The JC42 compatible thermal sensor on Kingston KSM32ES8/16ME DIMMs
(using Micron E-Die) is an ST Microelectronics STTS2004 (manufacturer
0x104a, device 0x2201). It does not keep the previously programmed
minimum, maximum and critical temperatures after system suspend and
resume (which is a shutdown / startup cycle for the JC42 temperature
sensor). This results in an alarm on system resume because the hardware
default for these values is 0°C (so any environment temperature greater
than 0°C will trigger the alarm).

Example before system suspend:
  jc42-i2c-0-1a
  Adapter: SMBus PIIX4 adapter port 0 at 0b00
  temp1:        +34.8°C  (low  =  +0.0°C)
                         (high = +85.0°C, hyst = +85.0°C)
                         (crit = +95.0°C, hyst = +95.0°C)

Example after system resume (without this change):
  jc42-i2c-0-1a
  Adapter: SMBus PIIX4 adapter port 0 at 0b00
  temp1:        +34.8°C  (low  =  +0.0°C)             ALARM (HIGH, CRIT)
                         (high =  +0.0°C, hyst =  +0.0°C)
                         (crit =  +0.0°C, hyst =  +0.0°C)

Apply the cached values from the JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER, JC42_REG_TEMP_CRITICAL and JC42_REG_SMBUS (where
the SMBUS register is not related to this issue but a side-effect of
using regcache_sync() during system resume with the previously
cached/programmed values. This fixes the alarm due to the hardware
defaults of 0°C because the previously applied limits (set by userspace)
are re-applied on system resume.

Fixes: 175c490c ("hwmon: (jc42) Add support for STTS2004 and AT30TSE004")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-3-martin.blumenstingl@googlemail.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Switch the jc42 driver to use an I2C regmap to access the registers.
Also move over to regmap's built-in caching instead of adding a
custom caching implementation. This works for JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER and JC42_REG_TEMP_CRITICAL as these values never
change except when explicitly written. The cache For JC42_REG_TEMP is
dropped (regmap can't cache it because it's volatile, meaning it can
change at any time) as well for simplicity and consistency with other
drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20221023213157.11078-2-martin.blumenstingl@googlemail.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Add support for reading and writing temperature sensor offsets
on the Aquacomputer D5 Next, Farbwerk 360, Octo and Quadro,
for which the needed offsets are known. Implemented by
Leonard Anderweit [1].

[1] https://github.com/aleksamagicka/aquacomputer_d5next-hwmon/pull/22

Originally-from: Leonard Anderweit <leonard.anderweit@gmail.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20221024151039.7222-1-savicaleksa83@gmail.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Commit c112d758 ("hwmon: OCC drivers are ARM-only") made the OCC
sensor drivers not selectable on powerpc64:

  These drivers are for a BMC inside PowerPC servers. The BMC runs on
  ARM hardware, so only propose the drivers on this architecture, unless
  build-testing.

... but we now have a powerpc64 BMC (still for a powerpc64 host), so
drop the `depends on` that excludes building for this platform.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20221024081527.3842565-1-jk@codeconstruct.com.auSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Add documentation for the Ampere(R)'s Altra(R) SMpro hwmon driver.
Signed-off-by: Thu Nguyen <thu@os.amperecomputing.com>
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20220929094321.770125-3-quan@os.amperecomputing.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This commit adds support for Ampere SMpro hwmon driver. This driver
supports accessing various CPU sensors provided by the SMpro co-processor
including temperature, power, voltages, and current.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20220929094321.770125-2-quan@os.amperecomputing.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Drop open-coded pattern: 'devm_regulator_get(), regulator_enable(),
add_action_or_reset(regulator_disable)' and use the
devm_regulator_get_enable() and drop the pointer to the regulator.
This simplifies code and makes it less tempting to add manual control
for the regulator which is also controlled by devm.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/7773541795f280db31dd981ffc21df8a630b794a.1666357434.git.mazziesaccount@gmail.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Drop open-coded pattern: 'devm_regulator_get(), regulator_enable(),
add_action_or_reset(regulator_disable)' and use the
devm_regulator_get_enable().
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/a1fa4364cbb775de25478117dd22dda0742089e3.1666357434.git.mazziesaccount@gmail.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

All these drivers have an i2c probe function which doesn't use the
"struct i2c_device_id *id" parameter, so they can trivially be
converted to the "probe_new" style of probe with a single argument.

