- 07 Mar, 2016 24 commits
-
-
Gerhard Uttenthaler authored
[ Upstream commit 90cfde46 ] This patch fixes the problem that more CAN messages could be sent to the interface as could be send on the CAN bus. This was more likely for slow baud rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under heavy TX load this produced another bulk transfer without checking the free_slots variable and hence caused the overflow in the interface. Signed-off-by:
Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com>
-
Lisa Du authored
[ Upstream commit 7a64cd88 ] There's one point was missed in the patch commit da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes."). When configure BINDER_IPC_32BIT, the size of binder_uintptr_t was 32bits, but size of void * is 64bit on 64bit system. Correct it here. Signed-off-by:
Lisa Du <cldu@marvell.com> Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Fixes: da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes.") Cc: <stable@vger.kernel.org> Acked-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Nishanth Menon authored
[ Upstream commit 000e0949 ] Thermal hook gpio_fan_get_cur_state is only interested in knowing the current speed index that was setup in the system, this is already available as part of fan_data->speed_index which is always set by set_fan_speed. Using get_fan_speed_index is useful when we have no idea about the fan speed configuration (for example during fan_ctrl_init). When thermal framework invokes gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state especially in a polled configuration for thermal governor, we basically hog the i2c interface to the extent that other functions fail to get any traffic out :(. Instead, just provide the last state set in the driver - since the gpio fan driver is responsible for the fan state immaterial of override, the fan_data->speed_index should accurately reflect the state. Fixes: b5cf88e4 ("(gpio-fan): Add thermal control hooks") Reported-by:
Tony Lindgren <tony@atomide.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Eduardo Valentin <edubezval@gmail.com> Signed-off-by:
Nishanth Menon <nm@ti.com> Cc: stable@vger.kernel.org Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Peter Rosin authored
[ Upstream commit acc14694 ] Make the divisor signed as DIV_ROUND_CLOSEST is undefined for negative dividends when the divisor is unsigned. Signed-off-by:
Peter Rosin <peda@axentia.se> Cc: stable@vger.kernel.org Signed-off-by:
-
Alexandra Yates authored
[ Upstream commit f5bdd66c ] This patch complements the list of device IDs previously added for lewisburg sata. Signed-off-by:
Alexandra Yates <alexandra.yates@linux.intel.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Alexandra Yates authored
[ Upstream commit 56e74338 ] Adding Intel codename Lewisburg platform device IDs for SATA. Signed-off-by:
-
Alexandra Yates authored
[ Upstream commit 4d92f009 ] This change was to preserve the ascending order of device IDs. There was an exception with the first two Lewisburg device IDs to keep all device IDs of the same kind grouped by code name. Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit d061c1ca ] Thomas reports: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05c6 ProdID=6001 Rev=00.00 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber=1234567890ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Cc: <stable@vger.kernel.org> Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Ken Lin authored
[ Upstream commit 6627ae19 ] Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards. Signed-off-by:
Ken Lin <ken.lin@advantech.com.tw> Signed-off-by:
Akshay Bhat <akshay.bhat@timesys.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Andrey Skvortsov authored
[ Upstream commit 3158a8d4 ] $ lsusb: Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option $ usb-devices: T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 2 P: Vendor=1e0e ProdID=9001 Rev= 2.32 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) The last interface (6) is used for Android Composite ADB interface. Serial port layout: 0: QCDM/DIAG 1: NMEA 2: AT 3: AT/PPP 4: audio Signed-off-by:
Andrey Skvortsov <andrej.skvortzov@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Benjamin Coddington authored
[ Upstream commit d9dfd8d7 ] In the case where d_add_unique() finds an appropriate alias to use it will have already incremented the reference count. An additional dget() to swap the open context's dentry is unnecessary and will leak a reference. Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Fixes: 275bb307 ("NFSv4: Move dentry instantiation into the NFSv4-...") Cc: stable@vger.kernel.org # 3.10+ Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
John Youn authored
