From Jason Cooper:
 - add the Openblocks A7 board
 - add Netgear ReadyNAS 104 board

* tag 'dt-3.13-5' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: Add Netgear ReadyNAS 104 board
  ARM: kirkwood: add support for OpenBlocks A7 platform
Signed-off-by: Olof Johansson <olof@lixom.net>

A handful of DT updates from Christian Daudt for the broadcom mobile
platforms, including their rename of the platform to BCM_MOBILE to keep
BCM for the vendor-level options.

* bcm/dt:
  ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
  ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
  ARM: dts: bcm281xx: Add card detect GPIO
  ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
  ARM: bcm281xx: Add device node for the GPIO controller
Signed-off-by: Olof Johansson <olof@lixom.net>

Trivial patch to make use of GIC/IRQ defines on the bcm11351 sdio
interrupt properties.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This adds in three more UARTs that were not declared earlier.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Register GPIO 14 as card detect interrupt for the SD card slot.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Currently ARCH_BCM has been used for Broadcom
Mobile V7 based SoCs. In order to allow other Broadcom
SoCs to also use mach-bcm directory and files, this patch
renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing
in mach-bcm directory.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the GPIO controller device node for the Broadcom bcm281xx family of
mobile SoCs.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Main hardware parts of the (Armada 370 based) NETGEAR ReadyNAS 104 are
supported by mainline kernel (USB 3.0 rear ports, USB 2.0 front port,
Gigabit controller and PHYs, serial port, LEDs, buttons, SATA ports,
G762 fan controller) and referenced in provided .dts file. Some additonal
work remains for:

 - Intersil ISL12057 I2C RTC and Alarm chip: working driver but needs
   to be splitted for submission of RTC part first;
 - Front LCD (Winstar 1602G): driver needs to be written
 - Armada NAND controller (to access onboard 128MB of NAND): support
   being pushed by @free-electrons people
 - 4 front SATA LEDs controlled via GPIO brought by NXP PCA9554:
   driver is available upstream. Not referenced/tested yet.

but the device is usable w/o those.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The IOMMU node's reg property contains completely bogus values! Somehow,
this had no practical effect, despite the fact the IOMMU driver appears
to be writing to those registers. I suppose that since no HW modules is
actually at that address, the writes simply had no effect.

Note that I'm not CCing stable here, even though the problem exists as
far back as v3.9, simply because this patch doesn't fix any observed
issue, and I don't want to run the risk of suddenly writing to some
registers and causing a regression.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, wrote commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The OpenBlocks A7 board is designed and sold by PlatHome, and based on
a Kirkwood 6283 Marvell SoC. It is quite similar to the OpenBlocks A6
already supported in the kernel, with the following main differences:

 - The A6 uses a RTC on I2C, while the A7 uses the internal SoC RTC.

 - The A6 has one Ethernet port, while the A7 has two Ethernet ports

 - The A6 has only one USB port, while the A7 integrates a USB hub,
   which provides two front-side USB port, and an internal USB port as
   well.

 - The A6 has 512 MB of RAM, while the A7 has 1 GB of RAM.

 - Slightly different GPIOs for some functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Merge tag 'omap-for-v3.13/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

From Tony Lindgren:
Few device tree changes that fix boot time warnings and
make panda display work with recent u-boot.

* tag 'omap-for-v3.13/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap4-panda: add DPI pinmuxing
  ARM: dts: AM33xx: Add RNG node
  ARM: dts: AM33XX: Add hwspinlock node
  ARM: dts: OMAP5: Add hwspinlock node
  ARM: dts: OMAP4: Add hwspinlock node
Signed-off-by: Olof Johansson <olof@lixom.net>

New u-boot versions no longer set the pinmuxing for Panda's DPI output,
and the muxing has to be done in the .dts file.