This is part of an ongoing transition to single-argument i2c probe
functions. Old-style probe functions involve a call to i2c_match_id:
in drivers/i2c/i2c-core-base.c,

         /*
          * When there are no more users of probe(),
          * rename probe_new to probe.
          */
         if (driver->probe_new)
                 status = driver->probe_new(client);
         else if (driver->probe)
                 status = driver->probe(client,
                                        i2c_match_id(driver->id_table, client));
         else
                 status = -EINVAL;

Drivers which don't need the second parameter can be declared using
probe_new instead, avoiding the call to i2c_match_id. Drivers which do
can still be converted to probe_new-style, calling i2c_match_id
themselves (as is done currently for of_match_id).

This change was done using the following Coccinelle script, and fixed
up for whitespace changes:

@ rule1 @
identifier fn;
identifier client, id;
@@

- static int fn(struct i2c_client *client, const struct i2c_device_id *id)
+ static int fn(struct i2c_client *client)
{
...when != id
}

@ rule2 depends on rule1 @
identifier rule1.fn;
identifier driver;
@@

struct i2c_driver driver = {
-       .probe
+       .probe_new
                =
(
                   fn
|
-                  &fn
+                  fn
)
                ,
};
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20221011143309.3141267-1-steve@sk2.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Check there is a chip before using force_id parameter as there
is no value in registering a non-existent chip
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20221004210100.540120-3-ahmad@khalifa.wsSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Add parameter to ignore ACPI resource conflicts as an alternate to using
'acpi_enforce_resources=lax'.

Some BIOSes reserve resources and don't use them and the system wide
parameter may result in failures to certain drivers.
Signed-off-by: Ahmad Khalifa <ahmad@khalifa.ws>
Link: https://lore.kernel.org/r/20221004210100.540120-2-ahmad@khalifa.wsSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Don't populate the read-only const arrays names and watchdog_minors
on the stack but instead make them static const. Also makes the
object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221005152752.318493-1-colin.i.king@gmail.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

This reverts commit f35b5d7d.

It has been reported to cause huge performance regressions on some loads
(will-it-scale.per_process_ops, but also building the kernel with
clang).

The commit did speed up gcc builds by a small amount, so it's not an
unambiguous regression, but until the big regressions are understood,
let's revert it.
Reported-by: kernel test robot <yujie.liu@intel.com>
Link: https://lore.kernel.org/r/202210181535.7144dd15-yujie.liu@intel.comReported-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/lkml/Y1DNQaoPWxE%2BrGce@dev-arch.thelio-3990X/
Cc: Huang, Ying <ying.huang@intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yang Shi <shy828301@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently tpm transactions are executed unconditionally in
tpm_pm_suspend() function, which may lead to races with other tpm
accessors in the system.

Specifically, the hw_random tpm driver makes use of tpm_get_random(),
and this function is called in a loop from a kthread, which means it's
not frozen alongside userspace, and so can race with the work done
during system suspend:

  tpm tpm0: tpm_transmit: tpm_recv: error -52
  tpm tpm0: invalid TPM_STS.x 0xff, dumping stack for forensics
  CPU: 0 PID: 1 Comm: init Not tainted 6.1.0-rc5+ #135
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
  Call Trace:
   tpm_tis_status.cold+0x19/0x20
   tpm_transmit+0x13b/0x390
   tpm_transmit_cmd+0x20/0x80
   tpm1_pm_suspend+0xa6/0x110
   tpm_pm_suspend+0x53/0x80
   __pnp_bus_suspend+0x35/0xe0
   __device_suspend+0x10f/0x350

