- 20 May, 2015 40 commits
-
-
Boris Ostrovsky authored
commit 5cec9883 upstream. When a guest is resumed, the hypervisor may change event channel assignments. If this happens and the guest uses 2-level events it is possible for the interrupt to be claimed by wrong VCPU since cpu_evtchn_mask bits may be stale. This can happen even though evtchn_2l_bind_to_cpu() attempts to clear old bits: irq_info that is passed in is not necessarily the original one (from pre-migration times) but instead is freshly allocated during resume and so any information about which CPU the channel was bound to is lost. Thus we should clear the mask during resume. We also need to make sure that bits for xenstore and console channels are set when these two subsystems are resumed. While rebind_evtchn_irq() (which is invoked for both of them on a resume) calls irq_set_affinity(), the latter will in fact postpone setting affinity until handling the interrupt. But because cpu_evtchn_mask will have bits for these two cleared we won't be able to take the interrupt. With that in mind, we need to bind those two channels explicitly in rebind_evtchn_irq(). We will keep irq_set_affinity() so that we have a pass through generic irq affinity code later, in case something needs to be updated there as well. (Also replace cpumask_of(0) with cpumask_of(info->cpu) in rebind_evtchn_irq(): it should be set to zero in preceding xen_irq_info_evtchn_setup().) Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Reported-by:
Annie Li <annie.li@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Dan Carpenter authored
commit d67e1996 upstream. I spotted two (difficult to hit) bugs while reviewing this. 1) There is a double free bug because we unregister "map_kset" in add_sysfs_runtime_map_entry() and also efi_runtime_map_init(). 2) If we fail to allocate "entry" then we should return ERR_PTR(-ENOMEM) instead of NULL. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Dave Young <dyoung@redhat.com> Cc: Guangyu Sun <guangyu.sun@oracle.com> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
Lukas Wunner authored
commit 3916e3fd upstream. Single channel LVDS maxes out at 112 MHz. The 15" pre-retina models shipped with 1440x900 (106 MHz) by default or 1680x1050 (119 MHz) as a BTO option, both versions used dual channel LVDS even though the smaller one would have fit into a single channel. Notes: Bug report showing that the MacBookPro8,2 with 1440x900 uses dual channel LVDS (this lead to it being hardcoded in intel_lvds.c by Daniel Vetter with commit 618563e3): https://bugzilla.kernel.org/show_bug.cgi?id=42842 If i915.lvds_channel_mode=2 is missing even though the machine needs it, every other vertical line is white and consequently, only the left half of the screen is visible (verified by myself on a MacBookPro9,1). Forum posting concerning a MacBookPro6,2 with 1440x900, author is using i915.lvds_channel_mode=2 on the kernel command line, proving that the machine uses dual channels: https://bbs.archlinux.org/viewtopic.php?id=185770 Chi Mei N154C6-L04 with 1440x900 is a replacement panel for all MacBook Pro "A1286" models, and that model number encompasses the MacBookPro6,2 / 8,2 / 9,1. Page 17 of the panel's datasheet shows it's driven with dual channel LVDS: http://www.ebay.com/itm/-/400690878560 http://www.everymac.com/ultimate-mac-lookup/?search_keywords=A1286 http://www.taopanel.com/chimei/datasheet/N154C6-L04.pdf Those three 15" models, MacBookPro6,2 / 8,2 / 9,1, are the only ones with i915 graphics and dual channel LVDS, so that list should be complete. And the 8,2 is already in intel_lvds.c. Possible motivation to use dual channel LVDS even on the 1440x900 models: Reduce the number of different parts, i.e. use identical logic boards and display cabling on both versions and the only differing component is the panel. Signed-off-by:
Lukas Wunner <lukas@wunner.de> Acked-by:
Jani Nikula <jani.nikula@intel.com> [Jani: included notes in the commit message for posterity] Signed-off-by:
-
Jason Gunthorpe authored
commit 28521440 upstream. When accepting a new IPv4 connect to an IPv6 socket, the CMA tries to canonize the address family to IPv4, but does not properly process the listening sockaddr to get the listening port, and does not properly set the address family of the canonized sockaddr. Fixes: e51060f0 ("IB: IP address based RDMA connection manager") Reported-By:
Yotam Kenneth <yotamke@mellanox.com> Signed-off-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Tested-by:
Haggai Eran <haggaie@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Christian König authored
commit 013ead48 upstream. Hardware doesn't seem to work correctly, just block userspace in this case. v2: add missing defines Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=85320Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Pavel Machek authored
commit 1819e303 upstream. N900 audio recording needs that codec provides bias voltage for integrated digital microphone and headset microphone depending which one is used. Digital microphone uses 2 V bias and it comes from the codec A part. Codec B part drives the headset microphone bias and that is set to 2.5 V. Signed-off-by:
Pavel Machek <pavel@ucw.cz> [Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit e2e8bfdf ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")] Signed-off-by:
Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Tony Lindgren authored
commit 102bcb6e upstream. If we use a combination of VMODE and I2C4 for retention modes, eventually the off idle power consumption will creep up by about 23mW, even during off mode with I2C4 always staying enabled. Turns out this is because of erratum i531 "Extra Power Consumed When Repeated Start Operation Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)" as pointed out by Nishanth Menon <nm@ti.com>. Let's fix the issue by adding i2c_cfg_clear_mask for the bits to clear when initializing the I2C4 adapter so we can clear SREN bit that drives the I2C4 lines low otherwise when there is no traffic. Fixes: 3b8c4ebb ("ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode") Cc: Kevin Hilman <khilman@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Reviewed-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
-
Witold Szczeponik authored
commit 622532bb upstream. Commit eec15edb (ACPI / PNP: use device ID list for PNPACPI device enumeration) changed the way how ACPI devices are enumerated and when they are added to the PNP bus. However, it broke the sound card support on (at least) a vintage IBM ThinkPad 600E: with said commit applied, two of the necessary "CSC01xx" devices are not added to the PNP bus and hence can not be found during the initialization of the "snd-cs4236" module. As a consequence, loading "snd-cs4236" causes null pointer exceptions. The attached patch fixes the problem end re-enables sound on the IBM ThinkPad 600E. Fixes: eec15edb (ACPI / PNP: use device ID list for PNPACPI device enumeration) Signed-off-by:
Witold Szczeponik <Witold.Szczeponik@gmx.net> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Johan Hovold authored
commit 483d8211 upstream. Unregister GPIOs requested through sysfs at chip remove to avoid leaking the associated memory and sysfs entries. The stale sysfs entries prevented the gpio numbers from being exported when the gpio range was later reused (e.g. at device reconnect). This also fixes the related module-reference leak. Note that kernfs makes sure that any on-going sysfs operations finish before the class devices are unregistered and that further accesses fail. The chip exported flag is used to prevent gpiod exports during removal. This also makes it harder to trigger, but does not fix, the related race between gpiochip_remove and export_store, which is really a race with gpiod_request that needs to be addressed separately. Also note that this would prevent the crashes (e.g. NULL-dereferences) at reconnect that affects pre-3.18 kernels, as well as use-after-free on operations on open attribute files on pre-3.14 kernels (prior to kernfs). Fixes: d8f388d8 ("gpio: sysfs interface") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [ luis: backported to 3.16: - file rename: drivers/gpio/gpiolib-sysfs.c -> drivers/gpio/gpiolib.c ] Signed-off-by:
-
Johan Hovold authored
commit 01cca93a upstream. Unregister gpiochip device (used to export information through sysfs) before removing it internally. This way removal will reverse addition. Signed-off-by:
-
