This driver uses a set of local macros to manipulate the TX and RX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

A number of variables are initialized when declared that set later in the
routine, thus the initialization can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.

The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.

Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If the call to hw_init() fails for any of the drivers, the driver will
leak memory that was allocated in BT coexistence setup. Technically, each
of the drivers should have done this free; however placing it in rtl_pci
fixes all the drivers with only a single patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless/realtek/rtlwifi/efuse.c:16:31:
 warning: RTL8712_SDIO_EFUSE_TABLE defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/efuse.c:9:17:
 warning: MAX_PGPKT_SIZE defined but not used [-Wunused-const-variable=]

They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the process of converting the bit manipulation macros were converted
to use GENMASK(), the compiler reported a value too big for the field.
The offending statement was trying to write 0x100 into a 5-bit field.
An accompaning comment says to set bit 3, thus the code is changed
appropriately.

This error has been in the driver since its initial submission.

Fixes: 29d00a3e ("rtlwifi: rtl8192cu: Add routine trx")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fix spurious warning message when building with W=1:

  CC [M]  drivers/net/wireless/realtek/rtlwifi/usb.o
drivers/net/wireless/realtek/rtlwifi/usb.c:243: warning: Cannot understand  * on line 243 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:760: warning: Cannot understand  * on line 760 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:790: warning: Cannot understand  * on line 790 - I thought it was a doc line

Clean up the comment format.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Matteo Croce says:

====================
mvpp2: per-cpu buffers

This patchset workarounds an PP2 HW limitation which prevents to use
per-cpu rx buffers.
The first patch is just a refactor to prepare for the second one.
The second one allocates percpu buffers if the following conditions are met:
- CPU number is less or equal 4
- no port is using jumbo frames

If the following conditions are not met at load time, of jumbo frame is enabled
later on, the shared allocation is reverted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Every mvpp2 unit can use up to 8 buffers mapped by the BM (the HW buffer
manager). The HW will place the frames in the buffer pool depending on the
frame size: short (< 128 bytes), long (< 1664) or jumbo (up to 9856).

As any unit can have up to 4 ports, the driver allocates only 2 pools,
one for small and one long frames, and share them between ports.
When the first port MTU is set higher than 1664 bytes, a third pool is
allocated for jumbo frames.

This shared allocation makes impossible to use percpu allocators,
and creates contention between HW queues.

If possible, i.e. if the number of possible CPU are less than 8 and jumbo
frames are not used, switch to a new scheme: allocate 8 per-cpu pools for
short and long frames and bind every pool to an RXQ.

When the first port MTU is set higher than 1664 bytes, the allocation
scheme is reverted to the old behaviour (3 shared pools), and when all
ports MTU are lowered, the per-cpu buffers are allocated again.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor mvpp2_bm_pool_create(), mvpp2_bm_pool_destroy() and
mvpp2_bm_pools_init() so that they accept a struct device instead
of a struct platform_device, as they just need platform_device->dev.

Removing such dependency makes the BM code more reusable in context
where we don't have a pointer to the platform_device.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a function such as dsa_slave_create fails, currently the following
stack trace can be seen:

[    2.038342] sja1105 spi0.1: Probed switch chip: SJA1105T
[    2.054556] sja1105 spi0.1: Reset switch and programmed static config
[    2.063837] sja1105 spi0.1: Enabled switch tagging
[    2.068706] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[    2.076371] ------------[ cut here ]------------
[    2.080973] WARNING: CPU: 1 PID: 21 at net/core/devlink.c:6184 devlink_free+0x1b4/0x1c0
[    2.088954] Modules linked in:
[    2.092005] CPU: 1 PID: 21 Comm: kworker/1:1 Not tainted 5.3.0-rc6-01360-g41b52e38d2b6-dirty #1746
[    2.100912] Hardware name: Freescale LS1021A
[    2.105162] Workqueue: events deferred_probe_work_func
[    2.110287] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[    2.117992] [<c030d8cc>] (show_stack) from [<c10b08d8>] (dump_stack+0xb4/0xc8)
[    2.125180] [<c10b08d8>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[    2.132018] [<c0349d04>] (__warn) from [<c0349e34>] (warn_slowpath_null+0x40/0x48)
[    2.139549] [<c0349e34>] (warn_slowpath_null) from [<c0f19d74>] (devlink_free+0x1b4/0x1c0)
[    2.147772] [<c0f19d74>] (devlink_free) from [<c1064fc0>] (dsa_switch_teardown+0x60/0x6c)
[    2.155907] [<c1064fc0>] (dsa_switch_teardown) from [<c1065950>] (dsa_register_switch+0x8e4/0xaa8)
[    2.164821] [<c1065950>] (dsa_register_switch) from [<c0ba7fe4>] (sja1105_probe+0x21c/0x2ec)
[    2.173216] [<c0ba7fe4>] (sja1105_probe) from [<c0b35948>] (spi_drv_probe+0x80/0xa4)
[    2.180920] [<c0b35948>] (spi_drv_probe) from [<c0a4c1cc>] (really_probe+0x108/0x400)
[    2.188711] [<c0a4c1cc>] (really_probe) from [<c0a4c694>] (driver_probe_device+0x78/0x1bc)
[    2.196933] [<c0a4c694>] (driver_probe_device) from [<c0a4a3dc>] (bus_for_each_drv+0x58/0xb8)
[    2.205414] [<c0a4a3dc>] (bus_for_each_drv) from [<c0a4c024>] (__device_attach+0xd0/0x168)
[    2.213637] [<c0a4c024>] (__device_attach) from [<c0a4b1d0>] (bus_probe_device+0x84/0x8c)
[    2.221772] [<c0a4b1d0>] (bus_probe_device) from [<c0a4b72c>] (deferred_probe_work_func+0x84/0xc4)
[    2.230686] [<c0a4b72c>] (deferred_probe_work_func) from [<c03650a4>] (process_one_work+0x218/0x510)
[    2.239772] [<c03650a4>] (process_one_work) from [<c03660d8>] (worker_thread+0x2a8/0x5c0)
[    2.247908] [<c03660d8>] (worker_thread) from [<c036b348>] (kthread+0x148/0x150)
[    2.255265] [<c036b348>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[    2.262444] Exception stack(0xea965fb0 to 0xea965ff8)
[    2.267466] 5fa0:                                     00000000 00000000 00000000 00000000
[    2.275598] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.283729] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    2.290333] ---[ end trace ca5d506728a0581a ]---

devlink_free is complaining right here:

	WARN_ON(!list_empty(&devlink->port_list));

This happens because devlink_port_unregister is no longer done right
away in dsa_port_setup when a DSA_PORT_TYPE_USER has failed.
Vivien said about this change that:

    Also no need to call devlink_port_unregister from within dsa_port_setup
    as this step is inconditionally handled by dsa_port_teardown on error.

which is not really true. The devlink_port_unregister function _is_
being called unconditionally from within dsa_port_setup, but not for
this port that just failed, just for the previous ones which were set
up.

ports_teardown:
	for (i = 0; i < port; i++)
		dsa_port_teardown(&ds->ports[i]);

Initially I was tempted to fix this by extending the "for" loop to also
cover the port that failed during setup. But this could have potentially
unforeseen consequences unrelated to devlink_port or even other types of
ports than user ports, which I can't really test for. For example, if
for some reason devlink_port_register itself would fail, then
unconditionally unregistering it in dsa_port_teardown would not be a
smart idea. The list might go on.

So just make dsa_port_setup undo the setup it had done upon failure, and
let the for loop undo the work of setting up the previous ports, which
are guaranteed to be brought up to a consistent state.

Fixes: 955222ca ("net: dsa: use a single switch statement for port setup")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Take only FIB events that are happening in init_net into account. No other
namespaces are supported.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152 conflicts are the NAPI fixes in 'net' overlapping with
some tasklet stuff in net-next
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for reported issues for
  5.3-rc7

  Also included in here is the documentation for how we are handling
  hardware issues under embargo that everyone has finally agreed on, as
  well as a MAINTAINERS update for the suckers who agreed to handle the
  LICENSES/ files.

  All of these have been in linux-next last week with no reported
  issues"

* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  fsi: scom: Don't abort operations for minor errors
  vmw_balloon: Fix offline page marking with compaction
  VMCI: Release resource if the work is already queued
  Documentation/process: Embargoed hardware security issues
  lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
  mei: me: add Tiger Lake point LP device ID
  intel_th: pci: Add Tiger Lake support
  intel_th: pci: Add support for another Lewisburg PCH
  stm class: Fix a double free of stm_source_device
  MAINTAINERS: add entry for LICENSES and SPDX stuff
  fpga: altera-ps-spi: Fix getting of optional confd gpio

Pull USB fixes from Greg KH:
 "Here are some small USB fixes that have been in linux-next this past
  week for 5.3-rc7

  They fix the usual xhci, syzbot reports, and other small issues that
  have come up last week.

