- 12 Nov, 2022 1 commit
-
-
Richard Acayan authored
The Qualcomm Snapdragon 670 has been out for a while. Add a device tree for it and the Google Pixel 3a as the first device. The Pixel 3a has the same bootloader issue as the Pixel 3 and will not work on Android 10 bootloaders or later until it gets fixed for the Pixel 3. SoC Initial Features: - power management - clocks - pinctrl - eMMC - USB 2.0 - GENI I2C - IOMMU - RPMh - interrupts Device-Specific Initial Features: - side buttons (keys) - regulators - touchscreen Signed-off-by:
Richard Acayan <mailingradian@gmail.com> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20221111001818.124901-5-mailingradian@gmail.com
-
- 11 Nov, 2022 4 commits
-
-
Sibi Sankar authored
The Google Herobrine WIFI SKU can save 256M by not having modem/mba/rmtfs memory regions defined. Add the dts fragment and mark all the board files appropriately. Reviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
Sibi Sankar <quic_sibis@quicinc.com> Signed-off-by:
-
Sibi Sankar authored
When the modem node was re-located to a separate LTE source file "sc7280-herobrine-lte-sku.dtsi", some of the previous LTE users weren't marked appropriately. Fix this by marking all Qualcomm reference devices as LTE. Suggested-by:
-
Luca Weiss authored
Fairphone 4 uses sdhc_2 for the SD card, configure the pins for it and enable it. The regulators which are exclusively used for SDHCI have their maximum voltage decreased to what downstream sets on the consumer side, like on many other platforms and allowed to set the load. Signed-off-by:
Luca Weiss <luca.weiss@fairphone.com> Reviewed-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by:
-
Krzysztof Kozlowski authored
spi-max-frequency is a property of SPI device, not the controller: qcom/sm8450-hdk.dtb: geniqup@8c0000: spi@880000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected Signed-off-by:Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
-
- 10 Nov, 2022 7 commits
-
-
Bjorn Andersson authored
Add gpio-keys for exposing the LID switch state. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by:
Johan Hovold <johan+linaro@kernel.org> Tested-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Tested-by:
Steev Klimaszewski <steev@kali.org> Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Remove redundant and undocumented property qcom,port-offset in soundwire controller nodes. This patch is required to avoid dtbs_check errors with qcom,soundwire.yaml Fixes: 12ef689f ("arm64: dts: qcom: sc7280: Add nodes for soundwire and va tx rx digital macro codecs") Signed-off-by:
Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> Co-developed-by:
Ratna Deepthi Kudaravalli <quic_rkudarav@quicinc.com> Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Remove redundant and undocumented property qcom,port-offset in soundwire controller nodes. This patch is required to avoid dtbs_check errors with qcom,soundwire.yaml Fixes: 24f52ef0 ("arm64: dts: qcom: sm8250: Add nodes for tx and rx macros with soundwire masters") Signed-off-by:
-
Srinivasa Rao Mandadapu authored
Update soundwire secondary nodes of WSA speaker to match with dt-bindings pattern properties regular expression. This modification is required to avoid dtbs-check errors occurred with qcom,soundwire.yaml. Signed-off-by:
-
Alex Elder authored
In "sc7280-idp.dts", the IPA node is modified after being defined. However that file includes "sc7280-idp.dtsi", which also modifies the IPA node (in the same way). This only needs to be done in "sc7280-idp.dtsi". Signed-off-by:
Alex Elder <elder@linaro.org> Reviewed-by:
-
Maulik Shah authored
Add power-domains property which allows apps_rsc device to attach to cluster power domain on sm8150, sm8250, sm8350 and sm8450. Signed-off-by:
Maulik Shah <quic_mkshah@quicinc.com> Reviewed-by:
Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8450 Signed-off-by:
-
- 08 Nov, 2022 28 commits
-
-
Dmitry Baryshkov authored