Fix this by calling tpm_try_get_ops(), which itself is a wrapper around
tpm_chip_start(), but takes the appropriate mutex.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/all/c5ba47ef-393f-1fba-30bd-1230d1b4b592@suse.cz/
Cc: stable@vger.kernel.org
Fixes: e891db1a ("tpm: turn on TPM on suspend for TPM 1.x")
[Jason: reworked commit message, added metadata]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull perf fix from Borislav Petkov:

 - Fix a use-after-free case where the perf pending task callback would
   see an already freed event

* tag 'perf_urgent_for_v6.1_rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix perf_pending_task() UaF

Pull timer fix from Borislav Petkov:

 - Revert a fix to RISC-V timers supposed to address an uncertainty
   whether clock events are received during S3 or not which locks up
   other RISC-V platforms. The issue will be fixed differently later.

* tag 'timers_urgent_for_v6.1_rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "clocksource/drivers/riscv: Events are stopped during CPU suspend"

Pull powerpc fixes from Michael Ellerman:

 - Fix oops in 32-bit BPF tail call tests

 - Add missing declaration for machine_check_early_boot()

Thanks to Christophe Leroy and Naveen N. Rao.

* tag 'powerpc-6.1-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Add missing declaration for machine_check_early_boot()
  powerpc/bpf/32: Fix Oops on tail call tests

Pull input fix from Dmitry Torokhov:

 - a fix for Raydium touchscreen driver to stop leaking memory when
   sending commands to the chip

* tag 'input-for-v6.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: raydium_ts_i2c - fix memory leak in raydium_i2c_send()

Pull i2c fixes from Wolfram Sang:
 "A power state fix in the core for ACPI devices, a regression fix
  regarding bus recovery for the cadence driver, a DMA handling fix for
  the imx driver, and two error path fixes (npcm7xx and qcom-geni)"

* tag 'i2c-for-6.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx: Only DMA messages with I2C_M_DMA_SAFE flag set
  i2c: qcom-geni: fix error return code in geni_i2c_gpi_xfer
  i2c: cadence: Fix regression with bus recovery
  i2c: Restore initial power state if probe fails
  i2c: npcm7xx: Fix error handling in npcm_i2c_init()

Pull dax fixes from Dan Williams:
 "A few bug fixes around the handling of "Soft Reserved" memory and
  memory tiering information.

  Linux is starting to enounter more real world systems that deploy an
  ACPI HMAT to describe different performance classes of memory, as well
  the "special purpose" (Linux "Soft Reserved") designation from EFI.

  These fixes result from that testing.

  It has all appeared in -next for a while with no known issues.

   - Fix duplicate overlapping device-dax instances for HMAT described
     "Soft Reserved" Memory

   - Fix missing node targets in the sysfs representation of memory
     tiers

   - Remove a confusing variable initialization"

* tag 'dax-fixes-6.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: Fix duplicate 'hmem' device registration
  ACPI: HMAT: Fix initiator registration for single-initiator systems
  ACPI: HMAT: remove unnecessary variable initialization

Pull block fixes from Jens Axboe:
 "Just a small NVMe merge for this week, fixing protection of the name
  space list, and a missing clear of a reserved field when unused"

* tag 'block-6.1-2022-12-02' of git://git.kernel.dk/linux:
  nvme: fix SRCU protection of nvme_ns_head list
  nvme-pci: clear the prp2 field when not used

Pull pin control fixes from Linus Walleij:
 "Three driver fixes. The Intel fix looks like the most important.

   - Fix a potential divide by zero in pinctrl-singe (OMAP and
     HiSilicon)

   - Disable IRQs on startup in the Mediatek driver. This is a classic,
     we should be looking out for this more.