[ Upstream commit c4509601 ] The assignement of EP transfer resources was not handled properly in the dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") previously fixed one aspect of this where resources may be exhausted with multiple calls to SET_INTERFACE. However, it introduced an issue where composite devices with multiple interfaces can be assigned the same transfer resources for different endpoints. This patch solves both issues. The assignment of transfer resources cannot perfectly follow the data book due to the fact that the controller driver does not have all knowledge of the configuration in advance. It is given this information piecemeal by the composite gadget framework after every SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook programming model in this scenario can cause errors. For two reasons: 1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple interfaces. 2) The databook does not mention doing more DEPXFERCFG for new endpoint on alt setting (8.1.6). The following simplified method is used instead: All hardware endpoints can be assigned a transfer resource and this setting will stay persistent until either a core reset or hibernation. So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for every hardware endpoint as well. We are guaranteed that there are as many transfer resources as endpoints. This patch triggers off of the calling dwc3_gadget_start_config() for EP0-out, which always happens first, and which should only happen in one of the above conditions. Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") Cc: <stable@vger.kernel.org> # v3.2+ Reported-by:
Ravi Babu <ravibabu@ti.com> Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org> Signed-off-by:
-
Hans Verkuil authored
[ Upstream commit 0ba4581c ] The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70 again after it has already been cleared. Instead it should use the cached irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since this has already been done. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Cc: <stable@vger.kernel.org> # for v3.14 and up Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
[ Upstream commit 4d8c8bd6 ] Occasionaly PV guests would crash with: pciback 0000:00:00.1: Xen PCI mapped GSI0 to IRQ16 BUG: unable to handle kernel paging request at 0000000d1a8c0be0 .. snip.. <ffffffff8139ce1b>] find_next_bit+0xb/0x10 [<ffffffff81387f22>] cpumask_next_and+0x22/0x40 [<ffffffff813c1ef8>] pci_device_probe+0xb8/0x120 [<ffffffff81529097>] ? driver_sysfs_add+0x77/0xa0 [<ffffffff815293e4>] driver_probe_device+0x1a4/0x2d0 [<ffffffff813c1ddd>] ? pci_match_device+0xdd/0x110 [<ffffffff81529657>] __device_attach_driver+0xa7/0xb0 [<ffffffff815295b0>] ? __driver_attach+0xa0/0xa0 [<ffffffff81527622>] bus_for_each_drv+0x62/0x90 [<ffffffff8152978d>] __device_attach+0xbd/0x110 [<ffffffff815297fb>] device_attach+0xb/0x10 [<ffffffff813b75ac>] pci_bus_add_device+0x3c/0x70 [<ffffffff813b7618>] pci_bus_add_devices+0x38/0x80 [<ffffffff813dc34e>] pcifront_scan_root+0x13e/0x1a0 [<ffffffff817a0692>] pcifront_backend_changed+0x262/0x60b [<ffffffff814644c6>] ? xenbus_gather+0xd6/0x160 [<ffffffff8120900f>] ? put_object+0x2f/0x50 [<ffffffff81465c1d>] xenbus_otherend_changed+0x9d/0xa0 [<ffffffff814678ee>] backend_changed+0xe/0x10 [<ffffffff81463a28>] xenwatch_thread+0xc8/0x190 [<ffffffff810f22f0>] ? woken_wake_function+0x10/0x10 which was the result of two things: When we call pci_scan_root_bus we would pass in 'sd' (sysdata) pointer which was an 'pcifront_sd' structure. However in the pci_device_add it expects that the 'sd' is 'struct sysdata' and sets the dev->node to what is in sd->node (offset 4): set_dev_node(&dev->dev, pcibus_to_node(bus)); __pcibus_to_node(const struct pci_bus *bus) { const struct pci_sysdata *sd = bus->sysdata; return sd->node; } However our structure was pcifront_sd which had nothing at that offset: struct pcifront_sd { int domain; /* 0 4 */ /* XXX 4 bytes hole, try to pack */ struct pcifront_device * pdev; /* 8 8 */ } That is an hole - filled with garbage as we used kmalloc instead of kzalloc (the second problem). This patch fixes the issue by: 1) Use kzalloc to initialize to a well known state. 2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That way access to the 'node' will access the right offset. Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: <stable@vger.kernel.org> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
[ Upstream commit d52a2481 ] commit 8d47065f upstream. Commit 408fb0e5 (xen/pciback: Don't allow MSI-X ops if PCI_COMMAND_MEMORY is not set) prevented enabling MSI-X on passed-through virtual functions, because it checked the VF for PCI_COMMAND_MEMORY but this is not a valid bit for VFs. Instead, check the physical function for PCI_COMMAND_MEMORY. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