  All have been in linux-next with no reported issues"

* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: cdc-wdm: fix race between write and disconnect due to flag abuse
  usb: host: xhci: rcar: Fix typo in compatible string matching
  usb: host: xhci-tegra: Set DMA mask correctly
  USB: storage: ums-realtek: Whitelist auto-delink support
  USB: storage: ums-realtek: Update module parameter description for auto_delink_en
  usb: host: ohci: fix a race condition between shutdown and irq
  usb: hcd: use managed device resources
  typec: tcpm: fix a typo in the comparison of pdo_max_voltage
  usb-storage: Add new JMS567 revision to unusual_devs
  usb: chipidea: udc: don't do hardware access if gadget has stopped
  usbtmc: more sanity checking for packet size
  usb: udc: lpc32xx: silence fall-through warning

Pull networking fixes from David Miller:

 1) Fix some length checks during OGM processing in batman-adv, from
    Sven Eckelmann.

 2) Fix regression that caused netfilter conntrack sysctls to not be
    per-netns any more. From Florian Westphal.

 3) Use after free in netpoll, from Feng Sun.

 4) Guard destruction of pfifo_fast per-cpu qdisc stats with
    qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
    in pfifo_fast_enqueue().

 5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.

 6) Handle neigh events on internal ports correctly in nfp, from John
    Hurley.

 7) Clear SKB timestamp in NF flow table code so that it does not
    confuse fq scheduler. From Florian Westphal.

 8) taprio destroy can crash if it is invoked in a failure path of
    taprio_init(), because the list head isn't setup properly yet and
    the list del is unconditional. Perform the list add earlier to
    address this. From Vladimir Oltean.

 9) Make sure to reapply vlan filters on device up, in aquantia driver.
    From Dmitry Bogdanov.

10) sgiseeq driver releases DMA memory using free_page() instead of
    dma_free_attrs(). From Christophe JAILLET.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
  net: seeq: Fix the function used to release some memory in an error handling path
  enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
  net: bcmgenet: use ethtool_op_get_ts_info()
  tc-testing: don't hardcode 'ip' in nsPlugin.py
  net: dsa: microchip: add KSZ8563 compatibility string
  dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
  net: aquantia: fix out of memory condition on rx side
  net: aquantia: linkstate irq should be oneshot
  net: aquantia: reapply vlan filters on up
  net: aquantia: fix limit of vlan filters
  net: aquantia: fix removal of vlan 0
  net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
  taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
  taprio: Fix kernel panic in taprio_destroy
  net: dsa: microchip: fill regmap_config name
  rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
  net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
  amd-xgbe: Fix error path in xgbe_mod_init()
  netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
  mac80211: Correctly set noencrypt for PAE frames
  ...

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: centralize SERDES IRQ handling

Following Marek's work on the abstraction of the SERDES lanes mapping, this
series trades the .serdes_irq_setup and .serdes_irq_free callbacks for new
.serdes_irq_mapping, .serdes_irq_enable and .serdes_irq_status operations.

This has the benefit to limit the various SERDES implementations to simple
register accesses only; centralize the IRQ handling and mutex locking logic;
as well as reducing boilerplate in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.

This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.

This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.

At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6352_serdes_power_set helper is only used at one place, in
mv88e6352_serdes_power. Keep it simple and merge the two functions
together.

Use mv88e6xxx_serdes_get_lane instead of mv88e6352_port_has_serdes
to avoid moving code. No functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though 88E6352 has no dedicated lane for SERDES interfaces, it
uses a similar code as the other .serdes_get_lane implementations to
check the port's CMODE and ensure that SERDES operations are doable.

For consistency, implement mv88e6352_serdes_get_lane for the 88E6352
and similar switches which simply returns an unused 0xff lane address.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because the mapping between a SERDES interface and its lane is static,
we don't need to stick with negative error codes actually and we can
simply return 0 if there is no lane, just like the IRQ mapping.

This way we can keep a simple and intuitive API using unsigned lane
numbers while simplifying the implementations with single return
statements. Last but not least, fix the reverse chrismas tree in
mv88e6390x_serdes_get_lane.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current mv88e6xxx SERDES code checks for negative error code from
irq_find_mapping, while this function returns an unsigned integer. This
patch removes this dead code and simply returns 0 is no IRQ is found.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6352_serdes_irq_link helper is not checking for any error that
may occur during hardware accesses. Worst, the "up" boolean is set from
the potentially unused "status" variable, if read operations failed.