   - Save and restore pins in 'direct IRQ' mode in the Intel driver,
     this works around firmware bugs"

* tag 'pinctrl-v6.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: intel: Save and restore pins in "direct IRQ" mode
  pinctrl: meditatek: Startup with the IRQs disabled
  pinctrl: single: Fix potential division by zero

Pull RISC-V fixes from Palmer Dabbelt:

 - build fix for the NR_CPUS Kconfig SBI version dependency

 - fixes to early memory initialization, to fix page permissions in EFI
   and post-initmem-free

 - build fix for the VDSO, to avoid trying to profile the VDSO functions

 - fixes for kexec crash handling, to fix multi-core and interrupt
   related initialization inside the crash kernel

 - fix for a race condition when handling multiple concurrect kernel
   stack overflows

* tag 'riscv-for-linus-6.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: kexec: Fixup crash_smp_send_stop without multi cores
  riscv: kexec: Fixup irq controller broken in kexec crash path
  riscv: mm: Proper page permissions after initmem free
  riscv: vdso: fix section overlapping under some conditions
  riscv: fix race when vmap stack overflow
  riscv: Sync efi page table's kernel mappings before switching
  riscv: Fix NR_CPUS range conditions

Pull MMC fixes from Ulf Hansson:
 "MMC core:
   - Fix ambiguous TRIM and DISCARD args
   - Fix removal of debugfs file for mmc_test

  MMC host:
   - mtk-sd: Add missing clk_disable_unprepare() in an error path
   - sdhci: Fix I/O voltage switch delay for UHS-I SD cards
   - sdhci-esdhc-imx: Fix CQHCI exit halt state check
   - sdhci-sprd: Fix voltage switch"

* tag 'mmc-v6.1-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-sprd: Fix no reset data and command after voltage switch
  mmc: sdhci: Fix voltage switch delay
  mmc: mtk-sd: Fix missing clk_disable_unprepare in msdc_of_clock_parse()
  mmc: mmc_test: Fix removal of debugfs file
  mmc: sdhci-esdhc-imx: correct CQHCI exit halt state check
  mmc: core: Fix ambiguous TRIM and DISCARD arg

Pull iommu fixes from Joerg Roedel:
 "Intel VT-d fixes:

   - IO/TLB flush fix

   - Various pci_dev refcount fixes"

* tag 'iommu-fixes-v6.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/vt-d: Fix PCI device refcount leak in dmar_dev_scope_init()
  iommu/vt-d: Fix PCI device refcount leak in has_external_pci()
  iommu/vt-d: Fix PCI device refcount leak in prq_event_thread()
  iommu/vt-d: Add a fix for devices need extra dtlb flush

The "force" argument to write_spec_ctrl_current() is currently ambiguous
as it does not guarantee the MSR write. This is due to the optimization
that writes to the MSR happen only when the new value differs from the
cached value.

This is fine in most cases, but breaks for S3 resume when the cached MSR
value gets out of sync with the hardware MSR value due to S3 resetting
it.

When x86_spec_ctrl_current is same as x86_spec_ctrl_base, the MSR write
is skipped. Which results in SPEC_CTRL mitigations not getting restored.

Move the MSR write from write_spec_ctrl_current() to a new function that
unconditionally writes to the MSR. Update the callers accordingly and
rename functions.

  [ bp: Rework a bit. ]

Fixes: caa0ff24 ("x86/bugs: Keep a per-CPU IA32_SPEC_CTRL value")
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/806d39b0bfec2fe8f50dc5446dff20f5bb24a959.1669821572.git.pawan.kumar.gupta@linux.intel.comSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There is a kmemleak when test the raydium_i2c_ts with bpf mock device:

  unreferenced object 0xffff88812d3675a0 (size 8):
    comm "python3", pid 349, jiffies 4294741067 (age 95.695s)
    hex dump (first 8 bytes):
      11 0e 10 c0 01 00 04 00                          ........
    backtrace:
      [<0000000068427125>] __kmalloc+0x46/0x1b0
      [<0000000090180f91>] raydium_i2c_send+0xd4/0x2bf [raydium_i2c_ts]
      [<000000006e631aee>] raydium_i2c_initialize.cold+0xbc/0x3e4 [raydium_i2c_ts]
      [<00000000dc6fcf38>] raydium_i2c_probe+0x3cd/0x6bc [raydium_i2c_ts]
      [<00000000a310de16>] i2c_device_probe+0x651/0x680
      [<00000000f5a96bf3>] really_probe+0x17c/0x3f0
      [<00000000096ba499>] __driver_probe_device+0xe3/0x170
      [<00000000c5acb4d9>] driver_probe_device+0x49/0x120
      [<00000000264fe082>] __device_attach_driver+0xf7/0x150
      [<00000000f919423c>] bus_for_each_drv+0x114/0x180
      [<00000000e067feca>] __device_attach+0x1e5/0x2d0
      [<0000000054301fc2>] bus_probe_device+0x126/0x140
      [<00000000aad93b22>] device_add+0x810/0x1130
      [<00000000c086a53f>] i2c_new_client_device+0x352/0x4e0
      [<000000003c2c248c>] of_i2c_register_device+0xf1/0x110
      [<00000000ffec4177>] of_i2c_notify+0x100/0x160
  unreferenced object 0xffff88812d3675c8 (size 8):
    comm "python3", pid 349, jiffies 4294741070 (age 95.692s)
    hex dump (first 8 bytes):
      22 00 36 2d 81 88 ff ff                          ".6-....
    backtrace:
      [<0000000068427125>] __kmalloc+0x46/0x1b0
      [<0000000090180f91>] raydium_i2c_send+0xd4/0x2bf [raydium_i2c_ts]
      [<000000001d5c9620>] raydium_i2c_initialize.cold+0x223/0x3e4 [raydium_i2c_ts]
      [<00000000dc6fcf38>] raydium_i2c_probe+0x3cd/0x6bc [raydium_i2c_ts]
      [<00000000a310de16>] i2c_device_probe+0x651/0x680
      [<00000000f5a96bf3>] really_probe+0x17c/0x3f0
      [<00000000096ba499>] __driver_probe_device+0xe3/0x170
      [<00000000c5acb4d9>] driver_probe_device+0x49/0x120
      [<00000000264fe082>] __device_attach_driver+0xf7/0x150
      [<00000000f919423c>] bus_for_each_drv+0x114/0x180
      [<00000000e067feca>] __device_attach+0x1e5/0x2d0
      [<0000000054301fc2>] bus_probe_device+0x126/0x140
      [<00000000aad93b22>] device_add+0x810/0x1130
      [<00000000c086a53f>] i2c_new_client_device+0x352/0x4e0
      [<000000003c2c248c>] of_i2c_register_device+0xf1/0x110
      [<00000000ffec4177>] of_i2c_notify+0x100/0x160

After BANK_SWITCH command from i2c BUS, no matter success or error
happened, the tx_buf should be freed.

Fixes: 3b384bd6 ("Input: raydium_ts_i2c - do not split tx transactions")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Link: https://lore.kernel.org/r/20221202103412.2120169-1-zhangxiaoxu5@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull sound fixes from Takashi Iwai:
 "Likely the last piece for 6.1; the only significant fixes are ASoC
  core ops fixes, while others are device-specific (rather minor) fixes
  in ASoC and FireWire drivers.