[ Upstream commit 408fb0e5 ] commit f598282f ("PCI: Fix the NIU MSI-X problem in a better way") teaches us that dealing with MSI-X can be troublesome. Further checks in the MSI-X architecture shows that if the PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we may not be able to access the BAR (since they are memory regions). Since the MSI-X tables are located in there.. that can lead to us causing PCIe errors. Inhibit us performing any operation on the MSI-X unless the MEMORY bit is set. Note that Xen hypervisor with: "x86/MSI-X: access MSI-X table only after having enabled MSI-X" will return: xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3! When the generic MSI code tries to setup the PIRQ without MEMORY bit set. Which means with later versions of Xen (4.6) this patch is not neccessary. This is part of XSA-157 CC: stable@vger.kernel.org Reviewed-by:
-
Konrad Rzeszutek Wilk authored
[ Upstream commit 5e0ce145 ] The guest sequence of: a) XEN_PCI_OP_enable_msix b) XEN_PCI_OP_enable_msix results in hitting an NULL pointer due to using freed pointers. The device passed in the guest MUST have MSI-X capability. The a) constructs and SysFS representation of MSI and MSI groups. The b) adds a second set of them but adding in to SysFS fails (duplicate entry). 'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that in a) pdev->msi_irq_groups is still set) and also free's ALL of the MSI-X entries of the device (the ones allocated in step a) and b)). The unwind code: 'free_msi_irqs' deletes all the entries and tries to delete the pdev->msi_irq_groups (which hasn't been set to NULL). However the pointers in the SysFS are already freed and we hit an NULL pointer further on when 'strlen' is attempted on a freed pointer. The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard against that. The check for msi_enabled is not stricly neccessary. This is part of XSA-157 CC: stable@vger.kernel.org Reviewed-by:
-
Konrad Rzeszutek Wilk authored
[ Upstream commit 4cf5aa2f ] commit d159457b upstream. Commit 8135cf8b (xen/pciback: Save xen_pci_op commands before processing it) broke enabling MSI-X because it would never copy the resulting vectors into the response. The number of vectors requested was being overwritten by the return value (typically zero for success). Save the number of vectors before processing the op, so the correct number of vectors are copied afterwards. Signed-off-by:
-
Konrad Rzeszutek Wilk authored
[ Upstream commit 8135cf8b ] Double fetch vulnerabilities that happen when a variable is fetched twice from shared memory but a security check is only performed the first time. The xen_pcibk_do_op function performs a switch statements on the op->cmd value which is stored in shared memory. Interestingly this can result in a double fetch vulnerability depending on the performed compiler optimization. This patch fixes it by saving the xen_pci_op command before processing it. We also use 'barrier' to make sure that the compiler does not perform any optimization. This is part of XSA155. CC: stable@vger.kernel.org Reviewed-by:
-
Sasha Levin authored
[ Upstream commit 5e56276e ] The firmware can perform a scheduled scan with not matchsets passed, but it can't send notification that results were found. Since the userspace then cannot know when we got new results and the firmware wouldn't trigger a wake in case we are sleeping, it's better not to allow scans without matchsets. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=110831 Cc: <stable@vger.kernel.org> [3.17+] Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> [SL: Backport to 4.1] Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 287e6611 ] As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not work correctly in compat mode with libata. I have investigated the issue further and found multiple problems that all appeared with the same commit that originally introduced HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy a 'long' variable containing either 0 or 1 to user space. The problems with this are: * On big-endian machines, this will always write a zero because it stores the wrong byte into user space. * In compat mode, the upper three bytes of the variable are updated by the compat_hdio_ioctl() function, but they now contain uninitialized stack data. * The hdparm tool calling this ioctl uses a 'static long' variable to store the result. This means at least the upper bytes are initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT would fill them with data that remains stale when the low byte is overwritten. Fortunately libata doesn't implement any of the affected ioctl commands, so this would only happen when we query both an IDE and an ATA device in the same command such as "hdparm -N -c /dev/hda /dev/sda" * The libata code for unknown reasons started using ATA_IOC_GET_IO32 and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT, while the ioctl commands that were added later use the normal HDIO_* names. This is harmless but rather confusing. This addresses all four issues by changing the code to use put_user() on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem does, and by clarifying the names of the ioctl commands. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reported-by:
Soohoon Lee <Soohoon.Lee@f5.com> Tested-by:
-
Christoph Hellwig authored
[ Upstream commit 50ab8ec7 ] See http: //www.infradead.org/rpr.html X-Evolution-Source: 1451162204.2173.11@leira.trondhjem.org Content-Transfer-Encoding: 8bit Mime-Version: 1.0 We support OFFSET_MAX just fine, so don't round down below it. Also switch to using min_t to make the helper more readable. Signed-off-by:
Christoph Hellwig <hch@lst.de> Fixes: 433c9237 ("NFS: Clean up nfs_size_to_loff_t()") Cc: stable@vger.kernel.org # 2.6.23+ Signed-off-by:
-
Juergen Gross authored
[ Upstream commit f285aa8d ] When adding a new frontend to xen-scsiback don't decrement the number of active frontends in case of no error. Doing so results in a failure when trying to remove the xen-pvscsi nexus even if no domain is using it. Signed-off-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
-
David Ahern authored
[ Upstream commit c8ad7063 ] Building perf out of kernel tree is currently broken because the MANIFEST file refers to kernel files that have been removed. With this patch make perf-targz-src-pkg succeeds as does building perf using the generated tarfile. Signed-off-by:
David Ahern <david.ahern@oracle.com> Link: http://lkml.kernel.org/r/1433526173-172332-1-git-send-email-david.ahern@oracle.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
- 06 Mar, 2016 8 commits
-
-
Nicholas Bellinger authored
The linux-4.1.y specific patch to fix a previous v4.1 UNIT_ATTENTION read-copy-update conversion regression: commit 35afa656 Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Wed Sep 23 07:49:26 2015 +0000 target: Fix v4.1 UNIT_ATTENTION se_node_acl->device_list[] NULL pointer introduced the following compile warning: drivers/target/target_core_pr.c: In function ‘core_scsi3_pr_seq_non_holder’: drivers/target/target_core_pr.c:332:3: warning: ‘return’ with no value, in function returning non-void [-Wreturn-type] Go ahead and fix this up to always returning zero when no ACL device list exists within core_scsi3_pr_seq_non_holder(). Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 310d3d31 upstream. This patch fixes a race between setting of SCF_SEND_DELAYED_TAS in transport_send_task_abort(), and check of the same bit in transport_check_aborted_status(). It adds a __transport_check_aborted_status() version that is used by target_execute_cmd() when se_cmd->t_state_lock is held, and a transport_check_aborted_status() wrapper for all other existing callers. Also, it handles the case where the check happens before transport_send_task_abort() gets called. For this, go ahead and set SCF_SEND_DELAYED_TAS early when necessary, and have transport_send_task_abort() send the abort. Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 0f4a9431 upstream. To address the bug where fabric driver level shutdown of se_cmd occurs at the same time when TMR CMD_T_ABORTED is happening resulting in a -1 ->cmd_kref, this patch adds a CMD_T_FABRIC_STOP bit that is used to determine when TMR + driver I_T nexus shutdown is happening concurrently. It changes target_sess_cmd_list_set_waiting() to obtain se_cmd->cmd_kref + set CMD_T_FABRIC_STOP, and drop local reference in target_wait_for_sess_cmds() and invoke extra target_put_sess_cmd() during Task Aborted Status (TAS) when necessary. Also, it adds a new target_wait_free_cmd() wrapper around transport_wait_for_tasks() for the special case within transport_generic_free_cmd() to set CMD_T_FABRIC_STOP, and is now aware of CMD_T_ABORTED + CMD_T_TAS status bits to know when an extra transport_put_cmd() during TAS is required. Note transport_generic_free_cmd() is expected to block on cmd->cmd_wait_comp in order to follow what iscsi-target expects during iscsi_conn context se_cmd shutdown. Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by:
Nicholas Bellinger <nab@daterainc.com> Signed-off-by:
-
Nicholas Bellinger authored
commit ebde1ca5 upstream. This patch fixes a bug in TMR task aborted status (TAS) handling when multiple sessions are connected to the same target WWPN endpoint and se_node_acl descriptor, resulting in TASK_ABORTED status to not be generated for aborted se_cmds on the remote port. This is due to core_tmr_handle_tas_abort() incorrectly comparing se_node_acl instead of se_session, for which the multi-session case is expected to be sharing the same se_node_acl. Instead, go ahead and update core_tmr_handle_tas_abort() to compare tmr_sess + cmd->se_sess in order to determine if the LUN_RESET was received on a different I_T nexus, and TASK_ABORTED status response needs to be generated. Reviewed-by:
-
Nicholas Bellinger authored
commit febe562c upstream. This patch fixes a NULL pointer se_cmd->cmd_kref < 0 refcount bug during TMR LUN_RESET with active se_cmd I/O, that can be triggered during se_cmd descriptor shutdown + release via core_tmr_drain_state_list() code. To address this bug, add common __target_check_io_state() helper for ABORT_TASK + LUN_RESET w/ CMD_T_COMPLETE checking, and set CMD_T_ABORTED + obtain ->cmd_kref for both cases ahead of last target_put_sess_cmd() after TFO->aborted_task() -> transport_cmd_finish_abort() callback has completed. It also introduces SCF_ACK_KREF to determine when transport_cmd_finish_abort() needs to drop the second extra reference, ahead of calling target_put_sess_cmd() for the final kref_put(&se_cmd->cmd_kref). It also updates transport_cmd_check_stop() to avoid holding se_cmd->t_state_lock while dropping se_cmd device state via target_remove_from_state_list(), now that core_tmr_drain_state_list() is holding the se_device lock while checking se_cmd state from within TMR logic. Finally, move transport_put_cmd() release of SGL + TMR + extended CDB memory into target_free_cmd_mem() in order to avoid potential resource leaks in TMR ABORT_TASK + LUN_RESET code-paths. Also update target_release_cmd_kref() accordingly. Reviewed-by:
Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by:
-
Jan Engelhardt authored
[ Upstream commit d94e5a61 ] target_core_sbc's compare_and_write functionality suffers from taking data at the wrong memory location when writing a CAW request to disk when a SGL offset is non-zero. This can happen with loopback and vhost-scsi fabric drivers when SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers. Given the following sample LIO subtopology, % targetcli ls /loopback/ o- loopback ................................. [1 Target] o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3] o- luns ................................... [2 LUNs] o- lun0 ................ [iblock/ram0 (/dev/ram0)] o- lun1 ................ [iblock/ram1 (/dev/ram1)] % lsscsi -g [3:0:1:0] disk LIO-ORG IBLOCK 4.0 /dev/sdc /dev/sg3 [3:0:1:1] disk LIO-ORG IBLOCK 4.0 /dev/sdd /dev/sg4 the following bug can be observed in Linux 4.3 and 4.4~rc1: % perl -e 'print chr$_ for 0..255,reverse 0..255' >rand % perl -e 'print "\0" x 512' >zero % cat rand >/dev/sdd % sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd % sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd Miscompare reported % hexdump -Cn 512 /dev/sdd 00000000 0f 0e 0d 0c 0b 0a 09 08 07 06 05 04 03 02 01 00 00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 * 00000200 Rather than writing all-zeroes as instructed with the -D file, it corrupts the data in the sector by splicing some of the original bytes in. The page of the first entry of cmd->t_data_sg includes the CDB, and sg->offset is set to a position past the CDB. I presume that sg->offset is also the right choice to use for subsequent sglist members. Signed-off-by:
Jan Engelhardt <jengelh@netitwork.de> Tested-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Nicholas Bellinger authored
[ Upstream commit 057085e5 ] This patch addresses a race + use after free where the first stage of COMPARE_AND_WRITE in compare_and_write_callback() is rescheduled after the backend sends the secondary WRITE, resulting in second stage compare_and_write_post() callback completing in target_complete_ok_work() before the first can return. Because current code depends on checking se_cmd->se_cmd_flags after return from se_cmd->transport_complete_callback(), this results in first stage having SCF_COMPARE_AND_WRITE_POST set, which incorrectly falls through into second stage CAW processing code, eventually triggering a NULL pointer dereference due to use after free. To address this bug, pass in a new *post_ret parameter into se_cmd->transport_complete_callback(), and depend upon this value instead of ->se_cmd_flags to determine when to return or fall through into ->queue_status() code for CAW. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
-
Nicholas Bellinger authored