Change order of SMMU clocks to match the schema. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by:
-
Job Noorman authored
Add Himax hx83112b touchscreen to the FP3 DT. Signed-off-by:
Job Noorman <job@noorman.info> Reviewed-by:
-
Konrad Dybcio authored
Add support for Sony Xperia 10 IV, a.k.a PDX225. This device is a part of the SoMC SM6375 Murray platform and currently it is the only device based on that board, so no -common DTSI is created until (if?) other Murray devices appear. This commit brings support for: * USB (only USB2 for now) * Display via simplefb To create a working boot image, you need to run: cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/sm6375-sony-xperia-\ murray-pdx225.dtb > .Image.gz-dtb mkbootimg \ --kernel .Image.gz-dtb \ --ramdisk some_initrd.img \ --pagesize 4096 \ --base 0x0 \ --kernel_offset 0x8000 \ --ramdisk_offset 0x1000000 \ --tags_offset 0x100 \ --cmdline "SOME_CMDLINE" \ --dtb_offset 0x1f00000 \ --header_version 1 \ --os_version 12 \ --os_patch_level 2022-04 \ # or newer -o boot.img-sony-xperia-pdx225 Then, you need to flash it on the device and get rid of all the vendor_boot/dtbo mess: First, you need to get rid of vendor_boot. However, the bootloader is utterly retarded and it will not let you neither flash nor erase it. There are a couple ways to handle this: you can either dd /dev/zero to it from Android (if you have root) or a custom recovery or from fastbootd (fastboot/adb reboot fastboot). You will not be able to boot Android images on your phone unless you lock the bootloader (fastboot oem lock) and restore the factory image with Xperia Companion Windows-and-macOS-only software. The best way so far is probably to use the second (_b) slot and flash mainline there. This will however require you to flash some partitions manually, as they are not populated from factory: (boot_b, dtbo_b, vendor_boot_b, vbmeta_b, vbmeta_system_b) - these we don't really care about as we nuke/replace them (dsp_b, imagefv_b, modem_b, oem_b, rdimage_b) - these you NEED to populate to get a successful boot on slot B, otherwise you will have limited / no functionality. To switch slots, simply run: fastboot --set-active=a //or =b The rest assumes you are on slot A. // You have to either pull vbmeta{"","_system"} from // /dev/block/bootdevice/by-name/ or build one as a part of AOSP fastboot --disable-verity --disable-verification flash vbmeta_b vbmeta.img fastboot --disable-verity --disable-verification flash vbmeta_system_b \ vbmeta_system.img fastboot flash boot_b boot.img-sony-xperia-pdx225 fastboot reboot fastboot // entering fastbootd fastboot flash vendor_boot_b emptything.img fastboot flash dtbo_b emptything.img fastboot reboot bootloader // entering bootloader fastboot fastboot --set-active=b fastboot reboot // mainline time! Where emptything.img is a tiny file that consists of 2 bytes (all zeroes), doing a "fastboot erase" won't cut it, the bootloader will go crazy and things will fall apart when it tries to overlay random bytes from an empty partition onto a perfectly good appended DTB. From there on you can flash new mainline builds by simply flashing boot.img that you create after each kernel rebuild. Signed-off-by: -
Konrad Dybcio authored
Add an initial device tree for the SM6375 (SD695) SoC. Signed-off-by:
-
Konrad Dybcio authored
Add a compatible for Kryo 660 CPUs found in at least Qualcomm SM6375. Signed-off-by:
-
Stephen Boyd authored
Update the fingerprint node on Trogdor to match the fingerprint DT binding. This will allow us to drive the reset and boot gpios from the driver when it is re-attached after flashing. We'll also be able to boot the fingerprint processor if the BIOS isn't doing it for us. Cc: Douglas Anderson <dianders@chromium.org> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Alexandru M Stan <amstan@chromium.org> Signed-off-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
-
Stephen Boyd authored
