- 11 Apr, 2010 40 commits
-
-
Kashyap, Desai authored
Added sanity checks before accessing vdevice and added vdevice->deleted setting for mptfc. Signed-off-by:
Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Kashyap, Desai authored
Set factor, offset and width while target negotiation. Added config timeout 60 seconds. It was missing for only mptspi_read_spi_device_pg0 Signed-off-by:
-
Kashyap, Desai authored
Added proper bus_type check before processing event/ reset handler. Signed-off-by:
-
Kashyap, Desai authored
Current design of mptsas is as follow. MPTSAS will do probe() if pci id matches for available card in system, irrespective of mode of controller. If controller is I/T mode or I mode, things are fine. If controller is only in T mode, mptsas is not doing complete process of mptsas_probe(). It will only make sure IOC structure is created and IOC reference is available for mptstm driver. Now While removing module we should take care case of Target mode only mptsas. If we are removing IOC which is only in Target mode, We should only detach IOC instead of following rest of the cleanup process which is only required for T mode controller. Now For T mode controller, only part clean up is done instead of complete cleanup. mpt_detach will call early in case of Target mode only controller. Signed-off-by:
-
Kashyap, Desai authored
mpt_config would only attempt a MUR before retrying the command. The driver will now retry a second time with a hard reset before leaving the function. Signed-off-by:
-
Kashyap, Desai authored
Behavior changes only for IOCTLs that time out. Current behavior of Bus Reset remains the same for RAID Passthru Timeouts Current behavior of Diagnostic reset for any other type of IOCTL remains the same CHANGE: For IOCTL SCSI IOs that timeout, a Target Reset TM is sent, instead of Bus Reset. All error handing from that point is the same as what the driver currently does, which is to say that if the Device Reset TM fails it escalates do diagnostic reset. Signed-off-by:
-
Kashyap, Desai authored
Message Unit Reset - instructs the IOC to reset the Reply Post and Free FIFO's. All the Message Frames on Reply Free FIFO are discarded. All posted buffers are freed, and event notification is turned off. IOC doesnt reply to any outstanding request. This will transfer IOC to READY state. Message unit ready is less expensive operations than Hard Reset. soft reset will not force Firmware to reload again, it only do clean up of Message units. mpt_Soft_Hard_ResetHandler will first try for Soft Reset,if it fails then go for big hammer reset which is Hard Reset. Signed-off-by:
-
Kashyap, Desai authored
Upgraded version string. Signed-off-by:
-
Kashyap, Desai authored
Copyright changes for year 2010. Signed-off-by:
-
Kashyap, Desai authored
RAID_SCSI_IO_PASSTHROUGH: Driver needs to be send the default descriptor for RAID Passthru, currently its sending SCSI_IO descriptor. Signed-off-by:
-
Kashyap, Desai authored
Added proper return type values in case memory allocation failed. Signed-off-by:
-
Kashyap, Desai authored
Removed all the mutex's for ioc->tm_cmds.mutex, then created one single mutex inside the function mpt2sas_scsih_issue_tm. This is the single function used when sending task management. Also the sanity checks required for scsi mid layer escalation were moved to inside the same function because these checks need to be done while the mutex is held. The ioc->tm_cmds.mutex inside the IOCTL branch is really not required since there is another mutex in this code called for ctl_cmds handling this sync. Signed-off-by:
-
Kashyap, Desai authored
1. Fixes for little endian issues. 2. Now Debug info for Discovery event is more readable. Signed-off-by:
-
Kashyap, Desai authored
Now Driver will not treat NEEDS_INIT as failure. In addition to this, the driver will now display message to describe the the access flags when bits are set, so the end user can better understand failures. Signed-off-by:
-
Kashyap, Desai authored
Aded checks for shost_recovery flag for early return from function. Signed-off-by:
-
Kashyap, Desai authored
use the get_free_pages API for larger contigious physical memory chunk. Also, the ioc->chain_depth need to be changed from a 16bit to 32bit variable because the number of chains will exceed 64k when the queue depth is large. Signed-off-by:
-
Kashyap, Desai authored
