- 21 Jun, 2023 39 commits
-
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks vetoing of a different aspect of the configuration and the bridge does not need to participate in routing traffic. The IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
Danielle Ratson <danieller@nvidia.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge (this holds for both bridges used here), the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks traffic prioritization and scheduling, and the bridges serve for their L2 forwarding capabilities, and do not need to participate in routing traffic. The IP addresses or the RIFs are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in this selftest, thus exempting them from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge (this holds for both bridges used here), the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks traffic prioritization and scheduling, and the bridges serve for their L2 forwarding capabilities, and do not need to participate in routing traffic. The IP addresses or the RIFs are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in this selftest, thus exempting them from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks DCB DSCP-based prioritization, and the bridge serves for its L2 forwarding capabilities, and does not need to participate in routing traffic. The IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks how many mirroring sessions a machine is capable of offloading. The IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge (this holds for all bridges used here), the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks whether a different vetoed aspect of the configuration provides an extack. The IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in this selftest, thus exempting them from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are not allowed to be created for 802.1ad bridges, but the address indicates one needs to be created. Thus the veto selftests fail already during the port enslavement. Then the attempt to create a VLAN on top of the same bridge is not vetoed, because the bridge is not related to mlxsw, and the selftest fails. Fix by disabling automatic IPv6 address generation for the bridges in this selftest, thus exempting them from the mlxsw router attention. Signed-off-by:
Amit Cohen <amcohen@nvidia.com> Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The bridge eventually inherits MAC address from its first member, after the enslavement is acked. A number of (mainly VXLAN) selftests already work around the problem by setting the MAC address to whatever it will eventually be anyway. Do the same here. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The bridge eventually inherits MAC address from its first member, after the enslavement is acked. A number of (mainly VXLAN) selftests already work around the problem by setting the MAC address to whatever it will eventually be anyway. Do the same for several mirror_gre selftests. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. These two selftests however check mirroring traffic to a gretap netdevice. The bridge here does not participate in routing traffic and the IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridges in these selftests, thus exempting them from mlxsw router attention. Since the bridges are only used for L2 forwarding, this change should not hinder usefulness of this selftest for testing SW datapath or HW datapaths in other devices. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks whether skbedit changes packet priority as appropriate. The bridge thus does not need to participate in routing traffic and the IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Since the bridge is only used for L2 forwarding, this change should not hinder usefulness of this selftest for testing SW datapath or HW datapaths in other devices. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. At the time that the front panel port is enslaved to the bridge, the bridge MAC address does not have the same prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all the RIFs have to have the same 38-bit MAC address prefix. Since the bridge does not obey this limitation, the RIF cannot be created, and the enslavement attempt is vetoed on the grounds of the configuration not being offloadable. The selftest itself however checks operation of pedit on IPv4 and IPv6 dsfield and its parts. The bridge thus does not need to participate in routing traffic and the IP address or the RIF are irrelevant. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Since the bridge is only used for L2 forwarding, this change should not hinder usefulness of this selftest for testing SW datapath or HW datapaths in other devices. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. This will cause this selftest to fail spuriously. The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are not allowed to be created for 802.1ad bridges, but the address indicates one needs to be created. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Petr Machata authored