Update the fingerprint node on Herobrine to match the fingerprint DT binding. This will allow us to drive the reset and boot gpios from the driver when it is re-attached after flashing. We'll also be able to boot the fingerprint processor if the BIOS isn't doing it for us. Cc: Douglas Anderson <dianders@chromium.org> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Alexandru M Stan <amstan@chromium.org> Signed-off-by:
-
Marijn Suijten authored
Downstream sources confirm sm6125 supports CQE, and after fixing the reg name for this range [1] this feature probes and enables correctly: [ 0.391950] sdhci_msm 4744000.mmc: mmc0: CQE init: success [1]: https://lore.kernel.org/all/20221026163646.37433-1-krzysztof.kozlowski@linaro.org/Signed-off-by:Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by:
-
Krzysztof Kozlowski authored
SM6125 comes with SDCC (SDHCI controller) v5, so the second range of registers is cqhci, not core. Fixes: cff4bbaf ("arm64: dts: qcom: Add support for SM6125") Signed-off-by:
-
Luca Weiss authored
The spmi-pmic bindings say that pm8941-coincell should be called 'charger'. Reviewed-by:
Luca Weiss <luca@z3ntu.xyz> Signed-off-by:
-
Konrad Dybcio authored
Make sure all multiline C-style commends begin with just '/*' with the comment text starting on a new line. Signed-off-by:
-
Konrad Dybcio authored
Switch '//' comments to C-style /* */. Signed-off-by:
-
Konrad Dybcio authored
Make sure all multiline C-style commends begin with just '/*' with the comment text starting on a new line. Signed-off-by:
-
Konrad Dybcio authored
Make sure all multiline C-style commends begin with just '/*' with the comment text starting on a new line. Also, trim off downstream regulator properties from comments to prevent them from accidentally landing into mainline one day.. Signed-off-by:
-
Konrad Dybcio authored
Make sure all multiline C-style commends begin with just '/*' with the comment text starting on a new line. Also, fix up some whitespace within comments. Signed-off-by:
-
Konrad Dybcio authored
Switch '//' comments to C-style /* */. Make sure all multiline C-style commends begin with just '/*' with the comment text starting on a new line. Signed-off-by:
-
Konrad Dybcio authored
Switch '//' comments to C-style /* */. Signed-off-by:
-
Konrad Dybcio authored
Switch '//' comments to C-style /* */ and fix up the contents of some. Signed-off-by:
-
Konrad Dybcio authored
Switch '//' comments to C-style /* */ and fix up the contents of some. Signed-off-by:
-
Konrad Dybcio authored
Switch '//' comments to C-style /* */ and fix up the contents of some. Make sure all multiline C-style commends begin with just '/*' with the comment text starting on a new line. Also, fix up a single raw '2' to PM8994_GPIO_S4 while at it. Signed-off-by:
-
Konrad Dybcio authored
Switch '//' comments to C-style /* */ and fix up the contents of some. Make sure all multiline C-style commends begin with just '/*' with the comment text starting on a new line. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Robert Marko authored
Use respective GPIO_ACTIVE_LOW/HIGH flags for tlmm GPIOs instead of harcoding the cell value. Signed-off-by:
Robert Marko <robimarko@gmail.com> Reviewed-by:
-
Robert Marko authored
Use respective GPIO_ACTIVE_LOW/HIGH flags for tlmm GPIOs instead of harcoding the cell value. Signed-off-by:
-
Robert Marko authored
Use "okay" instead of "ok" in USB nodes as "ok" is deprecated. Signed-off-by:
-
Konrad Dybcio authored
Use my new Linaro address in place of my SoMainline one. Signed-off-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
-
Johan Hovold authored
Update the USB MP QMP PHY nodes to match the new binding which specifically includes the missing register regions (e.g. PCS_USB). Signed-off-by:
Andrew Halaney <ahalaney@redhat.com> Signed-off-by:
-
Sheng-Liang Pan authored
arm64: dts: qcom: sc7280: sort out the "Status" to last property with sc7280-herobrine-audio-rt5682.dtsi To keep diffs clean, sort out "Status" to last property. Signed-off-by:
Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com> Reviewed-by:
-