  All appear safe enough to take as a late stage material"

* tag 'sound-6.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: dice: fix regression for Lexicon I-ONIX FW810S
  ASoC: cs42l51: Correct PGA Volume minimum value
  ASoC: ops: Correct bounds check for second channel on SX controls
  ASoC: tlv320adc3xxx: Fix build error for implicit function declaration
  ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()
  ASoC: ops: Fix bounds check for _sx controls
  ASoC: fsl_micfil: explicitly clear CHnF flags
  ASoC: fsl_micfil: explicitly clear software reset bit

Pull drm fixes from Dave Airlie:
 "Things do seem to have finally settled down, just four i915 and one
  amdgpu this week. Probably won't have much for next week if you do
  push rc8 out.

  i915:
   - Fix dram info readout
   - Remove non-existent pipes from bigjoiner pipe mask
   - Fix negative value passed as remaining time
   - Never return 0 if not all requests retired

  amdgpu:
   - VCN fix for vangogh"

* tag 'drm-fixes-2022-12-02' of git://anongit.freedesktop.org/drm/drm:
  drm/amdgpu: enable Vangogh VCN indirect sram mode
  drm/i915: Never return 0 if not all requests retired
  drm/i915: Fix negative value passed as remaining time
  drm/i915: Remove non-existent pipes from bigjoiner pipe mask
  drm/i915/mtl: Fix dram info readout

Pull misc hotfixes from Andrew Morton:
 "15 hotfixes,  11 marked cc:stable.

  Only three or four of the latter address post-6.0 issues, which is
  hopefully a sign that things are converging"

* tag 'mm-hotfixes-stable-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  revert "kbuild: fix -Wimplicit-function-declaration in license_is_gpl_compatible"
  Kconfig.debug: provide a little extra FRAME_WARN leeway when KASAN is enabled
  drm/amdgpu: temporarily disable broken Clang builds due to blown stack-frame
  mm/khugepaged: invoke MMU notifiers in shmem/file collapse paths
  mm/khugepaged: fix GUP-fast interaction by sending IPI
  mm/khugepaged: take the right locks for page table retraction
  mm: migrate: fix THP's mapcount on isolation
  mm: introduce arch_has_hw_nonleaf_pmd_young()
  mm: add dummy pmd_young() for architectures not having it
  mm/damon/sysfs: fix wrong empty schemes assumption under online tuning in damon_sysfs_set_schemes()
  tools/vm/slabinfo-gnuplot: use "grep -E" instead of "egrep"
  nilfs2: fix NULL pointer dereference in nilfs_palloc_commit_free_entry()
  hugetlb: don't delete vma_lock in hugetlb MADV_DONTNEED processing
  madvise: use zap_page_range_single for madvise dontneed
  mm: replace VM_WARN_ON to pr_warn if the node is offline with __GFP_THISNODE

The V4L2_MEMORY_USERPTR interface is long deprecated and shouldn't be
used (and is discouraged for any modern v4l drivers).  And Seth Jenkins
points out that the fallback to VM_PFNMAP/VM_IO is fundamentally racy
and dangerous.

Note that it's not even a case that should trigger, since any normal
user pointer logic ends up just using the pin_user_pages_fast() call
that does the proper page reference counting.  That's not the problem
case, only if you try to use special device mappings do you have any
issues.

Normally I'd just remove this during the merge window, but since Seth
pointed out the problem cases, we really want to know as soon as
possible if there are actually any users of this odd special case of a
legacy interface.  Neither Hans nor Mauro seem to think that such
mis-uses of the old legacy interface should exist.  As Mauro says:

 "See, V4L2 has actually 4 streaming APIs:
        - Kernel-allocated mmap (usually referred simply as just mmap);
        - USERPTR mmap;
        - read();
        - dmabuf;

  The USERPTR is one of the oldest way to use it, coming from V4L
  version 1 times, and by far the least used one"

And Hans chimed in on the USERPTR interface:

 "To be honest, I wouldn't mind if it goes away completely, but that's a
  bit of a pipe dream right now"

but while removing this legacy interface entirely may be a pipe dream we
can at least try to remove the unlikely (and actively broken) case of
using special device mappings for USERPTR accesses.

This replaces it with a WARN_ONCE() that we can remove once we've
hopefully confirmed that no actual users exist.