[ Upstream commit ca82c2bd ] This patch addresses a case where iscsi_target_do_tx_login_io() fails sending the last login response PDU, after the RX/TX threads have already been started. The case centers around iscsi_target_rx_thread() not invoking allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs from the failure path, resulting in RX thread hanging indefinately on iscsi_conn->rx_login_comp. Note this bug is a regression introduced by: commit e5419865 Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Wed Jul 22 23:14:19 2015 -0700 iscsi-target: Fix iscsit_start_kthreads failure OOPs To address this bug, complete ->rx_login_complete for good measure in the failure path, and immediately return from RX thread context if connection state did not actually reach full feature phase (TARG_CONN_STATE_LOGGED_IN). Cc: Sagi Grimberg <sagig@mellanox.com> Cc: <stable@vger.kernel.org> # v3.10+ Signed-off-by:
-
- 04 Mar, 2016 8 commits
-
-
Sasha Levin authored
Signed-off-by: -
Neil Horman authored
[ Upstream commit d9749fb5 ] Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in its size computation, observing that the current method never guaranteed that the hashsize (measured in number of entries) would be a power of two, which the input hash function for that table requires. The root cause of the problem is that two values need to be computed (one, the allocation order of the storage requries, as passed to __get_free_pages, and two the number of entries for the hash table). Both need to be ^2, but for different reasons, and the existing code is simply computing one order value, and using it as the basis for both, which is wrong (i.e. it assumes that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not). To fix this, we change the logic slightly. We start by computing a goal allocation order (which is limited by the maximum size hash table we want to support. Then we attempt to allocate that size table, decreasing the order until a successful allocation is made. Then, with the resultant successful order we compute the number of buckets that hash table supports, which we then round down to the nearest power of two, giving us the number of entries the table actually supports. I've tested this locally here, using non-debug and spinlock-debug kernels, and the number of entries in the hashtable consistently work out to be powers of two in all cases. Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> CC: Dmitry Vyukov <dvyukov@google.com> CC: Vladislav Yasevich <vyasevich@gmail.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Dmitry V. Levin authored
[ Upstream commit b5f05492 ] The value passed by unix_diag_get_exact to unix_lookup_by_ino has type __u32, but unix_lookup_by_ino's argument ino has type int, which is not a problem yet. However, when ino is compared with sock_i_ino return value of type unsigned long, ino is sign extended to signed long, and this results to incorrect comparison on 64-bit architectures for inode numbers greater than INT_MAX. This bug was found by strace test suite. Fixes: 5d3cae8b ("unix_diag: Dumping exact socket core") Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Anton Protopopov authored
[ Upstream commit a97eb33f ] An error response from a RTM_GETNETCONF request can return the positive error value EINVAL in the struct nlmsgerr that can mislead userspace. Signed-off-by:
Anton Protopopov <a.s.protopopov@gmail.com> Acked-by:
-
Xin Long authored
[ Upstream commit deed49df ] Since the gc of ipv4 route was removed, the route cached would has no chance to be removed, and even it has been timeout, it still could be used, cause no code to check it's expires. Fix this issue by checking and removing route cache when we get route. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Guillaume Nault authored
[ Upstream commit 29e73269 ] Drop reference on the relay_po socket when __pppoe_xmit() succeeds. This is already handled correctly in the error path. Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Mark Tomlinson authored
[ Upstream commit 853effc5 ] A previous commit (33f72e6f) added notification via netlink for tunnels when created/modified/deleted. If the notification returned an error, this error was returned from the tunnel function. If there were no listeners, the error code ESRCH was returned, even though having no listeners is not an error. Other calls to this and other similar notification functions either ignore the error code, or filter ESRCH. This patch checks for ESRCH and does not flag this as an error. Reviewed-by:
Hamish Martin <hamish.martin@alliedtelesis.co.nz> Signed-off-by:
Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by:
-
Eugenia Emantayev authored
[ Upstream commit 925ab1aa ] It's forbidden to manually change dev->features in run-time. Currently, this is done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when VXLAN tunnel is set. However, since the stack actually does features intersection with hw_enc_features, we can safely revert to advertizing features early when registering the netdevice. Fixes: f4a1edd5 ('net/mlx4_en: Advertize encapsulation offloads [...]') Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
