream. The following program causes a kernel oops: #include <sys/types.h> #include <sys/stat.h> #include <fcntl.h> #include <sys/ioctl.h> #include <linux/kvm.h> main() { int fd = open("/dev/kvm", O_RDWR); ioctl(fd, KVM_CHECK_EXTENSION, KVM_CAP_PPC_HTM); } This happens because when using the global KVM fd with KVM_CHECK_EXTENSION, kvm_vm_ioctl_check_extension() gets called with a NULL kvm argument, which gets dereferenced in is_kvmppc_hv_enabled(). Spotted while reading the code. Let's use the hv_enabled fallback variable, like everywhere else in this function. Fixes: 23528bb2 ("KVM: PPC: Introduce KVM_CAP_PPC_HTM") Signed-off-by:
Greg Kurz <groug@kaod.org> Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Reviewed-by:
Thomas Huth <thuth@redhat.com> Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Mayank Rana authored
commit b3207c65 upstream. xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times without checking the return value. xhci_queue_stop_endpoint() can return error if the HC is already halted or unable to queue commands. This can cause a deadlock condition as xhci_stop_device() would end up waiting indefinitely for a completion for the command that didn't get queued. Fix this by checking the return value and bailing out of xhci_stop_device() in case of error. This patch happens to fix potential memory leaks of the allocated command structures as well. Fixes: c311e391 ("xhci: rework command timeout and cancellation,") Signed-off-by:
Mayank Rana <mrana@codeaurora.org> Signed-off-by:
Jack Pham <jackp@codeaurora.org> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Jeff Layton authored
commit 6c2838fb upstream. sparse warns: fs/ceph/caps.c:2042:9: warning: context imbalance in 'try_flush_caps' - wrong count at exit We need to exit this function with the lock unlocked, but a couple of cases leave it locked. Signed-off-by:
Jeff Layton <jlayton@redhat.com> Reviewed-by:
"Yan, Zheng" <zyan@redhat.com> Reviewed-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Hui Wang authored
commit f265788c upstream. We have several Dell laptops which use the codec alc236, the headset mic can't work on these machines. Following the commit 736f20a7, we add the pin cfg table to make the headset mic work. Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
Kailang Yang authored
commit 736f20a7 upstream. Add support for ALC236/ALC3204. Add headset mode support for ALC236/ALC3204. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
-
Tejun Heo authored
commit 692b4825 upstream. Josef reported a HARDIRQ-safe -> HARDIRQ-unsafe lock order detected by lockdep: [ 1270.472259] WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected [ 1270.472783] 4.14.0-rc1-xfstests-12888-g76833e8 #110 Not tainted [ 1270.473240] ----------------------------------------------------- [ 1270.473710] kworker/u5:2/5157 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 1270.474239] (&(&lock->wait_lock)->rlock){+.+.}, at: [<ffffffff8da253d2>] __mutex_unlock_slowpath+0xa2/0x280 [ 1270.474994] [ 1270.474994] and this task is already holding: [ 1270.475440] (&pool->lock/1){-.-.}, at: [<ffffffff8d2992f6>] worker_thread+0x366/0x3c0 [ 1270.476046] which would create a new lock dependency: [ 1270.476436] (&pool->lock/1){-.-.} -> (&(&lock->wait_lock)->rlock){+.+.} [ 1270.476949] [ 1270.476949] but this new dependency connects a HARDIRQ-irq-safe lock: [ 1270.477553] (&pool->lock/1){-.-.} ... [ 1270.488900] to a HARDIRQ-irq-unsafe lock: [ 1270.489327] (&(&lock->wait_lock)->rlock){+.+.} ... [ 1270.494735] Possible interrupt unsafe locking scenario: [ 1270.494735] [ 1270.495250] CPU0 CPU1 [ 1270.495600] ---- ---- [ 1270.495947] lock(&(&lock->wait_lock)->rlock); [ 1270.496295] local_irq_disable(); [ 1270.496753] lock(&pool->lock/1); [ 1270.497205] lock(&(&lock->wait_lock)->rlock); [ 1270.497744] <Interrupt> [ 1270.497948] lock(&pool->lock/1); , which will cause a irq inversion deadlock if the above lock scenario happens. The root cause of this safe -> unsafe lock order is the mutex_unlock(pool->manager_arb) in manage_workers() with pool->lock held. Unlocking mutex while holding an irq spinlock was never safe and this problem has been around forever but it never got noticed because the only time the mutex is usually trylocked while holding irqlock making actual failures very unlikely and lockdep annotation missed the condition until the recent b9c16a0e ("locking/mutex: Fix lockdep_assert_held() fail"). Using mutex for pool->manager_arb has always been a bit of stretch. It primarily is an mechanism to arbitrate managership between workers which can easily be done with a pool flag. The only reason it became a mutex is that pool destruction path wants to exclude parallel managing operations. This patch replaces the mutex with a new pool flag POOL_MANAGER_ACTIVE and make the destruction path wait for the current manager on a wait queue. v2: Drop unnecessary flag clearing before pool destruction as suggested by Boqun. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Josef Bacik <josef@toxicpanda.com> Reviewed-by:
Lai Jiangshan <jiangshanlai@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Boqun Feng <boqun.feng@gmail.com> Signed-off-by:
-
- 27 Oct, 2017 2 commits
-
-
Greg Kroah-Hartman authored
-
Eric Biggers authored
commit d124b2c5 upstream. When the file /proc/fs/fscache/objects (available with CONFIG_FSCACHE_OBJECT_LIST=y) is opened, we request a user key with description "fscache:objlist", then access its payload. However, a revoked key has a NULL payload, and we failed to check for this. request_key() *does* skip revoked keys, but there is still a window where the key can be revoked before we access its payload. Fix it by checking for a NULL payload, treating it like a key which was already revoked at the time it was requested. Fixes: 4fbf4291 ("FS-Cache: Allow the current state of all objects to be dumped") Reviewed-by:
-