bug fix in the handling of the internal device reset event The reason code check in scsih_sas_device_status_change_event never evaluates as true for internal device reset, hence driver never quiesce s IO when firmware is sending a device reset. The fix is to change the evaluate to: if (event_data->ReasonCode != MPI2_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET && event_data->ReasonCode != MPI2_EVENT_SAS_DEV_STAT_RC_CMP_INTERNAL_DEV_RESET) return; Signed-off-by: -
Kashyap, Desai authored
incorrect timestamp on 32 bit platforms: The upper 32 bit of the timestamp was getting truncated when converting seconds to milliseconds, which was due to the variable being long. To fix the problem, the variable needs to be u64. Also the microseconds conversion to milliseconds was incorrect; it should be divide by 1000 instead of divide by 8. Signed-off-by:
-
Kashyap, Desai authored
[SCSI] mpt2sas : Do not reset handle before calling _scsih_remove_device in RESCAN task after HBA RESET Setting handle to zero is not required before _scsih_remove_device. Driver uses sas_device->handle reference in _scsih_remove_device. Signed-off-by:
-
James Smart authored
Signed-off-by:
Alex Iannicelli <alex.iannicelli@emulex.com> Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
James Smart authored
- Enable NPIV by default. - Added code to handle unsolicited LOGO on physical port. Signed-off-by:
-
James Smart authored
Only abort outstanding I/O to force the OS to retry failed I/Os for AER uncorrectable non-fatal errors instead of reseting the adapter. Signed-off-by:
-
James Smart authored
- Add BSG support for PCI loopback testing. - Add BSG support for extended mailbox commands. Signed-off-by:
-
James Smart authored
- Correct all SLI4 code to work on big endian systems. - Move read of sli4 params earlier so returned values are used correctly. Signed-off-by:
-
James Smart authored
FCF failover improvements - Add random FCF failover when there are multiple FCFs available. - Prevent FCF log messages from being displayed for FC adapters. - Separate the New FCF and Modified FCF log messages. Signed-off-by:
-
Kei Tokunaga authored
This patch fixes some issues of mptctl_exit(). 1) It doesn't call mpt_deregister() for mptctl_taskmgmt_id => Insmoding/rmmoding mptctl.ko repeadtedly (up to MPT_MAX_PROTOCOL_DRIVERS-1 at most) can eat up all cb_idx, and that would cause a lack of MptCallbacks[], MptDriverClass[], and MptEvHandlers[]. 2) It doesn't call mpt_event_deregister() for mptctl_id => Need to call it. 3) It calls mpt_reset_deregister() for mptctl_taskmgmt_id => This could accidentally deregister an innocent reset handler that you don't want to. This patch also adds a check for mptctl_taskmgmt_id. Signed-off-by:Kei Tokunaga <tokunaga.keiich@jp.fujitsu.com> Acked-by:
-
Joe Eykholt authored
When the kernel is configured for preemption, using smp_processor_id() when preemption is enabled causes a warning backtrace and is wrong since we could move off of that CPU as soon as we get the ID, and we would be referencing the wrong CPU, and possibly an invalid one if it could be hotswapped out. Remove the fc_lport_get_stats() function and explicitly use per_cpu_ptr() to get the statistics. Where preemption has been disabled by holding a _bh lock continue to use smp_processor_id(), but otherwise use get_cpu()/put_cpu(). In fcoe_recv_frame() also changed the cases where we return in the middle to do a goto to the code which bumps ErrorFrames and does a put_cpu(). Two of these cases didn't bump ErrorFrames before, but doing so is harmless because they "can't happen", due to prior length checks. Also rearranged code in fcoe_recv_frame() to have only one call to fc_exch_recv(). It's just as efficient and saves a call to put_cpu(). In fc_fcp.c, adjusted a FIXME comment for code which doesn't need fixing. Signed-off-by:
Joe Eykholt <jeykholt@cisco.com> Signed-off-by:
Robert Love <robert.w.love@intel.com> Signed-off-by:
-
Robert Love authored
DID_ERROR cases can be ambigouos. Debugging FCP error cases will be much easier if we have debug statements when we hit these error conditions. This patch simply adds debug messages using the FC_FCP_DBG macro when we return DID_ERROR to SCSI. This way if a DID_ERROR is reproducible turning on debug_logging will give a clue to developers as to what the problem might be. Signed-off-by:
-
Vasu Dev authored