Add pinmuxing for DPI and TFP410. Without these, the DVI output on Panda
does not work with recent u-boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the AM33xx RNG module's device tree data.
Also add Documentation file describing the data
for the RNG module.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for AM33xx family
of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for OMAP5 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the hwspinlock device tree node for OMAP4 family
of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Set the default status for PCIe to disabled in the exynos5440.dtsi
file and let the board dts files such as exynos5440-ssdk5440.dts
enable the PCIe. However, keep the PCIe for SD5v1 board disabled,
because there is no PCIe slot on SD5v1 board.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

From Barry Song:
Some missed dt nodes for sirf dts for 3.13. Among them:
 - add missed chhifbg node in prima2 and atlas6 dts
 - add missed cell, cs and dma channel for SPI nodes
 - add missed graphics2d iobg in atlas6 dts
 - add missed address-cells and size-cells for prima2 I2C
 - add missed memcontrol-monitor node in prima2 and atlas6 dts

* sirf/dt:
  ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
  ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
  ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
  ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
  ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
Signed-off-by: Olof Johansson <olof@lixom.net>

here prima2 i2c node is lacking of address-cells and size-cells.
Signed-off-by: Renwei Wu <Renwei.Wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

here we need to add missed cell, cs and dma channels prop in SPI nodes
to match with drivers.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

there is a bus bridge for graphics 2D module lost in current dts, this patch takes it
back.
Signed-off-by: Jiansong Chen <jiansong.chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

CPHIF(Cell phone interface) is behind sys bridge, this patch adds the
missed node.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

memcontrol-monitor provides the ability of monitoring the memory bandwidth.
Signed-off-by: Ye He <ye.he@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:

- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272

* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
  ARM: dts: omap5-uevm: Remove pinmux for dmic pins
  ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
  ARM: dts: TWL4030: Add power button support
  ARM: dts: omap3-n900: Add LP5523 support
  ARM: dts: omap3-n900: Add TLV320AIC3X support
  ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
  ARM: dts: omap3-n900: Add NAND support
  ARM: dts: omap3-n900: Specify regulator info
  ARM: dts: TWL4030: Add missing regulators
  ARM: dts: omap3-n900: Add LP5523 support
  ARM: dts: omap3-n900: Add vibrator device
  ARM: dts: omap3-n900: GPIO key definitions
  ARM: dts: omap3-n900: Add support for SD cards
  ARM: dts: omap3-n900: Add UART support
  ARM: dts: omap3-n900: Fix i2c bus speed
  ARM: dts: omap3-n900: Add pinctrl for i2c devices
  ARM: dts: DRA7: Add CPU OPP table
  ARM: dts: OMAP5: Add CPU OPP table
  ARM: dts: dra7-evm: add smps123 supply for CPU
  ARM: dts: omap5-uevm: add smps123 supply for CPU
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.13/cpufreq-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

From Tony Lindgren:
Few patches to make cpufreq work for omap3 with device tree.

Note that this branch has a dependency to the patches merged
with omap-for-v3.13/board-removal-signed-take2.

* tag 'omap-for-v3.13/cpufreq-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP3+: use cpu0-cpufreq driver in device tree supported boot
  ARM: OMAP2+: add missing lateinit hook for calling pm late init
  ARM: OMAP3+: do not register non-dt OPP tables for device tree boot
Signed-off-by: Olof Johansson <olof@lixom.net>

From Jason Cooper, mvebu dt changes for v3.13 (round 4):

 - mvebu
    - core divider clock driver dt binding and nodes

* tag 'dt-3.13-4' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: Add the core-divider clock to Armada 370/XP
  ARM: mvebu: Add a 2 GHz fixed-clock Armada 370/XP
  ARM: mvebu: Add Core Divider clock device-tree binding

From Shawn Guo:
The imx/mxs device tree changes for 3.13:

- Use macros for mxs pinctrl settings
- New board support: VF610 Cosmic/Cosmic+, imx6q-udoo, MSR M28CU3
- Support DSPI device for vf610
- Add PCIe device for imx6qdl
- Add UHS pinctrl states for imx6sl and imx6qdl
- Display support for APF and imx51-babbage boards
- Enable SPI NOR and USB for imx6sl-evk board
- Enable LVDS for imx6q-sabrelite and SPDIF for imx6qdl-wandboard
- Misc updates on boards: TX28, imx6qdl-wandboard, imx53-qsb etc.
- Some random updates on imx51 device tree

* tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (44 commits)
  ARM: imx: imx6sl iomuxc syscon is compatible to imx6q
  ARM: dts: imx6sl-evk: enable the SPI NOR
  ARM: dts: imx6sl: add a pinctrl for ECSPI1
  ARM: imx27: add missing #pwm-cells property
  ARM: dts: imx6sl: add pinctrl uhs states for usdhc
  ARM: dts: imx6qdl-sabresd: Add backlight support for lvds
  ARM: dts: imx51-babbage: Make DVI and WVGA panel functional
  ARM: imx27-apf27dev: Add framebuffer support
  ARM: imx51-apf51dev: Add parallel display support
  ARM: dts: imx53-qsb: Do not use GPIO1_8 as wakeup source
  ARM: dts: imx53-qsb: SDHC1 does not have cd-gpios
  ARM: dts: imx53-qsb: SDHC3 is connected in 8-bit mode
  ARM: dts: mxs: Add MSR M28CU3 board
  ARM: dts: imx6qdl-wandboard: Provide phy-reset-gpios
  ARM: dts: imx6qdl-sabresd: Provide phy-reset-gpios
  ARM: dts: imx6q-sabrelite: Add ethernet phy reset pin into hog
  ARM: dts: imx6qdl: add pcie device node
  ARM: dts: imx6q-udoo: Add initial board support
  ARM: dts: mxs: Add muxing options for the SSP2 MMC
  ARM: dts: add initial VF610 Cosmic/Cosmic+ board support
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge most of tag 'tags/exynos-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git into next/dt

From Kukjin Kim, these are device-tree updates for Exynos. Among the changes:
- add MIPI PHY node for exynos4
- update regulator for origen and exynos5250-arndale
- add support HDMI for exynos5250, exynos5420

* commit '93457b9c':
  ARM: dts: Add HDMI related I2C nodes for Arndale board
  ARM: dts: enable hdmi subsystem for exynos5420 smdk board
  ARM: dts: add dt nodes for hdmi subsystem for exynos5420
  ARM: dts: add i2c device nodes for Exynos5420
  ARM: dts: add clocks to hdmi dt node for exynos5250
  ARM: dts: add mixer clocks to mixer node for Exynos5250
  of/documentation: update with clock information for exynos hdmi subsystem
  ARM: dts: Disable Exynos5250 I2S controllers by default
  ARM: dts: Add reg property to regulator nodes in exynos5250-arndale
  ARM: dts: Add fixed voltage regulator to simple bus for origen
  ARM: dts: Add MIPI PHY node to exynos4.dtsi

Merge tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt

From Linus Walleij:
Five incremental device tree patches around the clock handling,
and adding SSP/SPI devices to the device tree.

* tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: register all SSP and SPI blocks
  ARM: ux500: fix I2C4 clock bit
  ARM: ux500: fix clock for GPIO blocks 6 and 7
  clk: ux500: fix erroneous bit assignment
  ARM: ux500: fix clock for GPIO block 8
Signed-off-by: Olof Johansson <olof@lixom.net>

From Maxime Ripard:
Allwinner sunXi SoCs minor fixes for 3.13

* tag 'sunxi-fixes-for-3.13' of https://github.com/mripard/linux:
  ARM: sun6i: Fix the APB2 clock gates register size
Signed-off-by: Olof Johansson <olof@lixom.net>

From Maxime Ripard:
Allwinner sunXi SoCs device tree changes for 3.13

This DT series sees the introduction of the cubietruck DT, plus the addition of
the i2c controller for the A20 based boards, and of the Security ID found in
all the Allwinner SoCs but the A31.

* tag 'sunxi-dt-for-3.13' of https://github.com/mripard/linux:
  ARM: sunxi: dts: Add support for the cubieboard3, the CubieTruck
  ARM: sun7i: olinuxino-micro: Enable the I2C controllers
  ARM: sun7i: cubieboard2: Enable the I2C controllers
  ARM: sun7i: Add the pin muxing options for the I2C controllers
  ARM: sun7i: Enable the I2C controllers
  ARM: sunxi: dt: Add sunxi-sid to dts for sun4i, sun5i and sun7i
Signed-off-by: Olof Johansson <olof@lixom.net>

The Armada 370/XP SoC has a clock provider called "Core Divider",
that is derived from a fixed 2 GHz PLL clock.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Armada 370/XP SoCs have a 2 GHz fixed PLL that is used to feed
other clocks. This commit adds a DT representation of this clock
through a fixed-clock compatible node.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 370/XP SoCs have a Core Divider clock providing
several clocks. For now, only the NAND clock is supported.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Merge tag 'for_3.13_super_late/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.13/dt

Add a lot of N900 nodes
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board

When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
Panda5 does not have support for digital microphones so remove the pinmux
section for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
On uEVM the twl6040 reset GPIO is from gpio5_141 and not via gpio5_145, which
was the case in sEVM.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Enable support for the power button.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add support for LP5523 device.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This patch adds support for Nokia N900 TLV320AIC3X chips.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>