In a future patch, mlxsw will start adding RIFs to uppers of front panel port netdevices, if they have an IP address. This will cause this selftest to fail spuriously. The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are not allowed to be created for 802.1ad bridges, but the address indicates one needs to be created. Fix by disabling automatic IPv6 address generation for the HW-offloaded bridge in this selftest, thus exempting it from mlxsw router attention. Signed-off-by:
-
Horatiu Vultur authored
Currently for each timestamp frame, the SW needs to go and read the received timestamp over the MDIO bus. But the HW has the capability to store the received nanoseconds part and the least significant two bits of the seconds in the reserved field of the PTP header. In this way we could save few MDIO transactions (actually a little more transactions because the access to the PTP registers are indirect) for each received frame. Instead of reading the rest of seconds part of the timestamp of the frame using MDIO transactions schedule PTP worker thread to read the seconds part every 500ms and then for each of the received frames use this information. Because if for example running with 512 frames per second, there is no point to read 512 times the second part. Doing all these changes will give a great CPU usage performance. Running ptp4l with logSyncInterval of -9 will give a ~60% CPU improvement. Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Bartosz Golaszewski says: ==================== net: stmmac: dwmac-qcom-ethqos: add support for EMAC4 Extend the dwmac-qcom-ethqos driver to support EMAC4. While at it: rework the code somewhat. The bindings have been reviewed by DT maintainers. This is a sub-series of [1] with only the patches targetting the net subsystem as they can go in independently. [1] https://lore.kernel.org/lkml/20230617001644.4e093326@kernel.org/T/ ==================== Link: https://lore.kernel.org/r/20230619092402.195578-1-brgl@bgdev.plSigned-off-by:
-
Bartosz Golaszewski authored
sa8775p uses EMAC version 4, add the relevant defines, rename the has_emac3 switch to has_emac_ge_3 (has emac greater-or-equal than 3) and add the new compatible. Signed-off-by:
Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by:
-
Bartosz Golaszewski authored
Add the compatible for the MAC controller on sa8775p platforms. This MAC works with a single interrupt so add minItems to the interrupts property. The fourth clock's name is different here so change it. Enable relevant PHY properties. Add the relevant compatibles to the binding document for snps,dwmac as well. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Bartosz Golaszewski authored
On some platforms, the PCS can be integrated in the MAC so the driver will not see any PCS link activity. Add a switch that allows the platform drivers to let the core code know. Signed-off-by:
Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by:
-
Bartosz Golaszewski authored
On sa8775p the MAC is connected to the external PHY over SGMII so add support for it to the driver. Signed-off-by:
-
Bartosz Golaszewski authored
In preparation for supporting SGMII, let's make the code a bit more generic. Add a new callback for MAC configuration so that we can assign a different variant of it in the future. Signed-off-by:
Andrew Halaney <ahalaney@redhat.com> Signed-off-by:
-
Bartosz Golaszewski authored
On sa8775p, the EMAC revision is 4 and we use SGMII instead of RGMII. There's no "rgmii" clock but there's a fourth clock under a different name: "phyaux". Add a new field to the chip data struct that specifies the link clock name. Default to "rgmii" for backward compatibility. Signed-off-by:
-
Bartosz Golaszewski authored
On sa8775p platforms, there's a SGMII SerDes PHY between the MAC and external PHY that we need to enable and configure. Signed-off-by:
-
Bartosz Golaszewski authored
There's an unnecessary space in the rgmii_updatel() function, remove it. Signed-off-by:
-
Bartosz Golaszewski authored
Typically we use a newline between global and local headers so add it here as well. Signed-off-by:
-
Bartosz Golaszewski authored
device_get_phy_mode() is declared in linux/property.h but this header is not included. Signed-off-by:
-
Bartosz Golaszewski authored
Shrink code and avoid line breaks by using a helper variable for &pdev->dev. Signed-off-by:
-