Marek Vasut authored
commit 4ada77e3 upstream. Fix a typo in the TX DMA interrupt name for AUART4. This patch makes AUART4 operational again. Signed-off-by:
Marek Vasut <marex@denx.de> Fixes: f30fb03d ("ARM: dts: add generic DMA device tree binding for mxs-dma") Acked-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Markus Pargmann authored
commit f90d3f0d upstream. The property '#pwm-cells' is currently missing. It is not possible to use pwm4 without this property. Signed-off-by:
Markus Pargmann <mpa@pengutronix.de> Fixes: 5658a68f ("ARM i.MX25: Add devicetree") Reviewed-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Philipp Zabel authored
commit 7f8d49dc upstream. The fixed-regulator bindings require a separate property enable-active-high, the standard gpio phandle property polarity setting is ignored. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Fixes: 4fe69a93 ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo") Signed-off-by:
-
Stefan Wahren authored
commit 0fdebe1a upstream. The dr_mode of usb0 on imx233-olinuxino is left to default "otg". Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the same pin as USB_OTG_ID it's possible to disable USB host by LED toggling: echo 0 > /sys/class/leds/green/brightness [ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1 [ 1068.890000] usb usb1: USB disconnect, device number 1 [ 1068.920000] usb 1-1: USB disconnect, device number 2 [ 1068.920000] usb 1-1.1: USB disconnect, device number 3 [ 1069.070000] usb 1-1.2: USB disconnect, device number 4 [ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered [ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11 This patch fixes the issue by setting dr_mode to "host" in the dts file. Reported-by:
Harald Geyer <harald@ccbib.org> Signed-off-by:
Peter Chen <peter.chen@freescale.com> Fixes: b4931294 ("ARM: dts: imx23-olinuxino: Add USB host support") Signed-off-by:
-
Fabio Estevam authored
commit cfe8c597 upstream. On imx23-olinuxino the LED turns on when level logic high is aplied to GPIO2_1. Fix the gpios property accordingly. Fixes: b34aa185 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"") Reported-by:
-
Gregory CLEMENT authored
commit 750e30d4 upstream. There is no crystal connected to the internal RTC on the Open Block AX3. So let's disable it in order to prevent the kernel probing the driver uselessly. Eventually this patches removes the following warning message from the boot log: "rtc-mv d0010300.rtc: internal RTC not ticking" Acked-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Tejun Heo authored
commit 464d1387 upstream. mm/page-writeback.c has several places where 1 is added to the divisor to prevent division by zero exceptions; however, if the original divisor is equivalent to -1, adding 1 leads to division by zero. There are three places where +1 is used for this purpose - one in pos_ratio_polynom() and two in bdi_position_ratio(). The second one in bdi_position_ratio() actually triggered div-by-zero oops on a machine running a 3.10 kernel. The divisor is x_intercept - bdi_setpoint + 1 == span + 1 span is confirmed to be (u32)-1. It isn't clear how it ended up that but it could be from write bandwidth calculation underflow fixed by c72efb65 ("writeback: fix possible underflow in write bandwidth calculation"). At any rate, +1 isn't a proper protection against div-by-zero. This patch converts all +1 protections to |1. Note that bdi_update_dirty_ratelimit() was already using |1 before this patch. Signed-off-by:
Tejun Heo <tj@kernel.org> Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Ming Lei authored
commit 2a34c087 upstream. hctx->tags has to be set as NULL in case that it is to be unmapped no matter if set->tags[hctx->queue_num] is NULL or not in blk_mq_map_swqueue() because shared tags can be freed already from another request queue. The same situation has to be considered during handling CPU online too. Unmapped hw queue can be remapped after CPU topo is changed, so we need to allocate tags for the hw queue in blk_mq_map_swqueue(). Then tags allocation for hw queue can be removed in hctx cpu online notifier, and it is reasonable to do that after mapping is updated. Reported-by:
Dongsu Park <dongsu.park@profitbricks.com> Tested-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
-
Roy Franz authored
commit 98b228f5 upstream. Until now, the EFI stub was only setting the 32 bit cmd_line_ptr in the setup_header structure, so on 64 bit platforms this could be truncated. This patch adds setting the upper bits of the buffer address in ext_cmd_line_ptr. This case was likely never hit, as the allocation for this buffer is done at the lowest available address. Only x86_64 kernels have this problem, as the 1-1 mapping mandated by EFI ensures that all memory is 32 bit addressable on 32 bit platforms. The EFI stub does not support mixed mode, so the 32 bit kernel on 64 bit firmware case does not need to be handled. Signed-off-by:
Roy Franz <roy.franz@linaro.org> Signed-off-by:
-
Ross Lagerwall authored
commit c57dcb56 upstream. Some buggy firmware implementations update VariableNameSize on success such that it does not include the final NUL character which results in garbage in the efivarfs name entries. Use kzalloc on the efivar_entry (as is done in efivars.c) to ensure that the name is always NUL-terminated. The buggy firmware is: BIOS Information Vendor: Intel Corp. Version: S1200RP.86B.02.02.0005.102320140911 Release Date: 10/23/2014 BIOS Revision: 4.6 System Information Manufacturer: Intel Corporation Product Name: S1200RP_SE Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by:
Matthew Garrett <mjg59@coreos.com> Cc: Jeremy Kerr <jk@ozlabs.org> Signed-off-by:
-
Florian Westphal authored
commit 330966e5 upstream. skb_gso_segment has three possible return values: 1. a pointer to the first segmented skb 2. an errno value (IS_ERR()) 3. NULL. This can happen when GSO is used for header verification. However, several callers currently test IS_ERR instead of IS_ERR_OR_NULL and would oops when NULL is returned. Note that these call sites should never actually see such a NULL return value; all callers mask out the GSO bits in the feature argument. However, there have been issues with some protocol handlers erronously not respecting the specified feature mask in some cases. It is preferable to get 'have to turn off hw offloading, else slow' reports rather than 'kernel crashes'. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Christoffer Dall authored
commit ae705930 upstream. There is an interesting bug in the vgic code, which manifests itself when the KVM run loop has a signal pending or needs a vmid generation rollover after having disabled interrupts but before actually switching to the guest. In this case, we flush the vgic as usual, but we sync back the vgic state and exit to userspace before entering the guest. The consequence is that we will be syncing the list registers back to the software model using the GICH_ELRSR and GICH_EISR from the last execution of the guest, potentially overwriting a list register containing an interrupt. This showed up during migration testing where we would capture a state where the VM has masked the arch timer but there were no interrupts, resulting in a hung test. Cc: Marc Zyngier <marc.zyngier@arm.com> Reported-by:
Alex Bennee <alex.bennee@linaro.org> Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Shannon Zhao <shannon.zhao@linaro.org> [ luis: backported to 3.16: used shannon's backport to 3.14 ] Signed-off-by:
-
Marc Zyngier authored
commit 04b8dc85 upstream. The kernel's pgd_index macro is designed to index a normal, page sized array. KVM is a bit diffferent, as we can use concatenated pages to have a bigger address space (for example 40bit IPA with 4kB pages gives us an 8kB PGD. In the above case, the use of pgd_index will always return an index inside the first 4kB, which makes a guest that has memory above 0x8000000000 rather unhappy, as it spins forever in a page fault, whist the host happilly corrupts the lower pgd. The obvious fix is to get our own kvm_pgd_index that does the right thing(tm). Tested on X-Gene with a hacked kvmtool that put memory at a stupidly high address. Reviewed-by:
-
Marc Zyngier authored