As done in mv88e6390_serdes_irq_link_sgmii, return right away and do
not call dsa_port_phylink_mac_change if an error occurred.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function 'hclge_restore_vlan_table':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8016:18: warning:
 variable 'qos' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 70a21490 ("net: hns3: reduce the parameters of some functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer reg_info is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 99cd149e ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.

Fix it now.

Rename the corresponding label to something more in line.

Fixes: 99cd149e ("sgiseeq: replace use of dma_cache_wback_inv")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer iter is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTL8125 uses a different register for VLAN offloading config,
therefore don't set bit RxVlan.

Fixes: f1bce4ad ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for x86:

   - Fix the bogus detection of 32bit user mode for uretprobes which
     caused corruption of the user return address resulting in
     application crashes. In the uprobes handler in_ia32_syscall() is
     obviously always returning false on a 64bit kernel. Use
     user_64bit_mode() instead which works correctly.

   - Prevent large page splitting when ftrace flips RW/RO on the kernel
     text which caused iTLB performance issues. Ftrace wants to be
     converted to text_poke() which avoids the problem, but for now
     allow large page preservation in the static protections check when
     the change request spawns a full large page.

   - Prevent arch_dynirq_lower_bound() from returning 0 when the IOAPIC
     is configured via device tree. In the device tree case the GSI 1:1
     mapping is meaningless therefore the lower bound which protects the
     GSI range on ACPI machines is irrelevant. Return the lower bound
     which the core hands to the function instead of blindly returning 0
     which causes the core to allocate the invalid virtual interupt
     number 0 which in turn prevents all drivers from allocating and
     requesting an interrupt.

   - Remove the bogus initialization of LDR and DFR in the 32bit bigsmp
     APIC driver. That uses physical destination mode where LDR/DFR are
     ignored, but the initialization and the missing clear of LDR caused
     the APIC to be left in a inconsistent state on kexec/reboot.

   - Clear LDR when clearing the APIC registers so the APIC is in a well
     defined state.

   - Initialize variables proper in the find_trampoline_placement()
     code.

   - Silence GCC( build warning for the real mode part of the build"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/cpa: Prevent large page split when ftrace flips RW on kernel text
  x86/build: Add -Wnoaddress-of-packed-member to REALMODE_CFLAGS, to silence GCC9 build warning
  x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
  x86/apic: Include the LDR when clearing out APIC registers
  x86/apic: Do not initialize LDR and DFR for bigsmp
  uprobes/x86: Fix detection of 32-bit user mode
  x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines

Pull perf fixes from Thomas Gleixner:
 "Two fixes for perf x86 hardware implementations:

   - Restrict the period on Nehalem machines to prevent perf from
     hogging the CPU

   - Prevent the AMD IBS driver from overwriting the hardwre controlled
     and pre-seeded reserved bits (0-6) in the count register which
     caused a sample bias for dispatched micro-ops"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/amd/ibs: Fix sample bias for dispatched micro-ops
  perf/x86/intel: Restrict period on Nehalem

Pull turbostat updates from Len Brown:
 "User-space turbostat (and x86_energy_perf_policy) patches.

  They are primarily bug fixes from users"

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: update version number
  tools/power turbostat: Add support for Hygon Fam 18h (Dhyana) RAPL
  tools/power turbostat: Fix caller parameter of get_tdp_amd()
  tools/power turbostat: Fix CPU%C1 display value
  tools/power turbostat: do not enforce 1ms
  tools/power turbostat: read from pipes too
  tools/power turbostat: Add Ice Lake NNPI support
  tools/power turbostat: rename has_hsw_msrs()
  tools/power turbostat: Fix Haswell Core systems
  tools/power turbostat: add Jacobsville support
  tools/power turbostat: fix buffer overrun
  tools/power turbostat: fix file descriptor leaks
  tools/power turbostat: fix leak of file descriptor on error return path
  tools/power turbostat: Make interval calculation per thread to reduce jitter
  tools/power turbostat: remove duplicate pc10 column
  tools/power x86_energy_perf_policy: Fix argument parsing
  tools/power: Fix typo in man page
  tools/power/x86: Enable compiler optimisations and Fortify by default
  tools/power x86_energy_perf_policy: Fix "uninitialized variable" warnings at -O2