Currently fc_fcp_recv_data calls fc_fcp_retry_cmd to retry failed IO but in this case tgt is still sending data frames, therefore exchange needs to be aborted first before initiating retry. So this patch fixes this by aborting exchange first then have retry. Renames fc_timeout_error to fc_fcp_recovery since fc_timeout_error is already called from several other places beside from fcp timeout handler and then used fc_fcp_recovery for abort & retry from fc_fcp_recv_data, this rename also required renaming FC_CMD_TIME_OUT status to FC_CMD_RECOVERY to be consistent with new fc_fcp_recovery. Data frames are not expected for an DDPed exchange and potentially it could be tampered data frame, so does recovery in this case by calling fc_fcp_recovery. Signed-off-by:
Vasu Dev <vasu.dev@intel.com> Signed-off-by:
-
Vasu Dev authored
Since use of offloads is more efficient than switching to non-offload EM. However kept logic same to call em_match if it is provided in the list of EMs. Converted fc_exch_alloc to inline being now tiny a function and already not an exported libfc API any more. Signed-off-by:
-
Vasu Dev authored
In some cases seq is incremented twice causing unnecessary seq jump, for instance fc_exch_recv_seq_resp increments seq id when fc_sof_is_init is true and that is true for each incoming xfer ready but then fc_fcp_send_data does another seq increment to send data for xfer ready. This patch removes all such seq id jumps, at least it eliminates few calls to fc_seq_start_next using ex_lock. Also removes seq id update with incoming frame's seq id as this is not needed since each end (I or T) just need to send incremented their own seq id on each TSI from other end & before sending new sequence within a exchange. Signed-off-by:
-
Joe Eykholt authored
When starting a new response sequence in a multi-sequence exchange, a warning was issued that sequence initiative wasn't held. The bug was that sequence initiative was cleared by the previous sequence due to the END_SEQ flag being on. The intent may have been to check LAST_SEQ. Change just to check SEQ_INIT. Signed-off-by:
-
Joe Eykholt authored
The link and last_link fields in the fcoe_ctlr struct are no longer useful, since they are always set to the same value, and FIP always calls libfc to pass link information to the lport. Eliminate those fields and rename link_work to timer_work, since it no longer has any link change work to do. Thanks to Brian Uchino for discovering this issue. Signed-off-by:
-
Joe Eykholt authored
Remove an unused variable, mac, in fcoe_recv_frame(). Signed-off-by:
-
Joe Eykholt authored
The method we've been using for point-to-point mode requires that the LS_ACC for the FLOGI uses the D_ID and S_ID assigned to the remote port and local port, not those in the exchange. This is not the correct method, but for now, it's what works with the old target, as well as with new targets based on libfc. This patch changes the addresses used accordingly. Signed-off-by:
-
Joe Eykholt authored
When receiving a FLOGI request from a point-to-point peer, the D_ID of 0xfffffe was not recognized as belonging to one of the lports, so it was dropped. Change fc_vport_id_lookup() to treat d_id 0xfffffe as a match. Signed-off-by:
-
Joe Eykholt authored
In point-to-point mode, we need to save the source MAC from received FLOGI requests to use as the destination MAC for all outgoing frames. We stopped doing that at some point. Use the lport_set_port_id method to catch incoming FLOGI frames and pass them to fcoe_ctlr_recv_flogi() so it can save the source MAC. Signed-off-by:
-
Joe Eykholt authored
The debug message that indicated we are using non-FIP mode was being printed only if we were already in non-FIP mode. Also changed the message text to make it more clear the mode is being set, not that the message is indicating how FLOGI was received. Signed-off-by:
-
Joe Eykholt authored
In point-to-point mode, the destination MAC address for the FLOGI response was zero because the LS_ACC for the FLOGI wasn't getting intercepted by FIP. Change to call fcoe_ctlr_els_send when sending any ELS, not just requests. Signed-off-by:
-
Joe Eykholt authored
In point-to-point mode, if the PLOGI to the remote port times out, it can get deleted by the remote port module. Since there's no reference by the local port, lport->ptp_data points to a freed rport, and when the local port is reset and tries to logout again, an oops occurs in mutex_lock_nested(). Hold a reference count on the point-to-point rdata. Signed-off-by:
-