commit 801f6772 upstream. Commit b856a591 (arm/arm64: KVM: Reset the HCR on each vcpu when resetting the vcpu) moved the init of the HCR register to happen later in the init of a vcpu, but left out the fixup done in kvm_reset_vcpu when preparing for a 32bit guest. As a result, the 32bit guest is run as a 64bit guest, but the rest of the kernel still manages it as a 32bit. Fun follows. Moving the fixup to vcpu_reset_hcr solves the problem for good. Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Marc Zyngier authored
commit 55e858b7 upstream. It took about two years for someone to notice that the IPA passed to TLBI IPAS2E1IS must be shifted by 12 bits. Clearly our reviewing is not as good as it should be... Paper bag time for me. Reported-by:
Mario Smarduch <m.smarduch@samsung.com> Tested-by:
-
Christoffer Dall authored
commit 05971120 upstream. It is curently possible to run a VM with architected timers support without creating an in-kernel VGIC, which will result in interrupts from the virtual timer going nowhere. To address this issue, move the architected timers initialization to the time when we run a VCPU for the first time, and then only initialize (and enable) the architected timers if we have a properly created and initialized in-kernel VGIC. When injecting interrupts from the virtual timer to the vgic, the current setup should ensure that this never calls an on-demand init of the VGIC, which is the only call path that could return an error from kvm_vgic_inject_irq(), so capture the return value and raise a warning if there's an error there. We also change the kvm_timer_init() function from returning an int to be a void function, since the function always succeeds. Reviewed-by:
-
Christoffer Dall authored
commit 716139df upstream. When the vgic initializes its internal state it does so based on the number of VCPUs available at the time. If we allow KVM to create more VCPUs after the VGIC has been initialized, we are likely to error out in unfortunate ways later, perform buffer overflows etc. Acked-by:
Eric Auger <eric.auger@linaro.org> Signed-off-by:
-
Christoffer Dall authored
commit 957db105 upstream. Introduce a new function to unmap user RAM regions in the stage2 page tables. This is needed on reboot (or when the guest turns off the MMU) to ensure we fault in pages again and make the dcache, RAM, and icache coherent. Using unmap_stage2_range for the whole guest physical range does not work, because that unmaps IO regions (such as the GIC) which will not be recreated or in the best case faulted in on a page-by-page basis. Call this function on secondary and subsequent calls to the KVM_ARM_VCPU_INIT ioctl so that a reset VCPU will detect the guest Stage-1 MMU is off when faulting in pages and make the caches coherent. Acked-by:
-
Christoffer Dall authored
commit b856a591 upstream. When userspace resets the vcpu using KVM_ARM_VCPU_INIT, we should also reset the HCR, because we now modify the HCR dynamically to enable/disable trapping of guest accesses to the VM registers. This is crucial for reboot of VMs working since otherwise we will not be doing the necessary cache maintenance operations when faulting in pages with the guest MMU off. Acked-by:
-
Christoffer Dall authored
commit 3ad8b3de upstream. The implementation of KVM_ARM_VCPU_INIT is currently not doing what userspace expects, namely making sure that a vcpu which may have been turned off using PSCI is returned to its initial state, which would be powered on if userspace does not set the KVM_ARM_VCPU_POWER_OFF flag. Implement the expected functionality and clarify the ABI. Acked-by:
-
Christoffer Dall authored
commit 03f1d4c1 upstream. If a VCPU was originally started with power off (typically to be brought up by PSCI in SMP configurations), there is no need to clear the POWER_OFF flag in the kernel, as this flag is only tested during the init ioctl itself. Acked-by:
-
Ard Biesheuvel authored
commit 07a9748c upstream. Instead of using kvm_is_mmio_pfn() to decide whether a host region should be stage 2 mapped with device attributes, add a new static function kvm_is_device_pfn() that disregards RAM pages with the reserved bit set, as those should usually not be mapped as device memory. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
-
Geoff Levand authored