NOTE! Longer term, this means that a 'struct frame_vector' only ever
contains proper page pointers, and all the games we have with converting
them to pages can go away (grep for 'frame_vector_to_pages()' and the
uses of 'vec->is_pfns').  But this is just the first step, to verify
that this code really is all dead, and do so as quickly as possible.
Reported-by: Seth Jenkins <sethjenkins@google.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NVMe fixes from Christoph:

"nvme fixes for Linux 6.1

 - fix SRCU protection of nvme_ns_head list (Caleb Sander)
 - clear the prp2 field when not used (Lei Rao)"

* tag 'nvme-6.1-2022-01-02' of git://git.infradead.org/nvme:
  nvme: fix SRCU protection of nvme_ns_head list
  nvme-pci: clear the prp2 field when not used

for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.

If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the error path to avoid reference count leak.

Fixes: 2e455289 ("iommu/vt-d: Unify the way to process DMAR device scope array")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221121113649.190393-3-wangxiongfeng2@huawei.comSigned-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.

If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() before 'return true' to avoid reference count leak.

Fixes: 89a6079d ("iommu/vt-d: Force IOMMU on for platform opt in hint")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221121113649.190393-2-wangxiongfeng2@huawei.comSigned-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

As comment of pci_get_domain_bus_and_slot() says, it returns a pci device
with refcount increment, when finish using it, the caller must decrease
the reference count by calling pci_dev_put(). So call pci_dev_put() after
using the 'pdev' to avoid refcount leak.

Besides, if the 'pdev' is null or intel_svm_prq_report() returns error,
there is no need to trace this fault.

Fixes: 06f4b8d0 ("iommu/vt-d: Remove unnecessary SVA data accesses in page fault path")
Suggested-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221119144028.2452731-1-yangyingliang@huawei.comSigned-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

QAT devices on Intel Sapphire Rapids and Emerald Rapids have a defect in
address translation service (ATS). These devices may inadvertently issue
ATS invalidation completion before posted writes initiated with
translated address that utilized translations matching the invalidation
address range, violating the invalidation completion ordering.

This patch adds an extra device TLB invalidation for the affected devices,
it is needed to ensure no more posted writes with translated address
following the invalidation completion. Therefore, the ordering is
preserved and data-corruption is prevented.

Device TLBs are invalidated under the following six conditions:
1. Device driver does DMA API unmap IOVA
2. Device driver unbind a PASID from a process, sva_unbind_device()
3. PASID is torn down, after PASID cache is flushed. e.g. process
exit_mmap() due to crash
4. Under SVA usage, called by mmu_notifier.invalidate_range() where
VM has to free pages that were unmapped
5. userspace driver unmaps a DMA buffer
6. Cache invalidation in vSVA usage (upcoming)

For #1 and #2, device drivers are responsible for stopping DMA traffic
before unmap/unbind. For #3, iommu driver gets mmu_notifier to
invalidate TLB the same way as normal user unmap which will do an extra
invalidation. The dTLB invalidation after PASID cache flush does not
need an extra invalidation.

Therefore, we only need to deal with #4 and #5 in this patch. #1 is also
covered by this patch due to common code path with #5.
Tested-by: Yuzhang Luo <yuzhang.luo@intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Link: https://lore.kernel.org/r/20221130062449.1360063-1-jacob.jun.pan@linux.intel.comSigned-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Merge tag 'amd-drm-fixes-6.1-2022-12-01' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-6.1-2022-12-01:

amdgpu:
- VCN fix for vangogh
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221201202015.5931-1-alexander.deucher@amd.com

Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.

This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.

Fixes: 4544b9f2 ("dma-mapping: Add vmap checks to dma_map_single()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Fix to return a negative error code from the gi2c->err instead of
0.

Fixes: d8703554 ("i2c: qcom-geni: Add support for GPI DMA")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Reviewed-by: Tommaso Merciai <tommaso.merciai@amarulasoluitons.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>