Bartosz Golaszewski authored
Make sure we follow the reverse-xmas tree convention. Signed-off-by:
-
Bartosz Golaszewski authored
The err_mem label's name is unclear. It actually should be reached on any error after stmmac_probe_config_dt() succeeds. Name it after the cleanup action that needs to be called before exiting. Signed-off-by:
-
Bartosz Golaszewski authored
We can use a devm action to completely drop the remove callback and use stmmac_pltfr_remove() directly for remove. We can also drop one of the goto labels. Signed-off-by:
-
Arnd Bergmann authored
The new efx_bind_neigh() function contains a broken code path when IPV6 is disabled: drivers/net/ethernet/sfc/tc_encap_actions.c:144:7: error: variable 'n' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized] if (encap->type & EFX_ENCAP_FLAG_IPV6) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/sfc/tc_encap_actions.c:184:8: note: uninitialized use occurs here if (!n) { ^ drivers/net/ethernet/sfc/tc_encap_actions.c:144:3: note: remove the 'if' if its condition is always false if (encap->type & EFX_ENCAP_FLAG_IPV6) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/sfc/tc_encap_actions.c:141:22: note: initialize the variable 'n' to silence this warning struct neighbour *n; ^ = NULL Change it to use the existing error handling path here. Fixes: 7e5e7d80 ("sfc: neighbour lookup for TC encap action offload") Suggested-by:Edward Cree <ecree.xilinx@gmail.com> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
-
Arnd Bergmann authored
The driver now fails to link when CONFIG_INET is disabled, so add an explicit Kconfig dependency: ld.lld: error: undefined symbol: ip_route_output_flow >>> referenced by tc_encap_actions.c >>> drivers/net/ethernet/sfc/tc_encap_actions.o:(efx_tc_flower_create_encap_md) in archive vmlinux.a ld.lld: error: undefined symbol: ip_send_check >>> referenced by tc_encap_actions.c >>> drivers/net/ethernet/sfc/tc_encap_actions.o:(efx_gen_encap_header) in archive vmlinux.a >>> referenced by tc_encap_actions.c >>> drivers/net/ethernet/sfc/tc_encap_actions.o:(efx_gen_encap_header) in archive vmlinux.a ld.lld: error: undefined symbol: arp_tbl >>> referenced by tc_encap_actions.c >>> drivers/net/ethernet/sfc/tc_encap_actions.o:(efx_tc_netevent_event) in archive vmlinux.a >>> referenced by tc_encap_actions.c >>> drivers/net/ethernet/sfc/tc_encap_actions.o:(efx_tc_netevent_event) in archive vmlinux.a Fixes: a1e82162 ("sfc: generate encap headers for TC offload") Reviewed-by:
Simon Horman <simon.horman@corigine.com> Closes: https://lore.kernel.org/oe-kbuild-all/202306151656.yttECVTP-lkp@intel.com/Signed-off-by:
-
Andrew Lunn authored
The text has been cut/paste from genphy_c45_ethtool_get_eee but not changed to reflect it performs set. Additionally, extend the comment. This function implements the logic that eee_enabled has global control over EEE. When eee_enabled is false, no link modes will be advertised, and as a result, the MAC should not transmit LPI. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230619220332.4038924-1-andrew@lunn.chSigned-off-by:
-
Eric Dumazet authored
Blamed commit added these helpers for sake of detecting RAW sockets specific ioctl. syzbot complained about it [1]. Issue here is that RAW sockets could pretend there was no need to call ipmr_sk_ioctl() Regardless of inet_sk(sk)->inet_num, we must be prepared for ipmr_ioctl() being called later. This must happen from ipmr_sk_ioctl() context only. We could add a safety check in ipmr_ioctl() at the risk of breaking applications. Instead, remove sk_is_ipmr() and sk_is_icmpv6() because their name would be misleading, once we change their implementation. [1] BUG: KASAN: stack-out-of-bounds in ipmr_ioctl+0xb12/0xbd0 net/ipv4/ipmr.c:1654 Read of size 4 at addr ffffc90003aefae4 by task syz-executor105/5004 CPU: 0 PID: 5004 Comm: syz-executor105 Not tainted 6.4.0-rc6-syzkaller-01304-gc08afcdc #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106 print_address_description.constprop.0+0x2c/0x3c0 mm/kasan/report.c:351 print_report mm/kasan/report.c:462 [inline] kasan_report+0x11c/0x130 mm/kasan/report.c:572 ipmr_ioctl+0xb12/0xbd0 net/ipv4/ipmr.c:1654 raw_ioctl+0x4e/0x1e0 net/ipv4/raw.c:881 sock_ioctl_out net/core/sock.c:4186 [inline] sk_ioctl+0x151/0x440 net/core/sock.c:4214 inet_ioctl+0x18c/0x380 net/ipv4/af_inet.c:1001 sock_do_ioctl+0xcc/0x230 net/socket.c:1189 sock_ioctl+0x1f8/0x680 net/socket.c:1306 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x197/0x210 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f2944bf6ad9 Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd8897a028 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f2944bf6ad9 RDX: 0000000000000000 RSI: 00000000000089e1 RDI: 0000000000000003 RBP: 00007f2944bbac80 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f2944bbad10 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> The buggy address belongs to stack of task syz-executor105/5004 and is located at offset 36 in frame: sk_ioctl+0x0/0x440 net/core/sock.c:4172 This frame has 2 objects: [32, 36) 'karg' [48, 88) 'buffer' Fixes: e1d001fa ("net: ioctl: Use kernel memory on protocol ioctl callbacks") Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Breno Leitao <leitao@debian.org> Cc: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Reviewed-by:
Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230619124336.651528-1-edumazet@google.comSigned-off-by:
-
Eric Dumazet authored
SIOCGETSGCNT_IN6 uses a "struct sioc_sg_req6 buffer". Unfortunately the blamed commit made hard to ensure type safety. syzbot reported: BUG: KASAN: stack-out-of-bounds in ip6mr_ioctl+0xba3/0xcb0 net/ipv6/ip6mr.c:1917 Read of size 16 at addr ffffc900039afb68 by task syz-executor937/5008 CPU: 1 PID: 5008 Comm: syz-executor937 Not tainted 6.4.0-rc6-syzkaller-01304-gc08afcdc #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106 print_address_description.constprop.0+0x2c/0x3c0 mm/kasan/report.c:351 print_report mm/kasan/report.c:462 [inline] kasan_report+0x11c/0x130 mm/kasan/report.c:572 ip6mr_ioctl+0xba3/0xcb0 net/ipv6/ip6mr.c:1917 rawv6_ioctl+0x4e/0x1e0 net/ipv6/raw.c:1143 sock_ioctl_out net/core/sock.c:4186 [inline] sk_ioctl+0x151/0x440 net/core/sock.c:4214 inet6_ioctl+0x1b8/0x290 net/ipv6/af_inet6.c:582 sock_do_ioctl+0xcc/0x230 net/socket.c:1189 sock_ioctl+0x1f8/0x680 net/socket.c:1306 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x197/0x210 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f255849bad9 Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd06792778 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f255849bad9 RDX: 0000000000000000 RSI: 00000000000089e1 RDI: 0000000000000003 RBP: 00007f255845fc80 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f255845fd10 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> The buggy address belongs to stack of task syz-executor937/5008 and is located at offset 40 in frame: sk_ioctl+0x0/0x440 net/core/sock.c:4172 This frame has 2 objects: [32, 36) 'karg' [48, 88) 'buffer' Fixes: e1d001fa ("net: ioctl: Use kernel memory on protocol ioctl callbacks") Reported-by:
Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20230619072740.464528-1-edumazet@google.comSigned-off-by:
-
Ratheesh Kannoth authored
TC rule support to offload rx queue mapping rules. Eg: tc filter add dev eth2 ingress protocol ip flower \ dst_ip 192.168.8.100 \ action skbedit queue_mapping 4 skip_sw action mirred ingress redirect dev eth5 Packets destined to 192.168.8.100 will be forwarded to rx queue 4 of eth5 interface. tc filter add dev eth2 ingress protocol ip flower \ dst_ip 192.168.8.100 \ action skbedit queue_mapping 9 skip_sw Packets destined to 192.168.8.100 will be forwarded to rx queue 4 of eth2 interface. Signed-off-by:Ratheesh Kannoth <rkannoth@marvell.com> Link: https://lore.kernel.org/r/20230619060638.1032304-1-rkannoth@marvell.comSigned-off-by:
-
Christophe JAILLET authored
Group some variables based on their sizes to reduce hole and avoid padding. On x86_64, this shrinks the size of 'struct netlbl_domaddr6_map' from 72 to 64 bytes. It saves a few bytes of memory and is more cache-line friendly. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Paul Moore <paul@paul-moore.com> Link: https://lore.kernel.org/r/aa109847260e51e174c823b6d1441f75be370f01.1687083361.git.christophe.jaillet@wanadoo.frSigned-off-by:
-
Christophe JAILLET authored
Group some variables based on their sizes to reduce hole and avoid padding. On x86_64, this shrinks the size of 'struct mptcp_pm_add_entry' from 136 to 128 bytes. It saves a few bytes of memory and is more cache-line friendly. Signed-off-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Reviewed-by:
-
Christophe JAILLET authored
Group some variables based on their sizes to reduce hole and avoid padding. On x86_64, this shrinks the size of 'struct mctp_route' from 72 to 64 bytes. It saves a few bytes of memory and is more cache-line friendly. Signed-off-by:
Jeremy Kerr <jk@codeconstruct.com.au> Reviewed-by:
-
- 20 Jun, 2023 1 commit
-
-
Lucas Stach authored
Commit 6970ef27 ("net: fec: add xdp and page pool statistics") selected CONFIG_PAGE_POOL_STATS from the FEC driver symbol, making it impossible to build without the page pool statistics when this driver is enabled. The help text of those statistics mentions increased overhead. Allow the user to choose between usefulness of the statistics and the added overhead. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Reviewed-by:
-