commit 286fb1cc upstream. Some of the macros defined in kvm_arm.h are useful in assembly files, but are not compatible with the assembler. Change any C language integer constant definitions using appended U, UL, or ULL to the UL() preprocessor macro. Also, add a preprocessor include of the asm/memory.h file which defines the UL() macro. Fixes build errors like these when using kvm_arm.h in assembly source files: Error: unexpected characters following instruction at operand 3 -- `and x0,x1,#((1U<<25)-1)' Acked-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Geoff Levand <geoff@infradead.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Christoffer Dall authored
commit 6b50f540 upstream. If we detect another vCPU is running we just exit and return 0 as if we succesfully created the VGIC, but the VGIC wouldn't actual be created. This shouldn't break in-kernel behavior because the kernel will not observe the failed the attempt to create the VGIC, but userspace could be rightfully confused. Cc: Andre Przywara <andre.przywara@arm.com> Signed-off-by:
-
Mark Rutland authored
commit 7cbb87d6 upstream. Currently if using a 48-bit VA, tearing down the hyp page tables (which can happen in the absence of a GICH or GICV resource) results in the rather nasty splat below, evidently becasue we access a table that doesn't actually exist. Commit 38f791a4 (arm64: KVM: Implement 48 VA support for KVM EL2 and Stage-2) added a pgd_none check to __create_hyp_mappings to account for the additional level of tables, but didn't add a corresponding check to unmap_range, and this seems to be the source of the problem. This patch adds the missing pgd_none check, ensuring we don't try to access tables that don't exist. Original splat below: kvm [1]: Using HYP init bounce page @83fe94a000 kvm [1]: Cannot obtain GICH resource Unable to handle kernel paging request at virtual address ffff7f7fff000000 pgd = ffff800000770000 [ffff7f7fff000000] *pgd=0000000000000000 Internal error: Oops: 96000004 [#1] PREEMPT SMP Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc2+ #89 task: ffff8003eb500000 ti: ffff8003eb45c000 task.ti: ffff8003eb45c000 PC is at unmap_range+0x120/0x580 LR is at free_hyp_pgds+0xac/0xe4 pc : [<ffff80000009b768>] lr : [<ffff80000009cad8>] pstate: 80000045 sp : ffff8003eb45fbf0 x29: ffff8003eb45fbf0 x28: ffff800000736000 x27: ffff800000735000 x26: ffff7f7fff000000 x25: 0000000040000000 x24: ffff8000006f5000 x23: 0000000000000000 x22: 0000007fffffffff x21: 0000800000000000 x20: 0000008000000000 x19: 0000000000000000 x18: ffff800000648000 x17: ffff800000537228 x16: 0000000000000000 x15: 000000000000001f x14: 0000000000000000 x13: 0000000000000001 x12: 0000000000000020 x11: 0000000000000062 x10: 0000000000000006 x9 : 0000000000000000 x8 : 0000000000000063 x7 : 0000000000000018 x6 : 00000003ff000000 x5 : ffff800000744188 x4 : 0000000000000001 x3 : 0000000040000000 x2 : ffff800000000000 x1 : 0000007fffffffff x0 : 000000003fffffff Process swapper/0 (pid: 1, stack limit = 0xffff8003eb45c058) Stack: (0xffff8003eb45fbf0 to 0xffff8003eb460000) fbe0: eb45fcb0 ffff8003 0009cad8 ffff8000 fc00: 00000000 00000080 00736140 ffff8000 00736000 ffff8000 00000000 00007c80 fc20: 00000000 00000080 006f5000 ffff8000 00000000 00000080 00743000 ffff8000 fc40: 00735000 ffff8000 006d3030 ffff8000 006fe7b8 ffff8000 00000000 00000080 fc60: ffffffff 0000007f fdac1000 ffff8003 fd94b000 ffff8003 fda47000 ffff8003 fc80: 00502b40 ffff8000 ff000000 ffff7f7f fdec6000 00008003 fdac1630 ffff8003 fca0: eb45fcb0 ffff8003 ffffffff 0000007f eb45fd00 ffff8003 0009b378 ffff8000 fcc0: ffffffea 00000000 006fe000 ffff8000 00736728 ffff8000 00736120 ffff8000 fce0: 00000040 00000000 00743000 ffff8000 006fe7b8 ffff8000 0050cd48 00000000 fd00: eb45fd60 ffff8003 00096070 ffff8000 006f06e0 ffff8000 006f06e0 ffff8000 fd20: fd948b40 ffff8003 0009a320 ffff8000 00000000 00000000 00000000 00000000 fd40: 00000ae0 00000000 006aa25c ffff8000 eb45fd60 ffff8003 0017ca44 00000002 fd60: eb45fdc0 ffff8003 0009a33c ffff8000 006f06e0 ffff8000 006f06e0 ffff8000 fd80: fd948b40 ffff8003 0009a320 ffff8000 00000000 00000000 00735000 ffff8000 fda0: 006d3090 ffff8000 006aa25c ffff8000 00735000 ffff8000 006d3030 ffff8000 fdc0: eb45fdd0 ffff8003 000814c0 ffff8000 eb45fe50 ffff8003 006aaac4 ffff8000 fde0: 006ddd90 ffff8000 00000006 00000000 006d3000 ffff8000 00000095 00000000 fe00: 006a1e90 ffff8000 00735000 ffff8000 006d3000 ffff8000 006aa25c ffff8000 fe20: 00735000 ffff8000 006d3030 ffff8000 eb45fe50 ffff8003 006fac68 ffff8000 fe40: 00000006 00000006 fe293ee6 ffff8003 eb45feb0 ffff8003 004f8ee8 ffff8000 fe60: 004f8ed4 ffff8000 00735000 ffff8000 00000000 00000000 00000000 00000000 fe80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 fea0: 00000000 00000000 00000000 00000000 00000000 00000000 000843d0 ffff8000 fec0: 004f8ed4 ffff8000 00000000 00000000 00000000 00000000 00000000 00000000 fee0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ff00: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ff20: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ff40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ff60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ff80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffa0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000005 00000000 ffe0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 Call trace: [<ffff80000009b768>] unmap_range+0x120/0x580 [<ffff80000009cad4>] free_hyp_pgds+0xa8/0xe4 [<ffff80000009b374>] kvm_arch_init+0x268/0x44c [<ffff80000009606c>] kvm_init+0x24/0x260 [<ffff80000009a338>] arm_init+0x18/0x24 [<ffff8000000814bc>] do_one_initcall+0x88/0x1a0 [<ffff8000006aaac0>] kernel_init_freeable+0x148/0x1e8 [<ffff8000004f8ee4>] kernel_init+0x10/0xd4 Code: 8b000263 92628479 d1000720 eb01001f (f9400340) ---[ end trace 3bc230562e926fa4 ]--- Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b Signed-off-by:
-
Steve Capper authored
commit 3d08c629 upstream. Commit: b8865767 ARM: KVM: user_mem_abort: support stage 2 MMIO page mapping introduced some code in user_mem_abort that failed to compile if STRICT_MM_TYPECHECKS was enabled. This patch fixes up the failing comparison. Signed-off-by:
Steve Capper <steve.capper@linaro.org> Reviewed-by:
Kim Phillips <kim.phillips@linaro.org> Signed-off-by:
-
Christoffer Dall authored
commit c3058d5d upstream. When creating or moving a memslot, make sure the IPA space is within the addressable range of the guest. Otherwise, user space can create too large a memslot and KVM would try to access potentially unallocated page table entries when inserting entries in the Stage-2 page tables. Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Acked-by:
-
Ard Biesheuvel authored
commit 37b54408 upstream. Handle the potential NULL return value of find_vma_intersection() before dereferencing it. Acked-by:
-
Vladimir Murzin authored
commit 37a34ac1 upstream. On some platforms with no power management capabilities, the hotplug implementation is allowed to return from a smp_ops.cpu_die() call as a function return. Upon a CPU onlining event, the KVM CPU notifier tries to reinstall the hyp stub, which fails on platform where no reset took place following a hotplug event, with the message: CPU1: smp_ops.cpu_die() returned, trying to resuscitate CPU1: Booted secondary processor Kernel panic - not syncing: unexpected prefetch abort in Hyp mode at: 0x80409540 unexpected data abort in Hyp mode at: 0x80401fe8 unexpected HVC/SVC trap in Hyp mode at: 0x805c6170 since KVM code is trying to reinstall the stub on a system where it is already configured. To prevent this issue, this patch adds a check in the KVM hotplug notifier that detects if the HYP stub really needs re-installing when a CPU is onlined and skips the installation call if the stub is already in place, which means that the CPU has not been reset. Signed-off-by:
Vladimir Murzin <vladimir.murzin@arm.com> Acked-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by:
-
Joel Schopp authored
commit dbff124e upstream. The current aarch64 calculation for VTTBR_BADDR_MASK masks only 39 bits and not all the bits in the PA range. This is clearly a bug that manifests itself on systems that allocate memory in the higher address space range. [ Modified from Joel's original patch to be based on PHYS_MASK_SHIFT instead of a hard-coded value and to move the alignment check of the allocation to mmu.c. Also added a comment explaining why we hardcode the IPA range and changed the stage-2 pgd allocation to be based on the 40 bit IPA range instead of the maximum possible 48 bit PA range. - Christoffer ] Reviewed-by:
Joel Schopp <joel.schopp@amd.com> Signed-off-by:
-
